Xerox WorkCentre 5020 DB

Рейтинг

Снят с производства

Тип устройства

МФУ

Технология печати

лазерная

Макс. формат

Число страниц в месяц

20000

Скорость печати A4

Цветность печати

черно-белая

Общие характеристики
Тип	лазерный/светодиодный
Технология печати	лазерная
Цветность печати
Область применения	малый офис
Число страниц в месяц	20 000
Макс. формат	A3
Копир
Сканер
Тип устройства	МФУ
Печать фотографий
Факс
Телефон
Размещение	настольный
Принтер
Время разогрева	27
Двусторонняя печать
Пигментные чернила
Прямая печать
Печать без полей
Макс, разрешение для ч/б печати
По X	600
По Y	600
Скорость ч/б печати
A4	20
A3	10
Время выхода первого отпечатка
Ч/б	12
Копир
Время выхода первой копии	7,5
Шаг масштабирования	0,01
Макс, количество копий за цикл	99
Значение масштаба
Минимальное	0,5
Максимальное	2
Макс, разрешение (ч/б)
По Y	600
По X	600
Сканер
Макс. формат оригинала	A3
Устройство автоподачи оригиналов	одностороннее
Стандарт TWAIN
Стандарт WIA
Отправка изображения по e-mail
Слайд-адаптер
Емкость устройства автоподачи оригиналов	50
Оттенки серого	256
Тип сканера	планшетный/протяжный
Макс, размер сканирования
По Y	432
По X	297
Разрешение сканера
По Х	600
Расходные материалы
Ресурс фотобарабана	22 000
Ресурс ч/б картриджа/тонера	6 300
Печать на:
CD/DVD
Фотобумаге
Рулоне
Глянцевой бумаге
Матовой бумаге
Этикетках
Конвертах
Пленках
Карточках
Плотность бумаги
Минимальная	60
Максимальная	110
Факс
Цветной
Телефон
Стандарт DECT
Автоответчик
Caller ID
АОН
Беспроводная трубка
Спикерфон
Проводная трубка
Языки управления
PCL 5e
PPDS
PDF
PostScript 3
PostScript
PostScript 2
PCL 5c
PCL 6
Лотки
Емкость лотка ручной подачи	50
Подача бумаги
Максимальная	800
Стандартная	300
Вывод бумаги
Стандартный	250
Финишер
Сортер
Степлер
Брошюровщик
Интерфейсы
FireWire (IEEE 1394)
Wi-Fi
Инфракрасный порт
Bluetooth
Веб-интерфейс
LPT
RS-232
Устройство для чтения карт памяти
Ethernet (RJ-45)
USB
Версия USB	2,0
Память/Процессор
Объем памяти	64
Макс, объем памяти	64
Частота процессора	400
Дополнительная информация
Работа от аккумулятора
Экран
Поддержка ОС
Linux
Windows
Mac OS
DOS
Потребляемая мощность
При работе	525
В режиме ожидания	5
Уровень шума
В режиме ожидания	28
При работе	58
Габариты
Ширина	595
Высота	605
Вес	38
Глубина	532

Коды ошибок

005-170

005-171

005-172

005-198

005-199

005-305

005-920

062-300

062-345

062-360

062-371

062-380

062-386

062-392

062-393

C0-1

C1-1

C1-2

C2-1

C2-2

C2-3

C5-0

C5-1

C6-0

C6-1

C7-1

C8-1

C8-2

C9-3

E0-1

E1-2

E1-6

E3-1

E3-6

E5-1

E5-2

E6-1

E6-2

E8-1

E8-2

H9-7

J1-0

J1-2

J3-1

J6-0

J6-1

J7-1

J7-2

J7-3

L9-0

N1-1

N4-0

N4-1

N4-2

N4-3

N5-0

N9-0

N9-1

U0-1

U1-1

U2-1

U3-5

U4-1

U4-2

U4-3

U4-9

U6-2

U6-3

U6-4

U6-5

U7-0

U7-1

U8-1

U9-0

Описание

Парткод

101R00432

106R01277

126K23581

Название

XEROX Копи-картридж / фотобарабан

XEROX Тонер-тубы 2 шт.

XEROX Узел термозакрепления 220V

Error code:	005-170
Description:	DADF Feed Failure BSD-Reference: CH 5.2. The control logic has detected the failure of paper to reach the Document Feed Sensor after the Feed Clutch has energized.
Remedy:	Check for obstructions in the Document Tray. Clean the Feed Roll. Confirm that a document is feeding into the document handler. The Feed Roller feeds paper into the document handler. Y↓N→The Document Drive Motor operates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-01]. The Document Drive Motor operates. Y↓N→There is +24 VDC at connector CN2 pin 1 and pin 4 on the DADF PWB. Y↓N→Check the following in order: 1. Check the connectors CN1 and CN2 on the DADF PWB for proper connections 2. Check the connector J414 on the SLCC PWB (AIOC) for proper connection. 3. Check the harness from the DADF PWB to the SLCC PWB for an open circuit. If the harness and the connectors are good, replace the DADF PWB Replace the Document Drive Motor (PL 13.5) The Feed Roller rotates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-62]. The Document Feed Clutch operates. Y↓N→Check the connector of the Document Feed Clutch (PL 13.9) If the connector is good, replace the Document Feed Clutch (PL 13.9). Replace the Document Feed Clutch (PL 13.9) Replace the Pick Up Roller and Feed Roller. The Feed Roller rotates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-62]. The Document Feed Clutch operates. Y↓N→Check the connector of the Document Feed Clutch (PL 13.9) If the connector is good, replace the Document Feed Clutch (PL 13.9). Replace the Document Feed Clutch (PL 13.9) Replace the Pick Up Roller and Feed Roller. Replace the Document Feed Sensor (PL 13.9).

Error code:	005-171
Description:	DADF Regi / Exit Failure BSD-Reference: CH 5.8. Control logic has detected no paper at the Registration Sensor after turning on the Registration Clutch or detected no paper at the Exit/Invert Sensor after turning on the Registration Clutch.
Remedy:	Check for obstructions in the Document Tray. Clean the Feed Roll. Confirm that a document is feeding into the document handler. The Feed Roller feeds paper into the document handler. Y↓N→The Document Drive Motor operates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-01]. The Document Drive Motor operates. Y↓N→There is +24 VDC at connector CN2 pin 1 and pin 4 on the DADF PWB. Y↓N→Check the following in order: 1. Check the connectors CN1 and CN2 on the DADF PWB for proper connections 2. Check the connector J414 on the SLCC PWB (AIOC) for proper connection. 3. Check the harness from the DADF PWB to the SLCC PWB for an open circuit. If the harness and the connectors are good, replace the DADF PWB Replace the Document Drive Motor (PL 13.5) The Feed Roller rotates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-62]. The Document Feed Clutch operates. Y↓N→Check the connector of the Document Feed Clutch (PL 13.9) If the connector is good, replace the Document Feed Clutch (PL 13.9). Replace the Document Feed Clutch (PL 13.9) Replace the Pick Up Roller and Feed Roller. The Feed Roller rotates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-62]. The Document Feed Clutch operates. Y↓N→Check the connector of the Document Feed Clutch (PL 13.9) If the connector is good, replace the Document Feed Clutch (PL 13.9). Replace the Document Feed Clutch (PL 13.9) Replace the Pick Up Roller and Feed Roller. Enter the Diagnostic Mode. Enter Component Control Code [05-206]. Actuate the Document Registration Sensor acutator. The display changes from High to Low. Y↓N→Replace the Document Registration Sensor. (PL 13.7) Enter the Diagnostic Mode. Enter Component Control Code [05-205]. Actuate the Exit/Invert Sensor actuator. The display changes from High to Low. Y↓N→Replace the Exit/Invert Sensor. (PL 13.7) Replace the DADF PWB , or replace the SLCC PWB (AIOC/Network)

Error code:	005-172
Description:	DADF Inverted Document Jam BSD-Reference: CH 5.8. When inverting documents, the control logic detected a failure of a document at the Feed Sensor after turning off the Feedout Forward or document failure at the Exit/Invert Sensor after turning on the Document Registration Sensor.
Remedy:	Check for obstructions in the Document Tray. Clean the Feed Roll. Confirm that a document is feeding into the document handler. The Feed Roller feeds paper into the document handler. Y↓N→The Document Drive Motor operates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-01]. The Document Drive Motor operates. Y↓N→There is +24 VDC at connector CN2 pin 1 and pin 4 on the DADF PWB. Y↓N→Check the following in order: 1. Check the connectors CN1 and CN2 on the DADF PWB for proper connections 2. Check the connector J414 on the SLCC PWB (AIOC) for proper connection. 3. Check the harness from the DADF PWB to the SLCC PWB for an open circuit. If the harness and the connectors are good, replace the DADF PWB Replace the Document Drive Motor (PL 13.5) The Feed Roller rotates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-62]. The Document Feed Clutch operates. Y↓N→Check the connector of the Document Feed Clutch (PL 13.9) If the connector is good, replace the Document Feed Clutch (PL 13.9). Replace the Document Feed Clutch (PL 13.9) Replace the Pick Up Roller and Feed Roller. The Feed Roller rotates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-62]. The Document Feed Clutch operates. Y↓N→Check the connector of the Document Feed Clutch (PL 13.9) If the connector is good, replace the Document Feed Clutch (PL 13.9). Replace the Document Feed Clutch (PL 13.9) Replace the Pick Up Roller and Feed Roller. Enter the Diagnostic Mode. Enter Component Control Code [05-204]. Actuate the Document Feed Sensor acutator. The display changes from High to Low. Y↓N→Replace the Document Feed Sensor. (PL 13.9) Enter the Diagnostic Mode. Enter Component Control Code [05-205]. Actuate the Exit/Invert Sensor actuator. The display changes from High to Low. Y↓N→Replace the Exit/Invert Sensor. (PL 13.7) Replace the DADF PWB , or replace the SLCC PWB (AIOC/Network)

Error code:	005-198
Description:	Too Short Size Jam RAP It was detected that the document length in Slow Scan direction was out of the specifications. • Simplex mode: shorter than 85mm • Duplex mode: shorter than 110mm
Remedy:	Check the document size a user has scanned. If its length is within the available range for DADF feeding, check the circuit between the DADF Pre Registration Sensor, the DADF Feed Out Sensor, and the DADF PWB. Check the sw version of the controller sw - update if required (GP 16). If no problems are found, replace the DADF PWB (PL 51.2).

Error code:	005-199
Description:	Too Long Size Jam RAP It was detected that the document length in Slow Scan direction was out of the specifications. • Simplex and Duplex modes: 431.9mm or longer • Fax mode: 1501.0mm or longer
Remedy:	Check the document size a user has scanned. If its length is within the available range for DADF feeding, check the circuit between the DADF Pre Registration Sensor, the DADF Feed Out Sensor, and the DADF PWB. Check the sw version of the controller sw - update if required (GP 16). If no problems are found, replace the DADF PWB (PL 51.2).

Error code:	062-360
Display:	Scanner Sensor Error Error 062-360 Restart Printer
Description:	HPSensor Error Carriage home position error
Causes:	• IIT Assembly (PL51.1.3) • IP Board (PL18.1.22)
Remedy:	1 Check the IIT Assembly connection Check the connection between the IIT Assembly and the IP Board. Are P/J1401 and P/J1501 connected securely? Go to step 2. Connect P/J1401 and P/J1501 securely. 2 Check after replacing the IIT Assembly Replace the IIT Assembly. Does the error still occur? Replace the IP Board. Finished.

Error code:	005-920
Description:	Static Jam BSD-Reference: CH 5.6. At power on, the control logic detected either the Platen Interlock is close when the Feeder Cover is open or the Feeder Cover Interlock is close when the Platen Interlock is open.
Remedy:	If this occurs frequently, confirm if there is any interferance with the Feed Sensor (PL 13.9), the Document Registration Sensor (PL 13.7) or the Exit/Invert Sensor (PL 13.7). Check the sensor connectors for prober connection. Replace one sensor at a time until the problem is solved.

Error code:	062-345
Description:	IIT/IPS Subsystem RAP The IPS EEPROM failed during a read/write operation.
Remedy:	Check the connection of each IIT/IPS PWB connector. The connectors are securely connected. Y↓N→Connect the connectors. Switch on the power. The problem persists. Y↓N→Return to Service Call Procedures. Replace the IIT/IPS PWB (PL 11.3).

Error code:	062-380
Description:	Platen AGC Fail RAP Insufficient lamp brightness was detected when performing AGC. NOTE: When turning the power OFF, turn OFF the power switch first and then the main power switch.
Remedy:	1. Turn the power ON and enter the Diag mode. Change the value for NVM location [715- 030] to "1" and then execute "NVM Write". 2. A 3 or 4-digit number is displayed in the current value column. 3. Check the upper 1 or 2 digits, or the lower 2 digits using the following table and replace the appropriate parts. Sample Display • 110 (3-digit display): LED Lamp PWB failure and LED Lamp Flexible Flat Cable is damaged or has poor contact. (The first digit "1" in "110" is the upper digit, which indicates the LED Lamp PWB ("0" in "01" is not displayed). The lower 2 digits "10" indicates the LED Lamp Flexible Flat Cable.) • 1000 (4-digit display): The LED Lamp Flexible Flat Cable is damaged or has poor contact. (The first 2 digits "10" in "1000" are the upper digits, which indicates the LED Lamp Flexible Flat Cable. The lower 2 digits "00" indicates that nothing is applicable (no failures).) NOTE: Execute the IIT diagnosis and then call NVM location [715-030] again (press the Change Settings button) to check the value (diagnosis result). 00 Not applicable (No errors) - 01 LED Lamp PWB PL 1.4 02 CCD Lens Assembly PL 1.2 03 CCD Flexible Flat Cable PL 1.2 10 LED Lamp Flexible Flat Cable PL 1.4 12 IIT-ESS Video Cable PL 18.3 14 IIT-ESS I/O Cable PL 18.3 17 LVPS-IIT/Fax Power Cable (DC Harness) PL 18.3 4. After replacing the appropriate parts, again change the value for NVM location [715-030] to "1" and then execute "NVM Write". 5. Check that the current value column becomes "000". 6. If the problem persists after performing the above procedure, continue and check the following: • LED Lamp broken: Component Control [062-002] (PL 1.2) • Check the Flat Cable between the LED Lamp PWB P/J7001 and the IIT PWB P/ J723 for open circuits, short circuits, and poor contacts (especially, check whether the Flat Cable was inserted in a skewed manner). • Check the Flat Cable between the CCD Lens Assembly P/J700 and the IIT PWB P/ J710 for open circuits, short circuits, and poor contacts (especially, check whether the Flat Cable was inserted in a skewed manner). • The coaxial cable between the IIT PWB P/J7191 and the ESS PWB P/J336 for open circuit, short circuit, and poor contact

Error code:	062-386
Description:	Platen AOC Fail RAP A CCD output error was detected when performing AOC. NOTE: When turning the power OFF, turn OFF the power switch first and then the main power switch.
Remedy:	1. Turn the power ON and enter the Diag mode. Change the value for NVM location [715- 030] to "1" and then execute "NVM Write". 2. A 3 or 4-digit number is displayed in the current value column. 3. Check the upper 1 or 2 digits, or the lower 2 digits using the following table and replace the appropriate parts. Sample Display • 110 (3-digit display): LED Lamp PWB failure and LED Lamp Flexible Flat Cable is damaged or has poor contact. (The first digit "1" in "110" is the upper digit, which indicates the LED Lamp PWB ("0" in "01" is not displayed). The lower 2 digits "10" indicates the LED Lamp Flexible Flat Cable.) • 1000 (4-digit display): The LED Lamp Flexible Flat Cable is damaged or has poor contact. (The first 2 digits "10" in "1000" are the upper digits, which indicates the LED Lamp Flexible Flat Cable. The lower 2 digits "00" indicates that nothing is applicable (no failures).) NOTE: Execute the IIT diagnosis and then call NVM location [715-030] again (press the Change Settings button) to check the value (diagnosis result). 00 Not applicable (No errors) - 01 LED Lamp PWB PL 1.4 02 CCD Lens Assembly PL 1.2 03 CCD Flexible Flat Cable PL 1.2 10 LED Lamp Flexible Flat Cable PL 1.4 12 IIT-ESS Video Cable PL 18.3 14 IIT-ESS I/O Cable PL 18.3 17 LVPS-IIT/Fax Power Cable (DC Harness) PL 18.3 4. After replacing the appropriate parts, again change the value for NVM location [715-030] to "1" and then execute "NVM Write". 5. Check that the current value column becomes "000". 6. If the problem persists after performing the above procedure, check the following: • Check the Flat Cable between the CCD Lens Assembly P/J700 and the IIT PWB P/ J710 for open circuits, short circuits, and poor contacts (especially, check whether the Flat Cable was inserted in a skewed manner). • The coaxial cable between the IIT PWB P/J7191 and the ESS PWB P/J336 for open circuit, short circuit, and poor contact If no problems are found, replace the following parts in sequence: • CCD Lens Assembly (PL 1.2) • ESS PWB (PL 35.2) • IIT PWB (Switch the EEPROM) (PL 1.6)