Toshiba e-Studio 4500c
Рейтинг
Модули
VERTICAL TRANSPORT
DUPLEX UNIT 5
Transfer Entrance 1
OPTICS SECTION 3
Original Feed 1
TANDEM TRAY 1
PAPER REGISTRATION 1
Paper Transfer 2
FRAME SECTION 1
Transfer Belt Cleaning
Universal Tray 1
Paper Transfer 1
Original Exit 1
PAPER REGISTRATION 2
Drive Section 1
DRIVE SECTION 4
DUPLEX UNIT 2
ELECTRICAL SECTION 5
OPERATION PANEL
ELECTRICAL SECTION 7
TANDEM TRAY 3
By-pass Feed 1
FRAME SECTION 2
TANDEM TRAY 2
OPTICS SECTION 2
Tonner Supply 1
Paper Exit 3
Used Tonner Section 1
ARDF Drive & Electrical 2
Frame Section 4
DRIVE SECTION 3
TRANSFER BELT UNIT 3
FUSING UNIT 2
ARDF Original Tray
DUPLEX UNIT 4
PCU 1
PCU 2
Original Trans 2
ELECTRICAL SECTION 4
DEVELOPMENT UNIT
Tonner Supply 3
DUPLEX UNIT 1
Used Tonner Section 2
EXTERIOR 2
Universal Tray 2
TRANSFER BELT UNIT 1
DRIVE SECTION 2
FUSING UNIT 1
ELECTRICAL SECTION 2
By-pass Feed 2
FUSING UNIT 3
Transfer Cover
Original Feed 2
EXTERIOR 1
Original Trans 1
ARDF Frame
ELECTRICAL SECTION 6
Tonner Supply 2
ELECTRICAL SECTION 3
Paper Exit 1
Paper Exit 4
Drive Section 5
Original Trans 3
ARDF Exterior
ELECTRICAL SECTION 1
DUPLEX UNIT 3
ELECTRICAL SECTION 8
ARDF Drive & Electrical 1
Original Exit 2
Fusing Unit 4
LASER UNIT
TRANSFER BELT UNIT 2
OPTICS SECTION 4
Paper Exit 2
Transfer Entrance 2
Transfer Entrance 3
OPTICS SECTION 1
Frame Section 3
Детали DUPLEX UNIT 3
| Деталь: | Guide:Relay:Paper Feed Un |
| Парткод: | B1326758 |
| Деталь: | Sheet:Micro Switch:12mm |
| Парткод: | B1325999 |
| Деталь: | Bracket:Micro Switch:Pape |
| Парткод: | B1325971 |
| Деталь: | TORSION SPRING |
| Парткод: | B1325869 |
| Деталь: | Screw:Micro Switch |
| Парткод: | B1325868 |
| Деталь: | Transport Unit:Vertical T |
| Парткод: | B1326751 |
| Деталь: | SPRING |
| Парткод: | AA063878 |
| Деталь: | Release Cover - Vertical |
| Парткод: | B0656429 |
| Деталь: | Decal - Grip |
| Парткод: | A0292984 |
| Деталь: | Release Lever - Vertical |
| Парткод: | B0656426 |
| Деталь: | Release Button - Vertical |
| Парткод: | B0656428 |
| Деталь: | Release Lever - Vertical |
| Парткод: | B0656427 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA143560 |
| Деталь: | Side Plate:Front:Vertical |
| Парткод: | B1326753 |
| Деталь: | Side Plate:Rear:Vertical |
| Парткод: | B1326754 |
| Деталь: | Pressure Plate:Transport |
| Парткод: | B1326752 |
| Деталь: | Transport Pressure Plate |
| Парткод: | B0656407 |
| Деталь: | Stepped Screw - M5 |
| Парткод: | AA143715 |
| Деталь: | Vertical Driven Roller |
| Парткод: | AF020295 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA080241 |
| Деталь: | Spring - 10mm |
| Парткод: | AA063487 |
| Деталь: | Transport Roller |
| Парткод: | AF020562 |
| Деталь: | Gear - 24Z/40Z |
| Парткод: | AB017619 |
| Деталь: | Gear - 35Z |
| Парткод: | AB011466 |
| Деталь: | TIMING BELT |
| Парткод: | AA043575 |
| Деталь: | Joint Unit Guide Plate As |
| Парткод: | B1406472 |
| Деталь: | Relay Unit Harness |
| Парткод: | B0656489 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | MICRO SWITCH |
| Парткод: | 12042521 |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Ball Bearing - 8x16x5 |
| Парткод: | 7423808 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Screw - M3X4 |
| Парткод: | 03530040N |
| Деталь: | Duplex Gate Pawl |
| Парткод: | B0654733 |
| Деталь: | Gate Pawl Cushion |
| Парткод: | B0654738 |
| Деталь: | Lower Duplex Guide Plate |
| Парткод: | A2944626 |
| Деталь: | SPACER |
| Парткод: | B0654865 |
| Деталь: | Stay:Timing Belt |
| Парткод: | B1324689 |
| Деталь: | Timing Belt - 40S2M810G |
| Парткод: | AA043294 |
| Деталь: | Slider:Jogger Fence:Front |
| Парткод: | B1324692 |
| Деталь: | Slider:Jogger Fence:Rear |
| Парткод: | B1324693 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW020148 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW020149 |
| Деталь: | Bracket:Sensor:Reverse:Ex |
| Парткод: | B1324715 |
| Деталь: | Gear - 30Z/45Z |
| Парткод: | AB017615 |
| Деталь: | Guide Plate:Transport:Upp |
| Парткод: | B1324710 |
| Деталь: | TENSION SPRING |
| Парткод: | AA060984 |
| Деталь: | DC Solenoid:Gate Pawl:Ass |
| Парткод: | B1324740 |
| Деталь: | Duplex Guide |
| Парткод: | A0964595 |
| Деталь: | Bracket:Support:Positioni |
| Парткод: | B1324619 |
| Деталь: | Bracket:Drawer:32pin:Dupl |
| Парткод: | B1324790 |
| Деталь: | Harness:Duplex Unit:32p |
| Парткод: | B1325261 |
| Деталь: | Bracket:Drawer:12pin:Dupl |
| Парткод: | B1324791 |
| Деталь: | Harness:Duplex Unit:12pin |
| Парткод: | B1325262 |
| Деталь: | Jogger Pulley |
| Парткод: | AB030732 |
| Деталь: | SPRING |
| Парткод: | AA062318 |
| Деталь: | Jogger Bracket |
| Парткод: | B0654820 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW020145 |
| Деталь: | Bracket:Home Position Sen |
| Парткод: | B1324699 |
| Деталь: | Tapping Screw - 4x6 |
| Парткод: | 04514006N |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 04504008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | CLAMP |
| Парткод: | 11050534 |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 11050508 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Harness Clamp - ES-0505 |
| Парткод: | 11050328 |
| Деталь: | Screw:M3x8 |
| Парткод: | 03530080N |
| Деталь: | Case:Remove Paper Dust |
| Парткод: | B1322605 |
| Деталь: | Bracket:Remove Paper Dust |
| Парткод: | B1322601 |
| Деталь: | Bracket:Registration Sens |
| Парткод: | B1322620 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW010107 |
| Деталь: | Harness:Pull Out:Uni:26pi |
| Парткод: | B1325245 |
| Деталь: | Optics Sensor:Photo |
| Парткод: | AW000010 |
| Деталь: | Stay:Registration Guide |
| Парткод: | B1322700 |
| Деталь: | Registration Guide:Upper |
| Парткод: | B1322673 |
| Деталь: | Lever:Un Lock |
| Парткод: | B1322671 |
| Деталь: | Bushing - 4x6x7mm |
| Парткод: | 54432668 |
| Деталь: | TENSION SPRING |
| Парткод: | AA060957 |
| Деталь: | TENSION SPRING |
| Парткод: | AA060962 |
| Деталь: | Side Plate:Open And Close |
| Парткод: | B1322674 |
| Деталь: | Shaft:Lock |
| Парткод: | B1322670 |
| Деталь: | Lever:Knob:Release |
| Парткод: | B1322644 |
| Деталь: | Registration Guide:Upper |
| Парткод: | B1322682 |
| Деталь: | Shaft:Contact Point:Lever |
| Парткод: | B1322681 |
| Деталь: | Knob:Release |
| Парткод: | B1322651 |
| Деталь: | Registration Guide:Connec |
| Парткод: | B1322680 |
| Деталь: | Side Plate:Open And Close |
| Парткод: | B1322669 |
| Деталь: | Cover:Drive Sub-unit |
| Парткод: | B1321188 |
| Деталь: | Harness:Dehumidifier |
| Парткод: | B1325265 |
| Деталь: | Screw:Drawer |
| Парткод: | AA143792 |
| Деталь: | Stud:Contact Point |
| Парткод: | B1322703 |
| Деталь: | Seal:Remove Paper Dust |
| Парткод: | B1322626 |
| Деталь: | Seal:Remove Paper Dust:In |
| Парткод: | B1322627 |
| Деталь: | Seal:Optics Sensor:Middle |
| Парткод: | B1322632 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Screw - M3X6 |
| Парткод: | 09513006N |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 03530060N |
| Деталь: | Clamp:LES-0505 |
| Парткод: | 11050551 |
| Деталь: | Clamp:Lwss-0504 |
| Парткод: | 11050568 |
| Деталь: | CLAMP |
| Парткод: | 11050534 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | Clamp:RFC-16V0 |
| Парткод: | 11050604 |
| Деталь: | Connector:Drawer:51405-26 |
| Парткод: | 11029387 |
| Деталь: | Retaining Ring - M2.5 |
| Парткод: | 07200025E |
| Деталь: | Carriage:No.2: Assy |
| Парткод: | B1321801 |
| Деталь: | Spring Plate - 2nd Mirror |
| Парткод: | G4042810 |
| Деталь: | Mirror:No.2 |
| Парткод: | B1321818 |
| Деталь: | Mirror:No.3 |
| Парткод: | B1321819 |
| Деталь: | Holder:Pulley |
| Парткод: | B1321815 |
| Деталь: | Pulley - High Voltage Sup |
| Парткод: | G5702834 |
| Деталь: | Original Sensor:H1-66 |
| Парткод: | AW010116 |
| Деталь: | Original Sensor:H81.5 |
| Парткод: | AW010115 |
| Деталь: | Original Sensor:H2-66 |
| Парткод: | AW010114 |
| Деталь: | Bracket:Original Sensor |
| Парткод: | B1321861 |
| Деталь: | Carriage:No.1: Assy |
| Парткод: | B1321751 |
| Деталь: | GRIP |
| Парткод: | G5702731 |
| Деталь: | Feeler:Home Position Sens |
| Парткод: | B1321766 |
| Деталь: | Holder:Connector |
| Парткод: | B1321767 |
| Деталь: | Stay:Wire |
| Парткод: | B1321758 |
| Деталь: | REFLECTOR |
| Парткод: | B1321762 |
| Деталь: | 1st Mirror Holder |
| Парткод: | A1931767 |
| Деталь: | Mirror:No.1:Assy |
| Парткод: | B1321757 |
| Деталь: | Harness:Connecting:Scanne |
| Парткод: | B1325304 |
| Деталь: | Xenon Lamp:10000 0LX |
| Парткод: | B1321890 |
| Деталь: | Tapping Screw:Round Point |
| Парткод: | 8025291 |
| Деталь: | Philips Pan Head Screw - |
| Парткод: | 03130050N |
| Деталь: | Screw - M3X6 |
| Парткод: | 09513006N |
| Деталь: | Screw - M4X8 |
| Парткод: | 09544008N |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | Guide:Paper Feed:Upper |
| Парткод: | B4772342 |
| Деталь: | Decal:Misfeed Removal:Pap |
| Парткод: | B6521811 |
| Деталь: | Decal:Display Guidance |
| Парткод: | B6521812 |
| Деталь: | Decal:Size:Original |
| Парткод: | B6521807 |
| Деталь: | Paper Feed Cover Grip |
| Парткод: | B4771821 |
| Деталь: | Paper Feed Release Lever |
| Парткод: | B4771825 |
| Деталь: | SPRING |
| Парткод: | B4774117 |
| Деталь: | Grip Shaft |
| Парткод: | B4771831 |
| Деталь: | Bracket:Pressure:Pickup |
| Парткод: | B6521822 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B6521824 |
| Деталь: | Pressure Plate:Pickup |
| Парткод: | B6521823 |
| Деталь: | Rear Cover Bracket |
| Парткод: | B4771851 |
| Деталь: | Front Cover Bracket |
| Парткод: | B4771841 |
| Деталь: | Pin:Guide Plate:Paper Fee |
| Парткод: | AA143788 |
| Деталь: | Paper feed Cover |
| Парткод: | B4771791 |
| Деталь: | Pull Out Roller Bracket |
| Парткод: | B4772361 |
| Деталь: | ANTI-STATIC BRUSH |
| Парткод: | B4772491 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA080037 |
| Деталь: | SPRING |
| Парткод: | B4774111 |
| Деталь: | Driven Pull Out Roller |
| Парткод: | B4772351 |
| Деталь: | ANTISTATIC BRUSH |
| Парткод: | A6972131 |
| Деталь: | Bracket:Paper Size Sensor |
| Парткод: | B6522523 |
| Деталь: | Photointerruptor:Paper Si |
| Парткод: | AW020155 |
| Деталь: | PHOTOINTERRUPTOR:ENTRANCE |
| Парткод: | AW020154 |
| Деталь: | Harness:Paper Size Sensor |
| Парткод: | B6525411 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW010107 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW010117 |
| Деталь: | Harness:Sensor:Stopper Gu |
| Парткод: | B6525416 |
| Деталь: | Relay Roller Arm |
| Парткод: | B4772373 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B6522505 |
| Деталь: | Driven Paper Feed Roller |
| Парткод: | B4772372 |
| Деталь: | Decal -Paper Tray 1 |
| Парткод: | B0656635 |
| Деталь: | Cover:Tandem LCT |
| Парткод: | B1326671 |
| Деталь: | Tandem LCT Unit:Left (NA) |
| Парткод: | B1327513 |
| Деталь: | LEFT SIDE PLATE |
| Парткод: | A2946645 |
| Деталь: | Bracket:Cover:Tandem LCT: |
| Парткод: | B0706516 |
| Деталь: | Decal - Paper Set - Left |
| Парткод: | B0656846 |
| Деталь: | Left Front Fence |
| Парткод: | A2946643 |
| Деталь: | Tray Bottom Plate:Left Fr |
| Парткод: | B1327540 |
| Деталь: | Tray Bottom Plate:Left Mi |
| Парткод: | B0986639 |
| Деталь: | Tray Bottom Plate:Left Re |
| Парткод: | B1327541 |
| Деталь: | Decal - Left Paper Set |
| Парткод: | A0966678 |
| Деталь: | Left Rear Fence |
| Парткод: | A2946630 |
| Деталь: | Decal - Paper Level |
| Парткод: | AA002010 |
| Деталь: | Stopper - Interlock Switc |
| Парткод: | A2946650 |
| Деталь: | Timing Pulley - 15T |
| Парткод: | AB033085 |
| Деталь: | Pulley Braket |
| Парткод: | B0656821 |
| Деталь: | Tension Spring:Timing Bel |
| Парткод: | AA060987 |
| Деталь: | Shaft - Back Fence Slider |
| Парткод: | AA140685 |
| Деталь: | Slider:Back Fence:Left |
| Парткод: | B1327564 |
| Деталь: | Timing Belt Cover |
| Парткод: | B0656823 |
| Деталь: | Back Fence:Left |
| Парткод: | B1327561 |
| Деталь: | Timing Belt S3M 196T |
| Парткод: | AA043271 |
| Деталь: | Pulley Bracket |
| Парткод: | B0656830 |
| Деталь: | Gear - 48T |
| Парткод: | AB019475 |
| Деталь: | Timing Pulley - 15T |
| Парткод: | AB033084 |
| Деталь: | DC Harness - Left |
| Парткод: | B0705473 |
| Деталь: | Shaft - Timing Pulley |
| Парткод: | AA140686 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50530447 |
| Деталь: | Gear - Z18 |
| Парткод: | AB013798 |
| Деталь: | Left DC Motor Bracket |
| Парткод: | B0706666 |
| Деталь: | DC Motor:Tandem LCT |
| Парткод: | AX040145 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW020163 |
| Деталь: | Base:Tandem LCT:Left:Ass |
| Парткод: | B0656832 |
| Деталь: | Bracket:Photointerruptor: |
| Парткод: | B1327566 |
| Деталь: | Coupling Lever - Left |
| Парткод: | A2486615 |
| Деталь: | Screw:Polished Round:M4x8 |
| Парткод: | 09514008N |
| Деталь: | Pan Self-tapping Screw:M4 |
| Парткод: | 04340060N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Tapping Screw:M4x8 |
| Парткод: | 04524008N |
| Деталь: | Binding Self-tapping Scre |
| Парткод: | 04524010N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 04503008N |
| Деталь: | Pan Head Screw:M3x8 |
| Парткод: | 03130080N |
| Деталь: | Harness Clamp - ES-0505 |
| Парткод: | 11050328 |
| Деталь: | CLAMP |
| Парткод: | 11050230 |
| Деталь: | PAPER FEED UNIT |
| Парткод: | B1326621 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Paper Feed Roller:Pickup |
| Парткод: | AF030081 |
| Деталь: | Paper Feed Roller:Feed |
| Парткод: | AF031082 |
| Деталь: | Pick-up Gear Cover |
| Парткод: | B0656350 |
| Деталь: | Idler Gear |
| Парткод: | AB011465 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA082118 |
| Деталь: | Pick-up Arm |
| Парткод: | B0656357 |
| Деталь: | SPRING |
| Парткод: | AA060898 |
| Деталь: | Feed Roller Shaft |
| Парткод: | AA140828 |
| Деталь: | Feed Lever |
| Парткод: | B0656445 |
| Деталь: | SPRING |
| Парткод: | AA060897 |
| Деталь: | Paper Feed Sensor Bracket |
| Парткод: | B0656358 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW010107 |
| Деталь: | Feed Stay |
| Парткод: | B0656364 |
| Деталь: | Upper Paper Feed Harness |
| Парткод: | B0656488 |
| Деталь: | SPRING |
| Парткод: | AA060899 |
| Деталь: | DC Solenoid:Pickup:Assy |
| Парткод: | B1326659 |
| Деталь: | Gear - 21Z/38Z |
| Парткод: | AB017617 |
| Деталь: | Paper End Sensor Bracket |
| Парткод: | B0656345 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW020160 |
| Деталь: | Lower Paper Feed Harness |
| Парткод: | B0656487 |
| Деталь: | Paper Feed Guide Plate |
| Парткод: | B1406339 |
| Деталь: | Transport Roller |
| Парткод: | AF020562 |
| Деталь: | Gear - 35Z |
| Парткод: | AB011466 |
| Деталь: | Heat Sink Base |
| Парткод: | B0656334 |
| Деталь: | Heat Sink Spring |
| Парткод: | AA063889 |
| Деталь: | HEAT SINK |
| Парткод: | B0656337 |
| Деталь: | Heat Sink Sheet |
| Парткод: | B0656338 |
| Деталь: | Paper Feed Unit Stay |
| Парткод: | B0656375 |
| Деталь: | Drive bracket |
| Парткод: | B0656366 |
| Деталь: | Feed Gear Cover |
| Парткод: | B0656353 |
| Деталь: | Driven Pressure Lever |
| Парткод: | B0656457 |
| Деталь: | SPRING |
| Парткод: | AA060896 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA143718 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Screw - M3X4 |
| Парткод: | 03530040N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Ball Bearing - 8x16x5 |
| Парткод: | 7423808 |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Harness Clamp - ES-0505 |
| Парткод: | 11050328 |
| Деталь: | Harness Clamp - MSBS-1207 |
| Парткод: | 11050542 |
| Деталь: | Connector - 9P |
| Парткод: | 11026252 |
| Деталь: | Connector - 8P |
| Парткод: | 11026251 |
| Деталь: | Relay Connector - 6P |
| Парткод: | 11026249 |
| Деталь: | Transport Unit:Assy |
| Парткод: | B1323850 |
| Деталь: | Transport Belt |
| Парткод: | AA040033 |
| Деталь: | Transport Roller:Driven |
| Парткод: | AF022064 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA082101 |
| Деталь: | Transport Roller:Drive |
| Парткод: | B1323851 |
| Деталь: | Supporting Plate:Vacuum |
| Парткод: | B1323862 |
| Деталь: | Fan Motor MM60/l5mm:24V |
| Парткод: | AX640158 |
| Деталь: | Harness:Transport Belt:Fa |
| Парткод: | B1325248 |
| Деталь: | Collection Coil:Toner:Ass |
| Парткод: | B1326260 |
| Деталь: | Tray:Toner Catchpan:Assy |
| Парткод: | B1326257 |
| Деталь: | Stay:Pull Out |
| Парткод: | B1326304 |
| Деталь: | Gear:30T |
| Парткод: | AB017338 |
| Деталь: | Timing Belt:S2M208 |
| Парткод: | AA043578 |
| Деталь: | Pulley:31T |
| Парткод: | AB030275 |
| Деталь: | Stopper:Transfer/Separati |
| Парткод: | B1326286 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Pulley:40T |
| Парткод: | AB030748 |
| Деталь: | Holder:Heater |
| Парткод: | B1326507 |
| Деталь: | Heat Sink:Heater:Toner |
| Парткод: | B1326506 |
| Деталь: | Cover:Heater |
| Парткод: | B1326508 |
| Деталь: | Toner Hopper Shield |
| Парткод: | AA153448 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw:3x20 |
| Парткод: | 04513020N |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 04504008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 04503010N |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | Heater:115V:18W:Upper |
| Парткод: | AX400176 |
| Деталь: | Heater:240V:18W:Upper |
| Парткод: | AX400178 |
| Деталь: | Slide Rail:Toner Supply:A |
| Парткод: | AA070064 |
| Деталь: | Sheet:Stay |
| Парткод: | B1326949 |
| Деталь: | Stay:Intermediate Transfe |
| Парткод: | B1321003 |
| Деталь: | Duct: Fusing :Upper |
| Парткод: | B1322426 |
| Деталь: | Duct:Imaging Unit:Exhaust |
| Парткод: | B1326958 |
| Деталь: | Duct:Imaging Unit:Sub-ass |
| Парткод: | B1326978 |
| Деталь: | Duct:Imaging Unit:1st:Ass |
| Парткод: | B1326971 |
| Деталь: | Duct:Imaging Unit:Exhaust |
| Парткод: | B1326965 |
| Деталь: | Cover: Duct: Imaging Unit :A |
| Парткод: | B1326980 |
| Деталь: | Duct:Imaging Unit:23st:As |
| Парткод: | B1326973 |
| Деталь: | Duct:Imaging Unit:4st:Ass |
| Парткод: | B1326975 |
| Деталь: | Duct:Humidity Control:Ass |
| Парткод: | B1322470 |
| Деталь: | Bracket:Exhaust:Harness |
| Парткод: | B1326867 |
| Деталь: | Bracket:Hinge:Door |
| Парткод: | B1321462 |
| Деталь: | Turret Spring |
| Парткод: | AA063052 |
| Деталь: | Hinge Shaft |
| Парткод: | A0961355 |
| Деталь: | Screw:M4 |
| Парткод: | AA143545 |
| Деталь: | Duct:Fusing:Side :Assy |
| Парткод: | B1326896 |
| Деталь: | Screw:Safety |
| Парткод: | AA143791 |
| Деталь: | Heat Pipe:Assy |
| Парткод: | B1326884 |
| Деталь: | Duct:Fusing:Exit:Upper:Le |
| Парткод: | B1326917 |
| Деталь: | Duct: Fusing: Exit: Upper |
| Парткод: | B1326892 |
| Деталь: | Duct:Exit :Upper:Left :Ass |
| Парткод: | B1326908 |
| Деталь: | Duct: Exit :Upper |
| Парткод: | B1326912 |
| Деталь: | Decal - Y Toner Supply |
| Парткод: | GA003016 |
| Деталь: | Decal - C Toner Supply |
| Парткод: | GA003018 |
| Деталь: | Decal - M Toner Supply |
| Парткод: | GA003017 |
| Деталь: | Decal - K Toner Supply |
| Парткод: | GA003019 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Screw-m4x6 |
| Парткод: | 03540060N |
| Деталь: | Screw:M4x8 |
| Парткод: | 03540080N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Clamp:LWSS- 1N |
| Парткод: | 11050598 |
| Деталь: | Bushing:LE-60 |
| Парткод: | 11060901 |
| Деталь: | Toner Collection Coil |
| Парткод: | AD043086 |
| Деталь: | Case:Belt Cleaning:Assy |
| Парткод: | B1326499 |
| Деталь: | Holder:Spring:Roller:Pres |
| Парткод: | B1326459 |
| Деталь: | Spring:Roller:Pressure |
| Парткод: | AA063423 |
| Деталь: | Case:Spring:Roller:Pressu |
| Парткод: | B1326460 |
| Деталь: | Gear:12Z |
| Парткод: | AB013296 |
| Деталь: | Bushing:Holder:Blade |
| Парткод: | AA083021 |
| Деталь: | Ground Plate:Belt Cleanin |
| Парткод: | B1326462 |
| Деталь: | Spring:Joint:Discharge Us |
| Парткод: | AA063442 |
| Деталь: | Joint:Discharge Used Tone |
| Парткод: | B1326461 |
| Деталь: | Roller:Pressure |
| Парткод: | B1326469 |
| Деталь: | Shield:Case:Belt Cleaning |
| Парткод: | AA152371 |
| Деталь: | Shield:Case:Belt Cleaning |
| Парткод: | AA152370 |
| Деталь: | Belt Cleaning Blade |
| Парткод: | AD041107 |
| Деталь: | Spring:Blade:Belt Cleanin |
| Парткод: | AA060094 |
| Деталь: | Holder:Blade:Belt Cleanin |
| Парткод: | B1326470 |
| Деталь: | Joint:Drive:Brush:Belt Cl |
| Парткод: | B1326475 |
| Деталь: | Seal:Upper:Belt Cleaning |
| Парткод: | B1326120 |
| Деталь: | Cover:Case:Coating Bar |
| Парткод: | B1326453 |
| Деталь: | Brush:Belt Cleaning |
| Парткод: | AD042071 |
| Деталь: | Bushing: Brush: Rear |
| Парткод: | AA080279 |
| Деталь: | Case:Coating Bar:Assy |
| Парткод: | B1326450 |
| Деталь: | Belt Cleaning Scraper Bla |
| Парткод: | AD041109 |
| Деталь: | Roller:Bias |
| Парткод: | B1326468 |
| Деталь: | Receptacle:Brush:Assy |
| Парткод: | B1326454 |
| Деталь: | Gear - 13Z |
| Парткод: | AB013298 |
| Деталь: | Gear - 13Z |
| Парткод: | AB013297 |
| Деталь: | Gear - 13Z |
| Парткод: | AB013295 |
| Деталь: | Bushing: Brush: Front |
| Парткод: | AA080278 |
| Деталь: | Shield:Cover:Coating Bar: |
| Парткод: | AA152368 |
| Деталь: | Snap Ring |
| Парткод: | G0111058 |
| Деталь: | Shield: Brush: Front |
| Парткод: | AA152366 |
| Деталь: | Seal:Brush:Rear |
| Парткод: | AA152316 |
| Деталь: | Seal:Case:Coating Bar |
| Парткод: | AA152372 |
| Деталь: | Stay:Roller:Pressure:Fron |
| Парткод: | B1326484 |
| Деталь: | Stay:Roller:Pressure:Rear |
| Парткод: | B1326485 |
| Деталь: | Screw - M3X6 |
| Парткод: | 03603006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 07200030E |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 04503006N |
| Деталь: | Slide Rail:Right:Assy |
| Парткод: | B1326693 |
| Деталь: | Decal - Paper Tray 2 |
| Парткод: | B0656636 |
| Деталь: | Decal- Paper Tray 3 |
| Парткод: | B0656637 |
| Деталь: | Slide Rail:Left:Sub-assy |
| Парткод: | B1326692 |
| Деталь: | Paper Tray Cover - Long |
| Парткод: | B0656632 |
| Деталь: | Paper Tray Cover - Short |
| Парткод: | B0656633 |
| Деталь: | Left Support Plate |
| Парткод: | B0656589 |
| Деталь: | Right Support Plate |
| Парткод: | B0656588 |
| Деталь: | Paper Tray Holder Base |
| Парткод: | B0656591 |
| Деталь: | Stay:Holder:Paper Tray:As |
| Парткод: | B1326653 |
| Деталь: | Total Counter: 7FIG :24V:MI |
| Парткод: | AX310047 |
| Деталь: | Bracket:Total Counter |
| Парткод: | B1325976 |
| Деталь: | Decal:Total Counter |
| Парткод: | B1325996 |
| Деталь: | Base:Slide Rail:No.2:Peen |
| Парткод: | B0656781 |
| Деталь: | Tray Lock Spring - 19mm |
| Парткод: | AA060534 |
| Деталь: | Tray Lock Arm |
| Парткод: | B0656136 |
| Деталь: | Slide Rail Base |
| Парткод: | B0656783 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 04513008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 04533006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | STEPPED SCREW |
| Парткод: | 54472769 |
| Деталь: | Paper Discharge Plate |
| Парткод: | B1326268 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA143716 |
| Деталь: | Stay:Brush Roller:Assy |
| Парткод: | B1326253 |
| Деталь: | Stay:Transfer Unit |
| Парткод: | B1326274 |
| Деталь: | Shaft:Contact Point |
| Парткод: | B1326287 |
| Деталь: | TRANSFER ROLLER |
| Парткод: | B1326340 |
| Деталь: | Gear:40Z |
| Парткод: | B1326303 |
| Деталь: | Spring:Pressure |
| Парткод: | B1326306 |
| Деталь: | PTR Cleaning Brush |
| Парткод: | B1326255 |
| Деталь: | Bushing:6x10x6 |
| Парткод: | AA082137 |
| Деталь: | Guide Plate:Entrance:Ass |
| Парткод: | B1326295 |
| Деталь: | Shield:Guide Plate:Entran |
| Парткод: | B1326323 |
| Деталь: | PTR Lubricant Bar |
| Парткод: | B1326330 |
| Деталь: | PTR Cleaning Blade |
| Парткод: | B1326265 |
| Деталь: | Holder:Blade |
| Парткод: | B1326269 |
| Деталь: | Spring:Blade |
| Парткод: | B1326299 |
| Деталь: | Gear:40Z |
| Парткод: | B1326301 |
| Деталь: | Joint: Transfer: Drive |
| Парткод: | B1326284 |
| Деталь: | Gear:40Z |
| Парткод: | B1326302 |
| Деталь: | Bracket:Gear:Idler |
| Парткод: | B1326311 |
| Деталь: | Base:Transfer Roller:Rear |
| Парткод: | B1326307 |
| Деталь: | Spring:Pressure |
| Парткод: | B1326288 |
| Деталь: | Gear:21Z |
| Парткод: | AB011124 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Timing Belt:S2M170 |
| Парткод: | AA043587 |
| Деталь: | Pulley:23T |
| Парткод: | AB030749 |
| Деталь: | Supporting Plate:Pull Out |
| Парткод: | B1321186 |
| Деталь: | Gear:20/29Z |
| Парткод: | AB011125 |
| Деталь: | Gear:20Z |
| Парткод: | AB011126 |
| Деталь: | Basefront |
| Парткод: | B1326314 |
| Деталь: | Rear bushing |
| Парткод: | AA080154 |
| Деталь: | Spring: Tightener: Transpor |
| Парткод: | B1326337 |
| Деталь: | Pulley:Belt Tensioner |
| Парткод: | A2576112 |
| Деталь: | Tightener:Transfer:Transp |
| Парткод: | B1326331 |
| Деталь: | Side Plate:Positioning:Tr |
| Парткод: | B1326334 |
| Деталь: | Seal:Guide Plate:Entrance |
| Парткод: | B1326327 |
| Деталь: | Seal:Side Plate:Rear |
| Парткод: | B1326326 |
| Деталь: | Seal:Side Plate:Front |
| Парткод: | B1326325 |
| Деталь: | Screw - M3X6 |
| Парткод: | 03603006N |
| Деталь: | Tapping Screw:M4x14 |
| Парткод: | 04514014N |
| Деталь: | Screw:M4x8 |
| Парткод: | 03540080N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Parallel Pin - 3x12 |
| Парткод: | 06330120G |
| Деталь: | Bushing 8mm |
| Парткод: | 8053511 |
| Деталь: | Washer DIA6 |
| Парткод: | 07010060N |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52062684 |
| Деталь: | Guide Plate:Lower:Pull Ou |
| Парткод: | B6522152 |
| Деталь: | Decal:Guide Plate:Reverse |
| Парткод: | B6524119 |
| Деталь: | Guide Plate:Reverse:Exit: |
| Парткод: | B6524114 |
| Деталь: | Guide:Reverse:Exit |
| Парткод: | B6524116 |
| Деталь: | Guide:Reverse:Exit:Middle |
| Парткод: | B6524117 |
| Деталь: | Guide Plate:Reverse:Middl |
| Парткод: | B6524115 |
| Деталь: | Guide Plate:Reverse:Entra |
| Парткод: | B6524103 |
| Деталь: | Reverse Roller:Exit:Drive |
| Парткод: | B6524152 |
| Деталь: | EXIT ROLLER |
| Парткод: | B6524726 |
| Деталь: | Paper Feed Sensor Bracket |
| Парткод: | B4772495 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW010117 |
| Деталь: | Harness:Sensor:Exit |
| Парткод: | B6525461 |
| Деталь: | Guide: Scanning: Exit: Long |
| Парткод: | B6524506 |
| Деталь: | Guide: Scanning: Exit: Short |
| Парткод: | B6524507 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A4221063 |
| Деталь: | Guide: Scanning: Exit: Exit |
| Парткод: | B6524501 |
| Деталь: | Discharge Brush:Exit:L37 |
| Парткод: | B6524503 |
| Деталь: | Discharge Brush:Exit:L16 |
| Парткод: | B6524504 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50530447 |
| Деталь: | Ball Bearing - 6x13x5 |
| Парткод: | A8592230 |
| Деталь: | Timing Pulley:44t |
| Парткод: | B6524727 |
| Деталь: | Pin:Guide Plate:Paper Fee |
| Парткод: | AA143788 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Timing Pulley - T28 S2M |
| Парткод: | A8062111 |
| Деталь: | PIN |
| Парткод: | C1051866 |
| Деталь: | Guide Bracket |
| Парткод: | B4772145 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Tapping Screw:Round Point |
| Парткод: | 8025291 |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 04513010N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Parallel Pin - 2x12 |
| Парткод: | 06320120G |
| Деталь: | Retaining Ring - 3m |
| Парткод: | 8050092 |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | GUIDE PLATE |
| Парткод: | B0656372 |
| Деталь: | Transport Roller |
| Парткод: | AF022149 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA080327 |
| Деталь: | Driven Shaft |
| Парткод: | AA140829 |
| Деталь: | Transport Roller Lever |
| Парткод: | B0656453 |
| Деталь: | Screw - Scale |
| Парткод: | AA143812 |
| Деталь: | Driven Release Lever |
| Парткод: | B0656454 |
| Деталь: | Driven Pressure Lever |
| Парткод: | B0656455 |
| Деталь: | Front Side Plate - Paper |
| Парткод: | B0656336 |
| Деталь: | Support Guide Plate |
| Парткод: | B0656371 |
| Деталь: | Relay Shaft |
| Парткод: | B0656317 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA082118 |
| Деталь: | Gear - 19Z |
| Парткод: | AB011469 |
| Деталь: | Rear Side Plate - Paper F |
| Парткод: | B0656330 |
| Деталь: | Gear - 18Z |
| Парткод: | AB011470 |
| Деталь: | Tray Link Guide |
| Парткод: | B0656452 |
| Деталь: | Paper Tray Link |
| Парткод: | B0656346 |
| Деталь: | Arm Screw |
| Парткод: | 58942540 |
| Деталь: | SPRING |
| Парткод: | AA060900 |
| Деталь: | Pulley:Idler:30t/24z |
| Парткод: | AB017690 |
| Деталь: | TIMING BELT |
| Парткод: | AA043575 |
| Деталь: | Vertical Transport Link |
| Парткод: | B0656456 |
| Деталь: | SPRING |
| Парткод: | AA060901 |
| Деталь: | Ground Plate:Stepper Moto |
| Парткод: | B1406378 |
| Деталь: | Stepper Motor:Paper Feed |
| Парткод: | B1326655 |
| Деталь: | MOTOR BRACKET |
| Парткод: | B0656394 |
| Деталь: | SPRING |
| Парткод: | AA060904 |
| Деталь: | Motor Base |
| Парткод: | B0656415 |
| Деталь: | Pulley - 20T |
| Парткод: | AB030733 |
| Деталь: | TIMING BELT |
| Парткод: | AA043576 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Paper Feed Roller:Separat |
| Парткод: | AE,032080 |
| Деталь: | Torque Limiter - 53mnxm |
| Парткод: | A2946700 |
| Деталь: | Reverse Driven Shaft |
| Парткод: | B0656307 |
| Деталь: | Driven Reverse Gear - 21Z |
| Парткод: | AB011391 |
| Деталь: | Reverse Gear |
| Парткод: | AB011471 |
| Деталь: | Reverse Drive Shaft |
| Парткод: | B0656306 |
| Деталь: | Gear - 21Z |
| Парткод: | AB011491 |
| Деталь: | Gear - 38Z |
| Парткод: | AB011490 |
| Деталь: | Pulley - 30Z |
| Парткод: | AB030734 |
| Деталь: | Ground Plate:Reverse:Pape |
| Парткод: | B1406377 |
| Деталь: | DC Solenoid:Reverse:Assy |
| Парткод: | B1326670 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 04504008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Screw - M3X4 |
| Парткод: | 03530040N |
| Деталь: | Ball Bearing - 6x12x4mm |
| Парткод: | 7413506 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Hexagon Headless Set Scre |
| Парткод: | 05730030E |
| Деталь: | Harness Clamp - ES-0505 |
| Парткод: | 11050328 |
| Деталь: | DC Motor:Drive:Transfer |
| Парткод: | B1321330 |
| Деталь: | DC Motor:On-off:Assy |
| Парткод: | B1321338 |
| Деталь: | Collar:Joint:Drive |
| Парткод: | B1322488 |
| Деталь: | Joint:Drive:K |
| Парткод: | B1322487 |
| Деталь: | Joint:Drive |
| Парткод: | B1322486 |
| Деталь: | Drum Shaft:K |
| Парткод: | B1322491 |
| Деталь: | Drum Shaft |
| Парткод: | B1322481 |
| Деталь: | Bracket:On-Off:Plate |
| Парткод: | B1321339 |
| Деталь: | DC Motor:Drum:DIA87:Assy |
| Парткод: | B1322493 |
| Деталь: | Stud: Drive: Motor: Drum |
| Парткод: | B1321264 |
| Деталь: | DC Motor:MM63:24W |
| Парткод: | AX060280 |
| Деталь: | BRACKET:DRIVE |
| Парткод: | B1321260 |
| Деталь: | Gear:Pulley:60Z/36T |
| Парткод: | AB017681 |
| Деталь: | TENSION SPRING |
| Парткод: | AA060950 |
| Деталь: | Bracket:Tightener:Drive |
| Парткод: | B1321266 |
| Деталь: | Timing Pulley:44t |
| Парткод: | AB030767 |
| Деталь: | Timing Belt:60S2M396 |
| Парткод: | AA043963 |
| Деталь: | Pulley:Idler |
| Парткод: | B1321282 |
| Деталь: | Timing Pulley:37T |
| Парткод: | AB030766 |
| Деталь: | Shaft:Drive:Brush Roller: |
| Парткод: | B1321275 |
| Деталь: | Shaft:Drive :Development :A |
| Парткод: | B1321270 |
| Деталь: | Bracket: Auxil iary: Drive |
| Парткод: | B1321265 |
| Деталь: | Seal:Duct:Side Plate:Rear |
| Парткод: | B1322467 |
| Деталь: | Duct:Side Plate:Rear:Rear |
| Парткод: | B1322421 |
| Деталь: | Duct:Side Plate:Rear:Fron |
| Парткод: | B1322420 |
| Деталь: | Screw:M4x10 |
| Парткод: | 03604010N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Screw - M4X6 |
| Парткод: | 03604006N |
| Деталь: | Screw:M3x12 |
| Парткод: | 03603012P |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | Harness Clamp |
| Парткод: | 11050488 |
| Деталь: | Ball Bearing - 6x14x5mm |
| Парткод: | 7423906 |
| Деталь: | Ball Bearing - 8x22x7 |
| Парткод: | 7403008 |
| Деталь: | Stepped Screw - M3x26.5 |
| Парткод: | A5551671 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B1326550 |
| Деталь: | Bracket:Used Toner Sensor |
| Парткод: | B1326547 |
| Деталь: | Oil End Sensor |
| Парткод: | AW020164 |
| Деталь: | Harness:Bank:Middle |
| Парткод: | B1325394 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B1326566 |
| Деталь: | Gear - 30Z |
| Парткод: | AB013467 |
| Деталь: | Bracket:Used Toner Sensor |
| Парткод: | B1326525 |
| Деталь: | Bracket:Dc Motor:No.2 |
| Парткод: | B1326544 |
| Деталь: | Gear:17/51Z |
| Парткод: | AB017000 |
| Деталь: | Shaft:Idler:DC Motor |
| Парткод: | B1326593 |
| Деталь: | DC Motor:On-Off:Assy (B1 |
| Парткод: | B1803991 |
| Деталь: | DC Motor:Rise:Paper Tray |
| Парткод: | AX040144 |
| Деталь: | Paper Tray Positioning Br |
| Парткод: | B0656174 |
| Деталь: | Paper Tray Stopper |
| Парткод: | B0656172 |
| Деталь: | Bracket:Paper Size Sensor |
| Парткод: | B1326737 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW500010 |
| Деталь: | Harness:Bank:Tray:Paper S |
| Парткод: | B1325397 |
| Деталь: | Bracket:Power Supply Unit |
| Парткод: | B1325977 |
| Деталь: | Bracket:Earth:Power Suppl |
| Парткод: | B1325827 |
| Деталь: | Bracket:Power Supply Unit |
| Парткод: | B1325997 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Screw:M4x8 |
| Парткод: | 03540080N |
| Деталь: | Screw:M3X3 |
| Парткод: | Q353QQ3QN |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 04513008N |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 11050508 |
| Деталь: | Edge Saddle:Les-2017 |
| Парткод: | 11050544 |
| Деталь: | Harness Clamp - IWS-2218 |
| Парткод: | 11050490 |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Harness Clamp |
| Парткод: | 11050488 |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 07200030E |
| Деталь: | Shoulder Screw - Front Co |
| Парткод: | AA143129 |
| Деталь: | SPRING |
| Парткод: | AA062318 |
| Деталь: | Decal:Grip:E3 |
| Парткод: | B1324796 |
| Деталь: | Lever:Open And Close:Reve |
| Парткод: | B1324647 |
| Деталь: | Release Lever |
| Парткод: | AG051141 |
| Деталь: | Lower Entrance Guide Plat |
| Парткод: | A2294623 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA063579 |
| Деталь: | Bushing - 4x5x7 |
| Парткод: | AA080034 |
| Деталь: | Duplex Driven Roller |
| Парткод: | A2294624 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA082118 |
| Деталь: | Bushing - M8 |
| Парткод: | AA082116 |
| Деталь: | Side Plate:Front:Reverse |
| Парткод: | B1324627 |
| Деталь: | Tension Spring:Black |
| Парткод: | AA062328 |
| Деталь: | Entrance Inverter Roller |
| Парткод: | AF021074 |
| Деталь: | Spacer:Gate Pawl |
| Парткод: | B1324643 |
| Деталь: | Front Gate Pawl |
| Парткод: | A2934613 |
| Деталь: | Reverse Roller |
| Парткод: | A2934611 |
| Деталь: | Rear Gate Pawl |
| Парткод: | A2934614 |
| Деталь: | Side Plate:Rear:Reverse U |
| Парткод: | B1324620 |
| Деталь: | Joint Holder |
| Парткод: | B0654632 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA063582 |
| Деталь: | Drive Joint |
| Парткод: | A2294740 |
| Деталь: | Sensor bracket |
| Парткод: | B0654644 |
| Деталь: | Duplex Discharge Brush |
| Парткод: | A2294617 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW010119 |
| Деталь: | Harness:Sensor:Reverse Un |
| Парткод: | B1324985 |
| Деталь: | Guide Plate:Entrance :Uppe |
| Парткод: | B1324640 |
| Деталь: | Stopped Screw - M4x17 |
| Парткод: | AA143426 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Screw-m4x6 |
| Парткод: | 03540060N |
| Деталь: | Screw-m3x5 |
| Парткод: | 03530050N |
| Деталь: | Tapping Screw:M4x10 |
| Парткод: | 04504010N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Harness Clamp - ES-0505 |
| Парткод: | 11050328 |
| Деталь: | Bracket:Fix:C/T Box:Lower |
| Парткод: | B1325912 |
| Деталь: | Bracket:Fix:C/T Box:Lower |
| Парткод: | B1325911 |
| Деталь: | Bracket:Power Pack:Fix:Up |
| Парткод: | B1325980 |
| Деталь: | Bracket:Power Pack:Fix:Lo |
| Парткод: | B1325981 |
| Деталь: | Harness:Shielded Wire:MB |
| Парткод: | B1325214 |
| Деталь: | Harness:Dc Power Supply:M |
| Парткод: | B1325210 |
| Деталь: | Power Supply Unit:100V |
| Парткод: | AZ250023 |
| Деталь: | Bracket:Power Supply Unit |
| Парткод: | B1325978 |
| Деталь: | Harness:AC Drive:DC Power |
| Парткод: | B1325202 |
| Деталь: | Harness:Leak Breaker:AC D |
| Парткод: | B1325201 |
| Деталь: | Bracket:Leak Breaker:Rear |
| Парткод: | B1325990 |
| Деталь: | Power Supply Cord:Stopper |
| Парткод: | B1325361 |
| Деталь: | Stopper:Power Supply Cord |
| Парткод: | B1325995 |
| Деталь: | Bracket:Power Supply Cord |
| Парткод: | B1325994 |
| Деталь: | Bracket:Leak Breaker |
| Парткод: | B1325985 |
| Деталь: | Bracket:AC Drive Board:We |
| Парткод: | B1325810 |
| Деталь: | Harness:Fusing:100V:C1a ( |
| Парткод: | B1325371 |
| Деталь: | AC Control Board:100V |
| Парткод: | B1325530 |
| Деталь: | Harness:AC Drive Board |
| Парткод: | B1325380 |
| Деталь: | Harness:Bank:Dehumidifier |
| Парткод: | B1325392 |
| Деталь: | Harness:AC:Main:Switch |
| Парткод: | B1325200 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Pan Head Screw:M4x20 |
| Парткод: | 03140200N |
| Деталь: | Breakers: EC2A2 -02 0NVZR (N |
| Парткод: | 11071103 |
| Деталь: | Screw:Spring Washer:M5x12 |
| Парткод: | 09505012N |
| Деталь: | Nylon Clamp - EMT-2N |
| Парткод: | 11050528 |
| Деталь: | Harness Clamp |
| Парткод: | 11050488 |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | Edge Saddle - Les-1010 |
| Парткод: | 11050518 |
| Деталь: | FERRITE CORE |
| Парткод: | 16071461 |
| Деталь: | Operation Panel - Tec |
| Парткод: | B1327205 |
| Деталь: | Keytop:Application:Job (N |
| Парткод: | B1327331 |
| Деталь: | Keytop:Application:Copy ( |
| Парткод: | B1327332 |
| Деталь: | Keytop:Application:Doc (N |
| Парткод: | B1327333 |
| Деталь: | Keytop:Application:Base |
| Парткод: | B1327273 |
| Деталь: | Keytop:Application:Cover |
| Парткод: | B1327274 |
| Деталь: | Decal - Inkjet:Paper |
| Парткод: | B1321562 |
| Деталь: | Lens:Data:In |
| Парткод: | B1327276 |
| Деталь: | DIAL |
| Парткод: | B0271444 |
| Деталь: | Keytop:Counter |
| Парткод: | B1327263 |
| Деталь: | Lens:Keytop:1 |
| Парткод: | B1327275 |
| Деталь: | Keytop:Collar Adjust |
| Парткод: | B1327262 |
| Деталь: | Keytop:Confirm |
| Парткод: | B1327261 |
| Деталь: | Keytop:Block Diagram |
| Парткод: | B1327260 |
| Деталь: | Keytop:Clear: Modes |
| Парткод: | B1327349 |
| Деталь: | Keytop:Preheat |
| Парткод: | B1327258 |
| Деталь: | Keytop:Interrupt |
| Парткод: | B1327257 |
| Деталь: | Keytop:10key |
| Парткод: | B1327252 |
| Деталь: | Keytop:Clear/Stop |
| Парткод: | B1327254 |
| Деталь: | Keytop:Start |
| Парткод: | B1327265 |
| Деталь: | Keytop:Sample Copy |
| Парткод: | B1327253 |
| Деталь: | Keytop:Power Source |
| Парткод: | B1327256 |
| Деталь: | PCB:OP-L |
| Парткод: | B1327310 |
| Деталь: | PCB:OP-R |
| Парткод: | B1327300 |
| Деталь: | Shadeing Plate:Touch Pane |
| Парткод: | B1327286 |
| Деталь: | Insulating Sheet:LCD:Touc |
| Парткод: | B1327297 |
| Деталь: | Touch Panel :HVGA |
| Парткод: | B1805258 |
| Деталь: | Long Spacer - Touch Panel |
| Парткод: | B0271484 |
| Деталь: | Short Spacer - Touch Pane |
| Парткод: | B0271485 |
| Деталь: | LCD: H-VGA: EDMGU95WDF: BK |
| Парткод: | B1325570 |
| Деталь: | Bracket:LCDC:Assy |
| Парткод: | B1327282 |
| Деталь: | Bracket:OP-R |
| Парткод: | B1327290 |
| Деталь: | Clamp:LWS-05S |
| Парткод: | B1327296 |
| Деталь: | PCB:OPU (NA) |
| Парткод: | B1325199 |
| Деталь: | Harness:OP-L:15 |
| Парткод: | B1327314 |
| Деталь: | Harness:OP-L:14 |
| Парткод: | B1327313 |
| Деталь: | Harness - SDG OP-R 13 |
| Парткод: | B1045083 |
| Деталь: | Harness - SDG OP-R 10 |
| Парткод: | B1045084 |
| Деталь: | Bracket:Coupling:Machine |
| Парткод: | B1327287 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52062684 |
| Деталь: | Keytop:Round:Coupling |
| Парткод: | B1327266 |
| Деталь: | Panel Plate Left:NA |
| Парткод: | B1327337 |
| Деталь: | Center Panel Plate |
| Парткод: | B1327291 |
| Деталь: | Panel Plate Right:NA |
| Парткод: | B1327336 |
| Деталь: | Label:Power Switch:NA |
| Парткод: | B1327338 |
| Деталь: | Pin:Operation Panel |
| Парткод: | B1327294 |
| Деталь: | Cover:Cperation Panel |
| Парткод: | B1327250 |
| Деталь: | Bracket:LCT |
| Парткод: | B1325866 |
| Деталь: | Shield:Exhaust |
| Парткод: | B1322438 |
| Деталь: | Seal:Duct:Exhaust:Rear |
| Парткод: | B1322478 |
| Деталь: | Duct:Exhaust:Rear |
| Парткод: | B1322425 |
| Деталь: | Fan Motor:Sirocco |
| Парткод: | AX650041 |
| Деталь: | Stay:Sirocco |
| Парткод: | B1322429 |
| Деталь: | Bracket:Stay:Sirocco |
| Парткод: | B1322430 |
| Деталь: | OZONE FILTER |
| Парткод: | B1322436 |
| Деталь: | DUST FILTER |
| Парткод: | B1322435 |
| Деталь: | Shield:Filter |
| Парткод: | B1322439 |
| Деталь: | Cover:Filter |
| Парткод: | B1322437 |
| Деталь: | Bracket:Finishing Sub-uni |
| Парткод: | B1325867 |
| Деталь: | Harness:AC Drive Board |
| Парткод: | B1325380 |
| Деталь: | Duct:Exit:Exhaust:Exit |
| Парткод: | B1326860 |
| Деталь: | Bracket:Duplex:Exhaust:Fr |
| Парткод: | B1326950 |
| Деталь: | Fan Motor:Upper:Assy |
| Парткод: | B1326954 |
| Деталь: | Fan Motor:Lower:Assy |
| Парткод: | B1326951 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 04513008N |
| Деталь: | Connector - 54679-1615 |
| Парткод: | 11028502 |
| Деталь: | CONNECTOR |
| Парткод: | 11028504 |
| Деталь: | Screw:M3x8 |
| Парткод: | 03530080N |
| Деталь: | Clamp: LWSM- 0306-2M |
| Парткод: | 11050600 |
| Деталь: | Harness Clamp |
| Парткод: | 11050487 |
| Деталь: | Harness Clamp |
| Парткод: | 11050488 |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 11050508 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | DC Solenoid:End Fence:Fro |
| Парткод: | B1327547 |
| Деталь: | Hook - Tension Sprong |
| Парткод: | A2486713 |
| Деталь: | Tension Spring - Long |
| Парткод: | AA060757 |
| Деталь: | End Fence:Front:Adhesion |
| Парткод: | B1327589 |
| Деталь: | Front Support Bracket |
| Парткод: | A2946722 |
| Деталь: | End Fence:Rear |
| Парткод: | B1327556 |
| Деталь: | Rear Support Bracket |
| Парткод: | A2946723 |
| Деталь: | DC Solenoid:End Fence:Rea |
| Парткод: | B1327571 |
| Деталь: | Right Rear Side Plate |
| Парткод: | A2946676 |
| Деталь: | Sensor bracket |
| Парткод: | A2946721 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW020160 |
| Деталь: | Sheet - Photointerrupter |
| Парткод: | A2671820 |
| Деталь: | Wire Ring |
| Парткод: | A2486694 |
| Деталь: | Stay -rightbase |
| Парткод: | B0656870 |
| Деталь: | End Fence Cover Front |
| Парткод: | B0706667 |
| Деталь: | Tension Spring - Short |
| Парткод: | AA060758 |
| Деталь: | Lever:Release:Front |
| Парткод: | B0706683 |
| Деталь: | Sensor bracket |
| Парткод: | A2946720 |
| Деталь: | Wire Pulley - M10 |
| Парткод: | AB032058 |
| Деталь: | Guide - Pulley |
| Парткод: | A2486695 |
| Деталь: | Pulley - M10 |
| Парткод: | AB032719 |
| Деталь: | Cover:Pulley:Drive Were |
| Парткод: | B1327550 |
| Деталь: | Gear - 30Z |
| Парткод: | AB013781 |
| Деталь: | Bushing - 8mm |
| Парткод: | 50530223 |
| Деталь: | Oil Damper Bracket |
| Парткод: | B0656872 |
| Деталь: | OIL DAMPER |
| Парткод: | A2486701 |
| Деталь: | Side Plate:Tandem:Right F |
| Парткод: | B0706668 |
| Деталь: | Front Roller - Slide Rail |
| Парткод: | A2946655 |
| Деталь: | Cushion - Small |
| Парткод: | AA161130 |
| Деталь: | Feeler - Paper Height Sen |
| Парткод: | A2946690 |
| Деталь: | Small Lever |
| Парткод: | B0656864 |
| Деталь: | Roller - Slide Rail |
| Парткод: | AF022105 |
| Деталь: | Spacer - 6mm |
| Парткод: | AA132203 |
| Деталь: | Large Lever |
| Парткод: | B0656862 |
| Деталь: | Side Plate:Tandem:Right F |
| Парткод: | B0706684 |
| Деталь: | Cushion - Large |
| Парткод: | AA161129 |
| Деталь: | SENSOR |
| Парткод: | AW010113 |
| Деталь: | Bracket:Connector:Tandem |
| Парткод: | B1327575 |
| Деталь: | DC Harness - Tandem LCT |
| Парткод: | B0705474 |
| Деталь: | Right Drive Shaft |
| Парткод: | A2486687 |
| Деталь: | Pan Self-tapping Screw:M4 |
| Парткод: | 04340060N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Harness Clamp - ES-0505 |
| Парткод: | 11050328 |
| Деталь: | Pin - M3x20 |
| Парткод: | 06330200G |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Harness Clamp |
| Парткод: | 11050488 |
| Деталь: | Screw - M3X6 |
| Парткод: | 09513006N |
| Деталь: | Pan Head Screw:M3x12 |
| Парткод: | 03130120N |
| Деталь: | Pan Head Screw:M3x8 |
| Парткод: | 03130080N |
| Деталь: | CLAMP |
| Парткод: | 11050199 |
| Деталь: | Cover:Manual Feed:Machine |
| Парткод: | B1322816 |
| Деталь: | Decal - Inkjet:Manual Fee |
| Парткод: | B1321482 |
| Деталь: | Manual Feed Table:Assy |
| Парткод: | B1322810 |
| Деталь: | Side Fence:Auxiliary:Fron |
| Парткод: | B1322863 |
| Деталь: | Side Fence:Auxiliary:Rear |
| Парткод: | B1322866 |
| Деталь: | Side Fence:Front:Assy |
| Парткод: | B1322861 |
| Деталь: | Side Fence:Rear:Assy |
| Парткод: | B1322864 |
| Деталь: | Decal:Paper Set Direction |
| Парткод: | B1322875 |
| Деталь: | Guide:Manual Feed Table |
| Парткод: | B1322868 |
| Деталь: | Rear Rack |
| Парткод: | A2326083 |
| Деталь: | Gear - 16T |
| Парткод: | G0113305 |
| Деталь: | Paper size sensor |
| Парткод: | B1322872 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 04503010N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 04523008N |
| Деталь: | Stay:Machine or Copier:Le |
| Парткод: | B1321115 |
| Деталь: | Cover:Stay:Left |
| Парткод: | B1321222 |
| Деталь: | Slide Rail:Pull Out:Left |
| Парткод: | AA070066 |
| Деталь: | Bracket:Sensor:Entrance |
| Парткод: | B1327101 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW010107 |
| Деталь: | Harness:Exit:Sensor |
| Парткод: | B1325253 |
| Деталь: | Stud:Guide Pin |
| Парткод: | AA143421 |
| Деталь: | Guide Plate:Left Lower:As |
| Парткод: | B1327114 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA063907 |
| Деталь: | Stopper:Pressure |
| Парткод: | B1327038 |
| Деталь: | Slide Rail:Toner Supply:A |
| Парткод: | AA070064 |
| Деталь: | Stay:Slide Rail:Toner Sup |
| Парткод: | B1323486 |
| Деталь: | Guide:Registration:Open A |
| Парткод: | B1322718 |
| Деталь: | Slide Rail:Pull Out:Right |
| Парткод: | AA070067 |
| Деталь: | Stay:Machine Or Copier:Ri |
| Парткод: | B1321004 |
| Деталь: | Lever:Large Capacity Tray |
| Парткод: | B1322717 |
| Деталь: | Shaft:Guide Plate |
| Парткод: | B1322666 |
| Деталь: | Guide Plate:LCT |
| Парткод: | B1322637 |
| Деталь: | Left Gasket - Front Rear |
| Парткод: | B0101289 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG070513 |
| Деталь: | Bushing:6x8x5 |
| Парткод: | AA080265 |
| Деталь: | TENSION SPRING |
| Парткод: | AA060960 |
| Деталь: | Guide Plate:LCT:Open And |
| Парткод: | B1322662 |
| Деталь: | Bracket:Sensor:Large Capa |
| Парткод: | B1322654 |
| Деталь: | Harness:Paper Feed Unit |
| Парткод: | B1325250 |
| Деталь: | Bracket:Cover:LCT |
| Парткод: | B1321008 |
| Деталь: | Bracket:Fix:Manual Feed |
| Парткод: | B1322815 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw:4x12 |
| Парткод: | 04514012N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Screw-m4x6 |
| Парткод: | 03540060N |
| Деталь: | Screw - M3X6 |
| Парткод: | 09513006N |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Clamp:LES-0505 |
| Парткод: | 11050551 |
| Деталь: | Tandem LCT Unit:Right (NA |
| Парткод: | B1327506 |
| Деталь: | Inner Cover:Tandem LCT |
| Парткод: | B1327586 |
| Деталь: | Decal - Caution |
| Парткод: | AA002246 |
| Деталь: | Right Stopper |
| Парткод: | B0656859 |
| Деталь: | Protection -inner Cover |
| Парткод: | B0656875 |
| Деталь: | Decal - Paper Set - Right |
| Парткод: | B0656877 |
| Деталь: | Side Fence:Right Front |
| Парткод: | B1327578 |
| Деталь: | Plate:Paper:Assy |
| Парткод: | A2946734 |
| Деталь: | Base:Tandem LCT:Right |
| Парткод: | B1327543 |
| Деталь: | Friction pad |
| Парткод: | 52012858 |
| Деталь: | Sensor bracket |
| Парткод: | A2946706 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW020160 |
| Деталь: | Misfeed Removal Guide |
| Парткод: | A1766695 |
| Деталь: | Seal - 4x10x70 |
| Парткод: | AA153063 |
| Деталь: | Decal - Paper Level |
| Парткод: | AA002010 |
| Деталь: | Side Fence:Tandem LCT:Rig |
| Парткод: | B1327576 |
| Деталь: | Side plate |
| Парткод: | A2946666 |
| Деталь: | Decal - Right Paper Set |
| Парткод: | A0966677 |
| Деталь: | Interlock Guide - Tandem |
| Парткод: | B0656672 |
| Деталь: | Screw: Pol ished Round: M4x8 |
| Парткод: | 09514008N |
| Деталь: | Philips Pan Head Screw - |
| Парткод: | 03140060N |
| Деталь: | Tapping Screw:M4x8 |
| Парткод: | 04524008N |
| Деталь: | Pan Self-tapping Screw:M4 |
| Парткод: | 04340060N |
| Деталь: | Screw: Pol ished Round: M4x6 |
| Парткод: | 09514006N |
| Деталь: | CLAMP |
| Парткод: | 11050230 |
| Деталь: | CLAMP |
| Парткод: | 11050199 |
| Деталь: | Lens Unit |
| Парткод: | B1321731 |
| Деталь: | INTERFACE CABLE |
| Парткод: | B1325369 |
| Деталь: | COVER |
| Парткод: | B1321674 |
| Деталь: | Bracket:Open And Close:Le |
| Парткод: | B1321871 |
| Деталь: | Rubber Bushing |
| Парткод: | A2571884 |
| Деталь: | Bracket:Positioning:Left |
| Парткод: | B1321877 |
| Деталь: | Cushion - Motor |
| Парткод: | AA161104 |
| Деталь: | Spring Plate:Earth:Scanne |
| Парткод: | B1321897 |
| Деталь: | Bracket:Positioning:Right |
| Парткод: | B1321874 |
| Деталь: | Lever:Scanner Unit:Open A |
| Парткод: | B1321886 |
| Деталь: | Fan Motor:Mm60 |
| Парткод: | AX640151 |
| Деталь: | Bracket:Open And Close:Ri |
| Парткод: | B1321872 |
| Деталь: | Ground Wire:Scanner |
| Парткод: | B1321896 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW020145 |
| Деталь: | Sheet - Photointerrupter |
| Парткод: | A2671820 |
| Деталь: | Ground Plate:Scanner:Rear |
| Парткод: | B1321112 |
| Деталь: | Plate:Rod |
| Парткод: | B1321889 |
| Деталь: | Rod:Open And Close:Scanne |
| Парткод: | B1321888 |
| Деталь: | Seal:Inner Cover |
| Парткод: | B1321678 |
| Деталь: | Cover:Siob |
| Парткод: | B1321677 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw:Round Point |
| Парткод: | 8025291 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Tapping Screw:M4x25 |
| Парткод: | 04514025N |
| Деталь: | Screw:Spring Washer:M4x8 |
| Парткод: | 09504008N |
| Деталь: | Screw:M4x8 |
| Парткод: | 03540080N |
| Деталь: | Bushing - 4x5 |
| Парткод: | 07074050N |
| Деталь: | Harness Clamp |
| Парткод: | 11050487 |
| Деталь: | Toner Supply Unit:Assy |
| Парткод: | B2003211 |
| Деталь: | STAY |
| Парткод: | B1323428 |
| Деталь: | Spring Plate:Stand |
| Парткод: | B1323240 |
| Деталь: | Lever:Stand |
| Парткод: | B1323239 |
| Деталь: | Shaft:Lever:Stand |
| Парткод: | B1323216 |
| Деталь: | Spring Plate:Lever:Stand |
| Парткод: | B1323242 |
| Деталь: | Guide Plate:Lever:Stand |
| Парткод: | B1323241 |
| Деталь: | Inner Cover:Left |
| Парткод: | B1323236 |
| Деталь: | Stand:Left |
| Парткод: | B1323237 |
| Деталь: | Guide:Stand |
| Парткод: | B1323238 |
| Деталь: | Guide: Arm: Stopper: Holder |
| Парткод: | B1323323 |
| Деталь: | Arm:Stopper:Holder:Color |
| Парткод: | B1323322 |
| Деталь: | Bracket:Stopper:Holder:Le |
| Парткод: | B1323316 |
| Деталь: | Bracket:Stopper:Holder:Ri |
| Парткод: | B1323314 |
| Деталь: | Holder:Toner Cartridge:Co |
| Парткод: | B1323287 |
| Деталь: | Cover:Black |
| Парткод: | B1323232 |
| Деталь: | Inner Cover:Right |
| Парткод: | B1323235 |
| Деталь: | Cover: Lower: Holder: Y |
| Парткод: | B2003254 |
| Деталь: | Cover: Lower: Holder: M |
| Парткод: | B2003252 |
| Деталь: | Cover: Lower: Holder: C |
| Парткод: | B2003253 |
| Деталь: | Cover:Color |
| Парткод: | B1323233 |
| Деталь: | Sheet:Cover:Holder |
| Парткод: | B1323234 |
| Деталь: | Arm:Stopper:Holder:Black |
| Парткод: | B1323321 |
| Деталь: | Decal:Lever:Toner Supply: |
| Парткод: | B1323330 |
| Деталь: | Holder:Toner Cartridge:Bl |
| Парткод: | B1323286 |
| Деталь: | Cover:Lower:Holder:Black |
| Парткод: | B2003251 |
| Деталь: | SHEET |
| Парткод: | B1323245 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Screw:M4x8 |
| Парткод: | 03540080N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Decal:Lever:Toner Supply: |
| Парткод: | B1323331 |
| Деталь: | Decal:Lever:Toner Supply: |
| Парткод: | B1323332 |
| Деталь: | Decal:Lever:Toner Supply: |
| Парткод: | B1323333 |
| Деталь: | Guide Plate:Left Upper:As |
| Парткод: | B1327115 |
| Деталь: | Roller:MM 14 |
| Парткод: | B1327033 |
| Деталь: | Grip:Guide Plate:Left |
| Парткод: | B1327015 |
| Деталь: | Guide Plat:Left Lower:Ass |
| Парткод: | B1327110 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Spring:Guide Plate:Open A |
| Парткод: | AA063909 |
| Деталь: | Gate Pawl:Reverse |
| Парткод: | B1327054 |
| Деталь: | Guide Plate:Middle:Transp |
| Парткод: | B1327004 |
| Деталь: | Guide Plate:Middle:Left |
| Парткод: | B1327064 |
| Деталь: | Arm:Pressure |
| Парткод: | B1327045 |
| Деталь: | Shaft:Release:Guide Plate |
| Парткод: | B1327029 |
| Деталь: | Plate:Transport Roller |
| Парткод: | B1327169 |
| Деталь: | Lever:Release |
| Парткод: | B1327098 |
| Деталь: | Guide Plate:Middle:Right |
| Парткод: | B1327017 |
| Деталь: | Roller:Middle |
| Парткод: | B1327031 |
| Деталь: | Spring Plate:Middle |
| Парткод: | B1327020 |
| Деталь: | Stay:Supporting Plate |
| Парткод: | B1327160 |
| Деталь: | Guide:Entrance:Right Rear |
| Парткод: | B1327103 |
| Деталь: | Stay:Shaft:Assy |
| Парткод: | B1327097 |
| Деталь: | Lever:Release:Guide Plate |
| Парткод: | B1327046 |
| Деталь: | Side Plate:Rear:Assy |
| Парткод: | B1327078 |
| Деталь: | DC Solenoid:Bracket:Assy |
| Парткод: | B1327148 |
| Деталь: | TENSION SPRING |
| Парткод: | AA062330 |
| Деталь: | Side Plate:Front:Assy |
| Парткод: | B1327076 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 04503006N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 03530060N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Ball Bearing - 6x10x3 |
| Парткод: | 7413706 |
| Деталь: | Screw:M3x8 |
| Парткод: | 03530080N |
| Деталь: | Shield:Joint:PCU |
| Парткод: | B1326578 |
| Деталь: | Case:Toner Outlet Sub-uni |
| Парткод: | B1326519 |
| Деталь: | Case:Toner Outlet Sub-uni |
| Парткод: | B1326518 |
| Деталь: | Toner Catchpan:Tank:Entra |
| Парткод: | B1326539 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW500023 |
| Деталь: | Transport Screw: Upper:Ass |
| Парткод: | B1326520 |
| Деталь: | Harness:Toner Recycling S |
| Парткод: | B1325393 |
| Деталь: | Photointerruptor:Feeler:S |
| Парткод: | AW020147 |
| Деталь: | Base:Toner Outlet Sub-uni |
| Парткод: | B1326512 |
| Деталь: | Bracket:Toner Outlet Sub- |
| Парткод: | B1326514 |
| Деталь: | TENSION SPRING |
| Парткод: | B1326542 |
| Деталь: | Gear:31/44Z |
| Парткод: | AB011029 |
| Деталь: | Shaft:Toner Outlet Sub-un |
| Парткод: | B1326527 |
| Деталь: | Shaft:Drive:Long:Assy |
| Парткод: | B1326548 |
| Деталь: | Gear:18Z |
| Парткод: | AB013299 |
| Деталь: | Brushless motor |
| Парткод: | AX060302 |
| Деталь: | Cover:DC Motor |
| Парткод: | B1326537 |
| Деталь: | Gear:14/30Z |
| Парткод: | AB011248 |
| Деталь: | Gear:32Z |
| Парткод: | AB011247 |
| Деталь: | Bushing:Transport Screw |
| Парткод: | B1326536 |
| Деталь: | Toner Collection Gear |
| Парткод: | B0653587 |
| Деталь: | Spacer - M6 |
| Парткод: | AA132208 |
| Деталь: | SPRING |
| Парткод: | B0653561 |
| Деталь: | Guide:Spring:Discharge Us |
| Парткод: | B1326526 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 04513008N |
| Деталь: | Screw:M3x8 |
| Парткод: | 03530080N |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | Harness Clamp |
| Парткод: | 11050488 |
| Деталь: | Clamp: LWSM-0306-2M |
| Парткод: | 11050600 |
| Деталь: | INTERFACE HARNESS |
| Парткод: | B4775751 |
| Деталь: | Harness:Motor:Exit |
| Парткод: | B6525421 |
| Деталь: | Harness:Solenoid:Reverse |
| Парткод: | B6525426 |
| Деталь: | Harness:Paper Size Sensor |
| Парткод: | B6525406 |
| Деталь: | Harness:Original Sensor |
| Парткод: | B6525401 |
| Деталь: | Harness:Motor:Pick Up |
| Парткод: | B6525441 |
| Деталь: | Paper Feed Motor Harness |
| Парткод: | B4775691 |
| Деталь: | PCB:Main Control |
| Парткод: | B6525503 |
| Деталь: | Stepper Motor:Base:Rise:A |
| Парткод: | B6522911 |
| Деталь: | Bracket:Motor:Base:Assy |
| Парткод: | B6522343 |
| Деталь: | Timing Belt :B40S2M158 |
| Парткод: | B6522347 |
| Деталь: | Gear - Z20/Z47 |
| Парткод: | A8062287 |
| Деталь: | Gear - Z20/Z47 |
| Парткод: | A8062285 |
| Деталь: | Spacer - 8x20x1 |
| Парткод: | AA132152 |
| Деталь: | Timing Pulley - T30/Z20 S |
| Парткод: | A8062161 |
| Деталь: | Gear - Z20/Z47 |
| Парткод: | A8062283 |
| Деталь: | Stepper Motor:Exit:Assy |
| Парткод: | B6524722 |
| Деталь: | Timing Belt :B40S2M138 |
| Парткод: | B6524728 |
| Деталь: | Scanning Motor- DC 7.4W |
| Парткод: | B4773721 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | B6523211 |
| Деталь: | Tension Spring:Tension:Tr |
| Парткод: | AA060991 |
| Деталь: | Guide Plate:Stepper Motor |
| Парткод: | B6523215 |
| Деталь: | Timing Belt:B60S2M280 |
| Парткод: | B6521721 |
| Деталь: | Timing Belt:B40S2M230 |
| Парткод: | B6524153 |
| Деталь: | Bracket:Solenoid:Reverse: |
| Парткод: | B6524223 |
| Деталь: | Damper - Junction Gate So |
| Парткод: | A6972102 |
| Деталь: | DC Solenoid:Assy |
| Парткод: | B6524222 |
| Деталь: | Bracket: Shaft: Scanning:As |
| Парткод: | B6521781 |
| Деталь: | PULLEY |
| Парткод: | B4773217 |
| Деталь: | Screw:Safety |
| Парткод: | AA143791 |
| Деталь: | PULLEY |
| Парткод: | B4773175 |
| Деталь: | TENSION SPRING |
| Парткод: | B6523174 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52152621 |
| Деталь: | Belt Tensioner:Assy |
| Парткод: | B6523231 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 04503008N |
| Деталь: | Screw-m3x5 |
| Парткод: | 03530050N |
| Деталь: | Tapping Screw - 4x6 |
| Парткод: | 04514006N |
| Деталь: | Screw - M3X4 |
| Парткод: | 03530040N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Harness Clamp |
| Парткод: | 11050487 |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Guide Plate - Upper Heat |
| Парткод: | A2486103 |
| Деталь: | Heat Sink:Heater:Upper:Fi |
| Парткод: | B0706293 |
| Деталь: | Supporting Plate:Stay |
| Парткод: | B1326669 |
| Деталь: | Slide Rail:Tandem LCT |
| Парткод: | AA070072 |
| Деталь: | Slidebracket |
| Парткод: | B0656774 |
| Деталь: | Stay:Tandem LCT:Assy |
| Парткод: | B1326696 |
| Деталь: | Rail:Tandem LCT:Left:Ass |
| Парткод: | B1327590 |
| Деталь: | Left Rail Bracket |
| Парткод: | B1326742 |
| Деталь: | Lock Arm - Tandem Tray |
| Парткод: | B0656135 |
| Деталь: | SPRING |
| Парткод: | AA060761 |
| Деталь: | Side Plate:Front:Paper Ba |
| Парткод: | B1326689 |
| Деталь: | Rail:Paper Tray:Assy |
| Парткод: | B1327591 |
| Деталь: | Seal - Misfeed Removal |
| Парткод: | AA150406 |
| Деталь: | Bracket:Holder: Assy |
| Парткод: | B1326630 |
| Деталь: | Heater:115V:18W:Upper |
| Парткод: | AX400176 |
| Деталь: | Heater:240V:18W:Upper |
| Парткод: | AX400178 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | DC Motor:MM56:15W |
| Парткод: | AX060281 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW020145 |
| Деталь: | Bracket:Sensor |
| Парткод: | B1321307 |
| Деталь: | Bracket:Brushless Motor:P |
| Парткод: | B1321291 |
| Деталь: | Gear:72Z |
| Парткод: | AB010136 |
| Деталь: | Gear:Pulley:72Z/20T |
| Парткод: | AB017684 |
| Деталь: | Gear:108Z |
| Парткод: | AB010137 |
| Деталь: | Bracket:Plate |
| Парткод: | B1321297 |
| Деталь: | Shaft: Drive: Cleaning |
| Парткод: | B1321300 |
| Деталь: | Shaft:Drive:Transfer |
| Парткод: | B1321295 |
| Деталь: | Stepped Screw - Guide Pla |
| Парткод: | 52164198 |
| Деталь: | Receptacle:Connector:6p |
| Парткод: | B1322325 |
| Деталь: | Receptacle:Development Vi |
| Парткод: | B1323186 |
| Деталь: | Harness:T:Sensor:Drawer |
| Парткод: | B1325272 |
| Деталь: | Harness:Development:BM |
| Парткод: | B1325340 |
| Деталь: | Harness: Development: CY |
| Парткод: | B1325342 |
| Деталь: | Bracket:Drawer:Paper Feed |
| Парткод: | B1321020 |
| Деталь: | Screw: Spring: Drawer |
| Парткод: | AA143794 |
| Деталь: | Spring Connector:9.8n |
| Парткод: | AA063670 |
| Деталь: | Duct:Joint:Fusing |
| Парткод: | B1322428 |
| Деталь: | Connector Guide Pin |
| Парткод: | AA143797 |
| Деталь: | Harness: Duplex: DRB: Drawer |
| Парткод: | B1325260 |
| Деталь: | Receptacle:Assy |
| Парткод: | B1323650 |
| Деталь: | Bracket:Spring Plate:Ass |
| Парткод: | B1327107 |
| Деталь: | Duct:Connecting:Pull Out: |
| Парткод: | B1322461 |
| Деталь: | Harness:Sensor:Drawer:Bla |
| Парткод: | B1325270 |
| Деталь: | Harness:Sensor:Drawer:MCY |
| Парткод: | B1325271 |
| Деталь: | Duct: Joint: Fusing: Rear |
| Парткод: | B1322453 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Screw - M3X6 |
| Парткод: | 03603006N |
| Деталь: | Ball Bearing - 8x16x5mm |
| Парткод: | 7403808 |
| Деталь: | Connector:Drawer:1612257- |
| Парткод: | 11029430 |
| Деталь: | Connector:55949-2619 |
| Парткод: | 11029784 |
| Деталь: | Power Pack:T1/T2 |
| Парткод: | AZ320138 |
| Деталь: | Insulating Sheet:Power Pa |
| Парткод: | B1326145 |
| Деталь: | Guard:Right |
| Парткод: | B1326170 |
| Деталь: | Guard:Left |
| Парткод: | B1326171 |
| Деталь: | Guard:Rear |
| Парткод: | B1326172 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW020145 |
| Деталь: | Spring Plate:Cam |
| Парткод: | B1326124 |
| Деталь: | Stopper:On-Off |
| Парткод: | B1326157 |
| Деталь: | DUCT |
| Парткод: | B1326121 |
| Деталь: | Harness:Density Sensor |
| Парткод: | B1325237 |
| Деталь: | Belt Sensor |
| Парткод: | B1326119 |
| Деталь: | Bracket:Belt Sensor |
| Парткод: | B1326122 |
| Деталь: | Stand |
| Парткод: | B1326156 |
| Деталь: | Harness:Intermediate Tran |
| Парткод: | B1325376 |
| Деталь: | Harness:Intermediate Tran |
| Парткод: | B1325377 |
| Деталь: | Harness:Transfer Unit:Bel |
| Парткод: | B1325355 |
| Деталь: | Plate:Bracke |
| Парткод: | B1326165 |
| Деталь: | Grip:Application |
| Парткод: | B7125605 |
| Деталь: | Screw - M3X6 |
| Парткод: | 03603006N |
| Деталь: | Card Spacer - 9.4mm |
| Парткод: | 11050410 |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | CLAMP |
| Парткод: | 11050534 |
| Деталь: | Connector:51405-3919 |
| Парткод: | 11029781 |
| Деталь: | Connector:51405-1819 |
| Парткод: | 11029782 |
| Деталь: | Cover Oil Application Uni |
| Парткод: | B1324176 |
| Деталь: | Guide Plate:Fusing Exit:U |
| Парткод: | B1324174 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52062684 |
| Деталь: | Grip:Oil Application Unit |
| Парткод: | B1324168 |
| Деталь: | Lever:Oil Application Uni |
| Парткод: | B1324165 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA082138 |
| Деталь: | Bracket:Oil Application U |
| Парткод: | B1324160 |
| Деталь: | Shaft:Oil Application Uni |
| Парткод: | B1324163 |
| Деталь: | TORSION SPRING:LEVER |
| Парткод: | B1324197 |
| Деталь: | Lever:Oil Application Uni |
| Парткод: | B1324164 |
| Деталь: | Compression Spring - 2.5n |
| Парткод: | B1324191 |
| Деталь: | Bushing:Cleaning Roller |
| Парткод: | AE031057 |
| Деталь: | Oil Supply Roller |
| Парткод: | AE040068 |
| Деталь: | Hot Roller Cleaning Rolle |
| Парткод: | AE042051 |
| Деталь: | Housing : Thermostat |
| Парткод: | B1324148 |
| Деталь: | Bracket:Thermistor:Hot Ro |
| Парткод: | B1324146 |
| Деталь: | Housing : Thermostat |
| Парткод: | B1324153 |
| Деталь: | Bracket : Torsion Spring :Pe |
| Парткод: | B1324127 |
| Деталь: | Torsion Spring:Oil Applic |
| Парткод: | B1324195 |
| Деталь: | Stripper Pawls:Assy |
| Парткод: | B1324258 |
| Деталь: | Stripper Pawl Stay |
| Парткод: | B1324256 |
| Деталь: | Torsion Spring:Lever:Rear |
| Парткод: | B1324190 |
| Деталь: | Spring Plate:Oil Applicat |
| Парткод: | B1324269 |
| Деталь: | Torsion Spring:Guide Plat |
| Парткод: | B1324198 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA082101 |
| Деталь: | Screw - M3x8 |
| Парткод: | 09543008N |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 07200030E |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 03530060N |
| Деталь: | Rail - Side Fence |
| Парткод: | G5644151 |
| Деталь: | Table Side Fence |
| Парткод: | B4772272 |
| Деталь: | Side Fence Pad |
| Парткод: | A3764599 |
| Деталь: | Original Sensor Feeler St |
| Парткод: | B4772286 |
| Деталь: | Original Sensor Feeler |
| Парткод: | A8061351 |
| Деталь: | Snap Ring |
| Парткод: | 52062686 |
| Деталь: | Base:Original Table:Assy |
| Парткод: | B6522351 |
| Деталь: | Decal:Base:Original |
| Парткод: | B6522354 |
| Деталь: | Harness:Original Sensor |
| Парткод: | B6525451 |
| Деталь: | Photointerruptor |
| Парткод: | AW020141 |
| Деталь: | Original Sensor Bracket |
| Парткод: | B4772281 |
| Деталь: | Photo Refiection Sensor:O |
| Парткод: | AW010112 |
| Деталь: | Shaft:Rise:Base |
| Парткод: | B6522333 |
| Деталь: | Bushing - 8mm |
| Парткод: | A6281225 |
| Деталь: | Lever:Rise:Base |
| Парткод: | B6522334 |
| Деталь: | Bracket:Lever:Rise:Base |
| Парткод: | B6522335 |
| Деталь: | Shaft:Base:Rear:Assy |
| Парткод: | B6522363 |
| Деталь: | Arm:Roller:Reverse:Upper |
| Парткод: | B6522403 |
| Деталь: | Pressure Roller - Reverse |
| Парткод: | B3513752 |
| Деталь: | Compression Spring:3.1n |
| Парткод: | B6522404 |
| Деталь: | Bushing - 8mm |
| Парткод: | 50530223 |
| Деталь: | Ground Plate:Shaft:Base |
| Парткод: | B6522323 |
| Деталь: | Bushing:Original Table |
| Парткод: | B6522375 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Discharge Brush |
| Парткод: | A8593225 |
| Деталь: | Stopper:Original Table |
| Парткод: | B6522392 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B6522393 |
| Деталь: | Guide Plate:Reverse:Upper |
| Парткод: | B6522322 |
| Деталь: | Snap Ring |
| Парткод: | C1012360 |
| Деталь: | Gear - Z47 |
| Парткод: | A8062281 |
| Деталь: | Shaft:Cleaner |
| Парткод: | AA143789 |
| Деталь: | Original Table:Face Front |
| Парткод: | B6522372 |
| Деталь: | Original Table:Behind |
| Парткод: | B6522383 |
| Деталь: | Harness:Sensor:Original T |
| Парткод: | B6525436 |
| Деталь: | Duplex Turn Roller |
| Парткод: | AF021075 |
| Деталь: | Driven Transport Roller |
| Парткод: | AF021077 |
| Деталь: | Drive Inverter Roller |
| Парткод: | AF021076 |
| Деталь: | Left Drive Roller |
| Парткод: | AF021078 |
| Деталь: | Jogger Guide Rod |
| Парткод: | B0654694 |
| Деталь: | Right Drive Roller |
| Парткод: | AF021079 |
| Деталь: | Timing Pulley - 24Z |
| Парткод: | AB030583 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA082118 |
| Деталь: | Timing Belt:40S2M278G |
| Парткод: | AA043310 |
| Деталь: | Timing Belt:40S2M302G |
| Парткод: | AA043311 |
| Деталь: | Gear:45Z |
| Парткод: | AB011497 |
| Деталь: | PULLEY |
| Парткод: | AB017614 |
| Деталь: | Gear:22Z |
| Парткод: | AB011498 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Gear - 32Z |
| Парткод: | AB011496 |
| Деталь: | Pulley - 29Z |
| Парткод: | AB030731 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Ball Bearing - 8x16x5mm |
| Парткод: | 7413808 |
| Деталь: | Filter:Duct:Intermediate |
| Парткод: | B1322466 |
| Деталь: | Duct:Intermediate Transfe |
| Парткод: | B1322454 |
| Деталь: | Fan Motor:MM40:15mm |
| Парткод: | AX640149 |
| Деталь: | Harness:Sensor:Fan Motor |
| Парткод: | B1325232 |
| Деталь: | Plate:Lever |
| Парткод: | B1322365 |
| Деталь: | Lever:Drum Stay:Left |
| Парткод: | B1322366 |
| Деталь: | Side Plate Lever |
| Парткод: | A2573441 |
| Деталь: | Drum Stay |
| Парткод: | B1322318 |
| Деталь: | Heat Insulation:Drum Stay |
| Парткод: | B1322388 |
| Деталь: | Seal: Drum Stay: Lower |
| Парткод: | B1322417 |
| Деталь: | Duct:Drum Stay:PCU |
| Парткод: | B1322423 |
| Деталь: | Inner Cover:Drum Stay |
| Парткод: | B1322399 |
| Деталь: | Shield:Duct:Intermediate |
| Парткод: | B1322450 |
| Деталь: | Duct:Drum Stay |
| Парткод: | B1322442 |
| Деталь: | Decal Grip |
| Парткод: | B0653699 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Screw:M4x8 |
| Парткод: | 03540080N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Tapping Screw:M3x20 |
| Парткод: | 04503020N |
| Деталь: | Electric Potential Sensor |
| Парткод: | B1322344 |
| Деталь: | Joint PCU |
| Парткод: | B1323600 |
| Деталь: | Positioning Plate:Cleanin |
| Парткод: | B1322335 |
| Деталь: | Drum Stay:Rear |
| Парткод: | B1323607 |
| Деталь: | OPC Drum |
| Парткод: | B1329510 |
| Деталь: | Bushing:Brush Roller |
| Парткод: | B1323655 |
| Деталь: | Bushing - 6x8x5 |
| Парткод: | AA082106 |
| Деталь: | Drum Cleaning Brush Assy |
| Парткод: | B1323555 |
| Деталь: | Drum Stay:Front:Ass/y |
| Парткод: | B1323601 |
| Деталь: | Whole PCU-K |
| Парткод: | B1329830 |
| Деталь: | Whole PCU-M |
| Парткод: | B1329831 |
| Деталь: | Whole PCU-C |
| Парткод: | B1329832 |
| Деталь: | Whole PCU-Y |
| Парткод: | B1329833 |
| Деталь: | Drum Cleaning Blade |
| Парткод: | B1323560 |
| Деталь: | Drum Charge Roller Assy |
| Парткод: | B1322270 |
| Деталь: | Temperature & Humidity Se |
| Парткод: | AW140012 |
| Деталь: | Stay:Temperature & Humidi |
| Парткод: | B1322380 |
| Деталь: | Drum Lubricant Bar |
| Парткод: | B1323573 |
| Деталь: | Ground Plate:Brush Roller |
| Парткод: | B1323656 |
| Деталь: | Cleaning Brush Seal Rear |
| Парткод: | B1323653 |
| Деталь: | Cleaning Brush Seal Front |
| Парткод: | B1323654 |
| Деталь: | Discharge Lamp:LED Array |
| Парткод: | B1322269 |
| Деталь: | Stay:Toner Catch |
| Парткод: | B1323070 |
| Деталь: | Gear - 30Z |
| Парткод: | B1323596 |
| Деталь: | Transport Screw |
| Парткод: | B1323580 |
| Деталь: | Lubricant Bar Weight |
| Парткод: | B1323574 |
| Деталь: | Cap:Toner Supply:Upper |
| Парткод: | B1323179 |
| Деталь: | Screw - M3X6 |
| Парткод: | 03603006P |
| Деталь: | Developer Cartridge Black |
| Парткод: | B2009640 |
| Деталь: | Developer Cartridge Cyan |
| Парткод: | B2009660 |
| Деталь: | Developer Cartridge Magen |
| Парткод: | B2009670 |
| Деталь: | Developer Cartridge Yello |
| Парткод: | B2009680 |
| Деталь: | Entrance Scanning Guide |
| Парткод: | B4772581 |
| Деталь: | SPRING |
| Парткод: | B4774115 |
| Деталь: | Driven Entrance Scanning |
| Парткод: | B4772577 |
| Деталь: | Bushing- 4x8x4.5mm |
| Парткод: | 53241658 |
| Деталь: | SPACER |
| Парткод: | A3742181 |
| Деталь: | Entrance Scanning Roller |
| Парткод: | B4772575 |
| Деталь: | Arm:Roller:Scanning:Entra |
| Парткод: | B4772574 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A4221063 |
| Деталь: | Entrance Scanning Base |
| Парткод: | B4772561 |
| Деталь: | Guide Bracket |
| Парткод: | B4772145 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW010117 |
| Деталь: | Harness:Registration Sens |
| Парткод: | B6525431 |
| Деталь: | Registration Sensor Brack |
| Парткод: | B4772665 |
| Деталь: | Guide Plate:Entrance :Uppe |
| Парткод: | B6523251 |
| Деталь: | Discharge Brush |
| Парткод: | A8593225 |
| Деталь: | Drive Relay Roller |
| Парткод: | B4772121 |
| Деталь: | Roller: Scanning: Entrance: |
| Парткод: | B6522411 |
| Деталь: | Roller:Pull Out:Drive |
| Парткод: | B6522112 |
| Деталь: | Roller:Scanning:Exit:Driv |
| Парткод: | B6522421 |
| Деталь: | Timing Belt :B80S3M417 |
| Парткод: | B6521783 |
| Деталь: | Timing Belt :B60S2M172 |
| Парткод: | B6523135 |
| Деталь: | Paper Feed Cover Bracket |
| Парткод: | B4771775 |
| Деталь: | Bushing - 16x18x5 |
| Парткод: | AA082141 |
| Деталь: | Screw:Safety |
| Парткод: | AA143791 |
| Деталь: | Timing Belt:B40S2M230 |
| Парткод: | B6524153 |
| Деталь: | Timing Pulley - T28 S2M |
| Парткод: | A8062111 |
| Деталь: | Harness:Manual Feed:Stepp |
| Парткод: | B1325218 |
| Деталь: | Harness:DRB:IOB:Power Sou |
| Парткод: | B1325213 |
| Деталь: | Harness:Large Capacity Tr |
| Парткод: | B1325216 |
| Деталь: | Harness:Power Supply Unit |
| Парткод: | B1325211 |
| Деталь: | Harness:DRB:Safety Switch |
| Парткод: | B1325383 |
| Деталь: | Harness:Duplex:DRB:Drawer |
| Парткод: | B1325260 |
| Деталь: | PCB DRB |
| Парткод: | B1325438 |
| Деталь: | PCB:DMB |
| Парткод: | B1325425 |
| Деталь: | Harness: Drum: Motor: KM |
| Парткод: | B1325267 |
| Деталь: | PCB:TMB |
| Парткод: | B1325476 |
| Деталь: | Bracket:Power Pack |
| Парткод: | B1325979 |
| Деталь: | Harness:Bank:Front:3way |
| Парткод: | B1325395 |
| Деталь: | Harness:Bank:Rear:3way |
| Парткод: | B1325396 |
| Деталь: | Harness:IOB:PP1:PFC |
| Парткод: | B1325381 |
| Деталь: | PCB:pFC |
| Парткод: | B1325461 |
| Деталь: | Harness :Main |
| Парткод: | B1325350 |
| Деталь: | Power Pack:C |
| Парткод: | AZ320136 |
| Деталь: | Bracket:DRV |
| Парткод: | B1325862 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Screw - M3X6 |
| Парткод: | 03603006N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Harness Clamp - LWS 1316 |
| Парткод: | 11050489 |
| Деталь: | Card Spacer- 6.4mm |
| Парткод: | 11050409 |
| Деталь: | Harness Clamp |
| Парткод: | 11050488 |
| Деталь: | Clamp - LES-1017 |
| Парткод: | 11050521 |
| Деталь: | Development Unit |
| Парткод: | B2003080 |
| Деталь: | Gear:Development Roller |
| Парткод: | B1323120 |
| Деталь: | Gear - 21Z |
| Парткод: | B1323118 |
| Деталь: | Gear - 19/27Z |
| Парткод: | B1323123 |
| Деталь: | Gear - 27Z |
| Парткод: | B1323124 |
| Деталь: | DENSITY SENSOR |
| Парткод: | B1323199 |
| Деталь: | Cover:Gear:Assy |
| Парткод: | B1323155 |
| Деталь: | Case:Developer:Upper |
| Парткод: | B1323086 |
| Деталь: | Drum Stay:PCU:Rear |
| Парткод: | B1322299 |
| Деталь: | Drum Stay:PCU:Front |
| Парткод: | B1322298 |
| Деталь: | Adjusting Pin:Magnetic Ro |
| Парткод: | B1323159 |
| Деталь: | Cap:Toner Supply:Upper |
| Парткод: | B1323179 |
| Деталь: | Rubber Band |
| Парткод: | B2003179 |
| Деталь: | Hexagonal Bolt:W/Washer:M |
| Парткод: | 8046123 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 04523008N |
| Деталь: | Screw - M3X6 |
| Парткод: | 03603006N |
| Деталь: | Supporting Plate:Side Pla |
| Парткод: | B1323217 |
| Деталь: | Brushless Motor:Drive:Pap |
| Парткод: | GX060015 |
| Деталь: | Bracket: Fix: Right |
| Парткод: | B1323218 |
| Деталь: | Filter:Duct |
| Парткод: | B1322475 |
| Деталь: | Cover:Lower:Black |
| Парткод: | B1323229 |
| Деталь: | Gear:75Z |
| Парткод: | B1323224 |
| Деталь: | Shaft:Drive |
| Парткод: | B1323222 |
| Деталь: | Gear:21/32Z |
| Парткод: | B1323223 |
| Деталь: | Guide:Shaft:Drive |
| Парткод: | AA082139 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52152621 |
| Деталь: | Cover:Drawer |
| Парткод: | B1323435 |
| Деталь: | Bracket:Drawer |
| Парткод: | B1323434 |
| Деталь: | Bracket:PCB |
| Парткод: | B1323431 |
| Деталь: | PCB:CNB |
| Парткод: | B1325440 |
| Деталь: | Harness:CNB:Left |
| Парткод: | B1325228 |
| Деталь: | Harness:Toner Hopper:Uni: |
| Парткод: | B1325227 |
| Деталь: | SHEET |
| Парткод: | B1323245 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw:3X6 |
| Парткод: | 04543006Q |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Ball Bearing - 8x16x5 |
| Парткод: | 7423808 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | Harness Clamp |
| Парткод: | 11050487 |
| Деталь: | Screw:M4x8 |
| Парткод: | 03540080N |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | Harness Clamp |
| Парткод: | 11050488 |
| Деталь: | Card Spacer- 6.4mm |
| Парткод: | 11050409 |
| Деталь: | Connector:51405-3919 |
| Парткод: | 11029781 |
| Деталь: | Inner Cover:Duplex Unit:A |
| Парткод: | B1324525 |
| Деталь: | Decal:Warning (high Tempe |
| Парткод: | B1324797 |
| Деталь: | Duplex Unit:Ass/y |
| Парткод: | B1324501 |
| Деталь: | Grip:Release:Duplex Unit |
| Парткод: | B1324674 |
| Деталь: | Release Lever Shaft |
| Парткод: | B0654673 |
| Деталь: | Arm:Lock:Duplex |
| Парткод: | B1324671 |
| Деталь: | Duplex Release Bracket |
| Парткод: | B0654675 |
| Деталь: | SPRING |
| Парткод: | AA062320 |
| Деталь: | Release Lever Bracket |
| Парткод: | B0654672 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Stay:Duplex Unit:Upper |
| Парткод: | B1324987 |
| Деталь: | Guide Plate:Jogger:Upper |
| Парткод: | B1324874 |
| Деталь: | Guide Plate:Duplex:Exit |
| Парткод: | B1324869 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA143811 |
| Деталь: | Table:Duplex:Right |
| Парткод: | B1324725 |
| Деталь: | Bracket:Sensor:Right |
| Парткод: | B1324727 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW020149 |
| Деталь: | Harness:Sensor:Duplex:3p |
| Парткод: | B1325263 |
| Деталь: | Guide Plate:Transport:Low |
| Парткод: | B1324730 |
| Деталь: | Spring Plate - Driven Rol |
| Парткод: | B0654731 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF022077 |
| Деталь: | Guide Plate Band |
| Парткод: | A0964928 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA063581 |
| Деталь: | Guide Plate Pressure Hold |
| Парткод: | A2294727 |
| Деталь: | Guide Stopper Roller |
| Парткод: | AF022067 |
| Деталь: | Guide Plate Lever |
| Парткод: | B0654531 |
| Деталь: | Decal - Guide Plate Lever |
| Парткод: | B0654867 |
| Деталь: | Guide Plate Lever Hook |
| Парткод: | B0654933 |
| Деталь: | Tapping Screw - 4x6 |
| Парткод: | 04514006N |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 04504008N |
| Деталь: | Tapping Screw:M4x10 |
| Парткод: | 04504010N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Harness Clamp - ES-0505 |
| Парткод: | 11050328 |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Duct:Side Plate:Rear:Fron |
| Парткод: | B1322443 |
| Деталь: | Toner Outlet Sub-unit:Cov |
| Парткод: | B1326572 |
| Деталь: | Transport Screw:Side |
| Парткод: | B1326556 |
| Деталь: | Toner Outlet Sub-unit |
| Парткод: | B1326570 |
| Деталь: | Gear:29Z |
| Парткод: | B1326592 |
| Деталь: | Gear:25Z |
| Парткод: | AB010135 |
| Деталь: | Holder:Drive Sub-unit |
| Парткод: | B1321316 |
| Деталь: | Shaft:Horizontal:Assy |
| Парткод: | B1321311 |
| Деталь: | Holder:Drive Sub-unit |
| Парткод: | B1321320 |
| Деталь: | Flange:Timing Pulley |
| Парткод: | B1321312 |
| Деталь: | Timing Belt:40S2M308 |
| Парткод: | AA043300 |
| Деталь: | Timing Pulley:30T |
| Парткод: | AB030300 |
| Деталь: | Shaft: Drive: Diagonal, slan |
| Парткод: | B1321315 |
| Деталь: | Gear:30Z |
| Парткод: | AB013189 |
| Деталь: | Gear:26Z |
| Парткод: | AB013122 |
| Деталь: | Case:Drive:Assy |
| Парткод: | B1326540 |
| Деталь: | Shaft: Drive: Short :Assy |
| Парткод: | B1326545 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Transport Screw:Lengthwis |
| Парткод: | B1326561 |
| Деталь: | PIPE |
| Парткод: | B1326531 |
| Деталь: | Duct:Connecting:Pull Out |
| Парткод: | B1322462 |
| Деталь: | Cover:Drawer |
| Парткод: | B1321229 |
| Деталь: | Toner Catchpan:CM |
| Парткод: | B1326597 |
| Деталь: | Toner Catchpan:K |
| Парткод: | B1326599 |
| Деталь: | Arm:Tightener |
| Парткод: | B1321325 |
| Деталь: | TENSION SPRING |
| Парткод: | AA060160 |
| Деталь: | Screw: DIA4 : M3 |
| Парткод: | AA143550 |
| Деталь: | Toner Outlet Sub-unit:Ass |
| Парткод: | B1326533 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | BUSHING - 6MM |
| Парткод: | 8053480 |
| Деталь: | Ball Bearing - 6x15x5 |
| Парткод: | 7403906 |
| Деталь: | Connector:55949-3919 |
| Парткод: | 11029783 |
| Деталь: | Connector:55949-1819 |
| Парткод: | 11029785 |
| Деталь: | Decal - Cover |
| Парткод: | B0654480 |
| Деталь: | Cover:Left Middle |
| Парткод: | B1321506 |
| Деталь: | Cover:Left Lower |
| Парткод: | B1321509 |
| Деталь: | Waste Toner Bottle |
| Парткод: | B1326596 |
| Деталь: | Rivet - M6 |
| Парткод: | B0391367 |
| Деталь: | Cover:Ozone Filter |
| Парткод: | B1321516 |
| Деталь: | Cover:Rear Middle |
| Парткод: | B1321507 |
| Деталь: | Screw:M4:Exterior |
| Парткод: | AA143801 |
| Деталь: | Cover:Rear Upper |
| Парткод: | B1321504 |
| Деталь: | Cover:Right Lower |
| Парткод: | B1321508 |
| Деталь: | Connector cap |
| Парткод: | B0651341 |
| Деталь: | Cover:Rear Lower:Assy |
| Парткод: | B1321471 |
| Деталь: | Cover:Right Middle |
| Парткод: | B1321505 |
| Деталь: | G4 Cap |
| Парткод: | B0651344 |
| Деталь: | LCT Cover |
| Парткод: | B0651303 |
| Деталь: | Tapping Screw - 4x10 |
| Парткод: | 04514010N |
| Деталь: | Paper Tray: Universal: DOM: |
| Парткод: | B1326770 |
| Деталь: | Link:Side Fence |
| Парткод: | B1326789 |
| Деталь: | Link:End Fence |
| Парткод: | B1326788 |
| Деталь: | Side Fence:Front:Assy |
| Парткод: | B1326793 |
| Деталь: | Positioning Stopper Lever |
| Парткод: | B0656538 |
| Деталь: | Spring Plate |
| Парткод: | A1342978 |
| Деталь: | Plate:Side Fence |
| Парткод: | B1326791 |
| Деталь: | Side Fence Pad |
| Парткод: | A0966553 |
| Деталь: | Tray Bottom Plate:Assy |
| Парткод: | B1326785 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF013005 |
| Деталь: | Side Fence:Rear:Assy |
| Парткод: | B1326795 |
| Деталь: | Rear Lever Stopper |
| Парткод: | A2672860 |
| Деталь: | Side Fence Stopper |
| Парткод: | A2672859 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A2672857 |
| Деталь: | Decal - Paper Level |
| Парткод: | AA002010 |
| Деталь: | Spring Plate:Paper Tray:E |
| Парткод: | B1326798 |
| Деталь: | Decal:Paper Tray:Paper Se |
| Парткод: | B1326786 |
| Деталь: | Decal - Positioning |
| Парткод: | B0656545 |
| Деталь: | Arm:End Fence:Lock |
| Парткод: | B1326783 |
| Деталь: | END FENCE |
| Парткод: | AF017032 |
| Деталь: | Side Fence:Rear:Auxiliary |
| Парткод: | B1326797 |
| Деталь: | Gear:16z |
| Парткод: | AB012327 |
| Деталь: | Misfeed Removal Guide |
| Парткод: | A1766695 |
| Деталь: | Tension Spring:Side Fence |
| Парткод: | AA060961 |
| Деталь: | Bottom Plate Lift Shaft |
| Парткод: | B0656524 |
| Деталь: | Lift Lever |
| Парткод: | B0656526 |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 04504008N |
| Деталь: | Screw - M4X8 |
| Парткод: | 03604008N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Harness:Transfer Unit:MCY |
| Парткод: | B1325352 |
| Деталь: | Terminal:Collar |
| Парткод: | B1326140 |
| Деталь: | Terminal:Yellow |
| Парткод: | B1326149 |
| Деталь: | Compression Spring:Transf |
| Парткод: | B1326147 |
| Деталь: | Plate:Upper:Positioning S |
| Парткод: | B1326178 |
| Деталь: | Positioning Sensor:Assy |
| Парткод: | B1326141 |
| Деталь: | Image Transfer Belt |
| Парткод: | B1326050 |
| Деталь: | Harness:Positioning Senso |
| Парткод: | B1325378 |
| Деталь: | Bushing:Front |
| Парткод: | B1326116 |
| Деталь: | BUSHING |
| Парткод: | B1326115 |
| Деталь: | Compression Spring:Transf |
| Парткод: | B1326144 |
| Деталь: | Roller:Driven |
| Парткод: | B1326061 |
| Деталь: | Roller:Intermediate Trans |
| Парткод: | B1326080 |
| Деталь: | Bracket:Collar |
| Парткод: | B1326077 |
| Деталь: | Harness:Transfer Unit:K |
| Парткод: | B1325351 |
| Деталь: | Terminal:Black |
| Парткод: | B1326137 |
| Деталь: | Shaft:Contact Point:Colla |
| Парткод: | B1326098 |
| Деталь: | Compression Spring:Transf |
| Парткод: | B1326133 |
| Деталь: | Bracket:On-off:Black |
| Парткод: | B1326076 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 04513008N |
| Деталь: | Screw - M3X6 |
| Парткод: | 03603006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | CLAMP |
| Парткод: | 11050534 |
| Деталь: | Stepper Motor:Paper Feed |
| Парткод: | B1326655 |
| Деталь: | TENSION SPRING |
| Парткод: | AA060958 |
| Деталь: | Bracket:Drive:Paper Feed |
| Парткод: | B1322760 |
| Деталь: | Timing Pulley:35T |
| Парткод: | AB030301 |
| Деталь: | Timing Belt:40S2M150 |
| Парткод: | AA043313 |
| Деталь: | Spacer - 1x8x12 |
| Парткод: | AA132025 |
| Деталь: | Ball Bearing - 8x12x5 |
| Парткод: | A2472800 |
| Деталь: | Gear:103Z |
| Парткод: | AB010133 |
| Деталь: | Shaft: Drive :Vacuum |
| Парткод: | B1321367 |
| Деталь: | Gear:22Z |
| Парткод: | AB011250 |
| Деталь: | DC Motor: DIA86 : 3 8W |
| Парткод: | AX060279 |
| Деталь: | Bracket:Drive:Fusing: Ass |
| Парткод: | B1321350 |
| Деталь: | Timing Pulley:47T |
| Парткод: | AB030770 |
| Деталь: | Timing Pulley:47T |
| Парткод: | AB030768 |
| Деталь: | Gear: Pulley :96Z/3 0T |
| Парткод: | AB017685 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA060951 |
| Деталь: | Bracket:Tightener:Assy |
| Парткод: | B1321356 |
| Деталь: | Shaft:Drive:Fusing:Assy |
| Парткод: | B1321360 |
| Деталь: | Pulley:Idler |
| Парткод: | B1321370 |
| Деталь: | Timing Belt:40S3M471 |
| Парткод: | AA043965 |
| Деталь: | Timing Belt:60S3M741 |
| Парткод: | AA043964 |
| Деталь: | Timing Pulley:44t |
| Парткод: | AB030771 |
| Деталь: | Timing Pulley:44t |
| Парткод: | AB030772 |
| Деталь: | Shaft:Drive:Reverse:Assy |
| Парткод: | B1321363 |
| Деталь: | Bracket:Sub:Drive:Fusing |
| Парткод: | B1321355 |
| Деталь: | Gear:40Z |
| Парткод: | AB011304 |
| Деталь: | Gear:30Z |
| Парткод: | AB011302 |
| Деталь: | Bracket: Gear: Swivel |
| Парткод: | B1322679 |
| Деталь: | Spacer:MM12 |
| Парткод: | B1322699 |
| Деталь: | Shaft:Drive:Paper Feed |
| Парткод: | B1322762 |
| Деталь: | Gear:33Z |
| Парткод: | AB011303 |
| Деталь: | Harness:Fusing:100V:C1a ( |
| Парткод: | B1325371 |
| Деталь: | Harness:Power Supply Unit |
| Парткод: | B1325372 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 03530060N |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Screw - M4X8 |
| Парткод: | 09544008N |
| Деталь: | Screw:M4x10 |
| Парткод: | 03604010N |
| Деталь: | Screw - M4X6 |
| Парткод: | 03604006N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8050088 |
| Деталь: | Bushing - 8x12x3.5mm |
| Парткод: | 8053497 |
| Деталь: | Parallel Pin - 3x14 |
| Парткод: | 06330140G |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | Harness Clamp |
| Парткод: | 11050488 |
| Деталь: | Parallel Pin - 3x16mm |
| Парткод: | 06330160G |
| Деталь: | Fusing Unit (NA) |
| Парткод: | B1324034 |
| Деталь: | Heater - 350W/120V |
| Парткод: | AX430138 |
| Деталь: | Heater - 590W/120V |
| Парткод: | AX440226 |
| Деталь: | Heater - 350W/120V |
| Парткод: | AX430140 |
| Деталь: | Thermostat :190C:250V/17A |
| Парткод: | AW110042 |
| Деталь: | Thermostat:189C:250V/17A |
| Парткод: | AW110043 |
| Деталь: | Temperature Sensor:Assy |
| Парткод: | B1324150 |
| Деталь: | Thermostat:149C:250V/17A |
| Парткод: | AW110045 |
| Деталь: | Thermostat:150C:250V/17A |
| Парткод: | AW110044 |
| Деталь: | Thermistor:Pressure Rolle |
| Парткод: | AW100098 |
| Деталь: | Fusing Cover |
| Парткод: | B1324320 |
| Деталь: | Stay:Fusing Unit |
| Парткод: | B1324071 |
| Деталь: | Harness : Thermostat :Upper |
| Парткод: | B1324152 |
| Деталь: | Fusing Entrance Guide Pla |
| Парткод: | B1324133 |
| Деталь: | Plate : Temperature Sensor: |
| Парткод: | B1324158 |
| Деталь: | Heater Holder:Upper Front |
| Парткод: | B1324144 |
| Деталь: | Plate : Temperature Sensor: |
| Парткод: | B1324159 |
| Деталь: | Heater Holder:Hot Roller |
| Парткод: | B1324145 |
| Деталь: | Housing:Temperature Senso |
| Парткод: | B1324149 |
| Деталь: | Fusing Entrance Guide Pla |
| Парткод: | B1324273 |
| Деталь: | Heater Holder:Lower |
| Парткод: | B1324245 |
| Деталь: | Knob Screw - 4m |
| Парткод: | B0514103 |
| Деталь: | Thermostat Terminal |
| Парткод: | B0654121 |
| Деталь: | Fusing Protective Sheet |
| Парткод: | B1324289 |
| Деталь: | Tag :Red: Short |
| Парткод: | A2323936 |
| Деталь: | Screw - M3x8 |
| Парткод: | 09543008N |
| Деталь: | Screw - M3X6 |
| Парткод: | 09543006N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 03530060N |
| Деталь: | Screw: Polished Round/Spri |
| Парткод: | 09543010N |
| Деталь: | INTERFACE CABLE |
| Парткод: | B1325369 |
| Деталь: | Cable: LVDS: LDB |
| Парткод: | B1325367 |
| Деталь: | PCB:BICU |
| Парткод: | B1325133 |
| Деталь: | PCB:IOB |
| Парткод: | B1325410 |
| Деталь: | Harness:Upper Front |
| Парткод: | B1325375 |
| Деталь: | Harness:Upper Rear |
| Парткод: | B1325231 |
| Деталь: | Harness :Middle |
| Парткод: | B1325379 |
| Деталь: | Harness:IOB:PP1:PFC |
| Парткод: | B1325381 |
| Деталь: | Harness:Shielded Wire:MB |
| Парткод: | B1325214 |
| Деталь: | PCB:PPB |
| Парткод: | B1325435 |
| Деталь: | Bracket:PPB |
| Парткод: | B1325960 |
| Деталь: | Bracket:Mother Board |
| Парткод: | B1325961 |
| Деталь: | Harness:CSS |
| Парткод: | B1325370 |
| Деталь: | PCB: DDR - DIMM: 256MB |
| Парткод: | B1325763 |
| Деталь: | PCB:Mother Board |
| Парткод: | B1325766 |
| Деталь: | Harness:HDD:Fan Motor |
| Парткод: | B1325993 |
| Деталь: | Bracket:CSS |
| Парткод: | B1325966 |
| Деталь: | PCB:N-PI :Assy |
| Парткод: | B1885731 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw:Round Point |
| Парткод: | 8025291 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Edge Saddle - Les-1010 |
| Парткод: | 11050518 |
| Деталь: | Clamp:EMT-5N |
| Парткод: | 11050559 |
| Деталь: | Nylon Clamp - EMT-2N |
| Парткод: | 11050528 |
| Деталь: | Ferrite Core - TFC-23-11- |
| Парткод: | 16070721 |
| Деталь: | Manual Feed Unit:Assy |
| Парткод: | B1322800 |
| Деталь: | Cover:Manual Feed Unit |
| Парткод: | B1322859 |
| Деталь: | Holder:Manual Feed Table: |
| Парткод: | B1322819 |
| Деталь: | Harness:Manual Feed Unit |
| Парткод: | B1325249 |
| Деталь: | Feeler:Paper End Sensor |
| Парткод: | B1322845 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW020160 |
| Деталь: | Feeler Roller |
| Парткод: | A1342661 |
| Деталь: | Bracket:Sensor:Manual Fee |
| Парткод: | B1322848 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW010107 |
| Деталь: | TENSION SPRING |
| Парткод: | AA060952 |
| Деталь: | DC Solenoid:Pickup:Assy |
| Парткод: | B1322839 |
| Деталь: | One-way Clutch |
| Парткод: | AA083014 |
| Деталь: | Gear:42z |
| Парткод: | AB011307 |
| Деталь: | Roller:Manual Feed Unit:D |
| Парткод: | B1322856 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA082118 |
| Деталь: | Stopper:Magnetic Clutch |
| Парткод: | B1322857 |
| Деталь: | Holder:Manual Feed Table: |
| Парткод: | B1322823 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Paper Feed Roller:Feed:Ma |
| Парткод: | AF031081 |
| Деталь: | Bushing - M8 |
| Парткод: | AA082116 |
| Деталь: | Gear - 15T |
| Парткод: | 54472706 |
| Деталь: | Paper Feed Roller:Pickup |
| Парткод: | AF030080 |
| Деталь: | Guide Plate:Feed |
| Парткод: | B1322837 |
| Деталь: | Ground Plate:Manual Feed |
| Парткод: | B1322846 |
| Деталь: | Arm:Pickup:Manual Feed |
| Парткод: | B1322835 |
| Деталь: | Shaft:Feed Roller |
| Парткод: | AA140761 |
| Деталь: | Bushing - 8x18x11 |
| Парткод: | AA083013 |
| Деталь: | Magnetic Clutch:0.53N M:3 |
| Парткод: | AX200277 |
| Деталь: | Guide Plate:Separator Ass |
| Парткод: | B1322825 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF013016 |
| Деталь: | Shaf t: Separator: Drive: Ass |
| Парткод: | B1322849 |
| Деталь: | Gear:24Z |
| Парткод: | AB011306 |
| Деталь: | Paper Feed Roller:Separat |
| Парткод: | AF032080 |
| Деталь: | Torque Limiter - 53mnxm |
| Парткод: | A2946700 |
| Деталь: | Shaf t: Separator: Driven: As |
| Парткод: | B1322851 |
| Деталь: | Gear:21Z |
| Парткод: | AB011305 |
| Деталь: | TENSION SPRING |
| Парткод: | AA060954 |
| Деталь: | Lever:Pressure:Separator |
| Парткод: | B1322853 |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 04503010N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 8050088 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Tension Spring:Hot Roller |
| Парткод: | B1324194 |
| Деталь: | STAY:UPPER |
| Парткод: | B1324103 |
| Деталь: | Bracket :Guide Plate :Upper |
| Парткод: | B1324132 |
| Деталь: | Fusing Belt |
| Парткод: | B1324090 |
| Деталь: | GEAR:UPPER:53Z |
| Парткод: | AB013762 |
| Деталь: | Hot Roller |
| Парткод: | AE010064 |
| Деталь: | Lever:Heat Roller:Rear |
| Парткод: | B1324120 |
| Деталь: | HEAT ROLLER |
| Парткод: | B1324085 |
| Деталь: | Side Plate:Upper Rear |
| Парткод: | B1324101 |
| Деталь: | Harness:Fusing Unit:No.2 |
| Парткод: | B1325205 |
| Деталь: | Ball Bearing:DIA30xDIA37x |
| Парткод: | AE030057 |
| Деталь: | Thermal Insulating Bushin |
| Парткод: | AE032027 |
| Деталь: | Gear Hot Roller:47Z |
| Парткод: | AB013761 |
| Деталь: | Gear - 46Z |
| Парткод: | AB013702 |
| Деталь: | Gear:Drive:Press Fit |
| Парткод: | B1324134 |
| Деталь: | Harness : Thermostat :Upper |
| Парткод: | B1324151 |
| Деталь: | Lever:Heat Roller:Front |
| Парткод: | B1324121 |
| Деталь: | Side Plate:Upper Front |
| Парткод: | B1324102 |
| Деталь: | Collar: Shaft :Drive |
| Парткод: | B1324125 |
| Деталь: | Roller: Coupling : Knob :Fusi |
| Парткод: | B1324138 |
| Деталь: | Gear - 24Z |
| Парткод: | AB013703 |
| Деталь: | Ball Bearing : DIA25 : DIA3 7 |
| Парткод: | AE030058 |
| Деталь: | Ball Bearing - 8x15.6x4mm |
| Парткод: | AE030013 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | A0774239 |
| Деталь: | Adjusting Pin:Heat Roller |
| Парткод: | B1324122 |
| Деталь: | Harness Clamp |
| Парткод: | B1324189 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52062684 |
| Деталь: | Heater Holder: Upper Rear |
| Парткод: | B1324143 |
| Деталь: | Spacer : Gear : Idler |
| Парткод: | B1324119 |
| Деталь: | Stopper:Heat Roller:Upper |
| Парткод: | B1324147 |
| Деталь: | Retaining Ring C - M25 |
| Парткод: | 07250250E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 03530060N |
| Деталь: | Knob: Front |
| Парткод: | B1327008 |
| Деталь: | Decal:LED:El |
| Парткод: | B1327130 |
| Деталь: | Decal:LED:Dl |
| Парткод: | B1327131 |
| Деталь: | Knob Joint |
| Парткод: | A1664290 |
| Деталь: | Fusing Unit Knob |
| Парткод: | AG051144 |
| Деталь: | Inner Cover:Pull Out:Left |
| Парткод: | B1321198 |
| Деталь: | Lever:Release |
| Парткод: | B1322716 |
| Деталь: | LED:Red:MU93-5001 |
| Парткод: | B1327146 |
| Деталь: | Bracket:LED:Left |
| Парткод: | B1327121 |
| Деталь: | Fan Motor:Assy |
| Парткод: | B1326940 |
| Деталь: | Harness:Front:Fan |
| Парткод: | B1325243 |
| Деталь: | Bracket:LED:Pull Out:Righ |
| Парткод: | B1321239 |
| Деталь: | Lever:Pull Out:Printing |
| Парткод: | B1321184 |
| Деталь: | Inner Cover:Pull Out:Midd |
| Парткод: | B1321200 |
| Деталь: | Decal:Caution:Pull Out |
| Парткод: | B1321238 |
| Деталь: | Duct: Fusing :Vacuum:Ass y |
| Парткод: | B1326931 |
| Деталь: | Fan Motor:Mm60 |
| Парткод: | AX640151 |
| Деталь: | Registration Roller Knob |
| Парткод: | A0602512 |
| Деталь: | Inner Cover:Pull Out:Righ |
| Парткод: | B1321189 |
| Деталь: | Decal: Lever: B4 |
| Парткод: | B1322709 |
| Деталь: | Seal:Duct:Upper |
| Парткод: | B1326925 |
| Деталь: | Seal:Inner Cover:Lower |
| Парткод: | B1326928 |
| Деталь: | Cover:Duct:Middle |
| Парткод: | B1327150 |
| Деталь: | Bracket:Inner Cover:Pull |
| Парткод: | B1321240 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Screw:M4x8 |
| Парткод: | 03540080N |
| Деталь: | Screw-m4x6 |
| Парткод: | 03540060N |
| Деталь: | Screw:Polished Round:M4x6 |
| Парткод: | 09514006N |
| Деталь: | Tapping Screw:M3x25 |
| Парткод: | 04513025N |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | Shaft:Cleaner |
| Парткод: | AA143789 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | B3011286 |
| Деталь: | Spacer - M6.5x1 |
| Парткод: | A4181158 |
| Деталь: | Compression Spring:Paper |
| Парткод: | AA063435 |
| Деталь: | SPACER |
| Парткод: | AA132013 |
| Деталь: | Guide Plate Cushion |
| Парткод: | A8061163 |
| Деталь: | Front Entrance Guide |
| Парткод: | B4772172 |
| Деталь: | Feed-in Unit Stopper |
| Парткод: | A6801621 |
| Деталь: | Bushing - 8mm |
| Парткод: | A6281225 |
| Деталь: | Feed Belt Drive Roller |
| Парткод: | A8061293 |
| Деталь: | Separation Shaft |
| Парткод: | B4772191 |
| Деталь: | Feed Belt |
| Парткод: | A8061295 |
| Деталь: | SPRING BELT GUIDE ROLLER |
| Парткод: | A8064261 |
| Деталь: | Feed Belt Driven Roller |
| Парткод: | A8061294 |
| Деталь: | Transport Belt Roller Sha |
| Парткод: | A8061298 |
| Деталь: | Feed Belt Bracket |
| Парткод: | A8061292 |
| Деталь: | Rear Entrance Guide |
| Парткод: | B4772182 |
| Деталь: | Pick-up Roller Lever |
| Парткод: | B4772231 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50530447 |
| Деталь: | Pickup Roller:Coupling |
| Парткод: | B4772226 |
| Деталь: | PICK-UP ROLLER |
| Парткод: | B4772225 |
| Деталь: | Spacer - 6x20x1 |
| Парткод: | AA132171 |
| Деталь: | Timing Belt :B40S2M142 |
| Парткод: | B6522213 |
| Деталь: | Timing Pulley:21T |
| Парткод: | B6522212 |
| Деталь: | Guide:Paper Feed Belt:Fro |
| Парткод: | B6522215 |
| Деталь: | Pick-up Roller Bracket |
| Парткод: | B4772222 |
| Деталь: | Timing Pulley - T19/Z23 S |
| Парткод: | A8062151 |
| Деталь: | Gear - Z18 |
| Парткод: | A8062271 |
| Деталь: | O/I Holder - Assembly |
| Парткод: | B0278521 |
| Деталь: | Cloth Holder |
| Парткод: | B0651371 |
| Деталь: | Cloth - DF Exposure Glass |
| Парткод: | B0651374 |
| Деталь: | Sponge:SD-Card:Plate |
| Парткод: | B1321529 |
| Деталь: | Lever:Guide Plate |
| Парткод: | B1321511 |
| Деталь: | Holder:Stand |
| Парткод: | B1321226 |
| Деталь: | Inner Cover:Paper Feed |
| Парткод: | B1321558 |
| Деталь: | Inner Cover:Paper Feed |
| Парткод: | B1326761 |
| Деталь: | Decal:Caution Chart:Paper |
| Парткод: | B0701307 |
| Деталь: | Hinge:Door:Lower:Assy |
| Парткод: | B1321453 |
| Деталь: | Tray: Holder: PCU |
| Парткод: | B1322393 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG071012 |
| Деталь: | Holder:PCU |
| Парткод: | B1322391 |
| Деталь: | Plate:Drum Shaft |
| Парткод: | B1322392 |
| Деталь: | Gear:Development Roller |
| Парткод: | B1323120 |
| Деталь: | Adjusting Pin:Development |
| Парткод: | B1323079 |
| Деталь: | Panel:Logo |
| Парткод: | B1321531 |
| Деталь: | Operating Instructions - |
| Парткод: | B2008315 |
| Деталь: | Operating Instructions - |
| Парткод: | B2008615 |
| Деталь: | Operating Instructions - |
| Парткод: | B2008715 |
| Деталь: | Hinge:Door:Upper |
| Парткод: | B1321452 |
| Деталь: | Door:Front:Assy |
| Парткод: | B1321456 |
| Деталь: | Cover:Main Switch |
| Парткод: | B1321512 |
| Деталь: | Case:Main Switch |
| Парткод: | B1321513 |
| Деталь: | Grip:Door:Front |
| Парткод: | B1321514 |
| Деталь: | Lever:Micro Switch |
| Парткод: | B1321515 |
| Деталь: | Door Catch |
| Парткод: | B1321526 |
| Деталь: | Cap:Toner Supply:Upper |
| Парткод: | B1323179 |
| Деталь: | Holder:Cap:Receiving Sub- |
| Парткод: | B1323084 |
| Деталь: | Stopper:Charge |
| Парткод: | B0273170 |
| Деталь: | Tapping Screw:4x12 |
| Парткод: | 04504012N |
| Деталь: | Tapping Screw:M4x10 |
| Парткод: | 04504010N |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Sheet:Logo:E-Studio 4500C |
| Парткод: | B1321544 |
| Деталь: | Sheet:Logo:E-Studio 5500C |
| Парткод: | B2001544 |
| Деталь: | Guide Plate:Paper Feed:Lo |
| Парткод: | B6522142 |
| Деталь: | Separation Cap |
| Парткод: | B4772151 |
| Деталь: | Screw:Contact Point |
| Парткод: | AA143790 |
| Деталь: | Separation Support Pad |
| Парткод: | B3011155 |
| Деталь: | Separation Pad Holder |
| Парткод: | B3011156 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Reverse Roller |
| Парткод: | A8592241 |
| Деталь: | Torque Limiter - Separato |
| Парткод: | A2936399 |
| Деталь: | Compression Spring:0.5n |
| Парткод: | B6524156 |
| Деталь: | Bushing - 4mm |
| Парткод: | A6801661 |
| Деталь: | Roller:Driven:Reverse :Mid |
| Парткод: | B6524155 |
| Деталь: | Bracket:Guide Plate:Lower |
| Парткод: | B6522127 |
| Деталь: | Reverse Roller Shaft |
| Парткод: | B4773131 |
| Деталь: | Ball Bearing - 6x13x5 |
| Парткод: | A8592230 |
| Деталь: | Cushion:Guide Plate:Rever |
| Парткод: | B6522128 |
| Деталь: | Stay:Reverse Roller:Assy |
| Парткод: | B6522122 |
| Деталь: | Guide:Stay:Reverse Roller |
| Парткод: | B6522126 |
| Деталь: | Guide Plate:Original Tabl |
| Парткод: | B6522432 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50530447 |
| Деталь: | Gate Pawl:Reverse: Upper |
| Парткод: | B6524203 |
| Деталь: | Cushion - Bin Solenoid Le |
| Парткод: | A4582251 |
| Деталь: | Bracket:Discharge Brush:A |
| Парткод: | B6524205 |
| Деталь: | ANTISTATIC BRUSH |
| Парткод: | A6812416 |
| Деталь: | EXIT ROLLER |
| Парткод: | B6524726 |
| Деталь: | Bracket:Sensor:Reverse:Mi |
| Парткод: | B6524133 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW010117 |
| Деталь: | Guide Plate:Reverse:Middl |
| Парткод: | B6524122 |
| Деталь: | Pin:Guide Plate:Paper Fee |
| Парткод: | AA143788 |
| Деталь: | Hook: Solenoid: Reverse: Upp |
| Парткод: | B6524212 |
| Деталь: | Tens ion Spring: Hook: Gate |
| Парткод: | B6524213 |
| Деталь: | Timing Pulley:44t |
| Парткод: | B6524727 |
| Деталь: | Photointerruptor |
| Парткод: | AW020141 |
| Деталь: | Stay:Frame:Left |
| Парткод: | B4771152 |
| Деталь: | Arm Shaft |
| Парткод: | B4771171 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA143020 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B6521136 |
| Деталь: | Hinge:Left:Assy |
| Парткод: | B6521210 |
| Деталь: | Contact Point Shaft |
| Парткод: | A8061135 |
| Деталь: | Right Frame Stay |
| Парткод: | B4771161 |
| Деталь: | Sheet:Exit:Lower |
| Парткод: | B6521135 |
| Деталь: | Hinge:Right:Assy |
| Парткод: | B6521220 |
| Деталь: | Sensor Feeler |
| Парткод: | B4771185 |
| Деталь: | Sensor bracket |
| Парткод: | B4771181 |
| Деталь: | Detection Sensor Harness |
| Парткод: | B4775611 |
| Деталь: | Harness: Sensor: Reverse: Up |
| Парткод: | B6525446 |
| Деталь: | ANTI-STATIC BRUSH |
| Парткод: | B4772621 |
| Деталь: | Bracket: Pressure: Transpor |
| Парткод: | B6521131 |
| Деталь: | TENSION SPRING |
| Парткод: | B6521132 |
| Деталь: | Pulley:Belt Tensioner |
| Парткод: | A2576112 |
| Деталь: | Cover:Roller:Scanning:Pee |
| Парткод: | B6523136 |
| Деталь: | Bracket:Magnet Catch:Pres |
| Парткод: | B6524904 |
| Деталь: | Front Left Stopper |
| Парткод: | B4771191 |
| Деталь: | Adjusting Pin:Transport B |
| Парткод: | B6521141 |
| Деталь: | Screw:Contact Point |
| Парткод: | AA143790 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Tapping Screw:Round Point |
| Парткод: | 8025291 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 07200030E |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Harness Clamp |
| Парткод: | 11050487 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | Harnessd:Electric Potenti |
| Парткод: | B1325229 |
| Деталь: | Harness:Sensor:KM |
| Парткод: | B1325357 |
| Деталь: | Harness:Sensor:CY |
| Парткод: | B1325358 |
| Деталь: | Power Pack:B |
| Парткод: | AZ320137 |
| Деталь: | Base:Electric Potential S |
| Парткод: | B1325415 |
| Деталь: | Bracket:Power Pack:Develo |
| Парткод: | B1325861 |
| Деталь: | Stay:Bracket:Power Pack:D |
| Парткод: | B1325863 |
| Деталь: | Harness:DRB:ADF:Power Sou |
| Парткод: | B1325258 |
| Деталь: | Stay:Harness:Power Pack:D |
| Парткод: | B1325864 |
| Деталь: | Stay:Duct |
| Парткод: | B1322431 |
| Деталь: | Duct:Exhaust |
| Парткод: | B1322434 |
| Деталь: | Duct:Joint:Exhaust: Assy |
| Парткод: | B1322455 |
| Деталь: | Seal:Duct:Exhaust |
| Парткод: | B1322479 |
| Деталь: | Bracket:Stay:Duct |
| Парткод: | B1322432 |
| Деталь: | Duct:Exhaust:Assy |
| Парткод: | B1326861 |
| Деталь: | Fan Motor MM80 |
| Парткод: | AX640159 |
| Деталь: | Bracket: Stay: Duct: Right |
| Парткод: | B1322433 |
| Деталь: | Duct:Exit:Exhaust: Assy |
| Парткод: | B1326901 |
| Деталь: | Fan:Sirocco:DC2 4 V:2 speed |
| Парткод: | AX650042 |
| Деталь: | Shield:Sirocco |
| Парткод: | B1326966 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Screw - M3X6 |
| Парткод: | 03603006N |
| Деталь: | Tapping Screw:Round Point |
| Парткод: | 8025291 |
| Деталь: | Tapping Screw:4x35 |
| Парткод: | 04514035N |
| Деталь: | Screw:M4x40 |
| Парткод: | 03540400N |
| Деталь: | Harness Clamp |
| Парткод: | 11050488 |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 11050508 |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | Clamp - LES-1017 |
| Парткод: | 11050521 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | Edge Saddle - Les-1010 |
| Парткод: | 11050518 |
| Деталь: | Duct:Development:Front:Y |
| Парткод: | B1322459 |
| Деталь: | Duct: Development: Front |
| Парткод: | B1322458 |
| Деталь: | Seal: Fan Motor |
| Парткод: | B1322485 |
| Деталь: | Fan Motor:MM40:15mm |
| Парткод: | AX640149 |
| Деталь: | Shield:Duct |
| Парткод: | B1322474 |
| Деталь: | Duct:Toner Hopper |
| Парткод: | B1322457 |
| Деталь: | Shield:Duct:Left |
| Парткод: | B1322476 |
| Деталь: | Heat Insulation:Toner Sup |
| Парткод: | B1323246 |
| Деталь: | Cover:Lower:Color |
| Парткод: | B1323230 |
| Деталь: | Toner Supply Unit:Assy |
| Парткод: | B2003335 |
| Деталь: | Tube:Black |
| Парткод: | B1323436 |
| Деталь: | Coil:Guard:Tube:Black |
| Парткод: | B1323438 |
| Деталь: | Toner End Sensor |
| Парткод: | AW230009 |
| Деталь: | Tube:Color |
| Парткод: | B1323437 |
| Деталь: | Coil:Guard:Tube:Color |
| Парткод: | B1323439 |
| Деталь: | Seal:Duct:Toner Hopper:Lo |
| Парткод: | B1322496 |
| Деталь: | Gear:Drive:Toner Supply U |
| Парткод: | B1323349 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA082101 |
| Деталь: | Shaft:Magnetic Clutch |
| Парткод: | B1323346 |
| Деталь: | Magnetic clutch |
| Парткод: | B1323354 |
| Деталь: | BUSHING: DRIVE: SUPPLY: MM6 |
| Парткод: | AA082140 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 04533006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 04503008N |
| Деталь: | Clamp:Lwss-0504 |
| Парткод: | 11050568 |
| Деталь: | Clamp - LHL-18 |
| Парткод: | 11050458 |
| Деталь: | Clamp:LWSS- IN |
| Парткод: | 11050598 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Hinge:C/T Box:Upper |
| Парткод: | B1325933 |
| Деталь: | Hinge:C/T Box:Lower |
| Парткод: | B1325930 |
| Деталь: | Bracket:Guard:Harness |
| Парткод: | B1321113 |
| Деталь: | Fan Motor MM80 |
| Парткод: | AX640159 |
| Деталь: | Bracket:Fan Motor |
| Парткод: | B1325944 |
| Деталь: | Seal:C/T Box:Upper:Side |
| Парткод: | B1325813 |
| Деталь: | Bracket:C/T Box:Right Upp |
| Парткод: | B1325941 |
| Деталь: | Stepped Screw - M4 |
| Парткод: | AA143718 |
| Деталь: | Stopper:C/T Box:Upper |
| Парткод: | B1325989 |
| Деталь: | Bracket:C/T Box:Upper |
| Парткод: | B1325940 |
| Деталь: | Grip:Application |
| Парткод: | B7125605 |
| Деталь: | Large Drum Stay Ground Pl |
| Парткод: | B0706877 |
| Деталь: | GROUNDING PLATE |
| Парткод: | A2677586 |
| Деталь: | Bracket:Interface:Fix: Aux |
| Парткод: | B1325965 |
| Деталь: | Ground Plate:Base:Control |
| Парткод: | B1325807 |
| Деталь: | Bracket:Interface |
| Парткод: | B1325963 |
| Деталь: | Arm:Hinge:C/T Box |
| Парткод: | B1325947 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw:Round Point |
| Парткод: | 8025291 |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 8025282 |
| Деталь: | Tapping Screw:M4x30 |
| Парткод: | 04514030N |
| Деталь: | Clamp:LESR-25 |
| Парткод: | 11050599 |
| Деталь: | Harness Clamp - IWS-2218 |
| Парткод: | 11050490 |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 11050508 |
| Деталь: | Harness Clamp |
| Парткод: | 11050488 |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | Bushing:LE-100 |
| Парткод: | 11060905 |
| Деталь: | Bushing:LE-60 |
| Парткод: | 11060901 |
| Деталь: | Grip:Guide Plate:Upper |
| Парткод: | B1327056 |
| Деталь: | Pawl:Guide Plate:Fix |
| Парткод: | B1327044 |
| Деталь: | Shaft:Release:Guide Plate |
| Парткод: | B1327052 |
| Деталь: | Spring:Tightener |
| Парткод: | AA063908 |
| Деталь: | Stopper:Pipe |
| Парткод: | B1327105 |
| Деталь: | Guide Plate:Transport:Upp |
| Парткод: | B1327016 |
| Деталь: | Spring Plate:Upper:Right |
| Парткод: | B1327013 |
| Деталь: | Roller:Middle |
| Парткод: | B1327031 |
| Деталь: | Bushing:DIA6 |
| Парткод: | AA080213 |
| Деталь: | Guide Plate:Transport:Upp |
| Парткод: | B1327010 |
| Деталь: | Sound Proofing Material |
| Парткод: | B1327124 |
| Деталь: | Guide Plate:Entrance :Uppe |
| Парткод: | B1327129 |
| Деталь: | Guide:Entrance:Right Fron |
| Парткод: | B1327164 |
| Деталь: | Decura:Heat Pipe:DIA15 |
| Парткод: | B1327005 |
| Деталь: | Bracket:Positioning Plate |
| Парткод: | B1327133 |
| Деталь: | Bushing - MM5 |
| Парткод: | AA080240 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA063906 |
| Деталь: | Supporting Plate:Pull Out |
| Парткод: | B1321159 |
| Деталь: | Shaft:Knob |
| Парткод: | B1327037 |
| Деталь: | Gear:28Z |
| Парткод: | B1327002 |
| Деталь: | Bracket:Lever |
| Парткод: | B1327007 |
| Деталь: | Holder:Bearing:Front |
| Парткод: | B1327011 |
| Деталь: | Bracket:Bearing:Front |
| Парткод: | B1327039 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Roller:MM 14 |
| Парткод: | B1327033 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 04503008N |
| Деталь: | Tapping Screw - 4x6 |
| Парткод: | 04514006N |
| Деталь: | Screw - M3X6 |
| Парткод: | 09543006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Ball Bearing - 6x10x3 |
| Парткод: | 7413706 |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 07200030E |
| Деталь: | Harness:Paper Exit Unit |
| Парткод: | B1325244 |
| Деталь: | Bracket:Sensor |
| Парткод: | B1327049 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW010107 |
| Деталь: | Cover:Exhaust |
| Парткод: | B1327023 |
| Деталь: | Discharge Brush |
| Парткод: | AA120084 |
| Деталь: | Stay:Exit:Assy |
| Парткод: | B1327018 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA063577 |
| Деталь: | Ball Bearing:Driven:MM4 |
| Парткод: | AA084053 |
| Деталь: | Exit Roller:Driven:Upper |
| Парткод: | B1327147 |
| Деталь: | Shaft:Lever:Left Inner Re |
| Парткод: | B1327123 |
| Деталь: | Lever:Stopper |
| Парткод: | B1327041 |
| Деталь: | SPRING |
| Парткод: | AA062319 |
| Деталь: | Lever:Open And Close |
| Парткод: | B1327042 |
| Деталь: | Bracket:Stay:Left |
| Парткод: | B1327119 |
| Деталь: | Bracket:Fix:Front |
| Парткод: | B1327043 |
| Деталь: | Duct:Pull Out |
| Парткод: | B1322463 |
| Деталь: | Seal:Duct:Pull Out |
| Парткод: | B1322484 |
| Деталь: | Cover:Base:Pull Out |
| Парткод: | B1321220 |
| Деталь: | Harness:Pull Out:Uni:39pi |
| Парткод: | B1325242 |
| Деталь: | Harness:High Voltage Supp |
| Парткод: | B1325356 |
| Деталь: | Power Pack:D |
| Парткод: | AZ310029 |
| Деталь: | Insulating Sheet:Pull Out |
| Парткод: | B1321228 |
| Деталь: | Knob Screw |
| Парткод: | 54131875 |
| Деталь: | Handle:Pull Out |
| Парткод: | B1321191 |
| Деталь: | Shaft:Lock:Pull Out |
| Парткод: | B1321185 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA063951 |
| Деталь: | Cam:Transfer Roller |
| Парткод: | B1326305 |
| Деталь: | Toner Catchpan |
| Парткод: | B1326285 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | A2675814 |
| Деталь: | Holder:Spring:Pull Out |
| Парткод: | B1321221 |
| Деталь: | Bracket:Release:Lock |
| Парткод: | B1321190 |
| Деталь: | Roller:Lock:Pull Out |
| Парткод: | AA132300 |
| Деталь: | Bracket:Lock |
| Парткод: | B1321183 |
| Деталь: | Supporting Plate:Bracket: |
| Парткод: | B1321224 |
| Деталь: | Bracket:Fix:Rear |
| Парткод: | B1327050 |
| Деталь: | Shaft:Stopper |
| Парткод: | B1327096 |
| Деталь: | Holder:Shaft |
| Парткод: | B1327070 |
| Деталь: | Bracket:Interlock:Lever |
| Парткод: | B1321193 |
| Деталь: | Actuator:Pull Out |
| Парткод: | B1321194 |
| Деталь: | Bracket:Drawer:Pull Out |
| Парткод: | B1321195 |
| Деталь: | Guide Plate:Fusing Unit |
| Парткод: | B1321155 |
| Деталь: | Bracket: Knob: Fusing/paper |
| Парткод: | B1321152 |
| Деталь: | Gear:18Z |
| Парткод: | AB013309 |
| Деталь: | Gear:13/20Z |
| Парткод: | AB017688 |
| Деталь: | Gear - 16Z |
| Парткод: | AB013363 |
| Деталь: | Shaft:Knob:Fusing/Paper E |
| Парткод: | B1321156 |
| Деталь: | Collar:DIA18 |
| Парткод: | B1321235 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Tapping Screw - 4x6 |
| Парткод: | 04514006N |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 03530060N |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 07200030E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Screw-m4x6 |
| Парткод: | 03540060N |
| Деталь: | Bushing - 8mm |
| Парткод: | 8053386 |
| Деталь: | CLAMP |
| Парткод: | 11050534 |
| Деталь: | Clamp:LES-0505 |
| Парткод: | 11050551 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | Pan Head Screw:M4x18 |
| Парткод: | 03140180N |
| Деталь: | Connector:51405-3919 |
| Парткод: | 11029781 |
| Деталь: | Bracket:Connector:Right |
| Парткод: | B1326764 |
| Деталь: | Harness:Bank:Rear:3way |
| Парткод: | B1325396 |
| Деталь: | Connector Spring |
| Парткод: | AA063268 |
| Деталь: | Bracket:Arm:Assy |
| Парткод: | B1326726 |
| Деталь: | Bracket:Connector:Left |
| Парткод: | B1326763 |
| Деталь: | LOCK ARM |
| Парткод: | B0656769 |
| Деталь: | Spring - Large |
| Парткод: | AA062251 |
| Деталь: | DC Motor:Rise:Tandem LCT: |
| Парткод: | B1326759 |
| Деталь: | Spring - Small |
| Парткод: | AA062252 |
| Деталь: | DC Solenoid:Coupling:Ass |
| Парткод: | B1326762 |
| Деталь: | DC Solenoid:Lock:Assy |
| Парткод: | B1326765 |
| Деталь: | Spring:Connector:Tandem L |
| Парткод: | AA063902 |
| Деталь: | Spacer - 6mm |
| Парткод: | AA132203 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | STEPPED SCREW |
| Парткод: | 8030058 |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Binding Self-tapping Scre |
| Парткод: | 04524010N |
| Деталь: | Tens ion Spring: Lock: Lever |
| Парткод: | B6523145 |
| Деталь: | Hook:Lock:Image Reading U |
| Парткод: | B6523144 |
| Деталь: | Shaft:Lever:Misfeed Remov |
| Парткод: | B6523141 |
| Деталь: | Transport Belt |
| Парткод: | B6523121 |
| Деталь: | Roller:Transport Belt:Dri |
| Парткод: | B6523112 |
| Деталь: | Stopper:Roller:Drive |
| Парткод: | B6523119 |
| Деталь: | Discharge Brush:Short |
| Парткод: | B6523158 |
| Деталь: | Discharge Brush:Long |
| Парткод: | B6523157 |
| Деталь: | Discharge Brush:Middle |
| Парткод: | B6523159 |
| Деталь: | ANTI-STATIC BRUSH |
| Парткод: | B4772621 |
| Деталь: | Guide:Transport Belt:Fron |
| Парткод: | B6523116 |
| Деталь: | Housing:Transport Belt Un |
| Парткод: | B6523120 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B6523125 |
| Деталь: | Guide:Transport Belt:Rear |
| Парткод: | B6523117 |
| Деталь: | Spacer:Transport Belt |
| Парткод: | B6523156 |
| Деталь: | Roller:Pressure |
| Парткод: | B6523113 |
| Деталь: | Bracket:Roller:Driven |
| Парткод: | B6523123 |
| Деталь: | Driven Roller:Scanning |
| Парткод: | B6523124 |
| Деталь: | Pin:Guide Plate:Paper Fee |
| Парткод: | AA143788 |
| Деталь: | DC Solenoid:Reverse:Lower |
| Парткод: | B6524766 |
| Деталь: | Leve r: Reve rse: Lowe r:DC So |
| Парткод: | B6524532 |
| Деталь: | Bracket:Reverse:Lower:DC |
| Парткод: | B6524533 |
| Деталь: | Damper - Junction Gate So |
| Парткод: | A6972102 |
| Деталь: | ADF:Assy |
| Парткод: | B1327451 |
| Деталь: | Cover:Front |
| Парткод: | B6521902 |
| Деталь: | Pin:Guide Plate:Paper Fee |
| Парткод: | AA143788 |
| Деталь: | Cover:Rear |
| Парткод: | B6521952 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Stopper:Guide Plate:Press |
| Парткод: | B6524903 |
| Деталь: | Pressure Plate Tape |
| Парткод: | B4772715 |
| Деталь: | Pressure Plate:Assy |
| Парткод: | B6524741 |
| Деталь: | Guide Plate:Pressure Plat |
| Парткод: | B6524902 |
| Деталь: | MAGNET |
| Парткод: | G0121531 |
| Деталь: | Decal:Misfeed Removal |
| Парткод: | B6524905 |
| Деталь: | STEPPED SCREW |
| Парткод: | A8597211 |
| Деталь: | Decal:Misfeed Removal |
| Парткод: | B6521906 |
| Деталь: | Decal:Misfeed Removal:Exi |
| Парткод: | B6521905 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Screw:M5x10 |
| Парткод: | 09515010N |
| Деталь: | Seal:C/T Box:Cover:Side |
| Парткод: | B1325812 |
| Деталь: | Seal:C/T Box:Cover:Middle |
| Парткод: | B1325809 |
| Деталь: | Gasket:Cover:C/T Box |
| Парткод: | B1325831 |
| Деталь: | Cover:C/T Box:Small |
| Парткод: | B1325958 |
| Деталь: | Harness:HDD:RAID1 |
| Парткод: | B1325731 |
| Деталь: | Harness: HDD: RAID2 |
| Парткод: | B1325732 |
| Деталь: | Harness: HDD: RAID3 |
| Парткод: | B1325733 |
| Деталь: | Harness:HDD:RAID4 |
| Парткод: | B1325734 |
| Деталь: | Harness:HDD:Power Source |
| Парткод: | B1325735 |
| Деталь: | HDD Assy |
| Парткод: | B1325820 |
| Деталь: | PCB:Interface |
| Парткод: | B1325762 |
| Деталь: | Right Guide 1 |
| Парткод: | G1085108 |
| Деталь: | Left Guide 1 |
| Парткод: | G1085107 |
| Деталь: | NVRAM |
| Парткод: | B1329590 |
| Деталь: | Sheet:Cover:C/T Box |
| Парткод: | B1325832 |
| Деталь: | PCB:Control Board |
| Парткод: | B1325769 |
| Деталь: | SD-Card:Copy |
| Парткод: | B1325730 |
| Деталь: | Rail: Upper: Long: Right |
| Парткод: | B1325923 |
| Деталь: | Rail:Upper:Long:Left |
| Парткод: | B1325924 |
| Деталь: | Drum Stay:Control Board:W |
| Парткод: | B1325928 |
| Деталь: | Ground Plate:Panel |
| Парткод: | B0706899 |
| Деталь: | Large Drum Stay Ground Pl |
| Парткод: | B0706877 |
| Деталь: | Ground Plate:Drum Stay:Sm |
| Парткод: | B0706879 |
| Деталь: | Grip:Bracket:Control Boar |
| Парткод: | B1325816 |
| Деталь: | Decal:Caption:Interface |
| Парткод: | B1325818 |
| Деталь: | Cover:SD-Card:Control Boa |
| Парткод: | B1325969 |
| Деталь: | Cover:Connector:Control B |
| Парткод: | B1325925 |
| Деталь: | Interface Panel Assy |
| Парткод: | B0706894 |
| Деталь: | Knob Screw:Panel |
| Парткод: | B0706898 |
| Деталь: | Guard: GAP: C/T Box |
| Парткод: | B1321528 |
| Деталь: | Decal:Caution:HDD:Fan |
| Парткод: | B1325819 |
| Деталь: | Cover:C/T Box |
| Парткод: | B1325957 |
| Деталь: | Stepper Motor: Reverse: Ass |
| Парткод: | B1324780 |
| Деталь: | Bracket: Motor: Reverse: Ass |
| Парткод: | B1324810 |
| Деталь: | Gear:22/24Z |
| Парткод: | AB017687 |
| Деталь: | TIMING BELT |
| Парткод: | AA043291 |
| Деталь: | DC Solenoid:Reversal:Ass |
| Парткод: | B1324745 |
| Деталь: | Stepper Motor:Jogger:Ass |
| Парткод: | B1324650 |
| Деталь: | Bracket:Stepper Motor:Jog |
| Парткод: | B1324696 |
| Деталь: | Stepper Motor:Transport:A |
| Парткод: | B1324785 |
| Деталь: | Bracket:Stepper Motor:Tra |
| Парткод: | B1324789 |
| Деталь: | Timing Belt:40S2M360G |
| Парткод: | AA043309 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Lever:Roller:Driven:Rever |
| Парткод: | B1324663 |
| Деталь: | TENSION SPRING |
| Парткод: | AA062327 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA082118 |
| Деталь: | Stay:Bearing:Reversal |
| Парткод: | B1324665 |
| Деталь: | MAGNETIC |
| Парткод: | AA021034 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA143183 |
| Деталь: | Jogger Fence:Front |
| Парткод: | B1324681 |
| Деталь: | JOGGER FENCE:REAR |
| Парткод: | B1324682 |
| Деталь: | Spring Plate - Rear Jogge |
| Парткод: | B0654683 |
| Деталь: | Stepped Screw - M3X4 |
| Парткод: | AA143811 |
| Деталь: | Table:Duplex:Left |
| Парткод: | B1324720 |
| Деталь: | Arm:Roller:Reversal:Drive |
| Парткод: | B1324661 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA063592 |
| Деталь: | Driven Reversal Roller |
| Парткод: | AF020591 |
| Деталь: | Bushing - 8x10x5 |
| Парткод: | AA082063 |
| Деталь: | Reversal Roller Shaft |
| Парткод: | AA148631 |
| Деталь: | Bracket: Reversal: Driven:A |
| Парткод: | B1324655 |
| Деталь: | Tapping Screw - 4x6 |
| Парткод: | 04514006N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 04504008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 07200030E |
| Деталь: | CLAMP |
| Парткод: | 11050534 |
| Деталь: | Screw-m3x5 |
| Парткод: | 03530050N |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 11050508 |
| Деталь: | Decal:Main Switch Display |
| Парткод: | B1321553 |
| Деталь: | Decal - Main Switch Displ |
| Парткод: | B1321555 |
| Деталь: | Inner Cover:Main Switch |
| Парткод: | B1321551 |
| Деталь: | Shaft:Micro Switch:Front |
| Парткод: | B1325855 |
| Деталь: | Lever:Micro Switch |
| Парткод: | B1325853 |
| Деталь: | Safety switch spring |
| Парткод: | A2571165 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG071012 |
| Деталь: | Bracket:Main Switch |
| Парткод: | B1325851 |
| Деталь: | Screw:Micro Switch |
| Парткод: | B1325852 |
| Деталь: | Duct: Main: Vacuum: Ass y |
| Парткод: | B1326876 |
| Деталь: | Fan Motor:Mm60 |
| Парткод: | AX640151 |
| Деталь: | Duct:Main:Heat Sinker:Ass |
| Парткод: | B1326871 |
| Деталь: | Humidity Control:Assy |
| Парткод: | B1322409 |
| Деталь: | Seal:Fan:Humidity Control |
| Парткод: | B1322465 |
| Деталь: | Fan Motor:MM60:25mm:24V |
| Парткод: | AX640150 |
| Деталь: | FILTER |
| Парткод: | B1322468 |
| Деталь: | Humidity Control:Assy |
| Парткод: | B1322410 |
| Деталь: | Duct: Imaging Unit: Rear: As |
| Парткод: | B1326926 |
| Деталь: | Duct:Imaging Unit:Front:A |
| Парткод: | B1326921 |
| Деталь: | Fan Motor:15mm:24V |
| Парткод: | AX640164 |
| Деталь: | Bracket:Connector |
| Парткод: | B1322489 |
| Деталь: | Bracket:Drawer:Toner Supp |
| Парткод: | B1323489 |
| Деталь: | Cover:Drawer |
| Парткод: | B1323491 |
| Деталь: | Bracket:Fix:Toner Supply |
| Парткод: | B1323493 |
| Деталь: | Duct: Vacuum: Entrance |
| Парткод: | B1326855 |
| Деталь: | Duct: Vacuum:Ass y |
| Парткод: | B1326851 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw:M3x25 |
| Парткод: | 04513025N |
| Деталь: | Tapping Screw:M4x25 |
| Парткод: | 04514025N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | SWITCH |
| Парткод: | 12042598 |
| Деталь: | MICRO SWITCH |
| Парткод: | 12042521 |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 11050508 |
| Деталь: | Screw:M4x8 |
| Парткод: | 03540080N |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | Clamp:LES-0505 |
| Парткод: | 11050551 |
| Деталь: | Relay Connector - 4P |
| Парткод: | 11026246 |
| Деталь: | Connector:55949-3919 |
| Парткод: | 11029783 |
| Деталь: | Paper Feed Motor - DC 7.4 |
| Парткод: | B4773711 |
| Деталь: | Paper Feed Motor Stay |
| Парткод: | B4773115 |
| Деталь: | Paper Feed Motor Bracket |
| Парткод: | B4773111 |
| Деталь: | TENSION SPRING |
| Парткод: | AA060842 |
| Деталь: | Spacer:Reverse Roller:Rea |
| Парткод: | B6521633 |
| Деталь: | Gear - 37Z |
| Парткод: | B4773161 |
| Деталь: | Gear - 31Z |
| Парткод: | B4773151 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | PULLEY |
| Парткод: | A5482139 |
| Деталь: | Separation Shaft Stopper |
| Парткод: | A8062244 |
| Деталь: | Gear - 24Z |
| Парткод: | B4773123 |
| Деталь: | Ball Bearing - 6x13x5 |
| Парткод: | A8592230 |
| Деталь: | Separation Roller Shaft |
| Парткод: | B4773121 |
| Деталь: | Feeler - Pick-up Roller C |
| Парткод: | A6802262 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50530447 |
| Деталь: | Pick-up Roller Cam |
| Парткод: | B4773251 |
| Деталь: | Stepper Motor:MM42:0.95A: |
| Парткод: | AX040139 |
| Деталь: | Gear - 20Z |
| Парткод: | B4773143 |
| Деталь: | Timing Belt :B40S3M186 |
| Парткод: | B6521643 |
| Деталь: | Gear - 23Z |
| Парткод: | B4773141 |
| Деталь: | PULLEY |
| Парткод: | B4773177 |
| Деталь: | Photointerruptor |
| Парткод: | AW020141 |
| Деталь: | Timing Belt :B40S2M178 |
| Парткод: | B6521773 |
| Деталь: | Pulley - 39Z |
| Парткод: | B3012141 |
| Деталь: | Timing Belt :B60S2M212 |
| Парткод: | B6521613 |
| Деталь: | PULLEY |
| Парткод: | B4773145 |
| Деталь: | Paper Feed Drive Bracket |
| Парткод: | B4773181 |
| Деталь: | PULLEY |
| Парткод: | B4773171 |
| Деталь: | Timing Belt :B40S2M170 |
| Парткод: | B6521674 |
| Деталь: | Timing Belt :B40S3M180 |
| Парткод: | B6521673 |
| Деталь: | PULLEY |
| Парткод: | B4773173 |
| Деталь: | Damper - Junction Gate So |
| Парткод: | A6972102 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B6521134 |
| Деталь: | Shaft:Slider |
| Парткод: | B6521133 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Tapping Screw - 4x6 |
| Парткод: | 04514006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Harness Clamp |
| Парткод: | 11050487 |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Parallel Pin - 2x12 |
| Парткод: | 06320120G |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 07200030E |
| Деталь: | Bushing: DIA4x6 |
| Парткод: | 07074060N |
| Деталь: | Gate Pawl:Reverse:Lower:L |
| Парткод: | B6524527 |
| Деталь: | Gate Pawl:Reverse:Lower:R |
| Парткод: | B6524528 |
| Деталь: | Cushion - Bin Solenoid Le |
| Парткод: | A4582251 |
| Деталь: | Bushing: Reverse: Lower: Gat |
| Парткод: | B6524520 |
| Деталь: | Roller: Scanning: Exit: Driv |
| Парткод: | B6524519 |
| Деталь: | Driven Exit Arm |
| Парткод: | B4772637 |
| Деталь: | Exit Arm Spring |
| Парткод: | B4774127 |
| Деталь: | Guide Plate:Reverse:Lower |
| Парткод: | B6524516 |
| Деталь: | Stepped Screw - M6 |
| Парткод: | A2322356 |
| Деталь: | Short Arm Shaft |
| Парткод: | B4772645 |
| Деталь: | Long Arm Shaft |
| Парткод: | B4772641 |
| Деталь: | Lever: Reverse: Lower |
| Парткод: | B6524529 |
| Деталь: | Driven Exit Scanning Roll |
| Парткод: | B4772636 |
| Деталь: | Arm: Pressure: Reverse: Lowe |
| Парткод: | B6524517 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B6524518 |
| Деталь: | TENSION SPRING |
| Парткод: | B6524530 |
| Деталь: | Seal - 0.7x13x20 |
| Парткод: | A4221063 |
| Деталь: | ANTI-STATIC BRUSH |
| Парткод: | B4772621 |
| Деталь: | Bracket:Reverse:Lower |
| Парткод: | B6524522 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | BUSHING - 6MM |
| Парткод: | 50530447 |
| Деталь: | Pin:Guide Plate:Paper Fee |
| Парткод: | AA143788 |
| Деталь: | EXIT ROLLER |
| Парткод: | B6524726 |
| Деталь: | Guide Plate:Reverse:Lower |
| Парткод: | B6524602 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B6521853 |
| Деталь: | Bushing- Exit Driven Roll |
| Парткод: | A8594836 |
| Деталь: | DRIVEN EXIT ROLLER |
| Парткод: | B4772861 |
| Деталь: | Cover:Exit |
| Парткод: | B6521852 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW010117 |
| Деталь: | Harness:Sensor:Reverse:Lo |
| Парткод: | B6525456 |
| Деталь: | Cover: Sensor: Reverse: Lowe |
| Парткод: | B6521854 |
| Деталь: | Ball Bearing - 6x13x5 |
| Парткод: | A8592230 |
| Деталь: | Timing Pulley:44t |
| Парткод: | B6524727 |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 04504008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 04503008N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 07200030E |
| Деталь: | Parallel Pin - 2x12 |
| Парткод: | 06320120G |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52062684 |
| Деталь: | Bracket:Paper Feed Sensor |
| Парткод: | B1324284 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW010118 |
| Деталь: | Guide Plate:Fusing Exit:L |
| Парткод: | B1324283 |
| Деталь: | Pressure Roller Cleaning |
| Парткод: | AE042069 |
| Деталь: | Holder:Lever: Pressure Rol |
| Парткод: | B1324255 |
| Деталь: | Bushing:Cleaning Roller:P |
| Парткод: | AE031060 |
| Деталь: | Bushing Cleaning Roller |
| Парткод: | AE031059 |
| Деталь: | Harness:Fusing Unit:No.1: |
| Парткод: | B1325204 |
| Деталь: | Screw - Inner Cover |
| Парткод: | B0045843 |
| Деталь: | Pressure Spring Holder |
| Парткод: | A0304145 |
| Деталь: | Stripper Pawls:Assy |
| Парткод: | B1324290 |
| Деталь: | Terminal : 4P :187 |
| Парткод: | AA113037 |
| Деталь: | Bracket :Drawer |
| Парткод: | B1324244 |
| Деталь: | SPRING |
| Парткод: | G0035674 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | AE020152 |
| Деталь: | Gear:48Z |
| Парткод: | AB013764 |
| Деталь: | BALL BEARING |
| Парткод: | AE030040 |
| Деталь: | Heater Holder:Lower |
| Парткод: | B1324245 |
| Деталь: | Lever: Pressure |
| Парткод: | B1324233 |
| Деталь: | Holder: Spring :Rear |
| Парткод: | B1324230 |
| Деталь: | Lever:Release |
| Парткод: | B1324238 |
| Деталь: | Lever: Turn |
| Парткод: | B1324232 |
| Деталь: | Compression Spring:Pressu |
| Парткод: | B1324192 |
| Деталь: | Side Plate:Lower Rear |
| Парткод: | B1324201 |
| Деталь: | Tension Spring:Heat Rolle |
| Парткод: | B1324193 |
| Деталь: | Stay:Lower |
| Парткод: | B1324203 |
| Деталь: | Stay:Right Lower |
| Парткод: | B1324204 |
| Деталь: | Housing : Thermostat |
| Парткод: | B1324148 |
| Деталь: | Side Plate:Lower Front |
| Парткод: | B1324202 |
| Деталь: | Holder: Spring : Front |
| Парткод: | B1324231 |
| Деталь: | Harness:Thermostat:Lower |
| Парткод: | B1324249 |
| Деталь: | Bracket : Connector |
| Парткод: | B1324246 |
| Деталь: | Bracket Pressure Roller C |
| Парткод: | B1324250 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | B1324199 |
| Деталь: | Screw - M3x8 |
| Парткод: | 09543008N |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 07200030E |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 03530060N |
| Деталь: | Hexagonal Head Bolt:M5x16 |
| Парткод: | 05850161N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Screw M4x12 |
| Парткод: | 03540120N |
| Деталь: | Screw - M3X6 |
| Парткод: | 09543006N |
| Деталь: | Imaging Unit |
| Парткод: | B1321952 |
| Деталь: | PCB:Sync Detector Board:S |
| Парткод: | B1325185 |
| Деталь: | Door Stopper |
| Парткод: | A2591258 |
| Деталь: | Decal - LD 655 |
| Парткод: | AA000217 |
| Деталь: | Cover:Polygon Motor:Assy |
| Парткод: | B1322185 |
| Деталь: | Polygon Motor |
| Парткод: | B1322156 |
| Деталь: | Positioning Pin |
| Парткод: | B1321971 |
| Деталь: | Harness: LDB: LDD |
| Парткод: | B1325366 |
| Деталь: | Cover:Upper: Sub-ass y |
| Парткод: | B1322172 |
| Деталь: | Harness:Imaging Unit |
| Парткод: | B1325226 |
| Деталь: | Shield:Shield Glass |
| Парткод: | B1322085 |
| Деталь: | Grip:Shield Glass |
| Парткод: | B1322094 |
| Деталь: | Shield Glass |
| Парткод: | AC015041 |
| Деталь: | Rail:Shield Glass |
| Парткод: | B1322093 |
| Деталь: | Thermistor Plate |
| Парткод: | G0601908 |
| Деталь: | Thermistor:Imaging Unit |
| Парткод: | AW100100 |
| Деталь: | Cable: LVDS: LDB |
| Парткод: | B1325367 |
| Деталь: | Screw:M4x20 |
| Парткод: | 03540200N |
| Деталь: | Screw:M4x8 |
| Парткод: | 03540080N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 03530060N |
| Деталь: | Tapping Screw - 4x6 |
| Парткод: | 04514006N |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA082104 |
| Деталь: | Cam:On-Off |
| Парткод: | B1326111 |
| Деталь: | Shaft:Cam:Color |
| Парткод: | B1326112 |
| Деталь: | Shaft:Positioning |
| Парткод: | B1326094 |
| Деталь: | Roller:Opposed:Belt Clean |
| Парткод: | B1326065 |
| Деталь: | Roller:Opposed |
| Парткод: | B1326073 |
| Деталь: | Roller:Transfer:Front |
| Парткод: | B1326069 |
| Деталь: | Roller:Drive |
| Парткод: | B1326055 |
| Деталь: | Shaft:Cam |
| Парткод: | B1326113 |
| Деталь: | Cam:On-Off:Black |
| Парткод: | B1326114 |
| Деталь: | Gear:16z |
| Парткод: | B1326130 |
| Деталь: | Holder: Opposed:Rear: Assy |
| Парткод: | B1326150 |
| Деталь: | Joint: Transfer: Drive |
| Парткод: | B1326099 |
| Деталь: | Holder:Opposed:Transfer:F |
| Парткод: | B1326143 |
| Деталь: | Grip:On-Off |
| Парткод: | B1326132 |
| Деталь: | Joint: Intermediate Transf |
| Парткод: | B1326175 |
| Деталь: | Compression Spring:Plate: |
| Парткод: | B1326136 |
| Деталь: | Plate:Intermediate Transf |
| Парткод: | B1326134 |
| Деталь: | Screw - M3X6 |
| Парткод: | 03603006N |
| Деталь: | Screw:M4x16 |
| Парткод: | 03604016N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Retaining Ring - M8 |
| Парткод: | 07200080E |
| Деталь: | Bushing 8mm |
| Парткод: | 8053511 |
| Деталь: | Ball Bearing:10x22x6 |
| Парткод: | 7423910 |
| Деталь: | Ball Bearing - 6x10x3 |
| Парткод: | 8053496 |
| Деталь: | Stabilizer |
| Парткод: | B1321891 |
| Деталь: | Bracket:Invertor |
| Парткод: | B1321851 |
| Деталь: | Bracket: Fan:MM4 0: Invertor |
| Парткод: | B1321852 |
| Деталь: | Fan Motor:15mm:24V |
| Парткод: | AX640164 |
| Деталь: | Screw:6x1.7 |
| Парткод: | AA143802 |
| Деталь: | Pulley:Tension:Timing Bel |
| Парткод: | B1321710 |
| Деталь: | Bracket:Motor |
| Парткод: | B1321702 |
| Деталь: | PRESSURE SPRING |
| Парткод: | G0294150 |
| Деталь: | Cushion - Stepper Motor |
| Парткод: | A1341724 |
| Деталь: | Stepper Motor:Scanner |
| Парткод: | B1321703 |
| Деталь: | Cover: Damper |
| Парткод: | B1321714 |
| Деталь: | Cover:Shaft |
| Парткод: | B1321716 |
| Деталь: | Drive Were:Scanner |
| Парткод: | B1321729 |
| Деталь: | Bracket:Tension |
| Парткод: | B1321724 |
| Деталь: | Bracket:Tension:Fix |
| Парткод: | B1321725 |
| Деталь: | Spring:Drive Were |
| Парткод: | B1321723 |
| Деталь: | Timing Belt:100S2M266 |
| Парткод: | AA043314 |
| Деталь: | Pulley:40T |
| Парткод: | B1321720 |
| Деталь: | PULLEY |
| Парткод: | AB032070 |
| Деталь: | Screw:Mechanical Drive Se |
| Парткод: | B1321719 |
| Деталь: | Harness:SIOB:SBU |
| Парткод: | B1325301 |
| Деталь: | Harness:SIOB:Fan Motor |
| Парткод: | B1325302 |
| Деталь: | Harness:SIOB:Original Sen |
| Парткод: | B1325300 |
| Деталь: | PCB:SIOB |
| Парткод: | B1325495 |
| Деталь: | Bracket:Pulley |
| Парткод: | B1321671 |
| Деталь: | PULLEY |
| Парткод: | AB032069 |
| Деталь: | Cover:Polygon Mirror Moto |
| Парткод: | B1321675 |
| Деталь: | Fan Motor:Mm60 |
| Парткод: | AX640151 |
| Деталь: | Gasket:Cover:Shaft |
| Парткод: | B1321728 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Screw - M3X6 |
| Парткод: | 09513006N |
| Деталь: | Tapping Screw:Round Point |
| Парткод: | 8025291 |
| Деталь: | Tapping Screw:3x20 |
| Парткод: | 04513020N |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Screw - M4X12 |
| Парткод: | 03140120N |
| Деталь: | Screw - M4X8 |
| Парткод: | 09544008N |
| Деталь: | Tapping Screw:M4x25 |
| Парткод: | 04514025N |
| Деталь: | Ball Bearing - 8x16x5mm |
| Парткод: | 8053368 |
| Деталь: | Harness Clamp |
| Парткод: | 11050487 |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Harness Clamp |
| Парткод: | 11050488 |
| Деталь: | Edge Saddle - Les-1010 |
| Парткод: | 11050518 |
| Деталь: | Exit Roller:Exit:Drive |
| Парткод: | B1327086 |
| Деталь: | Roller:Middle |
| Парткод: | B1327087 |
| Деталь: | Guide Plate:Shaft:Assy |
| Парткод: | B1327151 |
| Деталь: | Roller:Middle:Duplex Sub- |
| Парткод: | B1327088 |
| Деталь: | Reverse Roller:Drive |
| Парткод: | B1327081 |
| Деталь: | Roller:Decura:Entrance |
| Парткод: | B1327161 |
| Деталь: | Roller:Decura:Exit |
| Парткод: | B1327085 |
| Деталь: | Washer M6 - Scanner Unit |
| Парткод: | H0531174 |
| Деталь: | Spring - Lower Exit Rolle |
| Парткод: | A4701704 |
| Деталь: | Shift Clutch |
| Парткод: | A4701703 |
| Деталь: | Pulley: 19Z |
| Парткод: | B1327051 |
| Деталь: | Timing Belt:T198 |
| Парткод: | B1327116 |
| Деталь: | Tightener:Front Upper:Ass |
| Парткод: | B1327112 |
| Деталь: | TENSION SPRING |
| Парткод: | AA060695 |
| Деталь: | Pulley:13T |
| Парткод: | B1327048 |
| Деталь: | Roller:Tightener |
| Парткод: | B1327025 |
| Деталь: | Bracket:Connector |
| Парткод: | B1327069 |
| Деталь: | Pulley:15T |
| Парткод: | B1327036 |
| Деталь: | Pulley:15T |
| Парткод: | B1327028 |
| Деталь: | Timing Belt:T213 |
| Парткод: | B1327117 |
| Деталь: | Roller:Tightener |
| Парткод: | B1327059 |
| Деталь: | Shaft:Base:Tightener |
| Парткод: | B1327141 |
| Деталь: | Pulley:37T |
| Парткод: | B1327080 |
| Деталь: | Spring:Tightener |
| Парткод: | B1327143 |
| Деталь: | Gear:Z20 |
| Парткод: | B1327138 |
| Деталь: | Gear:Z28 |
| Парткод: | B1327144 |
| Деталь: | Pulley:Z13 |
| Парткод: | B1327162 |
| Деталь: | Gear:Z27 |
| Парткод: | B1327030 |
| Деталь: | Gear:29Z |
| Парткод: | B1327060 |
| Деталь: | Gear:22Z |
| Парткод: | B1327055 |
| Деталь: | Stopper:Guide |
| Парткод: | B1327155 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Ball Bearing - 6x10x3 |
| Парткод: | 7413706 |
| Деталь: | Pin - 2x10mm |
| Парткод: | 06320100G |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Relay Connector - 2P |
| Парткод: | 11026245 |
| Деталь: | Registration Roller:Upper |
| Парткод: | B1322629 |
| Деталь: | Registration Roller:Lower |
| Парткод: | B1322617 |
| Деталь: | LED:Radiate |
| Парткод: | AX560011 |
| Деталь: | Harness: T .ED: Sensor |
| Парткод: | B1325246 |
| Деталь: | Bracket:Optics Sensor |
| Парткод: | B1322624 |
| Деталь: | Registration Guide:Lower |
| Парткод: | B1322610 |
| Деталь: | Ball Bearing - 8x12x5 |
| Парткод: | A2472800 |
| Деталь: | Spacer - 1x8x12 |
| Парткод: | AA132025 |
| Деталь: | Timing Pulley:35T |
| Парткод: | AB030302 |
| Деталь: | Pawl:Lock:Front |
| Парткод: | B1322708 |
| Деталь: | Bushing - 4x6x7mm |
| Парткод: | 54432668 |
| Деталь: | Shaft:Lock |
| Парткод: | B1322691 |
| Деталь: | Pawl:Lock:Rear |
| Парткод: | B1322692 |
| Деталь: | SPRING |
| Парткод: | AA066372 |
| Деталь: | Bushing - M8 |
| Парткод: | AA082116 |
| Деталь: | Roller: Connecting: Drive |
| Парткод: | B1322658 |
| Деталь: | Guide Plate:Entrance:Lowe |
| Парткод: | B1322790 |
| Деталь: | EXIT ROLLER SPRING |
| Парткод: | AA063433 |
| Деталь: | Bushing - 4x5x7 |
| Парткод: | AA080034 |
| Деталь: | Transport Roller:Driven:D |
| Парткод: | B1322675 |
| Деталь: | Front Bushing - Registrat |
| Парткод: | B1322724 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA062329 |
| Деталь: | Collar - 8mm |
| Парткод: | 54462901 |
| Деталь: | Cover:Harness:Pull Out |
| Парткод: | B1321232 |
| Деталь: | Rear Bushing - Registrati |
| Парткод: | B1322725 |
| Деталь: | Gear:50Z |
| Парткод: | AB011300 |
| Деталь: | Guide Plate:Open And Clos |
| Парткод: | B1322641 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 07200060E |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Retaining Ring - M2.5 |
| Парткод: | 07200025E |
| Деталь: | Ball Bearing - 8x16x5 |
| Парткод: | 7423808 |
| Деталь: | Parallel Pin - 3x16mm |
| Парткод: | 06330160G |
| Деталь: | CLAMP |
| Парткод: | 11050534 |
| Деталь: | Gear:32Z |
| Парткод: | AB011301 |
| Деталь: | Guard:Pull Out |
| Парткод: | B1321192 |
| Деталь: | Guide Plate:Paper Bank:As |
| Парткод: | B1322767 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA080203 |
| Деталь: | Transport Roller:Driven |
| Парткод: | B1322639 |
| Деталь: | Driven Roller Spring |
| Парткод: | AA063254 |
| Деталь: | Guide Plate:Connecting:Ri |
| Парткод: | B1322636 |
| Деталь: | HARNESS:SENSOR |
| Парткод: | B1325247 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW010107 |
| Деталь: | Bracket:Sensor |
| Парткод: | B1322773 |
| Деталь: | DC Solenoid:24V:16.5W:Ass |
| Парткод: | B1322594 |
| Деталь: | Arm:Guide |
| Парткод: | B1322649 |
| Деталь: | Arm:Perpendicular |
| Парткод: | B1322650 |
| Деталь: | Support Stay:Solenoid |
| Парткод: | B1322753 |
| Деталь: | Bracket:Solenoid |
| Парткод: | B1322661 |
| Деталь: | Rail:Solenoid:Release |
| Парткод: | B1322667 |
| Деталь: | Cover:Motor:Registration |
| Парткод: | B1322723 |
| Деталь: | Snap Ring |
| Парткод: | 52062686 |
| Деталь: | Bracket:Tightener |
| Парткод: | B1322720 |
| Деталь: | TENSION SPRING |
| Парткод: | B1322710 |
| Деталь: | Bracket:Stepper Motor |
| Парткод: | B1322711 |
| Деталь: | Timing Belt:60S2M138 |
| Парткод: | AA043312 |
| Деталь: | Stepper Motor:Registratio |
| Парткод: | B1322722 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW020145 |
| Деталь: | Bracket:Photointerruptor |
| Парткод: | B1321233 |
| Деталь: | Guide:Duplex:Upper Right |
| Парткод: | B1324868 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 03530060N |
| Деталь: | Screw - M3X4 |
| Парткод: | 03530040N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Retaining Ring - M2.5 |
| Парткод: | 07200025E |
| Деталь: | Harness Clamp - LWS-0306Z |
| Парткод: | 11050511 |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 11050522 |
| Деталь: | Clamp:LES-0505 |
| Парткод: | 11050551 |
| Деталь: | Clamp:Lwss-0504 |
| Парткод: | 11050568 |
| Деталь: | Relay Connector - 6P |
| Парткод: | 11026249 |
| Деталь: | Cover:Left Upper |
| Парткод: | B1321503 |
| Деталь: | Screw:M4:Dia5 |
| Парткод: | AA143559 |
| Деталь: | Exposure Glass:Sheet Thro |
| Парткод: | BC012007 |
| Деталь: | SEAL |
| Парткод: | B0651782 |
| Деталь: | Scale Bracket |
| Парткод: | B0651787 |
| Деталь: | Scale Bracket Seal |
| Парткод: | B0651773 |
| Деталь: | Bracket:Filter:Assy |
| Парткод: | B1321856 |
| Деталь: | Filter:Scanner |
| Парткод: | B1321864 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA143520 |
| Деталь: | Left Scale |
| Парткод: | B0651772 |
| Деталь: | Scale:Sheet Through (NA) |
| Парткод: | B1321687 |
| Деталь: | Exposure Glass |
| Парткод: | A2501752 |
| Деталь: | Scale:Rear:Printing |
| Парткод: | B1321692 |
| Деталь: | Bracket:ADF |
| Парткод: | B1321885 |
| Деталь: | Decal - Copy:Original |
| Парткод: | B1321583 |
| Деталь: | Cover:Right Upper |
| Парткод: | B1321502 |
| Деталь: | RIGHT STAY |
| Парткод: | B0651785 |
| Деталь: | Spring Plate:Ground Plate |
| Парткод: | B1321898 |
| Деталь: | Mylar:Frame:Front |
| Парткод: | B1321683 |
| Деталь: | Mylar:Frame :Middle |
| Парткод: | B1321684 |
| Деталь: | Mylar:Frame:Rear |
| Парткод: | B1321685 |
| Деталь: | Exposure Glass Cushion |
| Парткод: | 54421924 |
| Деталь: | Cushion - 0.5 |
| Парткод: | AA161137 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 04513006N |
| Деталь: | Screw - M3X4 |
| Парткод: | 03530040N |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | Snap Ring |
| Парткод: | 54472681 |
| Деталь: | Guide Roller - B |
| Парткод: | A3002134 |
| Деталь: | Rail:Left:Assy |
| Парткод: | B1324835 |
| Деталь: | Rail:Right:Assy |
| Парткод: | B1324591 |
| Деталь: | Roller - Positioning Guid |
| Парткод: | 67542866 |
| Деталь: | Hexagonal Bolt:M12x35 |
| Парткод: | AA143798 |
| Деталь: | Heat Sink:Heater:Lower:NA |
| Парткод: | B1406225 |
| Деталь: | Cover: Temperature/Humidit |
| Парткод: | B1326579 |
| Деталь: | Guide:Tank:Discharge Used |
| Парткод: | B1326577 |
| Деталь: | Temperature & Humidity Se |
| Парткод: | AW140012 |
| Деталь: | Caster:1470n |
| Парткод: | AH012031 |
| Деталь: | Flanged Hexagonal Head Bo |
| Парткод: | AA143803 |
| Деталь: | Harness:Duplex:Fan:Middle |
| Парткод: | B1325266 |
| Деталь: | Fan Motor:MM80 |
| Парткод: | AX640163 |
| Деталь: | Bracket:Fan:Duplex |
| Парткод: | B1321118 |
| Деталь: | Cushion - Motor |
| Парткод: | AA161104 |
| Деталь: | PAPER GUIDE SHEET |
| Парткод: | A0966693 |
| Деталь: | BRACKET |
| Парткод: | B0651092 |
| Деталь: | Bracket:Holder:Assy |
| Парткод: | B1324830 |
| Деталь: | Tapping Screw:4x8 |
| Парткод: | 04514008N |
| Деталь: | Screw - M3X6 |
| Парткод: | 03130060N |
| Деталь: | Pan Self-tapping Screw:M4 |
| Парткод: | 04340080N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 07200040E |
| Деталь: | Screw:M4x20 |
| Парткод: | 03540200N |
| Деталь: | Bushing - 4x5 |
| Парткод: | 07074050N |
| Деталь: | Screw: Pol ished Round: M4x1 |
| Парткод: | 09514010N |
| Деталь: | CLAMP |
| Парткод: | 11050516 |
| Деталь: | Harness Clamp - LWS-0711 |
| Парткод: | 11050508 |
Коды ошибок
SC101
SC120
SC121
SC141
SC142
SC144
SC161
SC180-001
SC180-002
SC195
SC202
SC203
SC204
SC205
SC210
SC211
SC212
SC213
SC220
SC221
SC222
SC223
SC224
SC225
SC226
SC227
SC230
SC231
SC232
SC233
SC234
SC235
SC236
SC237
SC240
SC241
SC242
SC243
SC268
SC269
SC270
SC271
SC272
SC285
SC300
SC301
SC302
SC303
SC312
SC313
SC314
SC315
SC316
SC317
SC318
SC319
SC320
SC321
SC322
SC323
SC324
SC325
SC326
SC327
SC336
SC337
SC338
SC339
SC340
SC341
SC342
SC343
SC348
SC360
SC361
SC362
SC363
SC364
SC365
SC366
SC367
SC372
SC373
SC374
SC375
SC396
SC397
SC398
SC399
SC400
SC410
SC411
SC412
SC413
SC414
SC415
SC416
SC417
SC418
SC420
SC421
SC422
SC423
SC424
SC425
SC426
SC427
SC432
SC433
SC434
SC435
SC436
SC437
SC438
SC439
SC440
SC441
SC442
SC443
SC445
SC446
SC450
SC455
SC460
SC484
SC485
SC487
SC488
SC490
SC496
SC497
SC498
SC499
SC501
SC502
SC503
SC504
SC505
SC506
SC510
SC515
SC516
SC520
SC530
SC531
SC532
SC533
SC534
SC535
SC541
SC542
SC543
SC544
SC545
SC546
SC547
SC548
SC549
SC550
SC551
SC552
SC553
SC554
SC555
SC556
SC561
SC562
SC563
SC564
SC565
SC585
SC620
SC621
SC622
SC624
SC630
SC632
SC633
SC634
SC635
SC670
SC672
SC680
SC687
SC701
SC705
SC720
SC721
SC723
SC724
SC725
SC726
SC727
SC728
SC730
SC740
SC741
SC742
SC743
SC744
SC750
SC751
SC752
SC753
SC760
SC761
SC762
SC763
SC764
SC765
SC766
SC767
SC770
SC775
SC780
SC781
SC782
SC790
SC817
SC818
SC819
SC821-0B00
SC821-0B06
SC821-0B10
SC822-3003
SC822-3004
SC822-3013
SC822-3014
SC824
SC826-1501
SC826-15FE
SC828
SC833
SC834
SC850
SC851
SC853
SC854
SC855
SC856
SC857
SC860
SC861
SC863
SC864
SC865
SC866
SC867
SC868
SC870
SC873
SC874
SC875
SC880
SC900
SC910
SC911
SC912
SC913
SC914
SC919
SC920
SC921
SC925
SC990
SC991
SC992
SC997
SC998
Описание
| Error code: | SC101 |
| Description: | Exposure lamp error The white level peak did not reach the prescribed threshold when the white plate was scanned. |
| Causes: | The scanner has scanned the white plate, but cannot detect the certain white level. • Defective exposure lamp • Defective exposure lamp stabilizer • Defective power source harness • Defective signal harness • High-voltage cable leak • Defective darkness starting characteristic |
| Remedy: | • Dirty optics • Exposure lamp defective • Exposure lamp does not turn ON • Lamp stabilizer defective • High voltage line leak • Power/signal harness defective |
| Error code: | SC120 |
| Description: | Scanner home position error 1 The scanner home position sensor did not detect the home position (did not go OFF) after the scanner moved forward 20 mm.. |
| Causes: | The scanner home position sensor does not detect the scanner leaving the home position. • Defective scanner home position sensor • Defective scanner home position sensor harness • Defective scanner motor driver • Defective scanner motor |
| Remedy: | • Scanner motor driver board defective • Scanner motor defective • Scanner HP sensor defective • Harness between scanner motor and scanner I/O board disconnected or broken. |
| Error code: | SC121 |
| Description: | Scanner home position error 2 The scanner home position sensor did not go ON after the scanner moved forward 1 mm and the feeler entered the HP sensor. |
| Causes: | The scanner home position sensor does not detect the scanner coming back to the home position. • Defective scanner home position sensor • Defective scanner home position sensor harness • Defective scanner motor driver • Defective scanner motor |
| Remedy: | • Scanner motor defective • Scanner HP sensor disconnected, defective |
| Error code: | SC141 |
| Description: | Black level detection error During AGC the value for black level was not within ±2 of the prescribed value. The copier can reproduce monochrome, but not color. |
| Causes: | The automatic adjustment has failed to correct the black level to the permissible range. • Defective SBU board • Defective harness |
| Remedy: | • SBU defective • Harness defective |
| Error code: | SC142 |
| Description: | White level detection error During AGC the value for white level was not within ±7 of the prescribed value. |
| Causes: | The automatic adjustment has failed to correct the white level to the permissible range. • Defective scanner drive • Defective optical section • Defective SBU board • Defective harness |
| Remedy: | • Exposure lamp defective • Harness disconnected, damaged • Dirty exposure glass, optics • Scanner motor, drive assembly defective • SBU board defective |
| Error code: | SC144 |
| Description: | SBU (Sensor Board Unit) communication error When the machine is switched ON, or when the machine returns to full operation from the energy save mode, the machine can not access the SBU register, or the SBU register values are abnormal. |
| Causes: | Cannot correctly establish communication with the SBU. • Defective harness • Defective destination device (e.g., BICU, etc) • Defective SBU |
| Remedy: | • Dirty exposure glass or optics • SBU board defective • SBU harness disconnected, defective |
| Error code: | SC161 |
| Description: | IDU (Image Discrimination Unit) error After the command is written into the DFID self-diagnosis startup register, the correct value is not stored in the register for the prescribed length of time after power ON. -or- After the negate interruption of FGATE occurs, IDU is not recognized within the prescribed time during scanning. |
| Causes: | • Check harness connections between SBU and IPU/VBCU • IPU defective • VBCU defective |
| Remedy: | • IPU board defective (defective connection between ASIC and DFID, defective LSYNC-signal) |
| Error code: | SC180-001 |
| Description: | Scanner fan lock One of the fan motors next to the exposure lamp did not switch ON within 0.5 sec after the CPU issued the ON signal. |
| Remedy: | • Fan defective • Foreign object interfering with operation of fan • Motor harness loose, disconnected, or broken • SIOB defective • SBU defective |
| Error code: | SC180-002 |
| Description: | Scanner fan lock The scanner fan motor next to the SIOB did not switch ON within 0.5 sec. after the CPU issued the ON signal. |
| Remedy: | • Fan defective • Foreign object interfering with operation of fan • Motor harness loose, disconnected, or broken • SIOB defective • SBU defective |
| Error code: | SC195 |
| Description: | Machine serial number error The number registered for the machine serial number does not match. |
| Causes: | Comparison of the product identification code in the machine serial number (11 digits). The product identification code in the machine serial number (11 digits) does not match. |
| Remedy: | • Confirm the correct serial number of the machine in the specifications Important! WHEN SC195 OCCURS, THE SERIAL NUMBER MUST BE INPUT. PLEASE CONTACT YOUR TECHNICAL SUPERVISOR. |
| Error code: | SC202 |
| Description: | Polygon motor error 1: ON timeout The polygon mirror motor does not reach the targeted operating speed: • Within 10 seconds after turning ON. • Within 10 sec. after changing speed |
| Causes: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective |
| Remedy: | • Harness to polygon motor driver board disconnected, defective • Polygon motor defective • Polygon motor driver board defective • Polygon motor defective. |
| Error code: | SC203 |
| Description: | Polygon motor error 2: OFF timeout The polygon mirror motor does leave the READY status within 10 seconds after the polygon motor switches OFF. |
| Causes: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective |
| Remedy: | • Harness to polygon motor driver board disconnected, defective • Polygon motor defective • Polygon motor driver board defective • Polygon motor defective. |
| Error code: | SC204 |
| Description: | Polygon motor error 3: Polygon motor lock signal error The polygon motor lock signal goes HIGH (inactive) while the laser diode is firing. |
| Causes: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective |
| Remedy: | • Harness to polygon motor driver board disconnected, defective • Polygon motor defective • Polygon motor driver board defective |
| Error code: | SC205 |
| Description: | Polygon motor error 4: Polygon motor lock signal unstable When the polygon motor switches ON, or after the speed of the motor changes, the polygon motor lock signal goes HIGH (inactive). |
| Causes: | • Switch the machine off/on (problem was probably due to electronic noise) • Replace the harness if cycling the machine off/on does not solve the problem • Polygon motor defective • Polygon mirror motor control board defective • IPU defective |
| Remedy: | • Harness to polygon motor driver board disconnected, defective • Polygon motor defective • Polygon motor driver board defective |
| Error code: | SC210 |
| Description: | Laser beam detection error 1: K (Black) The laser synchronization sensor failed to detect the beginning and end of the laser beam flash for the designated color onto the polygon mirror while the mirror is rotating at the prescribed number of revolutions. |
| Causes: | • Cycle the machine off/on • CK Laser unit defective |
| Remedy: | • Laser synchronization detector sensor connection loose, not connected • Laser synchronization detector sensor defective |
| Error code: | SC211 |
| Description: | Laser beam detection error 1: Y (Yellow) The laser synchronization sensor failed to detect the beginning and end of the laser beam flash for the designated color onto the polygon mirror while the mirror is rotating at the prescribed number of revolutions. |
| Causes: | • Cycle the machine off/on • CK laser unit defective |
| Remedy: | • Laser synchronization detector sensor connection loose, not connected • Laser synchronization detector sensor defective |
| Error code: | SC212 |
| Description: | Laser beam detection error 1: M (Magenta) The laser synchronization sensor failed to detect the beginning and end of the laser beam flash for the designated color onto the polygon mirror while the mirror is rotating at the prescribed number of revolutions. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • Laser synchronization detector sensor connection loose, not connected • Laser synchronization detector sensor defective |
| Error code: | SC213 |
| Description: | Laser beam detection error 1: C (Cyan) The laser synchronization sensor failed to detect the beginning and end of the laser beam flash for the designated color onto the polygon mirror while the mirror is rotating at the prescribed number of revolutions. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • Laser synchronization detector sensor connection loose, not connected • Laser synchronization detector sensor defective |
| Error code: | SC220 |
| Description: | Laser Synchronization Detector Error 1: K Leading Edge: LD0 While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 black, or leading edge, even after the laser diode has been firing for 2 sec. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • Beam not reflected in photo detection • GAVD (ASIC) on the BICU is defective • LD driver board defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC221 |
| Description: | Laser Synchronization Detector Error 2: K Leading Edge (Other than LD0) While the polygon motor is rotating normally, no synchronizing detection signal is output for black, leading edge for any LD other than LD0, even after the laser diode has been firing for 2 sec. |
| Causes: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Check all connections between LD unit, LDB, IPU • LD unit • LDB defective • IPU defective |
| Remedy: | • Beam not reflected in photo detection • GAVD (ASIC) (ASIC) on the BICU defective • LD driver defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC222 |
| Description: | Laser Synchronization Detector Error 1: Y Leading Edge: LD0 While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 yellow, leading edge, even after the laser diode has been firing for 2 sec. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • Beam not reflected in photo detection • GAVD (ASIC) (ASIC) on the BICU defective • LD driver board defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC223 |
| Description: | Laser Synchronization Detector Error 2: Y Leading Edge (Other than LD0) While the polygon motor is rotating normally, no synchronizing detection signal is output for yellow, leading edgefor any LD other than LD0, even after the laser diode has been firing for 2 sec. |
| Causes: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Check all connections between LD unit, LDB, IPU • LD unit • LDB defective • IPU defective |
| Remedy: | • Beam not reflected in photo detection • GAVD (ASIC) (ASIC) on the BICU defective • LD driver defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC224 |
| Description: | Laser Synchronization Detector Error 1: M Leading Edge: LD0 While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 magenta, leading edge, even after the laser diode has been firing for 2 sec. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • Beam not reflected in photo detection • GAVD (ASIC) on the BICU defective • LD driver board defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC225 |
| Description: | Laser Synchronization Detector Error 2: M Leading Edge (Other than LD0) While the polygon motor is rotating normally, no synchronizing detection signal is output for magenta, leading edge for any LD other than LD0, even after the laser diode has been firing for 2 sec. |
| Causes: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Check all connections between LD unit, LDB, IPU • LD unit • LDB defective • IPU defective |
| Remedy: | • Beam not reflected in photo detection • GAVD (ASIC) on the BICU defective • LD driver defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC226 |
| Description: | Laser Synchronization Detector Error 1: C Leading Edge: LD0 While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 cyan, leading edge, even after the laser diode has been firing for 2 sec. |
| Causes: | • Cycle the machine off/on • YM Laser unit defective |
| Remedy: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • Beam not reflected in photo detection • GAVD (ASIC) on the BICU defective • LD driver board defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC227 |
| Description: | Laser Synchronization Detector Error 2: C Leading Edge (Other than LD0) While the polygon motor is rotating normally, no synchronizing detection signal is output for cyan, leading edgefor any LD other than LD0, even after the laser diode has been firing for 2 sec. |
| Causes: | • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Check all connections between LD unit, LDB, IPU • LD unit • LDB defective • IPU defective |
| Remedy: | • Beam not reflected in photo detection • GAVD (ASIC) on the BICU defective • LD driver defective • LDB defective • BICU defective • Check board connections, replace |
| Error code: | SC230 |
| Description: | FGATE error 1: Feedback remains HIGH for K write After the start of timing to create the black image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received no feedback (LOW signal) from the LD unit to indicate that the lasers started firing at the prescribed time to create the patterns. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK Laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Controller board disconnected, defective • Harness between the BICU and LDB unit disconnected, loose, or defective. • Check board connections, replace |
| Error code: | SC231 |
| Description: | FGATE error 1: Feedback remains LOW for K write After the start of timing to create the black image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received a LOW feedback signal, but the signal remained LOW (indicating the lasers were still operating), even after creation of the next image should have started. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK Laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Check board connections, replace |
| Error code: | SC232 |
| Description: | FGATE error 1: Feedback remains HIGH for Y write After the start of timing to create the yellow image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received no feedback (LOW signal) from the LD unit to indicate that the lasers started firing at the prescribed time to create the patterns. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK Laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Controller board disconnected, defective • Harness between the BICU and LDB unit disconnected, loose, or defective. • Check board connections, replace |
| Error code: | SC233 |
| Description: | FGATE error 1: Feedback remains LOW for Y write. After the start of timing to create the yellow image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received a LOW feedback signal, but the signal remained LOW (indicating the lasers were still operating), even after creation of the next image should have started. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK Laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Check board connections, replace |
| Error code: | SC234 |
| Description: | FGATE error 1: Feedback remains HIGH for M write. After the start of timing to create the magenta image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received no feedback (LOW signal) from the LD unit to indicate that the lasers started firing at the prescribed time to create the patterns. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • YM laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Controller board disconnected, defective • Harness between the BICU LDB unit disconnected, loose, or defective. • Check board connections, replace |
| Error code: | SC235 |
| Description: | FGATE error 1: Feedback remains LOW for M write. After the start of timing to create the magenta image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received a LOW feedback signal, but the signal remained LOW (indicating the lasers were still operating), even after creation of the next image should have started. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • YM laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Check board connections, replace |
| Error code: | SC236 |
| Description: | FGATE error 1: Feedback remains HIGH for C write. After the start of timing to create the cyan image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received no feedback (LOW signal) from the LD unit to indicate that the lasers started firing at the prescribed time to create the patterns. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • YM laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Controller board disconnected, defective • Harness between the BICU and LDB unit disconnected, loose, or defective. • Check board connections, replace |
| Error code: | SC237 |
| Description: | FGATE error 1: Feedback remains LOW for C write. After the start of timing to create the cyan image, the PFGATE register of the GAVD (ASIC) does not assert, even after 5 sec. when: • Images are created on the drum. • MUSIC patterns are created on the transfer belt. The BICU received a LOW feedback signal, but the signal remained LOW (indicating the lasers were still operating), even after creation of the next image should have started. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • YM laser unit defective |
| Remedy: | • GAVD (ASIC) on the BICU defective • PCI I/F on the IPU defective • ASIC on the IOB defective • Check board connections, replace |
| Error code: | SC240 |
| Description: | LD error 1: K An error is asserted at the LD error terminal of the black, yellow, magenta, or cyan LD driver after initialization of the LD because the power to the LD was higher or lower than the prescribed limit. |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD. |
| Remedy: | • LD defective due to wear, damage, short circuit • LDB harness disconnected, loose or defective |
| Error code: | SC241 |
| Description: | LD error 1: Y An error is asserted at the LD error terminal of the black, yellow, magenta, or cyan LD driver after initialization of the LD because the power to the LD was higher or lower than the prescribed limit. |
| Causes: | • Cycle the machine off/on • CK laser unit defective |
| Remedy: | • LD defective due to wear, damage, short circuit • LDB harness disconnected, loose or defective |
| Error code: | SC242 |
| Description: | LD error 1: M An error is asserted at the LD error terminal of the black, yellow, magenta, or cyan LD driver after initialization of the LD because the power to the LD was higher or lower than the prescribed limit. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • LD defective due to wear, damage, short circuit • LDB harness disconnected, loose or defective |
| Error code: | SC243 |
| Description: | LD error 1: C An error is asserted at the LD error terminal of the black, yellow, magenta, or cyan LD driver after initialization of the LD because the power to the LD was higher or lower than the prescribed limit. |
| Causes: | • Cycle the machine off/on • YM laser unit defective |
| Remedy: | • LD defective due to wear, damage, short circuit • LDB harness disconnected, loose or defective |
| Error code: | SC268 |
| Description: | Optical unit sensor error. At power ON, one of the two temperature sensors in the optics unit detected a temperature lower than 0°C for more than 1 sec. -or- It detected a temperature higher than 100°C for more than 1 sec. |
| Causes: | After the main power switch ON, writing thermistor temperature is detected at 100ms intervals an ... • Less than -30 degrees Celsius is detected for more than 4 seconds (Thermistor defective). • More than 105 degrees Celsius is detected for more than 1 second (Thermistor short). |
| Remedy: | • Thermistor disconnected (causes extremely low temperature reading) • Thermistor damaged and short circuited (causes extremely high temperature reading) • BICU defective |
| Error code: | SC269 |
| Description: | Exposure thermistor 2 error. At power on, exposure thermistor 2 detected a temperature lower than 0°C for more than 1 sec. -or- It detected a temperature higher than 100°C for more than 1 sec. |
| Causes: | • Thermistor disconnected (causes extremely low temperature reading) • Thermistor damaged and short circuited (causes extremely high temperature reading) • BCU defective |
| Remedy: | • Thermistor disconnected (causes extremely low temperature reading) • Thermistor damaged and short circuited (causes extremely high temperature reading) • BICU defective |
| Error code: | SC270 |
| Description: | Mirror motor upper/lower limit: Y (Yellow) The pulse rate of the mirror motor reaches the upper or lower limit. Note: SP2182 displays the pulse rate for each motor. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK laser unit defective |
| Remedy: | • 3rd mirror motor is defective. • 3rd mirror motor connecter is not connected correctly. |
| Error code: | SC271 |
| Description: | Mirror motor upper/lower limit: M (Magenta) The pulse rate of the mirror motor reaches the upper or lower limit. Note: SP2182 displays the pulse rate for each motor. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • CK laser unit defective |
| Remedy: | • 3rd mirror motor is defective. • 3rd mirror motor connecter is not connected correctly. |
| Error code: | SC272 |
| Description: | Mirror motor upper/lower limit: C (Cyan) The pulse rate of the mirror motor reaches the upper or lower limit. Note: SP2182 displays the pulse rate for each motor. |
| Causes: | • Cycle the machine off/on • IPU harness loose, disconnected, broken, defective • IPU defective • YM laser unit defective |
| Remedy: | • 3rd mirror motor is defective. • 3rd mirror motor connecter is not connected correctly. |
| Error code: | SC285 |
| Description: | MUSIC error. An error with the MUSIC occurs four times since the last time the main power was turned ON. |
| Causes: | • A PCDU is set incorrectly • ITB is set incorrectly • Execute manual process control with SP3011-2 (Density Adjustment) • MUSIC sensor harness loose, disconnected, broken, defective • MUSIC sensor defective • ITB damaged • Laser unit defective |
| Remedy: | • ITB defective • MUSIC sensors are dirty • MUSIC sensors are defective |
| Error code: | SC300 |
| Description: | AC charge output error 1: K An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the AC charge for black, magenta, cyan, or yellow (V = 0, for example) for 500 ms (250 times). |
| Causes: | • Disconnected or defective high voltage harness • Defective high voltage power supply • Defective EGB |
| Remedy: | • High voltage power supply • BICU defective • OPC unit defective 1. Disconnect the high voltage cable from Terminal C of the multiple highvoltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is nearly "0", check the highvoltage harness for defects and replace it if necessary. 4. Test the conductivity between the OPC unit and the ground. If there is no conductivity between the OPC unit and ground, replace the OPC unit. 5. If there is no charge PWM signal, replace the harness and/or BICU. |
| Error code: | SC301 |
| Description: | AC charge output error 2: M An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the AC charge for black, magenta, cyan, or yellow (V = 0, for example) for 500 ms (250 times). |
| Causes: | • Disconnect the high voltage cable from Terminal C of the power pack. • Attach a voltmeter to the terminal. • If there is no output from the terminal, replace the power pack. -or- • If there is output from the terminal, test the resistance between the high voltage cable and the ground. • If resistance is nearly "0", check the high-voltage harness for defects and replace it if necessary. • Test the conductivity between the PCU and the ground. If there is no conductivity between the PCU and ground, replace the PCU. • If there is no charge PWM signal, replace the harness and/or BCU. |
| Remedy: | • High voltage power supply • BICU defective • OPC unit defective 1. Disconnect the high voltage cable from Terminal C of the multiple highvoltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is nearly "0", check the highvoltage harness for defects and replace it if necessary. 4. Test the conductivity between the OPC unit and the ground. If there is no conductivity between the OPC unit and ground, replace the OPC unit. 5. If there is no charge PWM signal, replace the harness and/or BICU. |
| Error code: | SC302 |
| Description: | AC charge output error 3: C An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the AC charge for black, magenta, cyan, or yellow (V = 0, for example) for 500 ms (250 times). |
| Causes: | This SC is issued if the BICU detects a short in the power pack 10 times consecutively. Open circuit (+) / Short circuit (-) |
| Remedy: | • High voltage power supply • BICU defective • OPC unit defective 1. Disconnect the high voltage cable from Terminal C of the multiple highvoltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is nearly "0", check the highvoltage harness for defects and replace it if necessary. 4. Test the conductivity between the OPC unit and the ground. If there is no conductivity between the OPC unit and ground, replace the OPC unit. 5. If there is no charge PWM signal, replace the harness and/or BICU. |
| Error code: | SC303 |
| Description: | AC charge output error 4: Y An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the AC charge for black, magenta, cyan, or yellow (V = 0, for example) for 500 ms (250 times). |
| Causes: | • Disconnect the high voltage cable from Terminal C of the power pack. • Attach a voltmeter to the terminal. • If there is no output from the terminal, replace the power pack. -or- • If there is output from the terminal, test the resistance between the high voltage cable and the ground. • If resistance is nearly "0", check the high-voltage harness for defects and replace it if necessary. • Test the conductivity between the PCU and the ground. If there is no conductivity between the PCU and ground, replace the PCU. • If there is no charge PWM signal, replace the harness and/or BCU. |
| Remedy: | • High voltage power supply • BICU defective • OPC unit defective 1. Disconnect the high voltage cable from Terminal C of the multiple highvoltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is nearly "0", check the highvoltage harness for defects and replace it if necessary. 4. Test the conductivity between the OPC unit and the ground. If there is no conductivity between the OPC unit and ground, replace the OPC unit. 5. If there is no charge PWM signal, replace the harness and/or BICU. |
| Error code: | SC312 |
| Description: | Charge, development error 1: K 500 ms after the black, magenta, cyan, and yellow drums start to rotate, the machine starts to monitor the AC current feedback at 8 ms intervals. This is SC is issued if the feedback for the charge unit of any color drops below 0.5V for 400 ms (50 consecutive readings). |
| Causes: | • Pre-charge unit set incorrectly. • Pre-charge unit contact is broken or defective. |
| Remedy: | • Make sure that the settings of SP2202 are at the defaults. • Defective charge roller • Defective power pack |
| Error code: | SC313 |
| Description: | Charge, development error 2: M 500 ms after the black, magenta, cyan, and yellow drums start to rotate, the machine starts to monitor the AC current feedback at 8 ms intervals. This is SC is issued if the feedback for the charge unit of any color drops below 0.5V for 400 ms (50 consecutive readings). |
| Causes: | • Make sure that the settings of SP2202 are at the defaults. • Check harness connections between charge roller and transfer power pack. • Defective charge roller • Defective power pack |
| Remedy: | • Make sure that the settings of SP2202 are at the defaults. • Defective charge roller • Defective power pack |
| Error code: | SC314 |
| Description: | Charge, development error 3: C 500 ms after the black, magenta, cyan, and yellow drums start to rotate, the machine starts to monitor the AC current feedback at 8 ms intervals. This is SC is issued if the feedback for the charge unit of any color drops below 0.5V for 400 ms (50 consecutive readings). |
| Causes: | • Make sure that the settings of SP2202 are at the defaults. • Check harness connections between charge roller and transfer power pack. • Defective charge roller • Defective power pack |
| Remedy: | • Make sure that the settings of SP2202 are at the defaults. • Defective charge roller • Defective power pack |
| Error code: | SC315 |
| Description: | Charge, development error 4: Y 500 ms after the black, magenta, cyan, and yellow drums start to rotate, the machine starts to monitor the AC current feedback at 8 ms intervals. This is SC is issued if the feedback for the charge unit of any color drops below 0.5V for 400 ms (50 consecutive readings). |
| Causes: | • Make sure that the settings of SP2202 are at the defaults. • Check harness connections between charge roller and transfer power pack. • Defective charge roller • Defective power pack |
| Remedy: | • Make sure that the settings of SP2202 are at the defaults. • Defective charge roller • Defective power pack |
| Error code: | SC316 |
| Description: | AC bias charge adjustment error 1: K An average value of 8 ms/cycle could not be attained for Vpp (AC charge bias) within 15 attempts. -or- The output of the AC charge boosted Vpp over 2.8 kV. |
| Causes: | • Check the connections of the charge unit of the PCU where the problem occurred. • Replace the charge unit of the PCU (CBG power pack for the K PCU, charge roller unit for YMC PCUs) |
| Remedy: | • Charge roller dirty • Charge roller defective • Bias terminal connection at the PCU receptacle is dirty or defective |
| Error code: | SC317 |
| Description: | AC bias charge adjustment error 2: M An average value of 8 ms/cycle could not be attained for Vpp (AC charge bias) within 15 attempts. -or- The output of the AC charge boosted Vpp over 2.8 kV. |
| Causes: | • Check the connections of the charge unit of the PCU where the problem occurred. • Replace the charge unit of the PCU (CBG power pack for the K PCU, charge roller unit for YMC PCUs) |
| Remedy: | • Charge roller dirty • Charge roller defective • Bias terminal connection at the PCU receptacle is dirty or defective |
| Error code: | SC318 |
| Description: | AC bias charge adjustment error 3: C An average value of 8 ms/cycle could not be attained for Vpp (AC charge bias) within 15 attempts. -or- The output of the AC charge boosted Vpp over 2.8 kV. |
| Causes: | • Check the connections of the charge unit of the PCU where the problem occurred. • Replace the charge unit of the PCU (CBG power pack for the K PCU, charge roller unit for YMC PCUs) |
| Remedy: | • Charge roller dirty • Charge roller defective • Bias terminal connection at the PCU receptacle is dirty or defective |
| Error code: | SC319 |
| Description: | AC bias charge adjustment error 4: Y An average value of 8 ms/cycle could not be attained for Vpp (AC charge bias) within 15 attempts. -or- The output of the AC charge boosted Vpp over 2.8 kV. |
| Causes: | • Check the connections of the charge unit of the PCU where the problem occurred. • Replace the charge unit of the PCU (CBG power pack for the K PCU, charge roller unit for YMC PCUs) |
| Remedy: | • Charge roller dirty • Charge roller defective • Bias terminal connection at the PCU receptacle is dirty or defective |
| Error code: | SC320 |
| Description: | Development power pack error 1: K An interrupt checks the status of the each power pack every 2 ms. This SC is issued if the BICU detects a short in the development DC charge for black, magenta, cyan, or yellow (or V = 0) for 500 ms (250 times). |
| Causes: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective |
| Remedy: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective 1. Disconnect the high voltage cable from Terminal B of the high-voltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is "0" or nearly "0", check the high-voltage harness for defects and replace it if necessary. If replacing the harness does not solve the problem, 4. Test the resistance between the development unit terminal and the ground. If there is no resistance (0Ù) between the development unit and the ground, replace the development unit. 5. If there is no development PWM signal, replace the harness and/or IOB. |
| Error code: | SC321 |
| Description: | Development power pack error 2: M An interrupt checks the status of the each power pack every 2 ms. This SC is issued if the BICU detects a short in the development DC charge for black, magenta, cyan, or yellow (or V = 0) for 500 ms (250 times). |
| Causes: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective |
| Remedy: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective 1. Disconnect the high voltage cable from Terminal B of the high-voltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is "0" or nearly "0", check the high-voltage harness for defects and replace it if necessary. If replacing the harness does not solve the problem, 4. Test the resistance between the development unit terminal and the ground. If there is no resistance (0Ù) between the development unit and the ground, replace the development unit. 5. If there is no development PWM signal, replace the harness and/or IOB. |
| Error code: | SC322 |
| Description: | Development power pack error 3: C An interrupt checks the status of the each power pack every 2 ms. This SC is issued if the BICU detects a short in the development DC charge for black, magenta, cyan, or yellow (or V = 0) for 500 ms (250 times). |
| Causes: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective |
| Remedy: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective 1. Disconnect the high voltage cable from Terminal B of the high-voltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is "0" or nearly "0", check the high-voltage harness for defects and replace it if necessary. If replacing the harness does not solve the problem, 4. Test the resistance between the development unit terminal and the ground. If there is no resistance (0Ù) between the development unit and the ground, replace the development unit. 5. If there is no development PWM signal, replace the harness and/or IOB. |
| Error code: | SC323 |
| Description: | Development power pack error 4: Y An interrupt checks the status of the each power pack every 2 ms. This SC is issued if the BICU detects a short in the development DC charge for black, magenta, cyan, or yellow (or V = 0) for 500 ms (250 times). |
| Causes: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective |
| Remedy: | • Development power pack defective • High voltage power supply defective • High voltage power supply harness defective • Development unit defective • IOB harness disconnected or defective • IOB defective 1. Disconnect the high voltage cable from Terminal B of the high-voltage supply board. 2. Attach a voltmeter to the terminal. 3. If there is no output from the terminal, replace the high voltage power supply. -or- If there is output from the terminal, test the resistance between the high voltage cable and the ground. If resistance is "0" or nearly "0", check the high-voltage harness for defects and replace it if necessary. If replacing the harness does not solve the problem, 4. Test the resistance between the development unit terminal and the ground. If there is no resistance (0Ù) between the development unit and the ground, replace the development unit. 5. If there is no development PWM signal, replace the harness and/or IOB. |
| Error code: | SC324 |
| Description: | Development motor error 1: K The PLL lock signal remained HIGH or LOW for longer than the prescribed time for the development motor of the affected color. |
| Causes: | • Development motor shaft locked, blocked by obstruction • Development motor defective • DRB defective |
| Remedy: | • Development motor shaft locked, blocked by and obstruction • DRB (Drive Board) defective |
| Error code: | SC325 |
| Description: | Development motor error 2: M The PLL lock signal remained HIGH or LOW for longer than the prescribed time for the development motor of the affected color. |
| Causes: | • Development motor shaft locked, blocked by obstruction • Development motor defective • DRB defective |
| Remedy: | • Development motor shaft locked, blocked by and obstruction • DRB (Drive Board) defective |
| Error code: | SC326 |
| Description: | Development motor error 3: C The PLL lock signal remained HIGH or LOW for longer than the prescribed time for the development motor of the affected color. |
| Causes: | • Development motor shaft locked, blocked by obstruction • Development motor defective • DRB defective |
| Remedy: | • Development motor shaft locked, blocked by and obstruction • DRB (Drive Board) defective |
| Error code: | SC327 |
| Description: | Development motor error 4: Y The PLL lock signal remained HIGH or LOW for longer than the prescribed time for the development motor of the affected color. |
| Causes: | • Development motor shaft locked, blocked by obstruction • Development motor defective • DRB defective |
| Remedy: | • Development motor shaft locked, blocked by and obstruction • DRB (Drive Board) defective |
| Error code: | SC336 |
| Description: | Developer set error 1: K The value of Vcnt is set at the maximum or minimum setting when the TD sensor is initialized. |
| Causes: | 1. Open the front door. 2. Pull out the film seal from the black, magenta, cyan, or yellow developer bottle. 3. Do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for K. • SP3801 004 to initialize the TD sensor for M. • SP3801 005 to initialize the TD sensor for C. • SP3801 006 to initialize the TD sensor for Y |
| Remedy: | • Film seal not removed from the black, magenta, cyan, or yellow developer case Open the front door. Pull out the film seal from the black, magenta, cyan, or yellow developer case. Be sure to do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for black. • SP3801 004 to initialize the TD sensor for magenta. • SP3801 005 to initialize the TD sensor for cyan. • SP3801 006 to initialize the TD sensor for yellow. |
| Error code: | SC337 |
| Description: | Developer set error 2: M The value of Vcnt is set at the maximum or minimum setting when the TD sensor is initialized. |
| Causes: | 1. Open the front door. 2. Pull out the film seal from the black, magenta, cyan, or yellow developer bottle. 3. Do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for K. • SP3801 004 to initialize the TD sensor for M. • SP3801 005 to initialize the TD sensor for C. • SP3801 006 to initialize the TD sensor for Y |
| Remedy: | • Film seal not removed from the black, magenta, cyan, or yellow developer case Open the front door. Pull out the film seal from the black, magenta, cyan, or yellow developer case. Be sure to do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for black. • SP3801 004 to initialize the TD sensor for magenta. • SP3801 005 to initialize the TD sensor for cyan. • SP3801 006 to initialize the TD sensor for yellow. |
| Error code: | SC338 |
| Description: | Developer set error 3: C The value of Vcnt is set at the maximum or minimum setting when the TD sensor is initialized. |
| Causes: | 1. Open the front door. 2. Pull out the film seal from the black, magenta, cyan, or yellow developer bottle. 3. Do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for K. • SP3801 004 to initialize the TD sensor for M. • SP3801 005 to initialize the TD sensor for C. • SP3801 006 to initialize the TD sensor for Y |
| Remedy: | • Film seal not removed from the black, magenta, cyan, or yellow developer case Open the front door. Pull out the film seal from the black, magenta, cyan, or yellow developer case. Be sure to do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for black. • SP3801 004 to initialize the TD sensor for magenta. • SP3801 005 to initialize the TD sensor for cyan. • SP3801 006 to initialize the TD sensor for yellow. |
| Error code: | SC339 |
| Description: | Developer set error 4: Y The value of Vcnt is set at the maximum or minimum setting when the TD sensor is initialized. |
| Causes: | 1. Open the front door. 2. Pull out the film seal from the black, magenta, cyan, or yellow developer bottle. 3. Do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for K. • SP3801 004 to initialize the TD sensor for M. • SP3801 005 to initialize the TD sensor for C. • SP3801 006 to initialize the TD sensor for Y |
| Remedy: | • Film seal not removed from the black, magenta, cyan, or yellow developer case Open the front door. Pull out the film seal from the black, magenta, cyan, or yellow developer case. Be sure to do the correct SP for the affected color: • SP3801 003 to initialize the TD sensor for black. • SP3801 004 to initialize the TD sensor for magenta. • SP3801 005 to initialize the TD sensor for cyan. • SP3801 006 to initialize the TD sensor for yellow. |
| Error code: | SC340 |
| Description: | Toner cartridge set error 1: K The machine cannot read the ID chip of the black, magenta, cyan, or yellow toner cartridge. |
| Causes: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly |
| Remedy: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly 1. Open the front door. 2. Press down the release lever on the top edge of the toner bin to of the affect toner cartridge to release it, then pull the bin out to open it. 3. Remove the toner cartridge and set it again. |
| Error code: | SC341 |
| Description: | Toner cartridge set error 2: M The machine cannot read the ID chip of the black, magenta, cyan, or yellow toner cartridge. |
| Causes: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly |
| Remedy: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly 1. Open the front door. 2. Press down the release lever on the top edge of the toner bin to of the affect toner cartridge to release it, then pull the bin out to open it. 3. Remove the toner cartridge and set it again. |
| Error code: | SC342 |
| Description: | Toner cartridge set error 3: C The machine cannot read the ID chip of the black, magenta, cyan, or yellow toner cartridge. |
| Causes: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly |
| Remedy: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly 1. Open the front door. 2. Press down the release lever on the top edge of the toner bin to of the affect toner cartridge to release it, then pull the bin out to open it. 3. Remove the toner cartridge and set it again. |
| Error code: | SC343 |
| Description: | Toner cartridge set error 4: Y The machine cannot read the ID chip of the black, magenta, cyan, or yellow toner cartridge. |
| Causes: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly |
| Remedy: | • Black, magenta, cyan, or yellow toner cartridge set incorrectly 1. Open the front door. 2. Press down the release lever on the top edge of the toner bin to of the affect toner cartridge to release it, then pull the bin out to open it. 3. Remove the toner cartridge and set it again. |
| Error code: | SC348 |
| Description: | Toner hopper motor error. 2 sec. after the motor START signal is output, a LOCK signal cannot be detected. |
| Causes: | • Motor harness disconnected, loose, or defective • Toner pump overload • Sub hopper overload • Toner hopper motor defective |
| Remedy: | • Motor harness disconnected, loose, or defective • Powder pump overload • Sub hopper overload • Toner hopper motor defective |
| Error code: | SC360 |
| Description: | TD sensor (Vt high) error 1: K The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds 4.5V for two counts. |
| Causes: | These SC codes are issued if the TD sensor output is greater than 4.7V after 20 consecutive readings. |
| Remedy: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor. 1. Turn the machine OFF and ON. 2. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the black TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC361 |
| Description: | TD sensor (Vt high) error 2: M The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds 4.5V for two counts. |
| Causes: | These SC codes are issued if the TD sensor output is greater than 4.7V after 20 consecutive readings. |
| Remedy: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor. 1. Turn the machine OFF and ON. 2. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the black TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC362 |
| Description: | TD sensor (Vt high) error 3: C The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds 4.5V for two counts. |
| Causes: | These SC codes are issued if the TD sensor output is greater than 4.7V after 20 consecutive readings. |
| Remedy: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor. 1. Turn the machine OFF and ON. 2. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the black TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC363 |
| Description: | TD sensor (Vt high) error 4: Y The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds 4.5V for two counts. |
| Causes: | These SC codes are issued if the TD sensor output is greater than 4.7V after 20 consecutive readings. |
| Remedy: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor. 1. Turn the machine OFF and ON. 2. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the black TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC364 |
| Description: | TD sensor (Vt low) error 1: K The Vt value of the black, magenta, cyan, or yellow TD sensor is below 0.5V for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective, replace the PCU Note: The TD sensor cannot be replaced independently. The PCU must be replaced if the TD sensor is defective. |
| Remedy: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective 1. Turn the machine OFF and ON. 2. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC365 |
| Description: | TD sensor (Vt low) error 2: M The Vt value of the black, magenta, cyan, or yellow TD sensor is below 0.5V for 10 counts. |
| Causes: | These SC codes are issued if the TD sensor output is less than 0.5V after 10 consecutive readings. |
| Remedy: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective 1. Turn the machine OFF and ON. 2. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC366 |
| Description: | TD sensor (Vt low) error 3: C The Vt value of the black, magenta, cyan, or yellow TD sensor is below 0.5V for 10 counts. |
| Causes: | These SC codes are issued if the TD sensor output is less than 0.5V after 10 consecutive readings. |
| Remedy: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective 1. Turn the machine OFF and ON. 2. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC367 |
| Description: | TD sensor (Vt low) error 4: Y The Vt value of the black, magenta, cyan, or yellow TD sensor is below 0.5V for 10 counts. |
| Causes: | These SC codes are issued if the TD sensor output is less than 0.5V after 10 consecutive readings. |
| Remedy: | • TD sensor harness disconnected, loose, defective • A drawer connector (located on the rear of a development unit) disconnected, loose, defective • TD sensor defective 1. Turn the machine OFF and ON. 2. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 3. Check the drawer connector. 4. Replace the TD sensor. 5. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC372 |
| Description: | TD sensor adjustment error 1: K During TD sensor initialization with SP3801, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of 3.2±0.2V |
| Causes: | The TD sensor of the affected development unit could not be initialized within 2.9±0.2V. |
| Remedy: | • Film seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective 1. Turn the machine OFF and ON. 2. Pull ouut the film seal from the black, magenta, cyan, or yellow PCU. 3. Do SP3812 001 to confirm that the developer was initialized correctly. The display should show "1111" if developer initialized correctly. 4. Check the TD sensor connector. 5. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 6. Check the drawer PCU connector. 7. Replace the TD sensor. 8. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC373 |
| Description: | TD sensor adjustment error 2: M During TD sensor initialization with SP3801, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of 3.2±0.2V |
| Causes: | The TD sensor of the affected development unit could not be initialized within 2.9±0.2V. |
| Remedy: | • Film seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective 1. Turn the machine OFF and ON. 2. Pull ouut the film seal from the black, magenta, cyan, or yellow PCU. 3. Do SP3812 001 to confirm that the developer was initialized correctly. The display should show "1111" if developer initialized correctly. 4. Check the TD sensor connector. 5. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 6. Check the drawer PCU connector. 7. Replace the TD sensor. 8. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC374 |
| Description: | TD sensor adjustment error 3: C During TD sensor initialization with SP3801, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of 3.2±0.2V |
| Causes: | TD harness sensor disconnected, loose or defective Harness between TD sensor and drawer disconnected, defective • TD sensor defective, replace the PCU Note: The TD sensor cannot be replaced independently. The PCU must be replaced if the TD sensor is defective. |
| Remedy: | • Film seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective 1. Turn the machine OFF and ON. 2. Pull ouut the film seal from the black, magenta, cyan, or yellow PCU. 3. Do SP3812 001 to confirm that the developer was initialized correctly. The display should show "1111" if developer initialized correctly. 4. Check the TD sensor connector. 5. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 6. Check the drawer PCU connector. 7. Replace the TD sensor. 8. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC375 |
| Description: | TD sensor adjustment error 4: Y During TD sensor initialization with SP3801, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of 3.2±0.2V |
| Causes: | The voltage reading during process control for Vsg_reg was not within the correct range (4.0±0.5V). Vsg_reg is the voltage reading of the light reflected directly from the bare surface of the ITB. |
| Remedy: | • Film seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective 1. Turn the machine OFF and ON. 2. Pull ouut the film seal from the black, magenta, cyan, or yellow PCU. 3. Do SP3812 001 to confirm that the developer was initialized correctly. The display should show "1111" if developer initialized correctly. 4. Check the TD sensor connector. 5. Check the TD sensor connector and harness between the TD sensor and PCU for damage. Replace it if necessary. 6. Check the drawer PCU connector. 7. Replace the TD sensor. 8. After replacing the TD sensor: • Do SP3801 003-006 to initialize the new black, magenta, cyan, or yellow TD sensor. • Execute SP3820 001 to do auto process control manually. |
| Error code: | SC396 |
| Description: | Drum motor error 1: K When the drum motor of the black, magenta, cyan, or yellow PCU starts, the machine cannot detect a LOCK signal within 2 sec. The motor is trying to rotate but there is an excessive load on the drum shaft. The motor has no traction (due to a bent cleaning blade, for example). |
| Causes: | • Disconnected or defective motor harness. • Motor slips due to excessive load |
| Remedy: | • PCU drum dirty • PCU defective • Motor harness defective • DRB (Drive board) defective • Drum motor defective • Insufficient lubrication on a drum. Open PCU and apply toner to the drum surface |
| Error code: | SC397 |
| Description: | Drum motor error 2: M When the drum motor of the black, magenta, cyan, or yellow PCU starts, the machine cannot detect a LOCK signal within 2 sec. The motor is trying to rotate but there is an excessive load on the drum shaft. The motor has no traction (due to a bent cleaning blade, for example). |
| Causes: | • Disconnected or defective motor harness. • Motor slips due to excessive load |
| Remedy: | • PCU drum dirty • PCU defective • Motor harness defective • DRB (Drive board) defective • Drum motor defective • Insufficient lubrication on a drum. Open PCU and apply toner to the drum surface |
| Error code: | SC398 |
| Description: | Drum motor error 3: C When the drum motor of the black, magenta, cyan, or yellow PCU starts, the machine cannot detect a LOCK signal within 2 sec. The motor is trying to rotate but there is an excessive load on the drum shaft. The motor has no traction (due to a bent cleaning blade, for example). |
| Causes: | • Drum motor harness loose, broken, defective • Drum motor defective • DTMB defective |
| Remedy: | • PCU drum dirty • PCU defective • Motor harness defective • DRB (Drive board) defective • Drum motor defective • Insufficient lubrication on a drum. Open PCU and apply toner to the drum surface |
| Error code: | SC399 |
| Description: | Drum motor error 4: Y When the drum motor of the black, magenta, cyan, or yellow PCU starts, the machine cannot detect a LOCK signal within 2 sec. The motor is trying to rotate but there is an excessive load on the drum shaft. The motor has no traction (due to a bent cleaning blade, for example). |
| Causes: | • Drum motor harness loose, broken, defective • Drum motor defective • DTMB defective |
| Remedy: | • PCU drum dirty • PCU defective • Motor harness defective • DRB (Drive board) defective • Drum motor defective • Insufficient lubrication on a drum. Open PCU and apply toner to the drum surface |
| Error code: | SC400 |
| Description: | ID sensor error 1: Calibration Before adjustment Vsg_reg<0.5 but Vsg_reg could not be adjusted to the target Vsg_reg = 4.0±0.2V during process control. |
| Causes: | • TM sensors are dirty. • A solid print out due to an electrostatic charging error • The TM sensor is defective. |
| Remedy: | • ID sensor harness disconnected, loose, defective • ID sensor dirty • ID sensor defective • ITB unit drawer connector dirty |
| Error code: | SC410 |
| Description: | ID sensor error 2: Development γ K Development gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • LD sensor harness loose, broken, defective • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective) |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59 to 59, and 61 (section 4.2.4) • Potential sensor defective • Laser diode not firing • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC411 |
| Description: | ID sensor error 3: Development γ M Development gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • LD sensor harness loose, broken, defective • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective) |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59 to 59, and 61 (section 4.2.4) • Potential sensor defective • Laser diode not firing • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC412 |
| Description: | ID sensor error 4: Development γ C Development gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • LD sensor harness loose, broken, defective • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective) |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59 to 59, and 61 (section 4.2.4) • Potential sensor defective • Laser diode not firing • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC413 |
| Description: | ID sensor error 5: Development γ Y Development gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • LD sensor harness loose, broken, defective • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective) |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59 to 59, and 61 (section 4.2.4) • Potential sensor defective • Laser diode not firing • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC414 |
| Description: | ID sensor error 6: Development start voltage K The development start voltage in the development of the black, magenta, cyan, or yellow PCU is not within the correct range (±150V) |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59, and 61 (section 4.2.4) • Potential sensor defective • LD not firing correctly • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC415 |
| Description: | ID sensor error 7: Development start voltage M The development start voltage in the development of the black, magenta, cyan, or yellow PCU is not within the correct range (±150V) |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59, and 61 (section 4.2.4) • Potential sensor defective • LD not firing correctly • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC416 |
| Description: | ID sensor error 8: Development start voltage C The development start voltage in the development of the black, magenta, cyan, or yellow PCU is not within the correct range (±150V) |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59, and 61 (section 4.2.4) • Potential sensor defective • LD not firing correctly • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC417 |
| Description: | ID sensor error 9: Development start voltage Y The development start voltage in the development of the black, magenta, cyan, or yellow PCU is not within the correct range (±150V) |
| Causes: | • Toner density abnormal. Refer to the image troubleshooting section in Section 4 of the Venus-C1 B132 Service Manual (Self-Check Error Codes 55 to 59, 61). • Potential sensor defective • LD unit not firing • ITB separation for CMY abnormal • Transfer power pack defective |
| Remedy: | • Toner density not normal: Refer to the procedure for process control self-check error codes 55 to 59, and 61 (section 4.2.4) • Potential sensor defective • LD not firing correctly • ITB separation for CMY abnormal • Transfer power pack defective • ID sensor defective |
| Error code: | SC418 |
| Description: | LED error during Vsg adjustment. PWM value: Ifsg>2000 This means the current to the LED of the ID sensor is abnormal. |
| Causes: | • ID sensor dirty • ID sensor defective |
| Remedy: | • ID sensor dirty • ID sensor defective |
| Error code: | SC420 |
| Description: | Potential sensor error 1: Vd Adjustment K The development potential of the drum before exposure (Vd) cannot be adjusted to within ±10 V of the target voltage (- 900V). |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Development power pack defective • VBCU defective |
| Remedy: | • Toner density low |
| Error code: | SC421 |
| Description: | Potential sensor error 2: Vd Adjustment M The development potential of the drum before exposure (Vd) cannot be adjusted to within ±10 V of the target voltage (- 900V). |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Development power pack defective • VBCU defective |
| Remedy: | • Toner density low |
| Error code: | SC422 |
| Description: | Potential sensor error 3: Vd Adjustment C The development potential of the drum before exposure (Vd) cannot be adjusted to within ±10 V of the target voltage (- 900V). |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Development power pack defective • VBCU defective |
| Remedy: | • Toner density low |
| Error code: | SC423 |
| Description: | Potential sensor error 4: Vd Adjustment Y The development potential of the drum before exposure (Vd) cannot be adjusted to within ±10 V of the target voltage (- 900V). |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Development power pack defective • VBCU defective |
| Remedy: | • Toner density low |
| Error code: | SC424 |
| Description: | Potential sensor error 5: Vl adjustment K Vpl could not be adjusted to within ±10V of the target Vpl after exposure of the ID sensor patterns. |
| Causes: | • Drum worn • LD unit dirty • Poor drum ground connection |
| Remedy: | • Toner density low |
| Error code: | SC425 |
| Description: | Potential sensor error 6: Vl adjustment M Vpl could not be adjusted to within ±10V of the target Vpl after exposure of the ID sensor patterns. |
| Causes: | • Drum worn • LD unit dirty • Poor drum ground connection |
| Remedy: | • Toner density low |
| Error code: | SC426 |
| Description: | Potential sensor error 7: Vl adjustment C Vpl could not be adjusted to within ±10V of the target Vpl after exposure of the ID sensor patterns. |
| Causes: | • Drum worn • LD unit dirty • Poor drum ground connection |
| Remedy: | • Toner density low |
| Error code: | SC427 |
| Description: | Potential sensor error 8: Vl adjustment Y Vpl could not be adjusted to within ±10V of the target Vpl after exposure of the ID sensor patterns. |
| Causes: | • Drum worn • LD unit dirty • Poor drum ground connection |
| Remedy: | • Toner density low |
| Error code: | SC432 |
| Description: | Potential sensor error 1: Vr K Vr > 200V The residual voltage (Vr), the amount of voltage that remains on the surface of the drum after the Quenching Lamp fires is greater than 200V. |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Toner density low |
| Error code: | SC433 |
| Description: | Potential sensor error 2: Vr M Vr > 200V The residual voltage (Vr), the amount of voltage that remains on the surface of the drum after the Quenching Lamp fires is greater than 200V. |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Toner density low |
| Error code: | SC434 |
| Description: | Potential sensor error 3: Vr C Vr > 200V The residual voltage (Vr), the amount of voltage that remains on the surface of the drum after the Quenching Lamp fires is greater than 200V. |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Toner density low |
| Error code: | SC435 |
| Description: | Potential sensor error 4: Vr Y Vr > 200V The residual voltage (Vr), the amount of voltage that remains on the surface of the drum after the Quenching Lamp fires is greater than 200V. |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Toner density low |
| Error code: | SC436 |
| Description: | Potential sensor error 5: Vd K The VdHome reading, the first step of the process control self-check, detected that the development potential of the unexposed areas of the drum are not within the prescribed range (-500 to -700) |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Error code: | SC437 |
| Description: | Potential sensor error 6: Vd M The VdHome reading, the first step of the process control self-check, detected that the development potential of the unexposed areas of the drum are not within the prescribed range (-500 to -700) |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Error code: | SC438 |
| Description: | Potential sensor error 7: Vd C The VdHome reading, the first step of the process control self-check, detected that the development potential of the unexposed areas of the drum are not within the prescribed range (-500 to -700) |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Error code: | SC439 |
| Description: | Potential sensor error 8: Vd Y The VdHome reading, the first step of the process control self-check, detected that the development potential of the unexposed areas of the drum are not within the prescribed range (-500 to -700) |
| Causes: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Remedy: | • Potential sensor dirty • Potential sensor defective • Charge roller defective • Charge power pack defective • OPC defective |
| Error code: | SC440 |
| Description: | Image transfer power pack error 1: K An interrupt checks the status of the power pack every 2 ms. This SCis issued if the BICU detects a short in the power pack for K, M, C, or Y 250 times within 500 ms. |
| Causes: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged |
| Remedy: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged • IOB damaged |
| Error code: | SC441 |
| Description: | Image transfer power pack error 2: M An interrupt checks the status of the power pack every 2 ms. This SCis issued if the BICU detects a short in the power pack for K, M, C, or Y 250 times within 500 ms. |
| Causes: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged |
| Remedy: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged • IOB damaged |
| Error code: | SC442 |
| Description: | Image transfer power pack error 3: C An interrupt checks the status of the power pack every 2 ms. This SCis issued if the BICU detects a short in the power pack for K, M, C, or Y 250 times within 500 ms. |
| Causes: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged |
| Remedy: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged • IOB damaged |
| Error code: | SC443 |
| Description: | Image transfer power pack error 4: Y An interrupt checks the status of the power pack every 2 ms. This SCis issued if the BICU detects a short in the power pack for K, M, C, or Y 250 times within 500 ms. |
| Causes: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged |
| Remedy: | • Transfer belt damaged, insulation damaged • Insulation on high voltage cable damaged • Another hot point inside the machine has damaged insulation • Insulation around high-voltage power supply damaged • IOB damaged |
| Error code: | SC445 |
| Description: | Image transfer motor error The control board of the image transfer motor generated signals that indicate there is problem with the image transfer motor. |
| Causes: | • Defective ITB contact motor • Defective ITB contact sensor • Defective ITB unit |
| Remedy: | • Image transfer motor defective • ITB control board defective • ITB overloaded • Encoder strip on the front edge of the belt damaged. |
| Error code: | SC446 |
| Description: | ITB lift motor error The state of the ITB lift sensor does not change its state (switching from OFF to ON or vice versa), even after the ITB lift motor starts rotating. |
| Causes: | The transfer belt drive motor failed to start within the prescribed time or failed during normal operation. |
| Remedy: | • ITB lift sensor dirty, disconnected, defective • ITB lift motor disconnected, defective |
| Error code: | SC450 |
| Description: | Transfer power pack output error An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the power pack 250 times at 2nd transfer output within 500 ms. |
| Causes: | • Damaged insulation on the high-voltage supply cable • Damaged insulation around the highvoltage power supply. • Check SIOB harness connections • SIOB defective |
| Remedy: | • Damaged insulation on the high-voltage supply cable • Damaged insulation around the highvoltage power supply. |
| Error code: | SC455 |
| Description: | PTR motor error The lock signal from the paper transfer motor is not detected within 1 sec. after the motor switched ON. |
| Causes: | • Motor disconnected • PTR shaft locked, needs cleaning, blocked by obstruction • Drive shaft of the ITB locked and overloaded, needs cleaning, or blocked by obstruction • DRB disconnected, defective |
| Remedy: | • Motor disconnected • PTR shaft locked, needs cleaning, blocked by obstruction • Drive shaft of the ITB locked and overloaded, needs cleaning, or blocked by obstruction • DRB (motor drive board) disconnected, defective |
| Error code: | SC460 |
| Description: | Separation power pack output error An interrupt checks the status of the power pack every 2 ms. This SC is issued if the BICU detects a short in the power pack 250 times at D(AC) within 500 ms. |
| Causes: | • Damaged insulation on the high-voltage supply cable (replace cable) • Damaged insulation around the transfer power pack |
| Remedy: | • Damaged insulation on the high-voltage supply cable • Damaged insulation around the highvoltage power supply. 1. Replace the high-voltage supply cable. 2. Replace the high-voltage power supply unit. 3. Replace the IOB. |
| Error code: | SC484 |
| Description: | Waste toner bottle full The toner full sensor goes HIGH for more than 500 ms, indicating that the waste toner bottle is full. |
| Causes: | • Remove the used toner bottle • Empty the used toner bottle and reinstall it |
| Remedy: | • Remove waste toner bottle, empty it |
| Error code: | SC485 |
| Description: | Waste toner transport motor error The lock signal of the waste toner transport motor remains HIGH for more than 600 ms. |
| Causes: | The used toner transport motor failed to start within the prescribed time or failed during normal operation. |
| Remedy: | • Waste toner transport motor defective |
| Error code: | SC487 |
| Description: | Waste toner bottle set error The set sensor of the waste toner bottle remains LOW for more than 500 ms. (The sensor goes HIGH when the bottle is installed correctly.) |
| Causes: | • Used toner bottle not installed • Remove used toner bottle and reinstall correctly |
| Remedy: | • Install the waste toner bottle • Remove waste toner bottle and reinstall correctly |
| Error code: | SC488 |
| Description: | Waste toner transport lock Waste toner cannot be transported to the waste toner bottle. |
| Causes: | Used toner is not being moved to the used toner bottle. |
| Remedy: | • Blockage in the line to the waste toner bottle |
| Error code: | SC490 |
| Description: | Peltier Unit error The Abnormal Condition signal or the Peltier Unit is received 10 times. |
| Causes: | • No ITB unit in the machine • Dirty TM sensor |
| Remedy: | • Peltier Unit is defective |
| Error code: | SC496 |
| Description: | MUSIC sensor error The MUSIC sensor detected an abnormal pattern on the ITB because: • A/D converter exceeded upper or lower limit. • The pattern used to calculate the amount of skew is abnormal. • The reading of the pattern exceeded the length of time the LED projected light. • LED light could not be adjusted correctly. |
| Causes: | This SC is issued if one or more of the following occurred: • MUSIC sensor sampling abnormal • Sensor LED adjustment abnormal • Number of patches abnormal • ITB scratched • Main scan registration abnormal • Sub scan registration abnormal • Main scan magnification abnormal • Main scan magnification error diffusion abnormal • Lens refraction abnormal |
| Remedy: | • MUSIC sensor defective or disconnected • MUSIC pattern abnormal; do a forced process control (SP3821) and check the result (section 4.2.4). |
| Error code: | SC497 |
| Description: | Temperature and humidity sensor error 1: PCU The thermistor output of the temperature and humidity sensor above the black PCU was not within the prescribed range (0.5V to 4.2V) |
| Causes: | The machine detected one of these problems with the temperature/humidity sensor located under the rear end of the K PCDU: • The temperature sensor output was less than 0.5V or more than 2.8V three times in one minute, indicating a problem with the temperature detection. • The humidity sensor output was more than 2.4V for three times in one minute, indicating a problem with humidity detection. |
| Remedy: | • Temperature and humidity sensor harness disconnected, loose, defective • Temperature and humidity sensor defective |
| Error code: | SC498 |
| Description: | Temperature and humidity sensor error 2 The thermistor output of the temperature and humidity sensor at below the waste toner bottle was not within the prescribed range (0.5V to 4.2V) |
| Causes: | The machine detected one of these problems with the temperature/humidity sensor located under the rear end of the K PCDU: • The temperature sensor output was less than 0.5V or more than 2.8V three times in one minute, indicating a problem with the temperature detection. • The humidity sensor output was more than 2.4V for three times in one minute, indicating a problem with humidity detection. |
| Remedy: | • Temperature and humidity sensor harness disconnected, loose, defective • Temperature and humidity sensor defective |
| Error code: | SC499 |
| Description: | ITB Position Sensor error Abnormal ITB Position Sensor output. |
| Causes: | The ITB sensor that reads the encoded film strip on the edge of the image transfer belt was not operating correctly. (The TDCU constantly monitors operation of the ITB with transfer feed-back control.) |
| Remedy: | • ITB Position Sensor 1 or 2 is dirty. • ITB Position Sensor 1 or 2 is defective. • ITB encoder strip is dirty, • ITB encoder strip is damaged. • ITB movement error (e.g. the belt cannot rotate correctly due to friction). 1. Connectors for ITB Position Sensor 1 or 2 are not connected correctly. |
| Error code: | SC501 |
| Description: | Tray 1 (tandem tray) feed error (Japan Only) • The tray 1 lift sensor does not switch ON 10 s after the tray lift motor switches ON and starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. • The lower limit sensor of the tandem tray does not detect the lower limit within 10 sec. |
| Causes: | • Tray lift motor harness disconnected, loose, defective • Paper or other obstacle trapped between tray and motor • Tray lift sensor disconnected, damaged • Lower limit sensor disconnected, damaged • Pick-up solenoid disconnected, blocked by an obstacle |
| Remedy: | • Tray lift motor harness disconnected, loose, defective • Paper or other obstacle trapped between tray and motor • Tray lift sensor disconnected, damaged • Lower limit sensor disconnected, damaged • Pick-up solenoid disconnected, blocked by an obstacle |
| Error code: | SC502 |
| Description: | Tray 2 (paper cassette) feed error (Japan Only) • The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. • The lower limit sensor of the tandem tray does not detect the lower limit within 10 sec. |
| Causes: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Remedy: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Error code: | SC503 |
| Description: | Tray 1 feed error • The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. |
| Causes: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Remedy: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Error code: | SC504 |
| Description: | Tray 2 feed error • The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 sec. |
| Causes: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Remedy: | • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle |
| Error code: | SC505 |
| Description: | Tandem tray rear fence motor error • The return sensor does not switch ON within 10 sec. after the rear fence motor switches ON. • The HP sensor does not switch ON 10 sec. after the rear fence motor switches ON. • The HP sensor and return sensor switch ON at the same time. |
| Causes: | • Rear fence motor defective or poor connection • Paper or other obstacle interfering with operation of the sensors • Paper or other obstacle trapped between tray and motor • Motor mechanical overload due to obstruction • Return sensor or HP sensor defective or dirty |
| Remedy: | • Rear fence motor defective or poor connection • Paper or other obstacle interfering with operation of the sensors • Paper or other obstacle trapped between tray and motor • Motor mechanical overload due to obstruction • Return sensor or HP sensor defective or dirty |
| Error code: | SC506 |
| Description: | Tandem tray back fence motor error. The back fence should be closed but the fence was not detected in the closed position within 500 ms. -or- The back fence should be open but the fence was not detected in the open within 500 ms. |
| Causes: | The tray lift motor, pick-up solenoid, lift sensor, or lower limit sensor did not operate correctly. |
| Remedy: | • Paper loaded incorrectly • Back fence motor harness disconnected, loose, defective • Back fence motor defective • Paper blocking sensors • Paper stuck between tray and motor • Back fence close, back fence open sensor harnesses disconnected, loose, or defective. • Back fence close, back fence open sensor defective • Paper or other obstacle is interfering with movement of the fence |
| Error code: | SC510 |
| Description: | LCT tray error. • When the bottom plate is lifted, the upper limit sensor does not come on for 30 sec. • When the bottom plate is lowered, the lower limit sensor does not come on for 30 sec. • After lift begins, the upper limit sensor does not switch ON before the pick-up solenoid switches ON. • The paper end sensor switches ON during lift and the upper limit sensor does not switch ON for 2.5 s, and a message prompts user to reset paper. |
| Causes: | • Tray lift motor harness, disconnected, loose, or defective • Tray lift motor defective • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective |
| Remedy: | • Tray lift motor harness, disconnected, loose, or defective • Tray lift motor defective • Lift sensor defective or disconnected • Pick-up solenoid defective or disconnected • Paper end sensor defective |
| Error code: | SC515 |
| Description: | Duplex jogger motor error 1. When the jogger fence moves to the home position, the jogger fence HP sensor does not switch on even after the duplex jogger motor has moved the jogger fence 153.5 mm. |
| Causes: | The CIS cleaning fan motor in the right drawer failed to start within the prescribed time or failed during normal operation. |
| Remedy: | • Rear fence motor defective or poor connection • Paper or other obstacle interfering with operation of the sensors or motor • Return sensor or HP sensor defective or dirty |
| Error code: | SC516 |
| Description: | Duplex jogger motor error 2. When the jogger fence moves from the home position, the jogger fence HP sensor does not turn off even if the duplex jogger motor has moved the jogger fence 153.5 mm. |
| Causes: | A LOW motor LOCK signal was not detected after the motor switched off after 10 consecutive attempts. |
| Remedy: | • Paper or other obstacle has jammed mechanism • HP sensor connector disconnected or defective • HP sensor defective |
| Error code: | SC520 |
| Description: | Fusing/Exit Motor error. The Fusing/Exit Motor LOCK signal is not detected for a duration of one second after the motor START signal is sent. |
| Causes: | • Torque overload • Defective main motor • Disconnected or defective motor harness |
| Remedy: | • Fusing/Exit Motor connecter is not connected correctly. • Fusing/Exit Motor torque is too high or too low. • Fusing/Exit Motor is defective. |
| Error code: | SC530 |
| Description: | Fan error 1: fusing cooling fan motor. The BICU does not receive the lock signal 5 seconds after the fusing unit fan switches ON. |
| Causes: | • Disconnected or defective motor harness. • Defective LSU fan motor |
| Remedy: | • Fusing cooling fan disconnected, defective • BICU defective |
| Error code: | SC531 |
| Description: | Fan error 2: fusing cooling fan motor. The lock signal remained HIGH for 5 sec. while the fan at the front of the fusing unit near the heat dissipation fins was operating. |
| Causes: | • Disconnected or defective motor harness. • Defective LSU fan motor |
| Remedy: | • Motor overload due to obstacle interfering with operation of the fan • Fan harness loose, disconnected, defective • Fan defective |
| Error code: | SC532 |
| Description: | Fan error 3: PCB box fan. The lock signal remained HIGH for 5 sec. while the fan that cools the printed circuit boards was operating. |
| Causes: | • Disconnected or defective motor harness. • Defective air intake fan motor |
| Remedy: | • Motor overload due to obstacle interfering with operation of the fan • Fan harness loose, disconnected, defective • Fan defective |
| Error code: | SC533 |
| Description: | Fan error 4: fusing exhaust fan. The lock signal remained HIGH for 5 sec. while the fan that draws air out of the fusing unit was operating. |
| Causes: | • Disconnected or defective motor harness. • Defective PSU fan motor |
| Remedy: | • Motor overload due to obstacle interfering with operation of the fan • Fan harness loose, disconnected, defective • Fan defective |
| Error code: | SC534 |
| Description: | Fan error 5: duplex exhaust fan. The lock signal remained HIGH for 5 sec. while the fan that draws air out of the duplex unit was operating. |
| Causes: | • Fan harness disconnected or damaged • Fan blocked by an obstruction • Fan damaged |
| Remedy: | • Motor overload due to obstacle interfering with operation of the fan • Fan harness loose, disconnected, defective • Fan defective |
| Error code: | SC535 |
| Description: | Temperature/Humidity control abnormal. The output of the temperature/humidity sensor reaches the upper or lower limit, even after the Peltier unit has been ON for 3 hours. |
| Causes: | This is the small fan to the left or the large pressure roller fan on the front of the left drawer. |
| Remedy: | • Peltier Cooling Fan Motor is defective. |
| Error code: | SC541 |
| Description: | Heating roller thermistor 1 error 1: Poor connection. The temperature measured by the heating roller thermistor does not reach 130°C after 10 tries and 65 sec. have elapsed. |
| Causes: | • Disconnected thermistor • Defective harness connection |
| Remedy: | • Heating roller thermistor harness connection loose, disconnected, defective • Defective heating roller thermistor |
| Error code: | SC542 |
| Description: | Heating roller thermistor 1 error 2: No warmup. After the main switch is turned ON or the cover is closed, the heating roller temperature does not reach the ready temperature within 2 sec. after the heater switches ON. -or- If the roller was below 45°C, the heating roller did not reach the ready temperature 2 sec. after reaching 45°C. Note: Thermistor 2 stops monitoring the temperature once Thermistor 1 detects ready temperature. |
| Causes: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp |
| Remedy: | • Thermistor is bent, installed incorrectly • Defective heating roller thermistor • Heating roller fusing lamp broken Do SP5810 to cancel the SC fusing code. |
| Error code: | SC543 |
| Description: | Heating roller thermistor 1 error 3: Software - High temperature. The thermistor detected a temperature over 230°C. |
| Causes: | • Defective I/O control (EGB) • Defective EGB |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature out of control Do SP5810 to cancel the SC fusing code. |
| Error code: | SC544 |
| Description: | Heating roller thermistor 1 error 4: Hardware - High temperature. The thermistor detected a temperature over 260°C. |
| Causes: | The machine detected the CPU port LOW twice at 100 ms intervals and issued this SC. This check is always done to check for overheating, even if SC543 does not detect the problem. |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC545 |
| Description: | Heating roller thermistor 1 error 5: Lamp remains ON. After hot roller reaches warmup temperature, the fusing lamps remained ON at full capacity for 25 sec. after reaching the warmup temperature while the hot roller was not rotating. |
| Causes: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp |
| Remedy: | • Thermistor damaged, or out of position • Fusing lamp disconnected, broken |
| Error code: | SC546 |
| Description: | Heating roller thermistor 2 error 1: Thermistor disconnected. The temperature measured by the heating roller thermistor does not reach 0°C after 45 sec. and remains over this temperature for 10 readings. |
| Causes: | Unstable connector contact of fusing thermistor |
| Remedy: | • Loose connection of the heating roller thermistor • Defective heating roller thermistor |
| Error code: | SC547 |
| Description: | Zero cross error. When the main switch is turned ON, the machine checks how many zero-cross signals are generated within 500 ms. This SC code is issued if the number of zerocross signals detected is either more than 66 or less than 45 for 10 readings. Note: Zero cross signals, generated from an ac power supply, are used to generate a trigger pulses to control the applied power accurately. |
| Causes: | Defective fusing lamp relay |
| Remedy: | • Electrical noise on the power supply line • Fusing relay damaged: replace the PSU. Normally, this SC is cancelled if you do SP5810 to cancel the SC fusing code. |
| Error code: | SC548 |
| Description: | Heating roller thermistor 2 error 2: Failed to reach warmup temperature. After the main switch is turned ON or the cover is closed, the heating roller temperature does not reach the ready temperature within 2 sec. after the heater switches ON. -or- If the roller was below 45°C, the heating roller did not reach the ready temperature 2 sec. after reaching 45°C. Note: Thermistor 2 stops monitoring the temperature once Thermistor 1 detects warmup temperature. |
| Causes: | • Defective fusing lamp • Defective thermistor |
| Remedy: | • Thermistor is bent, installed incorrectly • Defective heating roller thermistor • Heating roller fusing lamp broken • Defective BICU |
| Error code: | SC549 |
| Description: | Heating roller thermistor 2 error 3: Software - High Temperature. The thermistor detected a temperature over 250°C. |
| Causes: | • Do SP5810 to cancel the SC fusing code. • TRIAC short, AC drive board defective • VBCU defective |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic. Do SP5810 to cancel the SC fusing code. |
| Error code: | SC550 |
| Description: | Heating roller thermistor 2 error 4: Hardware - High Temperature. The thermistor detected a temperature over 260°C. |
| Causes: | • Do SP5810 to cancel the SC fusing code. • TRIAC short, AC drive board defective • VBCU defective |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC551 |
| Description: | Pressure roller thermistor error 1. The temperature measured by the pressure roller thermistor does not reach 0°C for 200 sec. |
| Causes: | In the condition of relay ON, the end thermistor on the fusing detects less than 0 degrees Celsius for more than 5 seconds. |
| Remedy: | • Loose connection of the pressure roller thermistor • Defective pressure roller thermistor • Defective BICU Do SP5810 to cancel the SC fusing code. |
| Error code: | SC552 |
| Description: | Pressure roller thermistor error 2. After the main switch is turned ON or the cover is closed, the heating roller temperature does not reach the ready temperature within 2 sec. after the heater switches ON. -or- If the roller was below 45°C, the heating roller did not reach the ready temperature 2 sec. after reaching 45°C. Note: Thermistor 2 stops monitoring the temperature once Thermistor 1 detects ready temperature. |
| Causes: | • Defective or deformed non-contact thermistor • Incorrect power supply input at the main power socket |
| Remedy: | • Pressure roller thermistor harness loose, disconnected, defective • Pressure roller thermistor defective |
| Error code: | SC553 |
| Description: | Pressure roller thermistor error 3: Software -High temperature. The thermistor detected a temperature over 220°C. |
| Causes: | • Defective main board • Defective PSU |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC554 |
| Description: | Pressure roller thermistor error 4: Hardware - High temperature. The thermistor detected a temperature over 230°C. |
| Causes: | • Defective main board • Defective PSU • Defective fusing unit |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC555 |
| Description: | Pressure roller thermistor error 5: Lamp remains ON. After hot roller reaches warmup temperature, the pressure roller fusing lamp remains for 6 sec. while the hot roller is not rotating. |
| Causes: | The fusing lamp reached the warm-up temperature and then attained fusing temperature (full power), but remained on after paper passed through the fusing unit (hot roller was not rotating). |
| Remedy: | • Thermistor damaged, or out of position • Fusing lamp disconnected, broken Do SP5810 to cancel the SC fusing code. |
| Error code: | SC556 |
| Description: | Heating roller thermistor 2 error 5: Lamp remains ON. After hot roller reaches warmup temperature, the pressure roller fusing lamp remains for 6 sec. while the hot roller is not rotating. |
| Causes: | More than 1 degree Celsius temperature difference (between Center – End thermistor) is detected for 1.5 seconds 5 times in a row. |
| Remedy: | • Thermistor damaged, or out of position • Fusing lamp disconnected, broken |
| Error code: | SC561 |
| Description: | Hot roller thermistor error 1: Thermistor disconnected. The temperature measured by the hot roller thermistor does not reach the prescribed warm-up temperature within 100 sec. |
| Causes: | Temperature detected at less than 0°C. Note: These are the two NC sensors on the side of the fusing unit. |
| Remedy: | • Loose connection of the hot roller thermistor • Defective hot roller thermistor • Defective BICU |
| Error code: | SC562 |
| Description: | Hot roller thermistor error 2: Failure to reach warmup temperature. After the main switch is turned ON or the cover is closed, the heating roller temperature does not reach the ready temperature within 2 sec. after the heater switches ON. -or- If the roller was below 45°C, the heating roller did not reach the ready temperature 2 sec. after reaching 45°C. Note: Thermistor 2 stops monitoring the temperature once Thermistor 1 detects ready temperature. |
| Causes: | Fusing temperature control failed to achieve the warm-up temperature. Note: These are the two NC sensors on the side of the fusing unit. |
| Remedy: | • Hot roller fusing lamp broken • Defective hot roller thermistor • Defective BICU. Do SP5810 to cancel the SC fusing code. |
| Error code: | SC563 |
| Description: | Hot roller thermistor error 3: Software - High Temperature. The thermistor detected a temperature over 250°C 10 times within 1 sec. |
| Causes: | Temperature incorrect due to a TRIAC short or other problem with IOB or AC drive board |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC564 |
| Description: | Hot roller thermistor error 4: Hardware - High Temperature. The thermistor detected a temperature over 260°C. |
| Causes: | Temperature incorrect due to a TRIAC short or other problem with IOB or AC drive board |
| Remedy: | • TRIAC short • IOB defective • BICU defective • Fusing temperature control is erratic Do SP5810 to cancel the SC fusing code. |
| Error code: | SC565 |
| Description: | Hot roller thermistor error 5: Lamp remains ON. After hot roller reaches warmup temperature, the hot roller fusing lamp remains for 6300 sec. while the hot roller is not rotating. |
| Causes: | • Do SP5810 to cancel the SC fusing code. • Thermistor damaged, or out of position • Fusing lamp disconnected, broken |
| Remedy: | • Thermistor damaged, or out of position • Fusing lamp disconnected, broken Do SP5810 to cancel the SC fusing code. |
| Error code: | SC585 |
| Description: | Double-feed sensor error. The output of the double-feed sensor reaches the upper or lower limit |
| Causes: | The fan motor failed to start within the prescribed time or stopped and remained off for one sec. This is the small fan on the right end of the third duct from the top at the rear side of the machine behind the cooling box. |
| Remedy: | • Double-feed sensor connector is not connected correctly. • Double-feed sensor is dirty with paper dust. • There is paper or foreign material between the receptor and LED of the double-feed sensor |
| Error code: | SC620 |
| Description: | ARDF communication error. A BREAK signal occurs after the machine detects the ARDF, or a communication timeout occurs. |
| Causes: | No response from the ADF after connection to the main machine or an error occurred after connection. |
| Remedy: | • ARDF disconnected • IPU board harness disconnected, defective • IPU board defective • Spurious noise from the power supply line • ARDF control board defective |
| Error code: | SC621 |
| Description: | Mailbox-to-Finisher communication error. Communication between the mailbox and finisher is interrupted. An ACK/NCK signal was not received within 100 ms after a data frame is sent and 3 retries failed. |
| Causes: | The UART generated an error when the finisher was connected. |
| Remedy: | • Connection cable between mailbox and finisher disconnected, defective • Finisher main board defective • BICU defective • PSU defective |
| Error code: | SC622 |
| Description: | LCT communication error. Communication between the copier and LCT is interrupted. An ACK/NCK signal was not received within 100 ms after a data frame is sent and 3 retries failed. |
| Causes: | • Paper tray control board defective • BCU defective • IOB defective • Paper tray-main machine connection error |
| Remedy: | • Connection cable between the LCT and copier is disconnected, defective • LCT main board defective • BICU defective • PSU defective |
| Error code: | SC624 |
| Description: | Mailbox-to-copier communication error. Communication between the mailbox and copier is interrupted. An ACK/NCK signal was not received within 100 ms after a data frame is sent and 3 retries failed. |
| Causes: | • Mailbox cable disconnected, defective • Mailbox main board defective • VBCU defective • PSU defective |
| Remedy: | • Mailbox cable disconnected, defective • Mailbox main board defective • BICU defective • PSU defective |
| Error code: | SC630 |
| Description: | RSS communication error. An error was detected in communication via RSS between the machine and the RSS center. Error occurred on a public line at the RSS terminal. |
| Remedy: | • No action required |
| Error code: | SC632 |
| Description: | Key/card counter device error 1. After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • The serial line from the device to the copier is unstable, disconnected, or defective. |
| Remedy: | • The serial line from the device to the copier is unstable, disconnected, or defective. |
| Error code: | SC633 |
| Description: | Key/card counter device error 2. During communication with the device, the BICU received a break (Low) signal. |
| Causes: | • The serial line from the device to the copier is unstable, disconnected, or defective. |
| Remedy: | • The serial line from the device to the copier is unstable, disconnected, or defective. |
| Error code: | SC634 |
| Description: | Key/card counter device error 3. After installation of the device, a message alerts user to a backup RAM error. |
| Causes: | •X Counter device control board defective •X Backup battery of counter device defective |
| Remedy: | • Device control board defective • Device control board backup battery defective |
| Error code: | SC635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Remedy: | • Device control board defective • Device control board backup battery defective |
| Error code: | SC670 |
| Description: | Engine startup error. • Engine does not respond within 30 s after power ON. • Engine down detected suddenly during power ON and warmup. |
| Causes: | The engine failed to communicate with the firmware. Firmware update failure. |
| Remedy: | • BICU installation incorrect • BICU defective • Sudden communication reset occurred between the BICU and the controller. |
| Error code: | SC672 |
| Description: | GW controller startup error. • After power ON, the line between the GW controller and the operation panel did not open for normal operation. • After normal startup, communication with the GW controller stopped. |
| Causes: | • Controller stalled • Board installed incorrectly • Controller board defective • Operation panel connector loose, broken, or defective • Controller late |
| Remedy: | • GW Controller stalled • GW Controller installed incorrectly • GW Controller board defective • Operation panel harness disconnected or defective |
| Error code: | SC680 |
| Description: | BICU-MUSIC communication error. The main CPU fails to communicate with the MUSIC CPU within 5 sec. and three attempts failed. |
| Causes: | • Toner cartridge memory chip loose connection • Memory chip problem • Memory chip cable wiring problem |
| Remedy: | • Toner cartridge ID chip harness disconnected, defective • Toner cartridge ID chip defective • Toner cartridge installed incorrectly • Toner cartridge defective • UART communication failure; replace the BICU |
| Error code: | SC687 |
| Description: | Memory address command error. The BICU does not receive a memory address command from the controller 120 seconds after paper is in the position for registration. |
| Causes: | The BICU did not receive a memory address command from the controller within the prescribed time after the paper reached the registration sensor. |
| Remedy: | • BICU-Controller connection loose, defective • BICU defective • Controller defective |
| Error code: | SC701 |
| Description: | Original pick-up operation error. Even though the pick-up motor is rotating clock-wise, the pick-up roller home position sensor cannot detect the position of the pickup roller. |
| Causes: | Even though the pickup motor is rotating clock-wise, the pickup roller home position sensor cannot detect the position of the pickup roller. |
| Remedy: | • Pick-up roller HP sensor harness loose, disconnected, defective • Pick-up roller HP sensor defective • Pick-up motor harness loose, disconnected, defective • Pick-up motor defective • ARDF control board defective |
| Error code: | SC705 |
| Description: | ARDF bottom plate lift motor. • The bottom plate HP sensor did not detect the home position of the bottom plate after the bottom plate lift motor switches ON and lowers the bottom plate. • The bottom plate position sensor does not detect the position of the plate after the lift motor switches ON and raises the bottom plate. |
| Causes: | The bottom plate HP sensor did not detect the home position of the bottom plate after the bottom plate lift motor switches on and lowers the bottom plate. The bottom plate position sensor does not detect the position of the plate after the lift motor switches on and raises the bottom plate. |
| Remedy: | • ARDF feed motor disconnected, defective • Bottom plate HP sensor disconnected, defective • ARDF main board defective |
| Error code: | SC720 |
| Description: | Finisher lower transport motor error. No encoder pulse signal is detected for the transport motor within the prescribed time. The 1st failure issues an original jam message, and the 2nd failure issues this SC code. |
| Causes: | • Harness short-circuit -80 only • Overload • Motor defective • Solenoid defective -03, -80 only • Connector disconnected • Encoder defective -10, -25, -34 -81 only • Home position sensor defective |
| Remedy: | • Lower transport motor disconnected, defective • Finisher connection to transport motor loose, defective • Lower transport motor defective • Finisher main board defective |
| Error code: | SC721 |
| Description: | Finisher jogger motor error. The jogger fences move out of the home position but the HP sensor output does not change within the specified number of pulses. The 1st failure issues an original jam message, and the 2nd failure issues this SC code. |
| Causes: | • Overcurrent (-03 only) • Staple jam (-44 only) • Encoder error (-11, -11, -25, -44) • Motor defective • Connecter disconnected, or loose • Motor overload • HP sensor defective • Paper surface sensor defective (-70 only) |
| Remedy: | • Jogger HP sensor disconnected, defective • Jogger motor disconnected, defective • Jogger motor overloaded due to obstruction • Finisher main board and jogger motor connection loose, defective • Finisher main board defective |
| Error code: | SC723 |
| Description: | Finisher feed-out motor. The stack feed-out belt HP sensor does not activate within the specified time after the stack feed-out belt motor turns ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The motor that drives the rotation of the positioning sponge roller is not operating. |
| Remedy: | • Stack feed-out HP sensor disconnected, defective • Feed-out motor disconnected, defective • Finisher main board connection to feed out motor disconnected, defective • Motor overload due to obstruction |
| Error code: | SC724 |
| Description: | Finisher stapler hammer motor error. Stapling does not finish within the prescribed time after the staple hammer motor turns ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The motor that lowers and raises the positioning roller above the stapling tray not operating. |
| Remedy: | • Stapler hammer motor overloaded due to obstruction, jammed staple, number of sheets exceeds limit for stapling • Stapler hammer motor disconnected, defective • Staple hammer motor HP sensor disconnected, defective |
| Error code: | SC725 |
| Description: | Finisher exit guide plate motor error. After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The motor that opens and closes the exit guide at the shift tray exit is not operating correctly. |
| Remedy: | • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defective |
| Error code: | SC726 |
| Description: | Shift jogger motor 1 error. The sides fences do not retract within the prescribed time after the shift jogger motor switches ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The drag roller arm with the sponge roller did not return to its home position within the prescribed time. |
| Remedy: | • Shift jogger motor disconnected, defective • Shift jogger motor overloaded due to obstruction • Shift jogger HP sensor disconnected, defective |
| Error code: | SC727 |
| Description: | Shift jogger motor 2 error. The side fences do not retract within the prescribed time after the shift jogger motor switches ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective |
| Error code: | SC728 |
| Description: | Shift jogger retraction motor error. The side fences do not retract within the prescribed time after the retraction motor switches ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The side fences at the exit of the finisher did not leave (or arrive at) their home positions within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective |
| Error code: | SC730 |
| Description: | Finisher Tray 1 shift motor error. The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Error code: | SC740 |
| Description: | Finisher corner stapler motor error. The stapler motor does not switch off within the prescribed time after operating. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The stapler motor did not switch off within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Remedy: | • Staple jam • Number of sheets in the stack exceeds the limit for stapling • Stapler motor disconnected, defective |
| Error code: | SC741 |
| Description: | Finisher corner stapler rotation motor error. The stapler does not return to its home position within the specified time after stapling. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The stapler did not return to its home position (or did not leave its home position) within the specified time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Stapler rotation motor disconnected, defective • Stapler rotation motor overloaded due to obstruction • Stapler rotation HP sensor disconnected, defective |
| Error code: | SC742 |
| Description: | Finisher stapler movement motor error. The stapler HP sensor is not activated within the specified time after the stapler motor turned ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The stapler did not return to its home position (or leave its home position) within the specified time after stapling. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Stapler movement motor disconnected, defective • Stapler movement motor overloaded due to obstruction • Stapler HP sensor disconnected, defective |
| Error code: | SC743 |
| Description: | Booklet stapler motor error 1. The front stapler unit saddlestitch motor does not start operation within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The booklet stapler motor did not start stapling within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Front motor disconnected, defective • Front motor overloaded due to obstruction |
| Error code: | SC744 |
| Description: | Booklet stapler motor error 2. The rear stapler unit saddlestitch motor does not start operation within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Rear motor disconnected, defective • Rear motor overloaded due to obstruction |
| Remedy: | • Rear motor disconnected, defective • Rear motor overloaded due to obstruction |
| Error code: | SC750 |
| Description: | Finisher tray 1 (upper tray lift) motor error. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The shift tray paper height sensor did not change its status within the prescribed time after the tray was raised or lowered. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Tray lift motor disconnected, defective • Upper tray paper height sensor disconnected, defective • Finisher main board connection to motor loose • Finisher main board defective |
| Error code: | SC751 |
| Description: | Finisher tray 2 (lower tray lift) motor error. The lower tray paper height sensor does not change its status with the specified time after the tray raises or lowers. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Tray lift motor disconnected, defective • Upper tray paper height sensor disconnected, defective • Finisher main board connection to motor loose • Finisher main board defective |
| Remedy: | • Tray lift motor disconnected, defective • Upper tray paper height sensor disconnected, defective • Finisher main board connection to motor loose • Finisher main board defective |
| Error code: | SC752 |
| Description: | Finisher pressure plate motor error. Pressure plate motor operating but the plate is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Pressure plate HP sensor disconnected, defective • Pressure plate motor disconnected, defective • Pressure plate motor overloaded due to obstruction |
| Remedy: | • Pressure plate HP sensor disconnected, defective • Pressure plate motor disconnected, defective • Pressure plate motor overloaded due to obstruction |
| Error code: | SC753 |
| Description: | Return roller motor error. Occurs during the operation of the lower tray pressure motor. |
| Causes: | The drag roller HP sensor did not detect the drag roller in (or out of) its home position within the prescribed time. (The drag drive motor drives the timing belt that rotates the drag roller at the shift tray exit.) |
| Remedy: | • Motor harness disconnected, loose, defective • Motor overloaded • Home position sensor harness disconnected, loose, defective • Home position defective |
| Error code: | SC760 |
| Description: | Finisher punch motor error. The punch HP sensor is not activated within the specified time after the punch motor turned ON. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The punch HP sensor did not detect the punch movement motor in (or out) of its home position within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Punch HP sensor disconnected, defective • Punch motor disconnected, defective • Punch motor overload due to obstruction |
| Error code: | SC761 |
| Description: | Finisher folder plate motor error. The folder plate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | 1. Over current of bridge unit motor 2. Over current due to short-circuit in PCB |
| Remedy: | • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction. |
| Error code: | SC762 |
| Description: | Finisher pressure plate motor error. Pressure plate motor operating but the plate is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The punch switch motor failed to turn on within the specified time. |
| Remedy: | • Pressure plate HP sensor disconnected, defective • Pressure plate motor disconnected, defective • Pressure plate motor overloaded due to obstruction |
| Error code: | SC763 |
| Description: | Punch movement motor error. Occurs during operation of the punch unit. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The punch movement HP sensor did not detect the punch at its home position (or out of its home position) within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective |
| Error code: | SC764 |
| Description: | Paper position sensor slide motor error. Occurs during operation of the punch unit. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The system detected an error at the CIS (Contact Image Sensor) inside the punch unit during paper registration for paper punching. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective |
| Error code: | SC765 |
| Description: | Folding unit bottom fence lift motor. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The bottom fence in the booklet fold unit did not return to the home position within the specified time. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective |
| Error code: | SC766 |
| Description: | Clamp roller retraction motor error. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | The clamp roller did not return to the home position within the specified time. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor defective |
| Error code: | SC767 |
| Description: | Stack junction gate motor error. Occurs during operation of the punch unit. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Stack junction mechanism overloaded due to an obstruction • Stack junction gate HP sensor connector loose, broken, defective • Stack junction gate HP sensor defective • Stack junction gate motor connector loose, broken, defective • Stack junction gate motor defective • Main control board defective |
| Remedy: | • Motor harness disconnected, loose, defective • Motor overload • Motor defective |
| Error code: | SC770 |
| Description: | Cover interposer tray bottom plate motor error. • After the motor starts to raise the bottom plate, the bottom plate position sensor does not detect the plate at the specified time (3 s). • After the motor starts to lower the bottom plate, the bottom plate HP sensor does not detect the bottom plate. |
| Causes: | In the first tray: • The upper limit sensor did not detect the bottom plate within the specified time after the lift motor switched on to lift the bottom plate. • The lower limit sensor did not direct the bottom plate within the specified time after the lift motor switched on to lower the bottom plate. Note: In both cases, 1 error count indicates a jam, 2 error counts issue this SC code. |
| Remedy: | • Bottom plate position sensor, disconnected, defective • Bottom plate HP sensor disconnected, defective |
| Error code: | SC775 |
| Description: | Cover interposer tray feed motor |
| Causes: | The top fence HP sensor did not detect the top fence at (or out of) the home position within the prescribed time. The 1st occurrence causes a jam, and the 2nd occurrence causes this SC code. |
| Remedy: | • Motor harness disconnected, loose, defective • Motor overload • Motor defective |
| Error code: | SC780 |
| Description: | Z-Fold feed motor error Japan Only. The feed motor does not attain the prescribed speed within the specified time. |
| Causes: | • Motor harness loose, broken, defective • Motor blocked by an obstruction • Motor defective |
| Remedy: | • Feed motor disconnected, defective • Feed motor overloaded due to obstruction • Feed motor lock |
| Error code: | SC781 |
| Description: | Z-Fold lower stopper motor Japan Only. The lower stopper motor does not attain the prescribed speed within the specified time. |
| Causes: | • Lower stopper motor disconnected, defective • Lower stopper motor overloaded due to obstruction • Lower stopper HP sensor disconnected, defective |
| Remedy: | • Lower stopper motor disconnected, defective • Lower stopper motor overloaded due to obstruction • Lower stopper HP sensor disconnected, defective |
| Error code: | SC782 |
| Description: | Z-Fold upper stopper motor Japan Only. The upper stopper motor does not attain the prescribed speed within the specified time. |
| Causes: | • Upper stopper motor disconnected, defective • Upper stopper motor overloaded due to obstruction • Upper stopper HP sensor disconnected, defective |
| Remedy: | • Upper stopper motor disconnected, defective • Upper stopper motor overloaded due to obstruction • Upper stopper HP sensor disconnected, defective |
| Error code: | SC790 |
| Description: | Finisher staple waste hopper full. The staple waste hopper is full of cut staples. |
| Causes: | The jogger fence HP sensor failed to detect the jogger fence at the home position within the specified time. |
| Remedy: | • If the hopper is full, empty the hopper • If the hopper is not full, the hopper full sensor is disconnected, defective |
| Error code: | SC817 |
| Description: | Boot loader error. The boot loader cannot read one of the following: self-diagnostic module, kernel, or one of the files of the root file system, or the check of one of these items on the system SD card failed. |
| Causes: | • File or module on the system SD card is corrupted • File or module on the system SD card is illegal • Make sure that the system SD card is the one designed for the machine • Replace controller board. |
| Remedy: | • File or module on the system SD card is corrupted • File or module on the system SD card is illegal • Make sure that the system SD card is the one designed for the machine • Replace system ROM on the controller board |
| Error code: | SC818 |
| Description: | Watchdog error. While the system program is running, a bus hold or interrupt program goes into an endless loop, preventing any other programs from executing. |
| Causes: | • System program defective; switch off/on, or change the controller firmware if the problem cannot be solved • Controller board defective • Replace the peripheral device |
| Remedy: | • System program defective; switch OFF/ON, or change the controller firmware if the problem cannot be solved • Controller board defective • Controller option malfunction |
| Error code: | SC819 |
| Description: | Fatal kernel error. Due to a control error, a RAM overflow occurred during system processing. One of the following messages was dis |
| Causes: | • Controller board defective |
| Remedy: | • System program defective • Controller board defective • Optional board defective • Replace controller firmware 0x696e init died 0x766d vm_pageout: Virtual Memory is full 4361 Cache Error NOTE: For more details about this SC code error, execute SP5990 to print an SMC report so you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | SC821-0B00 |
| Description: | Self-diagnostic error 2: ASIC Error code 0xffff ffff is returned when the register Write & Verify check is executed on the ASIC mounted on the controller board. The ASIC controls the ROM and buses for other devices |
| Remedy: | • ASIC (controller board defective) NOTE: For more details about this SC code error, execute SP5990 to print an SMC report so you can read the error code. The error code is not displayed on the operation panel |
| Error code: | SC821-0B06 |
| Description: | Self-diagnostic error 2: ASIC ASIC not detected |
| Remedy: | • ASIC (controller board defective) • Poor connection between North Bridge and PCI I/F: Replace controller board NOTE: For more details about this SC code error, execute SP5990 to print an SMC report so you can read the error code. The error code is not displayed on the operation panel |
| Error code: | SC821-0B10 |
| Description: | Self-diagnostic error 2: ASIC Failed to initialize or could not read connection bus. Data in SHM register incorrect. |
| Remedy: | • Replace controller board NOTE: For more details about this SC code error, execute SP5990 to print an SMC report so you can read the error code. The error code is not displayed on the operation panel |
| Error code: | SC822-3003 |
| Description: | Self-diagnostic error 3: HDD Check performed when HDD is installed |
| Remedy: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | SC822-3004 |
| Description: | Self-diagnostic error 3: HDD No response to the self-diagnostic command from the ASIC to the HDDs |
| Remedy: | • HDD defective |
| Error code: | SC822-3013 |
| Description: | Self-diagnostic error 3: HDD Mandolin does not respond, the HDD device remains BUSY for more than 31 s, or the BUSY signal does not drop within 6 s after the diagnostic command is issued to the HDDs |
| Remedy: | • HDD defective • HDD connector loose or defective • Controller defective |
| Error code: | SC822-3014 |
| Description: | Self-diagnostic error 3: HDD Error returned from HDD in response to the self-diagnostic command, Mandolin could not be located due to a read/write error at the HDD register. |
| Remedy: | • HDD defective |
| Error code: | SC824 |
| Description: | Self-diagnostic error 4: NVRAM NVRAM device does not exist, NVRAM device is damaged, NVRAM socket damaged |
| Causes: | • Controller board detective |
| Remedy: | • NVRAM defective • Controller board defective • NVRAM backup battery exhausted • NVRAM socket damaged |
| Error code: | SC826-1501 |
| Description: | Self-diagnostic error 6: NVRAM (option NVRAM) The difference between the 1 s measured for RTC in the NVRAM and the 1 s timeout of the CPU is out of range, or the NVRAM is not detected. |
| Remedy: | • NVRAM defective • NVRAM installed incorrectly • Replace RTC backup battery |
| Error code: | SC826-15FE |
| Description: | Self-diagnostic error 6: NVRAM (option NVRAM) Backup battery error. Battery is exhausted or not within rated specification. |
| Remedy: | • Replace RTC backup battery |
| Error code: | SC828 |
| Description: | Self-diagnostic error 7: ROM • Measuring the CRC for the boot monitor and operating system program results in an error. • A check of the CRC value for ROMFS of the entire ROM area results in an error. |
| Causes: | A firmware type error or checksum error occurred. |
| Remedy: | • Software defective • Controller board defective • ROM defective NOTE: For more details about this SC 833, SC834 error, execute SP5990 to print an SMC report so you can read the error code. The error code is not displayed on the operation panel. The additional error codes (0F30, 0F31, etc. are listed in the SMC report. |
| Error code: | SC833 |
| Description: | Self-diagnostic error 8: Engine I/F ASIC |
| Remedy: | 0F30 0F31 ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. • Replace the mother board 0F41 The read/write check done for resident RAM on the mother board could not be done correctly. • Replace the mother board 50B1 Could not initialize or read the bus connection. • Check for loose connections at the mother board. • Replace the mother board 50B2 Value of the SSCG register is incorrect. • Check for loose connections at the mother board. • Replace the mother board |
| Error code: | SC834 |
| Description: | Self-diagnostic error 9: Optional Memory RAM DIMM 5101 The write/verify check for the optional RAM chip on the engine mother board gave an error. |
| Causes: | • Controller defective |
| Remedy: | • Controller defective • Mother board defective |
| Error code: | SC850 |
| Description: | Net I/F error. • Duplicate IP addresses. • Illegal IP address. • Driver unstable and cannot be used on the network. |
| Causes: | • IP address setting incorrect • Ethernet board defective • Controller board defective |
| Remedy: | • IP address setting incorrect • Ethernet board defective • Controller board defective |
| Error code: | SC851 |
| Description: | IEEE 1394 I/F error. Driver setting incorrect and cannot be used by the 1394 I/F. |
| Causes: | Driver setting incorrect and cannot be used by the 1394 I/F. |
| Remedy: | • NIB (PHY), LINK module defective; change the Interface Board • Controller board defective |
| Error code: | SC853 |
| Description: | Wireless LAN Error 1. During machine start-up, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | During machine start-up, the machine can access the board that holds the wireless LAN (Bluetooth), but not access the wireless LAN card. |
| Remedy: | • Wireless LAN card missing (was removed) |
| Error code: | SC854 |
| Description: | Wireless LAN Error 2. During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | The board that holds the wireless LAN card (Bluetooth) could be accessed, but the wireless LAN card could not be accessed while the machine was operating. |
| Remedy: | • Wireless LAN card missing (was removed) |
| Error code: | SC855 |
| Description: | Wireless LAN error 3. An error was detected on the wireless LAN card (802.11b or Bluetooth). |
| Causes: | An error was detected for the wireless LAN card (802.11b or Bluetooth). |
| Remedy: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | SC856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN card (802.11b or Bluetooth). |
| Causes: | An error was detected for the wireless LAN board (Bluetooth). |
| Remedy: | • Wireless LAN card defective • PCI connector (to the mother board) loose |
| Error code: | SC857 |
| Description: | USB I/F Error. The USB driver is not stable and caused an error. |
| Causes: | The USB driver is unstable and generated an error. |
| Remedy: | • Bad USB card connection • Replace the controller board |
| Error code: | SC860 |
| Description: | HDD startup error at main power ON. • HDD is connected but a driver error is detected. • The driver does not respond with the status of the HDD within 30 s. |
| Causes: | HDD is connected but a driver error is detected, or the driver did not respond with the status of the HDD within 30 s. |
| Remedy: | • HDD is not formatted • Label name input during formatting is corrupted; format the hard disk again • HDD is defective |
| Error code: | SC861 |
| Description: | HDD re-try failure. At power ON with the HDD detected, power supply to the HDD is interrupted, after the HDD is awakened from the sleep mode, the HDD is not ready within 30 s. |
| Causes: | At power on with the HDD detected, power supply to the HDD is interrupted, after the HDD is awakened from the sleep mode, the HDD is not ready within 30 s. |
| Remedy: | • Harness between HDD and board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | SC863 |
| Description: | HDD data read failure. The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Remedy: | • HDD defective Note: If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM, and the next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. |
| Error code: | SC864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to an CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | During HDD operation, the HDD cannot respond to an CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Remedy: | • HDD defective |
| Error code: | SC865 |
| Description: | HDD access error. HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Remedy: | • HDD defective. |
| Error code: | SC866 |
| Description: | SD card error 1: Confirmation. The machine detects an electronic license error in the application on the SD card in the controller slot immediately after the machine is turned ON. The program on the SD card contains electronic confirmation license data. If the program does not contain this license data, or if the result of the check shows that the license data in the program on the SD card is incorrect, then the checked program cannot execute and this SC code is displayed. |
| Causes: | The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. Note: • The program on the SD card contains electronic confirmation license data. • If the program does not contain this license data, or if the result of the check shows that the license data in the program on the SD card is incorrect, then the checked program cannot execute and this SC code is displayed. |
| Remedy: | • Program missing from the SD card • Download the correct program for the machine to the SD card |
| Error code: | SC867 |
| Description: | SD card error 2: SD card removed. The SD card in the boot slot when the machine was turned on was removed while the machine was ON. |
| Causes: | An application SD card has been removed from the slot (mount point of /mnt/sd*). |
| Remedy: | • Insert the SD card, then turn the machine OFF and ON. |
| Error code: | SC868 |
| Description: | SD card error 3: SD card access. An error occurred while an SD card was used. |
| Causes: | • SD card defective • SD controller defective |
| Remedy: | • SD card not inserted correctly • SD card defective • Controller board defective Note: If you want to try to reformat the SD card, use SD Formatter Ver 1.1. |
| Error code: | SC870 |
| Description: | Address book data error. Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Software bug • Inconsistency of Address Book source location (machine/delivery server/LDAP server) • Inconsistency of Address Book encryption setting or encryption key (NVRAM was replaced individually without formatting the Address Book) • Address Book storage device (SD) was temporarily removed or hardware configuration does not match the application configuration. • Address Book data corruption was detected. |
| Remedy: | • Software defective. Turn the machine OFF/ON. If this is not the solution for the problem, then replace the controller firmware. • HDD defective. More Details • Do SP5846 050 (UCS (User info control service) Settings – Initialize all Directory Info.) to reset all address book data. • Reset the user information with SP5832 006 (HDD Formatting– User Information). • Replace the HDDs. • Boot the machine from the SD card. |
| Error code: | SC873 |
| Description: | HDD mail send data error. An error was detected on the HDD immediately after the machine was turned ON, or power was turned OFF while the machine used the HDD. |
| Causes: | An error was detected on the HDD immediately after the machine was turned on, or power was turned of while the machine was using the HDD. |
| Remedy: | • Do SP5832-007 (Format HDD – Mail TX Data) to initialize the HDD. • Replace the HDD |
| Error code: | SC874 |
| Description: | Delete All error 1: HDD. A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit (B735) running from an SD card. |
| Causes: | • Error detected in HDD data delete program • Error detected in NVRAM data delete program • The "Delete All" option was not set |
| Remedy: | • Turn the main switch OFF/ON and try the operation again. • Install the Data Overwrite Security Unit again. For more, see section “1. Installation”. • HDD defective |
| Error code: | SC875 |
| Description: | Delete All error 2: Data area. An error occurred while the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B660 running from an SD card. |
| Causes: | • HDD logical formatting failed. • The modules failed to erase data. |
| Remedy: | • Turn the main switch OFF/ON and try the operation again. |
| Error code: | SC880 |
| Description: | File Format Converter (MLB) error. A request to get access to the MLB was not answered within the specified time. |
| Causes: | • MLB defective, replace the MLB |
| Remedy: | • MLB defective, replace the MLB |
| Error code: | SC900 |
| Description: | Electrical total counter error. The total counter contains something that is not a number. |
| Causes: | The total counter contains data that is not a number. |
| Remedy: | • NVRAM incorrect type • NVRAM defective • NVRAM data scrambled • Unexpected error from external source |
| Error code: | SC910 |
| Description: | External controller (E-7000) error 1 The external controller (E-7000) sends an error message. |
| Causes: | Refer to the instructions for the external controller |
| Remedy: | • Turn the machine power OFF/ON |
| Error code: | SC911 |
| Description: | External controller (E-7000) error 2 The external controller (E-7000) sends an error message. |
| Remedy: | • Turn the machine power OFF/ON |
| Error code: | SC912 |
| Description: | External controller (E-7000) error 3 The external controller (E-7000) sends an error message. |
| Remedy: | • Turn the machine power OFF/ON |
| Error code: | SC913 |
| Description: | External controller (E-7000) error 4 The external controller (E-7000) sends an error message. |
| Remedy: | • Turn the machine power OFF/ON |
| Error code: | SC914 |
| Description: | External controller (E-7000) error 5 The external controller (E-7000) sends an error message. |
| Remedy: | Turn the machine power OFF/ON |
| Error code: | SC919 |
| Description: | External controller (E-7000) down. An internal application error was detected and operation cannot continue. |
| Causes: | While EAC (External Application Converter), the conversion module, was operating normally, the receipt of a power line interrupt signal from the FLUTE serial driver was detected, or BREAK signal from the other station was detected. |
| Remedy: | • Software defective; turn the machine OFF/ON, or change the controller firmware • Insufficient memory |
| Error code: | SC920 |
| Description: | Printer error 1. An internal application error was detected and operation cannot continue. |
| Causes: | • The software’s bug • Unexpected hardware configuration such as insufficient memory |
| Remedy: | • Software defective; turn the machine OFF/ON, or change the controller firmware • Insufficient memory |
| Error code: | SC921 |
| Description: | Printer error 2. When the application started, the necessary font was not on the SD card. |
| Causes: | When the printer application started, the specified font could not be found on the SD card. |
| Remedy: | • Font not on the SC card |
| Error code: | SC925 |
| Description: | Net File function error. The NetFile file management on the HDD cannot be used, or a NetFile management file is corrupted and operation cannot continue. The HDDs are defective and they cannot be debugged or partitioned, so the Scan Router functions (delivery of received faxes, document capture, etc.), Web services, and other network functions cannot be used. HDD status codes are displayed below: |
| Causes: | The NetFile file management on the HDD cannot be used, or a NetFile management file is corrupted and operation cannot continue. The HDDs are defective and they cannot be debugged or partitioned, so the Scan Router functions (delivery of received faxes, document capture, etc.), Web services, and other network functions cannot be used. HDD status codes are displayed below the SC code: |
| Remedy: | Procedure 1 If the machine shows SC codes for HDD errors (SC860 ~ SC865) with SC 925, do the recovery procedures for SC860 ~ SC865. Procedure 2 If the machine does not show one of the five HDD errors (SC860 ~ SC865), turn the machine power OFF and ON. If this is not the solution for the problem, then initialize the NetFile partition on the HDD with SP5832-011 (HDD Formatting). NetFiles: Jobs printed from the document server using a PC and DeskTopBinder • Before you initialize the NetFile partition on the HDD, tell the customer that: • Received faxes on the delivery server will be erased • All captured documents will be erased • DeskTopBinder job history will be erased • Documents on the document server, and scanned documents, will not be erased. • The first time that the network gets access to the machine, the management information must be configured again (this will use a lot of time). Before you initialize the Netfile partition with SP5832-011, do these steps: 1. Go into the User Tools mode and do “Delivery Settings” to print all received fax documents that are scheduled for delivery. Then erase them. 2. In the User Tools mode, do Document Management> Batch Delete Transfer Documents. 3. Do SP5832-011, then turn the machine power OFF and ON. Procedure 3 If “Procedure 2” is not the solution for the problem, do SP5832-001 (HDD Formatting – All), then turn the machine power OFF and ON. SP5832-001 erases all document and address book data on the hard disks. Ask the customer before you do this SP code. Procedure 4 If “Procedure 3” is not the solution for the problem, replace the HDD. |
| Error code: | SC990 |
| Description: | Software error 2 The software performs an unexpected function and the program cannot continue. |
| Causes: | An unexpected operation was encountered by the software. |
| Remedy: | • Software defective, re-boot 1) Execute SP7403 or print an SMC Report (SP5990) to read the history of the 10 most recent logged errors. 2) If you press the zero key on the operation panel with the SP selection menu displayed, you will see detailed information about the recently logged SC990 or SC991, including the software file name, line number, and so on. 1) is the recommended method, because another SC could write over the information for the previous SC. |
| Error code: | SC991 |
| Description: | Software error 3 The software performs an unexpected function and the program cannot continue. However, unlike SC990, recovery processing allows the program to continue. |
| Causes: | The software peformed an unexpected function and the program cannot continue. Recovery processing allows the program to continue. |
| Remedy: | • Software defective, re-boot 1) Execute SP7403 or print an SMC Report (SP5990) to read the history of the 10 most recent logged errors. 2) If you press the zero key on the operation panel with the SP selection menu displayed, you will see detailed information about the recently logged SC990 or SC991, including the software file name, line number, and so on. 1) is the recommended method, because another SC could write over the information for the previous SC. |
| Error code: | SC992 |
| Description: | Software error 4: Undefined An error not controlled by the system occurred (the error does not come under any other SC code). |
| Causes: | An error not controlled by the system occurred (the error does not come under any other SC code). |
| Remedy: | • Software defective • Turn the machine power OFF and ON. The machine cannot be used until this error is cleared. |
| Error code: | SC997 |
| Description: | Cannot select application function An application does not start after the user pushed the correct key on the operation panel. |
| Causes: | An application did not start after pressing the appropriate key on the operation panel. |
| Remedy: | • Software bug • A RAM or DIMM option necessary for the application is not installed or not installed correctly. |
| Error code: | SC998 |
| Description: | Application cannot start Register processing does not operate for an application within 60 s after the machine power is turned ON. No applications not start correctly, and all end abnormally. |
| Causes: | Register processing did not execute for an application within 60 sec. after the machine was switched on. No applications start correctly, and all end abnormally. |
| Remedy: | • Software bug • A RAM or DIMM option necessary for the application is not installed or not installed correctly. |
