Riso ComColor 3050

Общие характеристики
Макс. формат	A3
Размещение	напольный
Тип	струйный
Технология печати	пьезоэлектрическая струйная
Тип устройства	Принтер
Цветность печати	цветная
Факс
Сканер
Копир
Печать фотографий
Телефон
Пигментные чернила
Двусторонняя печать
Печать без полей
Макс, разрешение для ч/б печати
По X	300
По Y	600
Скорость ч/б печати
A4	90
Стандарт TWAIN
Стандарт WIA
Слайд-адаптер
Отправка изображения по e-mail
Печать на:
Фотобумаге
CD/DVD
Рулоне
Плотность бумаги
Максимальная	210
Минимальная	46
Цветной
Caller ID
Автоответчик
Стандарт DECT
Спикерфон
Проводная трубка
АОН
Беспроводная трубка
Языки управления
PostScript	опционально
PostScript 2
PPDS
PCL 6
PCL 5e
PCL 5c
Подача бумаги
Стандартная	2 500
Вывод бумаги
Стандартный	500
Брошюровщик
Степлер
Сортер
Инфракрасный порт
Wi-Fi
LPT
Bluetooth
FireWire (IEEE 1394)
Устройство для чтения карт памяти
RS-232
Ethernet (RJ-45)
Объем памяти	512
Процессор
Частота процессора	1 860
Емкость жесткого диска	160
Экран
Диагональ дисплея	8,5
Работа от аккумулятора
Поддержка ОС
Windows
Уровень шума
При работе	68
Высота	1 020
Глубина	695
Ширина	1 210
Вес	180

Error code:	I01
Description:	Maintenance call
Causes:	1403 The maintenance call guideline value for printing quantity has been reached
Remedy:	Do one of the following. • Press the Close button. • In test mode 01900, set the maintenance guideline value to 0. Note: To resolve the underlying problem, change the setting in test mode 01900.

Error code:	I02
Description:	Waste ink tank nearly full
Causes:	2062 It is almost time to replace the waste ink tank. Waste ink tank sensor 1 (top): ON Waste ink tank sensor 2 (bottom): ON
Remedy:	Do one of the following. • Press the Close button. • Remove the waste ink tank. • Allow the waste ink tank to become full (the message will be cleared automatically). Note: To resolve the underlying problem, remove and replace the waste ink tank.

Error code:	I03
Description:	Operating in temporary registration status
Causes:	1814 Printer operating in temporary registration mode
Remedy:	Do one of the following. • Press the Close button. • Access test mode 08400 to force official registration of the printer. • Allow the period of temporary registration to expire (the message will be cleared automatically). Note: To resolve the underlying problem, change the setting in test mode 08400.

Error code:	I04
Description:	Unsupported ink
Causes:	2098 1 No ink ejection waveform (parameters) for the loaded black ink 2098 2 No ink ejection waveform (parameters) for the loaded cyan ink 2098 3 No ink ejection waveform (parameters) for the loaded magenta ink 2098 4 No ink ejection waveform (parameters) for the loaded yellow ink
Remedy:	Do one of the following. • Press the Close button. • Remove the relevant ink cartridge. • Update the version of the engine program. Note: To resolve the underlying problem: • Replace the ink with a supported ink cartridge. • Update the program and enter ink ejection parameters compatible with the version of the loaded ink.

Error code:	I05
Display:	I 05 error command [ ]
Description:	Using ink for another model
Causes:	2099 1 Unsupported black ink is installed after the period of temporary registration. 2099 2 Unsupported cyan ink is installed after the period of temporary registration. 2099 3 Unsupported magenta ink is installed after the period of temporary registration. 2099 4 Unsupported yellow ink is installed after the period of temporary registration.
Remedy:	Do one of the following. • Press the Close button. • Remove the relevant ink cartridge. • Allow the period of temporary registration to expire (the message will be cleared automatically). Note: To resolve the underlying problem, replace the ink with ink compatible with machine information.

Error code:	I06
Description:	Outgoing queue nearly full
Causes:	0065 The outgoing queue for online remote functions is nearly full (at 80% capacity).
Remedy:	Do one of the following. • Press the Close button. • Access test mode 00414 to save data for which transmission failed on a USB memory device. Note: To resolve the underlying problem, access test mode 00746, check settings such as settings for communication with the admin server, and establish communication between the online remote server and printer.

Error code:	I08
Description:	BP belt maintenance request
Causes:	0229 1 The CIS is reading the BP belt density to be over 30%. Check the BP belt for ink stains. 0229 2 The paper width or center of the paper detected by CIS is off position over the allowed distance. Check the BP belt for ink stains
Remedy:	Do one of the following. • Press the Close button. Note: To solve the problem, the BP belt should be cleaned of the ink or replaced with a new BP belt..

Error code:	I09
Description:	The machine information and control card information do not match.
Causes:	1936 Wrong Control card maybe inserted. Insert correct Control card. This error message displays during the tentative registration between the Engine control PCB and Control card during the machine installation.
Remedy:	Check the Control card.

Error code:	S01
Description:	BP motor lock
Causes:	The main transport system cannot be controlled appropriately. 202 S01 Transfer belt motor error An alarm signal from the DC servo motor was detected (detection of overcurrent during operations). 203 S01 Transfer belt motion speed error The clock frequency of the belt motor shaft encoder falls outside the specified range. 204 S01 Belt encoder error The frequency input from the belt encoder is below the specified value.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S02
Description:	Elevator motor lock
Causes:	The elevator cannot be controlled appropriately. 104 S02 Elevator motor timeout The upper limit sensor fails to activate when the elevator rising operation is activated within the specified interval. 119 S02 Elevator motor timeout The lower limit sensor fails to activate during a standard paper feed tray lowering operation within the specified interval.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S03
Description:	Belt platen lock
Causes:	The belt platen elevation mechanism cannot be set properly. 200 S03 Transfer belt motor timeout The motor shaft encoder of the transfer belt motor does not attain the specified pulse count within the specified time. The required movement does not complete even when the transfer belt motor operates for the specified interval. 201 S03 Transfer belt unit sensor error The three sensors that determine the position of the belt platen produced an abnormal detection result. 231 S03 Belt platen operation error The upper limit position sensor fails to activate when the belt platen rises. 240 S03 Belt platen operation error The upper limit position sensor fails to deactivate when the belt platen lowers. 241 S03 Belt platen operation error The lower limit position sensor fails to activate when the belt platen lowers. 242 S03 Belt platen operation error The lower limit position sensor fails to deactivate when the belt platen rises. 243 S03 Belt platen operation error The vacuum positioning sensor fails to activate when the belt platen operates. 244 S03 Belt platen operation error The vacuum positioning sensor fails to deactivate when the belt platen operates.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S04
Description:	Head maintenance error
Causes:	Head maintenance cannot be controlled appropriately. Including waste ink tank full condition. 300 S04 Ink pan motor timeout The right or left sensor fails to activate within the specified interval. 301 S04 Ink pan sensor error The right and left sensors activate at the same time. 302 S04 Cleaning motor timeout The detection plate does not reach the suction nozzle HP sensor even when the motor operates for the specified interval to move the cleaning motor to the retraction position on the front side. Or the suction nozzle HP sensor fails to deactivate when it moves from the HP. 303 S04 Suction chamber full The suction chamber sensor is turned ON. 300 S04 Ink pan motor timeout The right or left sensor fails to activate within the specified interval. 301 S04 Ink pan sensor error The right and left sensors activate at the same time. 302 S04 Cleaning motor timeout The detection plate does not reach the suction nozzle HP sensor even when the motor operates for the specified interval to move the cleaning motor to the retraction position on the front side. Or the suction nozzle HP sensor fails to deactivate when it moves from the HP. 303 S04 Suction chamber full The suction chamber sensor is turned ON. 305 S04 Suction pump rotation speed error The rotation speed of the suction pump falls outside the specified range (checked by the encoder clock frequency for the specified time). 307 S04 Overflow tank full Ink is detected by the overflow sensor. 321 S04 Pressure pump motor timeout The logic of the pressure pump sensor (detection at motor 180-degree intervals) does not change even when the pressure pump motor is driven for a certain time period. 344 S04 Cleaning motor timeout 2 HP sensor does not go ON even after the motor rotates for the specific time period to move the cleaning motor to the front retracting position. 345 S04 Error on the Cleaning Motor When the cleaning motor rotated, the pulse count was below the parameter after completion of moving. 346 S04 Cleaning motor timeout 3 HP sensor does not go OFF even after the motor rotates for the specific time period to move the cleaning motor to the rear.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S05
Description:	Head thermistor error
Causes:	Head temperature control is malfunctioning. 311 S05 Disconnection in head thermistor The head temperature could not be measured correctly. When the reading of the thermistor is -86.9 °C * Head identification information (K1 - Y6) is added after the error point. 312 S05 Head abnormally hot The head temperature exceeded 80 °C. When the reading of the thermistor is 80.0 °C * Head identification information (K1 - Y6) is added after the error point. 313 S05 Head cooling timeout The temperature remained above 45 °C for 10 minutes. When the monitored head temperature remains 45 °C or more for 10 minutes * Head identification information (K1 - Y6) is added after the error point.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S06
Description:	Ink heating error
Causes:	Ink heating control is malfunctioning. 314 S06 Ink heating timeout When the temperature of ink in the distributor meets the following conditions after being heated for a set time: 1) & either 2), 3) 4), 5), 6) or 7) 1) The temperature is less than 15 °C. 2) It takes more than 360 seconds to raise the temperature by 1 °C after the heater has been powered on. 3) It takes more than 600 seconds to raise the temperature by 4 °C after the heater has been powered on. 4) It takes more than 750 seconds to raise the temperature by 7 °C after the heater has been powered on. 5) It takes more than 900 seconds to raise the temperature by 10 °C after the heater has been powered on. 6) It takes more than 1,320 seconds to raise the temperature by 13 °C after the heater has been powered on. 7) A temperature of less than 15 °C holds for more than 1,800 seconds. * Head identification information (K, C, M, Y) is added after the error point.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S07
Description:	Ink cooling error
Causes:	Ink cooling control is malfunctioning. 319 S07 Ink cooling timeout The temperature of ink being distributed remains 40 °C for five minutes. * Ink identification information (K, C, M, Y) is added after the error point.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S10
Description:	Multi-tray paper feed error
Causes:	A service error is generated in the multi-tray paper feed. 400 S10 FL transfer motor lock (Detailed No. 1: timeout) There was no input interrupt from the FL transfer motor FG sensor during FL transfer motor operation, even after the specified time elapsed. 402 S10 Feed tray 1 elevator motor lock (Detailed No. 1: timeout) The FL feed tray 1 upper limit sensor fails to activate after the FL feed tray 1 elevator motor turns ON, even after the specified time elapses. * This error can be cleared by opening feed tray 1. 403 S10 Feed tray 1 elevator motor lock (Detailed No. 2: overcurrent) An overcurrent was detected in the FL feed tray 1 elevator motor. * This error can be cleared by opening feed tray 1. 404 S10 Feed tray 2 elevator motor lock (Detailed No. 1: timeout) The FL feed tray 2 upper limit sensor fails to activate after the FL feed tray 2 elevator motor turns ON even after the specified time elapses. * This error can be cleared by opening feed tray 2. 405 S10 Feed tray 2 elevator motor lock (Detailed No. 2: overcurrent) Overcurrent was detected in the FL feed tray 2 elevator motor. * This error can be cleared by opening feed tray 2. 406 S10 Feed tray 1 paper width adjustment parameter error The correction value for the feed tray 1 paper width VR falls outside the specified range. * This error can be cleared by opening the feed tray or opening the cover of the vertical transfer unit. 407 S10 Feed tray 2 paper width adjustment parameter error The correction value for the feed tray 2 paper width VR falls outside the specified range. * This error can be cleared by opening the feed tray or opening the cover of the vertical transfer unit. 408 S10 Multi-tray paper feed multiple feed sensor light emitting intensity error The multiple feed sensor light emitting intensity falls outside the specified range. * This error can be cleared by opening the feed tray or opening the cover of the vertical transfer unit. 409 S10 Multi-tray paper feed EEPROM error Data could not be written correctly to the EEPROM. Or an EEPROM checksum error occurred. * This error can be cleared by opening the feed tray or opening the cover of the vertical transfer unit.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S11
Description:	Paper feed motor lock
Causes:	The paper feed motor cannot be controlled appropriately.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S12
Description:	Exit motor lock
Causes:	The exit motor cannot be controlled appropriately. 100 S12 Exit motor encoder error The encoder frequency input from the exit motor unit deviates from the theoretical value. 102 S12 Wing motor timeout The wings do not reach the HP when they are operated for a period of time corresponding to the distance of travel. 103 S12 Wing motor timeout The wing HP sensor does not detect the movement of the wings from the HP when they are operated for the specified interval.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S13
Description:	Blower fan lock
Causes:	The blower fans cannot be controlled appropriately.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S14
Description:	Waste ink tank error
Causes:	The waste ink tank is full. 323 S14 (Y02) Water ink tank full The waste ink tank is detected as full.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S19
Description:	Interface module error
Causes:	3000 After operation is started, the decurler home sensor is not deactivated in time. 3001 After operation is started, the decurler home sensor is not activated in time.
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S20
Description:	Puncher unit error
Causes:	3002 After operation is started, the puncher home sensor is not activated in time. 3003 After operation is started, the puncher home sensor is not deactivated in time. 3004 After operation is started, the puncher move home sensor is not deactivated in time. 3005 After operation is started, the puncher move home sensor is not activated in time. 3006 After operation is started, the side registration home sensor is not deactivated in time. 3007 After operation is started, the side registration home sensor is not activated in time.
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S28
Description:	Paper elevation motor locked
Causes:	1039 Paper elevation motor locked error
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S29
Description:	Upper transfer motor locked
Causes:	1040 Paper elevation motor locked error
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S30
Description:	Switchback motor locked
Causes:	1041 Switchback motor locked error
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S31
Description:	Re-feed motor locked
Causes:	1042 Re-feed motor locked error
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S32
Description:	Ink pan error
Causes:	2020 The ink pan was retracted, but the ink pan storage sensor was not activated. 2021 The ink pan was retracted, but the ink pan operating position sensor was not deactivated. 2022 The ink pan was moved to the operating position, but the ink pan storage sensor was not deactivated. 2023 The ink pan was moved to the operating position, but the ink pan operating position sensor was not activated. 2024 Ink pan operations were done, but they were not completed in time. 2025 The ink pan storage sensor and ink pan operating position sensor were both activated at once.
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S33
Description:	Wiper action error
Causes:	2030 The wiper moved towards the back, but the wiper motor HP sensor did not go ON. 2031 The wiper moved towards the front, but the wiper motor HP sensor did not go OFF.. 2032 The wiper moved forward, but did not move for the given distance. 2033 Wiper drive was not finished in time.
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S34
Description:	Ink cartridge unit error
Causes:	2040 The authorization cam was moved to the home position, but the authorization cam HP sensor was not activated. 2041 The authorization cam was moved, but the printer did not detect activation of the authorization cam HP sensor in time.
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S35
Description:	Ink supply unit error
Causes:	2050 The bellows arm was raised to the upper limit position, but the bellows arm upper position sensor was not activated. 2051 The bellows arm was moved to the home position, but the bellows arm HP sensor was not activated. 2052 The bellows arm was lowered to the lower limit position, but the bellows arm lower position sensor was not activated. 2053 The bellows arm drive did not stop in time. 2054 Two or more of the following sensors were activated at the same time: bellows arm upper position sensor, bellows arm HP sensor, and bellows arm lower position sensor. 2055 The bellows sensor was activated during ink circulation. 2056 The bellows arm motor was driven, but the printer detected that it did not move. 2060 The overflow tank ink sensor is activated. 2064 The pressurized ink tank ink sensors are not activated. 2065 Abnormal ink temperature values were acquired during cleaning. 2066 Ink circulation was not finished in time. 2067 Activate signal was given to the Ink circulation motor, but is detected not activated. 2069 1 Pressurized ink tank ink sensor K was not activated even once as the printer detected no black ink three times. 2069 2 Pressurized ink tank ink sensor K remained OFF for more than a particular number of cycles despite circulation (printing pressure). 2070 1 Pressurized ink tank ink sensor C was not activated even once as the printer detected no cyan ink three times. 2070 2 Pressurized ink tank ink sensor C remained OFF for more than a particular number of cycles, despite circulation (printing pressure). 2071 1 Pressurized ink tank ink sensor M was not activated even once as the printer detected no magenta ink three times. 2071 2 Pressurized ink tank ink sensor M remained OFF for more than a particular number of cycles, despite circulation (printing pressure). 2072 1 Pressurized ink tank ink sensor Y was not activated even once as the printer detected no yellow ink three times. 2072 2 Pressurized ink tank ink sensor Y remained OFF for more than a particular number of cycles, despite circulation (printing pressure). 2073 1 Negative pressure ink tank ink sensor K remained OFF, despite circulation (printing pressure). 2073 2 Negative pressure ink tank ink sensor K remained ON, despite circulation (printing pressure). 2074 1 Negative pressure ink tank ink sensor C remained OFF, despite circulation (printing pressure). 2074 2 Negative pressure ink tank ink sensor C remained ON, despite circulation (printing pressure). 2075 1 Negative pressure ink tank ink sensor M remained OFF, despite circulation (printing pressure). 2075 2 Negative pressure ink tank ink sensor M remained ON, despite circulation (printing pressure). 2076 1 Negative pressure ink tank ink sensor Y remained OFF, despite circulation (printing pressure). 2076 2 Negative pressure ink tank ink sensor Y remained ON, despite circulation (printing pressure). 2077 The negative pressure ink tank air valve was not open when circulation stopped (under atmospheric pressure).
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S36
Description:	Ink circulation pump error
Causes:	2068 1 The black ink circulation pump is not connected or there is a problem with it. 2068 2 The cyan ink circulation pump is not connected or there is a problem with it. 2068 3 The magenta ink circulation pump is not connected or there is a problem with it. 2068 4 The yellow ink circulation pump is not connected or there is a problem with it. 2078 1 There is a control problem with the black ink circulation pump. 2078 2 There is a control problem with the cyan ink circulation pump. 2078 3 There is a control problem with the magenta ink circulation pump. 2078 4 There is a control problem with the yellow ink circulation pump.
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S37
Description:	Belt profile input error
Causes:	11 40 Incorrect numbers were entered for nos. 1–3 during belt profile data input in test mode. 11 41 Incorrect numbers were entered for nos. 4–6 during belt profile data input in test mode. 11 42 Incorrect numbers were entered for nos. 7–9 during belt profile data input in test mode. 11 43 Incorrect numbers were entered for nos. 10–12 during belt profile data input in test mode.
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S39
Description:	Head thermistor temperature-reading error
Causes:	2164 1 The head temperature thermistor on the KC head control PCB may be disconnected, or there may be a poor connection. 2164 2 The head temperature thermistor on the MY head control PCB may be disconnected, or there may be a poor connection.
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S40
Description:	BP Belt encoder data receive error
Causes:	11 53 The BP belt encoder count was not correctly received.
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S90
Description:	Machine information set error
Causes:	1813 The combination of values that the user is attempting to enter (specification information, model class, and printing information) are not valid as machine information.
Remedy:	Press the <Close> button

Error code:	S91
Description:	Software error 2
Causes:	0035 During communication for initialization immediately after the printer was turned ON, device control information (including machine code) was not sent from the engine to the PMS in time.
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S92
Description:	Firmware error
Causes:	0045 Incompletely downloaded firmware on the panel, because downloading failed 1920 Downloading of some engine firmware is not finished.
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S93
Description:	Test mode execution error
Causes:	0167 1 Completion notification status error for machine sequence manager system 0167 2 Completion notification status error for print sequence manager system 0167 3 Completion notification status error for transfer control SS 0167 4 Completion notification status error for finisher SS 0167 5 Completion notification status error for count SS 0167 6 Completion notification status error for RFID tag SS
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	S94
Description:	Download error (loader)
Causes:	Communication error or data error during downloading.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S95
Description:	Download error
Causes:	Communication error or data error during downloading. 045 S95 Download error (HC Control PCB detection) An error was detected on the HC Control PCB side during a download. 046 S95 Download error (IP PCB detection) An error was detected on the IP PCB side during a download. 047 S95 Download error (MC PCB detection) An error was detected on the MC PCB side during a download. 054 S95 Error in the downloaded data. Error in the downloading data received.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S96
Description:	PCB or hardware disconnection
Causes:	The PCB is not connected. 001 S96 Power supply remote signal not connected The control signal cable for the ON/OFF control of the 24/38-VDC output is disconnected. The signal wire grounded inside the power supply unit has been pulled up by the IP PCB to detect the level. 008 S96 Control panel not connected The absence of the control panel unit to be connected to the MC PCB is detected. Since this configuration lacks this panel, this error indication will not be issued under normal operating circumstances. 009 S96 Print counter not connected The absence of a print counter is detected. 011 S96 CIS PCB not connected The connection of the CIS PCB cannot be confirmed. 013 S96 K head driver PCB not connected The connection of the K color head driver PCB cannot be confirmed with the connection detection signal. 014 S96 C head driver PCB not connected The connection of the C color head driver PCB cannot be confirmed with the connection detection signal. 015 S96 M head driver PCB not connected The connection of the M color head driver PCB cannot be confirmed with the connection detection signal. 016 S96 Y head driver PCB not connected The connection of the Y color head driver PCB cannot be confirmed with the connection detection signal. 028 S96 ORCNL PCB on machine left side not connected The connection of the ORCNL PCB on the machine left side cannot be confirmed. 029 S96 HC Control PCB timeout The Busy signal on the HC control PCB will not be deactivated upon the start of communication from the MC PCB. 042 S96 R/W PCB failure 3 Connection signal timeout (The PCB is not connected.) 043 S96 HC Control PCB not connected The connection of the HC Control PCB cannot be confirmed. (The HC Control PCB READY signal cannot be confirmed when the IP PCB is powered on.) 113 S96 Pickup clutch not connected The connection of the pickup clutch cannot be confirmed. 114 S96 Registration clutch not connected The connection of the registration clutch cannot be confirmed. 115 S96 Registration brake not connected The connection of the registration brake cannot be confirmed. 121 S96 Dust fan 1 not connected Connection of dust fan 1 cannot be confirmed. 122 S96 Dust fan 2 not connected Connection of dust fan 2 cannot be confirmed. 205 S96 Blower fan 1 disconnected/not connected The connector for blower fan 1 is disconnected, or there is a break in the winding. 206 S96 Blower fan 2 disconnected/not connected The connector for blower fan 2 is disconnected, or there is a break in the winding. 207 S96 Blower fan 3 disconnected/not connected The connector for blower fan 3 is disconnected, or there is a break in the winding. 208 S96 Blower fan 4 disconnected/not connected The connector for blower fan 4 is disconnected, or there is a break in the winding. 232 S96 Belt platen elevator clutch not connected The connection of the belt platen elevator clutch cannot be confirmed. 233 S96 Gate solenoid not connected The connection of the gate solenoid cannot be confirmed. 234 S96 Duplex transport not connected The connection of the duplex clutch cannot be confirmed. 235 S96 Re-feed pickup clutch not connected The connection of the re-feed pickup clutch cannot be confirmed. 236 S96 Re-feed brake not connected The connection of the re-feed brake cannot be confirmed. 239 S96 Switchback clutch not connected The connection of the switchback clutch cannot be confirmed. 304 S96 Suction chamber sensor not connected 308 S96 Overflow tank not connected The connection of the overflow sensor cannot be confirmed. 309 S96 Cooling fan 1 not connected 310 S96 Cooling fan 2 not connected 316 S96 Reservoir not connected * Ink identification information (K, C, M, Y) is added after the error point. 317 S96 ID unit air open valve not connected * Ink identification information (K, C, M, Y) is added after the error point. 318 S96 Distributor unit not connected * Unit identification information (KC, MY) is added after the error point. 322 S96 (Z12) Waste ink tank not installed The waste ink tank is not installed.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S97
Description:	Power supply error
Causes:	There is a problem with the power supply. 003 S97 38-VDC power supply voltage error A voltage drop is detected when a voltage drop is sensed by the IP PCB based on the signal resulting from dividing the 38-VDC resistance inside the power supply unit. The detection level is approximately 18 VDC. Voltage polling is conducted at 100-ms intervals by the IP-CPU. An error is detected when a voltage drop is sensed 10 times in succession (approx. 1 sec). No detection is performed when the interlock SW is open. 004 S97 24-VDC power supply voltage error A voltage drop is detected when a voltage drop is sensed by the IP PCB based on the signal resulting from dividing the 24-VDC resistance inside the power supply unit. The detection level is approximately 11 VDC. Voltage polling is conducted at 100-ms intervals by the IP-CPU. An error is detected when a voltage drop is sensed 10 times in succession (approx. 1 sec). No detection is performed when the interlock SW is open. 006 S97 3.3-VDC power supply voltage error A voltage drop is detected when a voltage drop is sensed in the 3.3-VDC power supply on the MIP side of the IP PCB. Voltage polling is conducted at 100-ms intervals by the IP-CPU. An error is detected when a voltage drop is sensed 10 times in succession (approx. 1 sec). 007 S97 1.8-VDC power supply voltage error A voltage drop is detected when a voltage drop is sensed in the 1.8-VDC power supply on the MIP side of the IP PCB. Voltage polling is conducted at 100-ms intervals by the IP-CPU. An error is detected when a voltage drop is sensed 10 times in succession (approx. 1 sec).
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S98
Description:	Hardware error
Causes:	The hardware cannot be controlled appropriately. 012 S98 IP PCB not connected (communication error) The IP PCB is not connected. Since the MC PCB receives its power from the IP PCB, this error indication will not be issued under normal operating circumstances. 017 S98 Control panel LCD error An error was detected in the panel LCD drive chip. Since the LCD driver will not operate when this error occurs, this error indication will not be issued under normal operating circumstances. 018 S98 K head driver PCB error Head Driver PCB error is indicated when: A head driver PCB configuration error has occurred. A failure by the MIP to respond to a data request from the head driver PCB has been detected. A communication error between the head driver PCB and IP has been detected. A 38-V voltage error in the head driver PCB has been detected. 019 S98 C head driver PCB error Same as when detecting a K head driver PCB error. 020 S98 M head driver PCB error Same as when detecting a K head driver PCB error. 021 S98 Y head driver PCB error Same as when detecting a K head driver PCB error. 022 S98 MC PCB FPGA program error Improper operation of the FPGA program on the MC PCB was detected. 023 S98 IP PCB MIP program error. MIP configuration on the main PCB failed. 024 S98 IP PCB SPLD program error SPLD configuration on the main PCB failed. 040 S98 R/W PCB failure 1 Initial communication with the R/W PCB failed. 041 S98 R/W PCB failure 2 Run signal timeout 052 S98 Date/time setting error The date/time is not set correctly. The clock is set with a date predating the PLIP firmware release date. Or the clock is set with a date postdating the year 2030. 058 S98 Error on NVRAM. Error with NVRAM on the machine. 101 S98 Multiple feed sensor error A change in light intensity does not change the amount of light received at power ON or during initialization to reset a multiple feed error. * This error can be cleared by the panel setting [Multiple feed detection OFF]. 245 S98 Error in Image Adjustment Paper size used in Image Adjustment is out of the range. Or the scanned data by the CCD is wrong (out of the range).
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	S99
Description:	Software error
Causes:	For debugging 025 S99 For debugging: A DC startup report does not arrive from the IP-CPU within the specified time. 026 S99 For debugging: The IP-CPU does not respond to the sensor monitor demand from the MC-CPU. 027 S99 For debugging: The IP-CPU does not respond to the SQR from the MC-CPU. 031 S99 Multi-tray paper feed communication error 1 Multi-tray paper feed power line error 032 S99 Multi-tray paper feed timeout The machine status command transmitted from the paper feed device on the base was outside the specified range (phase error). Or the [Preparation complete] status command was not received within the specified interval after receiving the [Preparing] status command. 033 S99 Multi-tray paper feed communication error 1 The machine status command was not received from the paper feed device on the base within the specified interval (when the papaer feed device on the base does not respond). 034 S99 Multi-tray paper feed communication error 2 Base paper feed initialization information completion command was not received within the specified time of 1 second after the base paper feed initialization command was issued. 035 S99 Multi-tray paper feed communication error 3 Status information could not be transmitted during communications with the auto fence function within the specified interval. 036 S99 Auto fence communication error A Test mode status command was not received before the elapse of the specified interval after the transmission of the Test mode execution command. 037 S99 Multi-tray paper feed communication error 2 Multi-tray paper feed communication transmission error 038 S99 Multi-tray paper feed communication error 3 Multi-tray paper feed communication reception break error 039 S99 Multi-tray paper feed communication error 4 Multi-tray paper feed communication transmission buffer error 044 S99 HC Control PCB communication error (timeout error) A command from the HC Control PCB was not received during the HC Control-MC communication within the specified interval. 048 S99 FRAM checksum error FRAM checksum error of the HC Control PCB 049 S99 FRAM read verify error The data does not match data read from the FRAM of the HC Control PCB. 050 S99 FRAM write verify error The data does not match data written to the FRAM of the HC Control PCB. 053 S99 FRAM access error The FRAM of the HC Control PCB could not be accessed normally. 055 S99 Machine information software error. Error detected by the HC Control PCB while processing the machine type data. 056 S99 Machine software error (debug error) 057 S99 Communication error between IP-MC PCBs. Error between IP-MC PCBs during communication. 340 S99 Ink tag software error (For debugging) * Ink identification information (K, C, M, Y) is added after the error point.
Remedy:	<>Reset power, or execute [Clear error] in Test mode. <>Some errors (such as PCB disconnection) may not be cleared by executing [Clear error]. <>Even if an S error occurs, it may be possible to continue operations using another unit. Therefore, certain error types require a specific reset procedure (described in Error Point).

Error code:	U01
Description:	CLOSE FRONT COVER
Causes:	0063 The USB connection is Full-Speed (12 Mbps), not Hi-Speed (480 Mbps). 0202 During communication with the scanner, the scanner did not respond. 0219 The scanner is disconnected or OFF. 0220 No scanner firmware 4120 The USB connection is Full-Speed (12 Mbps), not Hi-Speed (480 Mbps). 4121 The USB cable was disconnected during image data transfer.
Remedy:	1. Front Cover is open. 2. Front Cover Sensor is disconnected. 3. Front Cover Sensor is defective. 4. LVPS connector is disconnected. 5. LVPS is defective. 6. Engine PCB is defective.

Error code:	U02
Description:	Scanner communication error
Causes:	0201 During communication with the scanner, an unspecified command was received from scanner. 0203 The scanning parameters are incorrect. 0205 The scanner communication program failed to allocate memory. 0207 Data for testing scanner data monitoring could not be written. 0209 Scanner rev. data could not read or written. 0210 Scanner information file could not be opened. 0211 Image file from the scanner could not be opened. 0213 Image data from the scanner could not be saved. 0215 Image data could not be received from the scanner. 0216 Data for printing could not be received from the scanner. 0217 Error on the Scanner. 0218 The next original could not be detected within 30 seconds during AF scanning. 0221 Incorrect version of command for scanner communication 4200 Data transfer failed between the controller and scanner, due to a bad USB connection, timeout, or other reasons. 4201 Scanning could not be started from the controller when the next original was determined to be ready in communication between the controller and scanner.
Remedy:	Press the Reset key, or turn OFF the printer. (Turn OFF the printer through sub power key.) It may also be possible to clear the error as follows: • Reconnect the scanner. • Restart the scanner.

Error code:	U03
Description:	FB error
Causes:	4300 Scanner operation was not finished in time. 4301 In carriage operation expected to deactivate the HP sensor on completion, the HP sensor was not deactivated in time. 4302 In carriage operation expected to activate the HP sensor on completion, the HP sensor was not activated in time. 4303 The carriage setting value for the amount of movement or the frequency was out of range. 4310 Timeout waiting for black shading 4311 Timeout waiting for white shading 4316 After the scanner lamp was activated, the maximum time to keep the lamp ON per scanning job was exceeded and the lamp remains ON. 4320 Data after offset adjustment is smaller than the minimum value or greater than the maximum value. 4321 Timeout waiting for offset adjustment 4322 Data after gain adjustment is smaller than the minimum value or greater than the maximum value. 4323 Timeout waiting for gain adjustment 4500 When the test mode for checking data in DDR memory was accessed, an error occurred in the first stage of the DDR memory. 4501 When RGB data was checked in the test mode for checking data in DDR memory, an error occurred in the second stage of the DDR memory. 4502 When gray data was checked in the test mode for checking data in DDR memory, an error occurred in the second stage of the DDR memory.
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	U04
Description:	AF error
Causes:	4420 The AF is not connected. ("AF version 0" is sent in initial communication to the controller.) 4430 There is no AF program (issued from AF side). 4440 Failed to adjust the sensitivity of the AF original IN sensor (issued from AF side) 4441 The AF fan motor is not working (issued from AF side). 4470 AF operation was not restored from power save mode in time (not detected when the AF is not connected).
Remedy:	Press the Reset key, or turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	U05
Description:	AF communication error
Causes:	4450 Scanner–AF communication: An operation request was sent by the scanner when 24V was not supplied to the AF. 4461 Scanner–AF communication: AF initialization failed following communication failure after three attempts by the scanner. 4462 In scanner–AF communication, transmission by the scanner was not finished. 4463 In scanner–AF communication, a sequence error occurred (control signal error).
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	U06
Description:	Scanner locked settings error
Causes:	4330 Scanner locked settings prevent operation.
Remedy:	Press the Reset key, or turn OFF the printer. (Turn OFF the printer through sub power key.) Note: To resolve the underlying problem, access test mode 05715 and set the scanner locked setting to 0 (operation allowed).

Error code:	U07
Description:	Scanner EEPROM error
Causes:	4130 The serial number stored in EEPROM has not been set. 4131 The test mode setting values stored in EEPROM are out of range. 4132 The default image processing setting values stored in EEPROM are out of range.
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	U08
Description:	Scanner profiling data error
Causes:	4360 Scanner profiling data is not stored in flash memory after the scanner starts up. 4361 Valid profiling data was not generated when profiling mode was accessed in test mode.
Remedy:	Press the Reset key, or turn OFF the printer. (Turn OFF the printer through sub power key.) Note: To resolve the underlying problem, access test mode 5406 (scanner profiling mode) to store scanner profiling data in flash memory. If the error persists, cool off the unit and access test mode 5406 again.

Error code:	U11
Description:	Imaging Unit Fan Failure
Causes:	• Imaging Unit Fan, PL6.1.23 • IDFAN Harness, PL5.1.31 • GTG0 Harness, PL5.1.32
Remedy:	1 Test the Imaging Unit Fan. Run the Service Diagnostics Imaging Unit Fan test. Does the Fan operate correctly. Replace the Engine Control Board. Go to Step 2. 2 Check the Fan connection. Is P/J100 securely connected? Replace the Fan. If the error persists, go to Step 3. Connect the Fan. 3 Check for +24 V at the Fan. Disconnect P/J100. Is there +24 V between J100-1 <=> ground? Go to Step 4. Go to Step 5. 4 Check continuity of the IDFAN Harness. Is the wiring harness conductive? Go to Step 5. Replace the harness. 5 Check for +24 V at the Imaging Unit Sensor Board. Disconnect CTG0. Is there +24 V at CTG0-9? Replace the Imaging Unit Sensor Board. Go to Step 6. 6 Check continuity of the CTG0 Harness. Is the wiring harness conductive? Replace the Engine Control Board Replace the harness.

Error code:	U12
Display:	U12-Duplex I/F Error
Description:	Duplex Interface Failure Error occurs only after the detection of a properly installed and functioning Duplex Unit.
Causes:	• Duplex Unit, PL16.1.0 • Motor Driver Board, PL2.1.10
Remedy:	1 Check the Duplex Unit connector for damage. Is the connector damaged? Replace the connector. Replace the Duplex Unit. If the error persists, go to Step 2. 2 Check all pins on the DUPLEX Harness for continuity. Disconnect the DUPLEX Harness. Is the DUPLEX Harness conductive? Replace the Motor Driver Board. If the error persists, go to Step 3. Replace the DUPLEX Harness. 3 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness.

Error code:	U14
Display:	U14-Tray 2 I/F Error
Description:	An error has been detected with the Tray 2 interface and communication path. Turn off the printer, wait 15 seconds, then turn on the printer.
Causes:	3079 After operation was started, end guide home sensor 1 was not deactivated in time. 3080 After operation was started, end guide home sensor 2 was not deactivated in time. 3081 After operation was started, end guide home sensor 1 was not activated in time. 3082 After operation was started, end guide home sensor 2 was not activated in time. 3083 After the tray latch solenoid was activated, the envelope folder tray interlock switch was not deactivated in time.
Remedy:	1. Turn the printer off and then on. 2. Inspect the interface connector connecting the tray unit to the print engine. Inspect the printer’s corresponding connector on the underside of the printer. Inspect the wiring harness leading from the connector to the engine control board. 3. Replace the engine controller board.

Error code:	U16
Description:	NO CARTRIDGE
Causes:	3084 After stack tray lowering or raising began, the stack height sensor was not deactivated in time. 3085 Stacking tray beyond upper limit position 3086 Stacking tray beyond lower limit position
Remedy:	1. No Toner Cartridge.

Error code:	U17
Description:	Booklet tray error
Causes:	3087 After operation was started, the front booklet tamper home sensor was not activated in time. 3088 After operation was started, the front booklet tamper home sensor was not deactivated in time. 3089 After operation was started, the booklet end guide home sensor was not deactivated in time. 3090 After operation was started, the booklet end guide home sensor was not activated in time. 3091 After operation was started, the rear booklet tamper home sensor was not activated in time. 3092 After operation was started, the rear booklet tamper home sensor was not deactivated in time. 3093 After operation was started, the knife folding sensor was not activated in time. 3094 When the front cover was closed, the booklet drawer set sensor was deactivated. 3095 After operation was started, the booklet knife home sensor was not activated in time. 3096 After operation was started, the booklet knife home sensor was not deactivated in time. 3097 The stapler did not work after the booklet stapler start signal was sent.
Remedy:	Press the Reset key, or turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	U18
Description:	Scanner custom color profile data error
Causes:	4230 Color profile data has not been downloaded to the custom area.
Remedy:	Press the Reset key, or turn OFF the printer. (Turn OFF the printer through sub power key.) Note: To resolve the underlying problem, access test mode 05803 and set the color profile selection to 0 (standard).

Error code:	U93
Description:	External controller error
Causes:	5001 The external controller hard disk is full. There is less than 1 GB of free space, and subsequent jobs cannot be processed. 5002 The external controller hard disk is corrupted. The file system check (fsck) conducted when the external controller starts up has detected an unrecoverable error. 5003 The external controller hard disk drive can no longer operate correctly. 5004 There is no dongle in the external controller, or the inserted dongle conforms to regional specifications other than those for the hard disk drive (for example, a Japanese-specification hard disk drive is used with a dongle for overseas use). 5005 Cannot communicate with the external controller (detected by the controller PCB unit) 5006 Communication (transmission) is possible with the external controller, but it does not follow the correct sequence (detected by the external controller). 5007 Communication (reception) is possible with the external controller, but it does not follow the correct sequence (detected by the controller PCB unit). 5008 A power OFF command is sent from the SEN to the external controller, but the external controller is not deactivated (detected by the controller PCB unit). Wait time is one minute. 5009 When scanned data cannot be received correctly by the external controller (detected by the controller PCB unit)
Remedy:	Press the Reset key, or turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	U98
Description:	Scanner hardware error
Causes:	4150 Failed to write to flash memory 4180 FPGA configuration failed in the first or second stage. 4190 Time-out occurred after image data could not be produced by the image processing chip. 4210 Downloading the image processing DSP firmware failed. 4211 The startup response from the image processing DSP was not completed in time. 4212 The shutdown response from the image processing DSP was not completed in time. 4213 The exchange of commands between the image processing DSP and host was not completed in time. 4214 The transmission purpose code for commands sent from the host to the image processing DSP was undefined. 4215 The parameter code for commands sent from the host to the image processing DSP was undefined. 4216 There were too many data elements in the table sent from the host to the image processing DSP. 4217 There were too few data elements in the table sent from the host to the image processing DSP. 4218 The host received an undefined command from the image processing DSP. 4340 CCD PCB setup processing failed. 4341 Time-out waiting for SSI transmission interrupt request SSI transmission timing Data sent to the A/D converter (written) Data sent to the CCD PCB (written) Data received from the CCD PCB (read) 4350 Scanner fan does not revolve
Remedy:	Turn OFF the printer. (Turn OFF the printer through sub power key.)

Error code:	U99
Description:	Operation control PWB communication error Communication error between the operation control PWB and the MCU PWB (Detected by the OPE-PWB)
Causes:	Disconnection or reverse connection of the flat cable between the Operation control PWB and the MCU PWB. Operation control PWB trouble MCU PWB trouble Connector trouble of the operation control PWB and the MCU PWB

Error code:	W01
Description:	Paper change
Causes:	No paper (When any tray is empty) 116 W01 No paper All feed trays are empty.
Remedy:	Set paper in one of the feed trays.

Error code:	W02
Description:	No paper (Standard paper feed tray)
Causes:	The standard paper feed tray is empty when paper feed is selected. 110 W02 No paper in standard paper feed tray The standard paper feed tray is empty when it is selected as the feed tray.
Remedy:	Press the Cancel key on the panel. Or load the applicable feed tray with paper. Or select another feed tray (Menu 6). Or clear the print job (Menu 7).

Error code:	W03
Description:	No paper (Feed tray 1)
Causes:	The feed tray 1 is empty when paper feed is selected. 433 W03 Feed tray 1 no paper Although selected as the current feed tray, feed tray 1 is currently empty.
Remedy:	Press the Cancel key on the panel. Or load the applicable feed tray with paper. Or select another feed tray (Menu 6). Or clear the print job (Menu 7).

Error code:	W04
Description:	No paper (Feed tray 2)
Causes:	The feed tray 2 is empty when paper feed is selected. 434 W04 Feed tray 2 no paper Although selected as the current feed tray, feed tray 2 is currently empty.
Remedy:	Press the Cancel key on the panel. Or load the applicable feed tray with paper. Or select another feed tray (Menu 6). Or clear the print job (Menu 7).

Error code:	W05
Description:	No paper (Auto)
Causes:	The auto feed tray selected is empty. 117 W05 No paper (auto) None of the trays contain the required type of paper when auto feed tray is selected.
Remedy:	Press the Cancel key on the panel. Or load the applicable feed tray with paper. Or select another feed tray (Menu 6). Or clear the print job (Menu 7).

Error code:	W06
Description:	No separation sheets inserted between print jobs
Causes:	No paper is available when the sorting function is selected. 118 W06 No separation sheets inserted between print jobs The separation paper feed tray has run out of paper during a sorting operation. Or the separation paper feed tray is empty at the beginning of a sorted printing operation.
Remedy:	Press the Cancel key on the panel. Or load paper on the Sorting Tray. Or disable the sorting function. Or switch to another tray from the Sorting Tray (Menu 5.3). Or clear the print job (Menu 7).

Error code:	W07
Description:	Auto fence operation not possible
Causes:	The auto fence function is invalid. Press the Cancel key on the panel. 501 W07 Paper guide HP reset timeout The paper guide HP sensor fails to activate during a paper guide HP reset. 502 W07 Paper guide HP failure timeout The paper guide HP sensor fails to deactivate during movement of paper guide. 503 W07 Paper guide limit position movement timeout The paper guide limit sensor fails to activate when the paper guides move to their limit positions. 504 W07 Paper guide limit position failure timeout The paper guide limit sensor fails to deactivate during movement of paper guide. 505 W07 Paper stopper HP reset timeout The paper stopper HP sensor fails to activate during paper stopper HP reset. 506 W07 Paper stopper HP position failure timeout The paper stopper HP sensor fails to deactivate during movement of paper stopper. 507 W07 Paper stopper limit position failure timeout The paper stopper limit sensor fails to activate when the paper stopper moves to its limit position. 508 W07 Paper stopper limit position failure timeout The paper stopper limit sensor fails to deactivate during movement of paper stopper.
Remedy:	Or disable the auto fence function (Menu 4.8.2).

Error code:	W08
Description:	Controller HDD full
Causes:	The HDD of the controller is full. 513 W08 PS7R controller HDD full. PS7R controller HDD fully used.
Remedy:	Delete unnecessary data from the HDD. Or the error is automatically cleared when free space is available on the HDD. *The error appears while processing a new job, but when the error occurs, the processing job is automatically deleted, so the error message also resets automatically.

Error code:	W09
Description:	No cover paper loaded
Causes:	1013 1 No paper loaded in the front cover sheet tray when attempting to feed paper for the front cover (error detected by controller). 1013 2 No paper loaded in the front cover sheet tray when attempting to feed paper for the front cover (error detected by engine control). 1014 1 No paper loaded in the back cover sheet tray when attempting to feed paper for the back cover (error detected by controller). 1014 2 No paper loaded in the back cover sheet tray when attempting to feed paper for the back cover (error detected by engine control).
Remedy:	Do one of the following. • Load paper of any size in the cover tray. • Press the Cancel button. • Delete the job.

Error code:	W10
Description:	Top tray full
Causes:	3220 1 The top tray has almost reached the stacking limit (detected by finisher). 3220 2 The top tray has almost reached the stacking limit (detected by printer).
Remedy:	Do one of the following. • Press the Cancel button. • Delete the job.

Error code:	W11
Display:	W11-Tray 1 Paper Low
Description:	The printer has detected that the paper level in Tray 1 is low. Printing can continue until the tray runs out of paper. Reload the tray as soon as possible to avoid printing interruptions.
Causes:	3221 1 The stacking tray has almost reached the stacking limit for standard paper (detected by finisher). 3221 2 The stacking tray has almost reached the stacking limit for standard paper (detected by printer). 3222 1 The stacking tray has almost reached the stacking limit for stapled paper (detected by finisher). 3222 2 The stacking tray has almost reached the stacking limit for stapled paper (detected by printer).

Error code:	W12
Display:	W12-Tray 2 Paper Low
Description:	The printer has detected that the paper level in Tray 2 is low. Printing can continue until the tray runs out of paper. Reload the tray as soon as possible to avoid printing interruptions.
Causes:	3223 1 The booklet tray has almost reached the stacking limit (detected by finisher). 3223 2 The booklet tray has almost reached the stacking limit (detected by printer).

Error code:	W13
Display:	W13-Tray 3 Paper Low
Description:	The printer has detected that the paper level in Tray 3 is low. Printing can continue until the tray runs out of paper. Reload the tray as soon as possible to avoid printing interruptions.
Causes:	3224 1 The 3-fold tray has almost reached the stacking limit (detected by finisher). 3224 2 The 3-fold tray has almost reached the stacking limit (detected by printer).

Error code:	W14
Description:	Envelope setting error
Causes:	0240 Duplex printing or straight ejection by face-down printing is specified for Envelope printing.
Remedy:	Do one of the following. • Press the Select tray button and switch to a tray other than the tray specified for envelope feeding. • Press the Select tray button and change the paper feed settings of the tray in use to settings other than for envelopes. • Press the Cancel button. • Delete the job.

Error code:	W16
Display:	Fuse Cut Error
Description:	Fuse Cut Error In Fuser The in-use fuse for the indicated Fuser remains intact.
Causes:	• Fuser, PL1.1.21
Remedy:	1 Test the Fuser fuse. Run the Service Diagnostics Read Fuse test on the Fuser. Is the Fuse Cut? Replace the Engine Control Board. Go to Step 2. 2 Replace the Fuser. Cycle the power. Does the error persist? Go to Step 3. Complete. 3 Check all pins of the HEATIF harness between the Fuser and Engine Control Board. Is the HEATIF harness conductive? Replace the Engine Control Board.

Error code:	W17
Description:	Fuse Cut Error In Transfer Unit The in-use fuse for the indicated Transfer Unit remains intact.
Causes:	• Transfer Unit, PL1.1.20 • HVPS Cover, PL2.1.27 • HVPS, PL2.1.26
Remedy:	1 Test the condition of the fuse. Run the Service Diagnostics Read Fuse test for the TBelt. Is the Fuse cut? Replace the Engine Control Board. Go to Step 2. 2 Check the connections between HVPS, HVPS Cover, and Transfer Unit. Are the contacts clean and intact? Install a new Transfer Unit and verify the fuse blows. Clean or align contacts as needed. If the error persists, go to Step 3. 3 Does the error persist? Replace in the following order: HVPS Cover HVPS. Complete

Error code:	W18
Description:	Specified paper size not supported
Causes:	1006 1-2 During paper transfer when jobs are started or resumed, the specified output paper size is not supported under specifications of the specified destination for ejection. Variation code: 1 : Error detected by controller or related components; 2: Error detected by engine or related components
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W19
Description:	Restart finisher
Causes:	3235 Finisher must be restarted
Remedy:	Press the Close button. Note: Pressing the Close button will clear the error itself, but the finisher must be restarted before revised settings take effect.

Error code:	W20
Description:	Scratch sheets in top tray
Causes:	3231 Paper was ejected to the top tray before printing was finished.
Remedy:	Do one of the following. • Press the Continue button. • Press the Cancel button. • Delete the job.

Error code:	W21
Description:	Scratch sheets in stacking tray
Causes:	3232 Paper was ejected to the stacking tray before printing was finished.
Remedy:	Do one of the following. • Press the Continue button. • Press the Cancel button. • Delete the job.

Error code:	W22
Description:	Scratch sheets in booklet tray
Causes:	3233 Paper was ejected to the booklet tray before printing was finished.
Remedy:	Do one of the following. • Press the Continue button. • Press the Cancel button. • Delete the job.

Error code:	W23
Description:	Scratch sheets in 3-fold tray
Causes:	3234 Paper was ejected to the 3-fold tray before printing was finished.
Remedy:	Do one of the following. • Press the Continue button. • Press the Cancel button. • Delete the job.

Error code:	W24
Description:	FD paper receiving tray full
Causes:	11 50 The printer has detected that the face down paper receiving tray is full.
Remedy:	Do one of the following. • Press the Cancel button. • Delete the job.

Error code:	W25
Description:	Stapler unit not connected
Causes:	3225 A job was sent specifying stapling, but the stapler unit is not connected to the finisher.
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W26
Description:	Puncher unit not connected
Causes:	3226 A job was sent specifying punching, but the puncher unit is not connected to the finisher.
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W27
Description:	Top tray not connected
Causes:	3227 A job was sent specifying ejection to the top tray, but the top tray is not connected to the finisher.
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W28
Description:	Stacking tray not connected
Causes:	3228 A job was sent specifying ejection to the stacking tray, but the stacking tray is not connected to the finisher.
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W29
Description:	Booklet tray not connected
Causes:	3229 A job was sent specifying the booklet tray as the destination, but the booklet tray is not connected to the finisher.
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W30
Description:	3-fold tray not connected
Causes:	3230 A job was sent specifying the 3-fold tray as the destination, but the 3-fold tray is not connected to the finisher
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W31
Description:	Cannot lower stacking tray
Causes:	3125 1-2 Failed to lower stacking tray 3236 1 The tray-lowering safety mechanism for the stacking tray was activated (detected by finisher). 3236 2 The tray-lowering safety mechanism for the stacking tray was activated (detected by printer).
Remedy:	Do one of the following. • Release the tray-lowering safety mechanism for the stacking tray. • Press the Cancel button. • Delete the job.

Error code:	W32
Description:	Stapler unit not available
Causes:	3237 A job was sent specifying stapling, but the stapler unit cannot be used on the finisher.
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W33
Description:	Puncher unit not available
Causes:	3238 A job was sent specifying punching, but the puncher unit cannot be used on the finisher.
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W34
Description:	Top tray not available
Causes:	3239 A job was sent specifying use of the top tray, but the top tray cannot be used on the finisher.
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W35
Description:	Stacking tray not available
Causes:	3240 A job was sent specifying use of the stacking tray, but the stacking tray cannot be used on the finisher.
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W36
Description:	Booklet tray not available
Causes:	3241 A job was sent specifying use of the booklet tray, but the booklet tray cannot be used on the finisher.
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W37
Description:	3-fold tray not available
Causes:	3242 A job was sent specifying use of the 3-fold tray, but the 3-fold tray on the finisher is not available.
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W38
Description:	Cannot apply print job settings
Causes:	0153 Print job settings received from a higher-level module cannot be processed.
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W39
Description:	No destination for continuous output
Causes:	11 54 During continuous output, all paper receiving trays specified to switch to are full, so there is no available paper receiving tray.
Remedy:	Do one of the following. • Press the Cancel button. • Delete the job.

Error code:	W40
Description:	Paused job deleted
Causes:	0222 A paused job was deleted through the console when the settings window for the job was displayed by pressing the Confirm or Setting chg. button.
Remedy:	Press the Close button.

Error code:	W41
Description:	AS paper full detected
Causes:	11 51 The printer has detected that the auto stacking tray is full.
Remedy:	Do one of the following. • Press the Cancel button. • Delete the job.

Error code:	W42
Description:	FDO paper full detected
Causes:	Do one of the following. • Press the Cancel button. • Delete the job.
Remedy:	11 52 The printer has detected that the face down offset output tray is full.

Error code:	W43
Description:	Specified size not loaded in slip sheet tray
Causes:	1015 1 No paper of supported size loaded in the slip sheet tray (error detected by controller) 1015 2 No paper of supported size loaded in the slip sheet tray (error detected by engine control)
Remedy:	Do one of the following. • Load paper of the correct size in the slip sheet tray. • Press the Cancel button. • Delete the job.

Error code:	W44
Description:	Specified size not loaded in cover tray
Causes:	1016 1 No cover paper of the same type and size as this set* is loaded. When Z folding is activated, paper of the correct size after Z folding (error detected by controller) 1016 2 No cover paper of the same type and size as this set is loaded. When Z folding is activated, paper of the correct size after Z folding (error detected by engine control) 1017 1 No back cover paper of the same type and size as this set is loaded. When Z folding is activated, paper of the correct size after Z folding (error detected by controller) 1017 2 No back cover paper of the same type and size as this set is loaded. *When Z folding is activated, paper of the correct size after Z folding (error detected by engine control)
Remedy:	Do one of the following. • Load paper of the correct size in the cover tray. • Press the Cancel button. • Delete the job.

Error code:	W45
Description:	Unsupported combination of paper sizes
Causes:	1004 1-2 During paper transfer, jobs are started or resumed with a combination of sizes other than A4 Landscape and A3, B5 Landscape and B4, or Letter Landscape and Ledger with all of the following settings. • Mixed size ON • Z folding activated • Input tray: Auto Variation code: 1: Error detected by controller or related components; 2: Error detected by engine or related components
Remedy:	Do one of the following. • Press the Close button. • Delete the job.

Error code:	W46
Description:	No tray for auto feed tray selection
Causes:	1018 1 When the input tray selection is Auto, the setting Auto selection is deactivated for all trays (error detected by controller). 1018 2 When the input tray selection is Auto, the setting Auto selection is deactivated for all trays (error detected by engine control).
Remedy:	Do one of the following. • Press the Select tray button and manually specify the tray. • Add a tray candidate for auto tray selection. • Press the Cancel button. • Delete the job.

Error code:	W47
Description:	Image adjustment failed
Causes:	0224 Invalid calibration pattern scanned by the scanner when executing image adjustment in test mode
Remedy:	Press the Close button.

Error code:	W48
Description:	Duplicate file names on USB memory device
Causes:	0060 1-5 When users attempt to save files on the USB memory device, the printer found files with the same name on the device. Variation code: 1: Account record list (log), 2: Job charge count, 3: Details count, 4: Limit qty. summary list, 5: Data for which online transmission failed
Remedy:	Do one of the following. • Press the Continue button. • Press the Cancel button.

Error code:	W49
Description:	No available file names on USB memory device
Causes:	0061 1-2 When users attempt to save files on a USB memory device, all available file names have been used on the device (all files already exist on the device). Variation code: 1: Scan file, 2: Rev.
Remedy:	Press the Close button.

Error code:	W50
Description:	Insufficient USB memory capacity
Causes:	0062 1 Because there is insufficient free space on the USB memory device, files (scan files) cannot be saved on the device. 0062 2 Because there is insufficient free space on the USB memory device, files (other than scan files) cannot be saved on the device.
Remedy:	Do one of the following. • Press the Cancel button. • Press the Save to Internal HDD button. • Press the Retry button. If the message is displayed when attempting to save a scan file (error point variation code 1), you can also do the following. • Press the Save to Internal HDD button.

Error code:	W51
Description:	Request to start recovery operations
Causes:	1301 When the belt platen must be lowered to recover from a paper jam, this message is issued when user confirmation is required.
Remedy:	Press the Confirm button.

Error code:	W53
Description:	USB memory mounting error
Causes:	0053 1 The USB memory device could not be mounted when scanning began (for scan files). 0053 2 The USB memory device could not be mounted when scanning began (for files other than scan files). 0054 1 Could not write to USB memory device (scan files) 0054 2 Could not write to USB memory device (files other than scan files) 0058 1 The USB memory device could not be mounted when exporting rev. or system log data (for scan files) 0058 2 The USB memory device could not be mounted when exporting rev. or system log data (for files other than scan files).
Remedy:	Do one of the following. • Disconnect the USB memory device. • Press the Cancel button. • Press the Save to Internal HDD button. • Press the Retry button.

Error code:	W54
Description:	Email transmission failed
Causes:	0230 1-3 Email transmission failed because there is no destination. Variation code: 1-550 (No destination mailbox), 2-551 (User does not exist), 3-553 (Invalid destination mailbox name) 0231 1-3 Bad mail server settings caused mail transmission failure. Variation code: 1-432 (Password change required), 2-534 (Authentication mechanism too vulnerable), 3-535 (Authentication error) 0232 Excessive allocation of memory on the mail server caused mail transmission failure. The SMTP response code indicating the transmission error (552: Excessive client memory allocation) 0233 1-8 A problem with the mail server caused mail transmission failure. Variation code: 1-421 (Service temporary unavailable), 2-450 (mailbox temporary unavailable), 3-451 (Local server error), 4-452 (Insufficient file system memory), 5-454 (temporary authentication failure), 6-521 (Mail rejected), 7-530 (Access denied), 8-554 (Other processing failure) 0234 1-6 A problem with data for transmission caused mail transmission failure. Variation code: 1-500 (Syntax error), 2-501 (Parameter error), 3-502 (Command not available), 4-503 (Invalid command order), 5-504 (Command parameter not implemented), 6-538 (Requested authentication mechanism requires encryption)
Remedy:	Press the Close button.

Error code:	W56
Description:	Check paper size setting
Causes:	1300 The paper size detected by the system does not match the detected size of paper being transferred. 3243 Paper larger than 488 mm is specified for use with the finisher.
Remedy:	Press the Close button.

Error code:	W57
Description:	Adjustment values not saved
Causes:	0172 With test mode 1497 (save adjustment values) not executed, the test mode area could not be cleared or defaults could not be restored.
Remedy:	Press the Close button.

Error code:	W58
Description:	CIS auto adjustment failed
Causes:	0225 1 During CIS shading compensation or when checking CIS operation, the reference voltage (Vblank) of the left CIS in back was not read correctly. 0225 2 During CIS shading compensation or when checking CIS operation, the reference voltage (Vblank) of the right CIS in front was not read correctly. 0225 3 During CIS shading compensation or when checking CIS operation, the reference voltage (Vblank) of the right and left CIS devices was not read correctly. 0226 1 During left CIS shading compensation, standard paper (lightweight Riso paper) was not loaded in the specified position. 0226 2 During right CIS shading compensation, standard paper (lightweight Riso paper) was not loaded in the specified position. 0226 3 During left and right CIS shading compensation, standard paper (lightweight Riso paper) was not loaded in the specified position. 0226 4 During CIS shading compensation, standard paper (lightweight Riso paper) was not detected. 0227 1 After left CIS shading compensation, the CIS output level could not be adjusted in a range of ±5%. 0227 2 After right CIS shading compensation, the CIS output level could not be adjusted in a range of ±5%. 0227 3 After left and right CIS shading compensation, the CIS output level could not be adjusted in a range of ±5%.
Remedy:	Press the Close button.

Error code:	W59
Description:	CIS operation check failed
Causes:	0228 1 The edge could not be detected during confirmation of left CIS operation. 0228 2 The edge could not be detected during confirmation of right CIS operation. 0228 3 The edge could not be detected during confirmation of left and right CIS operation.
Remedy:	Press the Close button.

Error code:	W60
Description:	Failed to connect to scanning destination server
Causes:	0235 The connection with the scanning destination server was lost because there is no account on the server or the server address is invalid. 0236 Transmission to the scanning destination server failed because of a communication error with the scanning destination or because timeout occurred. 0237 Invalid scanning destination settings Note: Unsupported characters may have been used in the scanning destination address, for example.
Remedy:	Press the Close button.

Error code:	W61
Description:	Cannot save scan file on server
Causes:	0238 When users attempt to save scan files at the scanning destination, all available file names have been used (the files are already saved on the server), so the scan files cannot be saved on the server.
Remedy:	Press the Close button.

Error code:	W62
Description:	Press Power button
Causes:	0078 Because writing the Auto Power On flag failed when downloading firmware other than firmware for the panel, the printer could not start up automatically. Note: The firmware was downloaded successfully.
Remedy:	Press the Start button. Note: When the printer is automatically deactivated after completion of downloading, it cannot be restarted automatically, so press the Power button to start it.

Error code:	W63
Description:	Main power re-boot
Causes:	0079 After downloading the Panel firmware, when main switch of the machine is switched ON later, the machine boots up without pressing the power switch on the operation panel. Note: The firmware was downloaded successfully.
Remedy:	Press the Close button. Then re-boot the machine.

Error code:	W64
Description:	HDD initialization error
Causes:	0242 During the system rebooting, HDD cannot initialize.
Remedy:	Press the Close button.

Error code:	W66
Description:	External CI connection error
Causes:	0243 When archive store is selected without external CI connected, the archive, even though not stored, error message is not displayed.
Remedy:	Press the Close button.

Error code:	W67
Description:	RA (Remove Agent) communication error
Causes:	0244 1 Communication error with the Remove Agent server. < Network not connected (no ping). > 0244 2 Communication error with the Remove Agent server. < Able to communicate with the Remove agent server, but time-out error occurs. >
Remedy:	Press the Close button.

Error code:	W68
Description:	BP Belt stain detected
Causes:	0245 Belt stain is detected by CIS when printing started.
Remedy:	Press <Continue> or <Cancel> button. Delete the print job.

Error code:	W69
Description:	Paper Feed Tray not ready
Causes:	1935 Belt stain is detected by CIS when printing started.
Remedy:	Press <Confirm> button.

Error code:	W70
Description:	Test Mode action not completed
Causes:	0247 1 Unable to execute test modes due to exclusive condition. 0247 2 Error finish due to wrong Control card installed on the machine. 0247 3 Executed test mode ended in error. In many cases, if test modes are executed while the ink temperature is controlled (ink in circulation), this error is displayed. 0252 Speed auto-adjustment failed. The error is displayed when parameter over or under the specified range is input.
Remedy:	Press Close button.

Error code:	W71
Description:	Incompletely printed paper may have been ejected.
Causes:	1937 In paper jam, the last sheet ejected out may be incompletely printed.
Remedy:	Remove jammed papers. Check printed papers. Resume printing.

Error code:	W98
Description:	Check panel settings
Causes:	0077 There is a software bug in an external interface subsystem.
Remedy:	Press the Close button.

Error code:	W99
Description:	Head maintenance
Causes:	Confirming head maintenance execution 315 W99 ID unit low liquid level Low liquid level is detected in the ID unit of each color ink. * Ink identification information (K, C, M, Y) is added after the error point.
Remedy:	Perform head maintenance (normal).

Error code:	X01
Description:	Paper jam in paper feed section
Causes:	Paper jammed between the first paper feed section and the second paper feed section. Jammed paper must be removed from the standard paper feed tray side. 106 X01 Standard paper feed tray feed failure (no paper transport) The registration sensor fails to activate when the specified number of clock inputs is issued from the belt encoder after paper transport from the standard paper feed tray begins.
Remedy:	Open and close the main unit cover, or press the Cancel key on the control panel.

Error code:	X06
Description:	Paper jam in duplex switchback entry section.
Causes:	Paper jammed in the duplex switchback entry section. 222 X06 Switchback sensor paper end exiting delay (in paper vacuum positioning operation) The trailing edge of the paper sheet does not pass the switchback sensor (sensor detecting the presence of paper) within the specified interval based on the belt encoder pulse count. 228 X06 Jammed paper at switchback sensor section when the cover is closed The switchback sensor detects paper when the cover is closed or during the interval in which the paper transport roller idling is controlled when the cover is closed.
Remedy:	Remove all sheets from the paper transport path except for the vertical transfer unit, then close the main unit cover. (This error is automatically cleared if there is no paper on the paper transport path when the recovery operation is activated by opening and closing the main unit cover.)

Error code:	X07
Description:	Paper jam in switchback section.
Causes:	Paper jammed in the switchback section. 209 X07 Duplex re-feed unit failure The registration sensor fails to activate when the specified number of clock inputs is issued from the belt encoder after paper is re-fed for duplex printing.
Remedy:	Remove all sheets from the paper transport path except for the vertical transfer unit, then close the main unit cover. (This error is automatically cleared if there is no paper on the paper transport path when the recovery operation is activated by opening and closing the main unit cover.)

Error code:	X08
Description:	Paper jam in re-feed unit
Causes:	Paper jammed in the re-feed unit.
Remedy:	Remove all sheets from the paper transport path except for the vertical transfer unit, then close the main unit cover. (This error is automatically cleared if there is no paper on the paper transport path when the recovery operation is activated by opening and closing the main unit cover.)

Error code:	X09
Description:	Paper jam in feed tray 1
Causes:	Paper jammed in feed tray 1 431 X09 Feed tray 1 no paper transport FL feed sensor 3 did not turn on when FL feed tray 1 pickup clutch turned ON and the FL transfer motor FG sensor attained the specified pulse count while paper was being fed from feed tray 1.
Remedy:	Open and close feed tray 1.

Error code:	X10
Description:	Paper jam in feed tray 2
Causes:	Paper jammed in feed tray 2 432 X10 Feed tray 2 no paper transport FL feed sensor 1 failed to activate when FL feed tray 2 pickup clutch turned ON and the FL transfer motor FG sensor attained the specified pulse count while paper was being fed from feed tray 2.
Remedy:	Open and close feed tray 2.

Error code:	X11
Description:	Paper jam in vertical path upper section
Causes:	Paper jammed in the upper section of the vertical path. 414 X11 Feed tray 1 paper feed failure The registration sensor fails to activate when the specified number of clock inputs is issued from the belt encoder after paper transport from feed tray 1 begins. 415 X11 Feed tray 2 paper feed failure The registration sensor fails to activate when the specified number of clock inputs is issued from the belt encoder after paper transport from feed tray 2 begins. 425 X11 Multi-tray paper feed jam (Detailed No. 10: S3) FL transfer sensor 4 failed to activate when the FL transfer motor FG sensor attained the specified pulse count after FL feed sensor 3 activated during a paper feed operation. (FL feed sensors 1 and 2 remained OFF, and FL feed sensor 3 remained activated.) Or FL feed sensor 3 remained activated at power ON or in standby mode. 426 X11 Multi-tray paper feed jam (Detailed No. 11: S34) The registration sensor failed to activate when the FL transfer motor FG sensor attained the specified pulse count after FL feed sensor 4 activated during a paper feed operation. (FL feed sensors 1 and 2 remained OFF, and FL feed sensors 3 and 4 remained activated.) Or FL feed sensors 3 and 4 remained activated at power ON or in standby mode. 427 X11 Multi-tray paper feed jam (Detailed No. 12: S34R) Feed sensors 3 and 4, and the registration sensor remained activated at power ON or in standby mode. 428 X11 Multi-tray paper feed jam (Detailed No. 13: S4) The registration sensor failed to activate when the FL transfer motor FG sensor attained the specified pulse count after FL feed sensor 4 activated during a paper feed operation. (FL feed sensors 1 through 3 remained OFF, and FL feed sensor 4 remained activated.) Or FL feed sensor 4 remained activated at power ON or in standby mode. 429 X11 Multi-tray paper feed jam (Detailed No. 14: S4R) Feed sensor 4 and the registration sensor remained activated at power ON or in standby mode. 430 X11 Feed tray 1 separation error The FL multi-tray pickup sensor activated at the feed tray 1 paper feed timing or on receiving a feed tray setting command. 444 X11 Release request command timeout Release request command was not issued by the main unit within the specified interval after notification of completion of paper feeding from a tray.
Remedy:	(This error is cleared if FL feed sensors 1 through 4 are OFF when the door of the vertical transfer unit is opened and closed, or the jam release safety SW switches OFF/ ON.)

Error code:	X12
Description:	Paper jam in vertical path lower section
Causes:	Paper jammed in the lower section of the vertical path 416 X12 Multi-tray paper feed jam (Detailed No. 1: S1) FL transfer sensor 2 failed to activate when the FL transfer motor FG sensor attained the specified pulse count after FL feed sensor 1 activated during a paper feed operation. (FL feed sensor 1 remained activated.) Or FL feed sensor 1 remained activated at power ON or in standby mode. 417 X12 Multi-tray paper feed jam (Detailed No. 2: S12) FL transfer sensor 3 failed to activate when the FL transfer motor FG sensor attained the specified pulse count after FL feed sensor 2 activated during a paper feed operation. (FL feed sensors 1 and 2 remained activated.) Or FL feed sensors 1 and 2 remained activated at power ON or in standby mode. 418 X12 Multi-tray paper feed jam (Detailed No. 3: S123) FL transfer sensor 4 failed to activate when the FL transfer motor FG sensor attained the specified pulse count after FL feed sensor 3 turned ON during a paper feed operation. (FL feed sensors 1, 2, and 3 remained activated.) Or FL feed sensors 1, 2, and 3 remained activated at power ON or in standby mode. 422 X12 Multi-tray paper feed jam (Detailed No. 7: S23) FL transfer sensor 4 failed to activate when the FL transfer motor FG sensor attained the specified pulse count after FL feed sensor 3 activated during a paper feed operation. (FL feed sensor 1 remained OFF, and FL feed sensors 2 and 3 remained activated.) Or FL feed sensors 2 and 3 remained activated at power ON or in standby mode. 443 X12 Feed tray 2 separation error The FL transfer sensor 1 activated at the feed tray 2 paper feed timing or on receiving a feed tray setting command.
Remedy:	(This error is cleared if FL feed sensors 1 through 4 are OFF when the door of the vertical transfer unit is opened and closed, or the jam release safety SW switches OFF/ ON.)

Error code:	X14
Description:	Main unit multiple feed
Causes:	Multiple paper feed occurred. 105 X14 Standard paper feed tray multiple feed A multiple feed was detected during transport of paper from the standard paper feed tray.
Remedy:	Open and close the door of the vertical transfer unit, or open and close the left front cover. (Turns the jam release cover safety SW OFF/ON.)

Error code:	X17
Description:	Paper jam in interface module
Causes:	3140 Jam before paper reached decurler IN sensor 3141 Jam before paper reached decurler OUT sensor 3164 Paper remaining at decurler IN sensor 3165 Paper remaining at decurler OUT sensor

Error code:	X18
Description:	Puncher unit error
Causes:	3142 Jam before paper reached punch OUT sensor 3143 Paper jammed at punch OUT sensor 3144 Jam before paper reached buffer path sensor 3145 Paper jammed at buffer path sensor 3166 Paper remaining at punch OUT sensor 3167 Paper remaining at buffer path sensor

Error code:	X19
Description:	Stapler unit error
Causes:	3146 Jam before paper reached compile exit sensor 3147 Paper jammed at compile exit sensor 3148 Paper jammed at compile paper sensor 3149 Jam before paper reached ejection sensor 3150 Paper jammed at ejection sensor 3168 Paper remaining at compile exit sensor 3169 Paper remaining at compile tray NO paper sensor 3170 Jam detected by ejection sensor

Error code:	X21
Description:	Paper jam affecting 3-fold tray
Causes:	3151 Jam before paper reached folder entrance sensor 3152 Paper jammed at folder entrance sensor 3153 Jam before paper reached folder exit sensor 3154 Jam before paper reached folder path sensor 2 3155 Jam before paper reached folder path sensor 3 3156 Paper jammed at folder path sensor 3 3157 Jam before paper reached folder path sensor 4 3171 Paper remaining at folder entrance sensor 3172 Paper remaining at folder exit sensor 3173 Paper remaining at folder path sensor 1 3174 Paper remaining at folder path sensor 2 3175 Paper remaining at folder path sensor 3 3176 Paper remaining at folder path sensor 4

Error code:	X22
Description:	Paper jam affecting top tray
Causes:	3158 Jam before paper reached top tray eject sensor 3159 Paper jammed at top tray eject sensor 3177 Paper remaining at top tray eject sensor

Error code:	X23
Description:	Paper jam on stacking tray
Causes:	Paper jam on Stacking tray.

Error code:	X24
Description:	Paper jam affecting booklet tray
Causes:	3160 Jam before paper reached booklet IN sensor 3161 Paper jammed at booklet IN sensor 3162 Jam before paper reached booklet folder roller exit sensor 3163 Paper jammed at booklet folder roller exit sensor 3178 Paper remaining at booklet compile NO paper sensor 3179 Paper remaining at booklet folder roller exit sensor

Error code:	X25
Description:	Paper jam affecting AF
Causes:	4410 Original removed, causing jam (the AF registration sensor was deactivated after the sheet was ejected and before scanning began; issued by the AF side) 4411 Original jammed at AF registration sensor (length error), issued by AF side Simplex scanning: After activation of the AF original IN sensor, original did not pass the AF registration sensor. Duplex scanning: After original transfer began, it did not pass the AF registration sensor. 4412 Original jammed at AF registration sensor (length error), issued by AF side After deactivation of the AF registration sensor, original did not pass the AF original IN sensor. 4413 Original jammed at AF original OUT sensor (length error), issued by AF side Simplex scanning: After deactivation of the AF registration sensor, original did not pass the AF original OUT sensor. Duplex scanning: After deactivation of the AF registration sensor, original did not pass the AF original OUT sensor. 4414 Jam before original reached AF registration sensor, issued by AF side After original was pulled in, it did not reach the AF registration sensor. 4415 Jam before original reached AF original IN sensor, issued by AF side After scanning was begun, original did not reach the AF original IN sensor. 4416 Jam before original reached AF original OUT sensor, issued by AF side Simplex scanning: After activation of the AF original IN sensor, original did not reach the AF original OUT sensor. Duplex scanning: After original transfer began, it did not reach the AF original OUT sensor.
Remedy:	Remove paper in the AF original paper path and open and close the AF feed cover. Press the Cancel or Stop button to delete the job. Press the Continue or Start button to resume reading the original.

Error code:	X26
Description:	Paper jam in tray 3
Causes:	1053 Paper being transferred did not reach vertical paper feed sensor 1 in time, based on the transfer speed.

Error code:	X27
Description:	Paper jam in FD flipper section
Causes:	1064 Paper being transferred did not reach the FD paper ejection sensor in time, based on the transfer speed.

Error code:	X28
Description:	Paper jam in FD paper ejection section
Causes:	1084 Paper being transferred did not pass the FD paper ejection sensor in time, based on the transfer speed. 11 22 Paper was still at the FD paper ejection sensor when paper transfer began.

Error code:	X29
Description:	Awaiting removal of remaining paper (emergency stop)
Causes:	24 Paper may still remain in the printer after an emergency stop.

Error code:	X30
Description:	Awaiting removal of remaining paper (power ON)
Causes:	11 25 Paper may still remain in the printer after the printer was turned ON.

Error code:	X31
Description:	Paper jam in finisher
Causes:	11 26 Paper jam in finisher

Error code:	Y01
Description:	Ink cartridge change
Causes:	No ink 327 Y01 Ink cartridge change 1 No ink has been detected during printing or maintenance operation. * Ink identification information (K, C, M, Y) is added after the error point. 328 Y01 Ink cartridge change 2 Ink sensor of the main unit reservoir fails to activate within the specified interval. * Ink identification information (K, C, M, Y) is added after the error point. 329 Y01 Ink cartridge change 3 No ink has been detected at power ON or when the tag was read after cartridge replacement. * Ink identification information (K, C, M, Y) is added after the error point.
Remedy:	Remove the applicable ink cartridge.

Error code:	Y03
Description:	Punch waste box full
Causes:	3200 1 Punch box almost full (detected by finisher) 3200 2 Punch box almost full (detected by printer)
Remedy:	Dispose of the waste from punching, or press the Close button, or delete the job.

Error code:	Y04
Description:	Staples empty
Causes:	3201 1 Stapler refilling is required (detected by finisher). 3201 2 Stapler refilling is required (detected by printer).
Remedy:	Add staples, press the Close button, or delete the job.

Error code:	Y05
Description:	Booklet staples empty
Causes:	3202 1 Booklet stapler refilling is required (front side; detected by finisher). 3202 2 Booklet stapler refilling is required (front side; detected by printer). 3203 1 Booklet stapler refilling is required (rear side; detected by finisher). 3203 2 Booklet stapler refilling is required (rear side; detected by printer).
Remedy:	Add booklet staples, press the Close button, or delete the job.

Error code:	Z01
Description:	Ink cartridge not set
Causes:	Ink cartridge(s) not set 330 Z01 Ink cartridge not set No ink cartridge detected. * Ink identification information (K, C, M, Y) is added after the error point. 336 Z01 Ink tag communication error on R/W PCB side (no tag) * Ink identification information (K, C, M, Y) is added after the error point. 337 Z01 Ink tag communication error on HC Control PCB side (no tag) * Ink identification information (K, C, M, Y) is added after the error point. 338 Z01 Ink tag communication error, other 1 (no tag) * Ink identification information (K, C, M, Y) is added after the error point.
Remedy:	Set ink cartridge(s).

Error code:	Z02
Description:	Incompatible ink color
Causes:	Ink cartridges of the incorrect color are set. 331 Z02 Incompatible ink color Wrong ink color detected. * Ink identification information (K, C, M, Y) is added after the error point.
Remedy:	Remove the ink cartridges.

Error code:	Z03
Description:	Incompatible ink cartridge
Causes:	An incorrect ink cartridge is set. 332 Z03 Incompatible ink cartridge * Ink identification information (K, C, M, Y) is added after the error point. 333 Z03 Ink tag communication error on R/W PCB side (ink check) * Ink identification information (K, C, M, Y) is added after the error point. 334 Z03 Ink tag communication error on HC Control PCB side (ink check) * Ink identification information (K, C, M, Y) is added after the error point. 335 Z03 Ink tag communication error, other 1 (ink check) * Ink identification information (K, C, M, Y) is added after the error point.
Remedy:	Remove the ink cartridges.

Error code:	Z04
Description:	Ink cover not set
Causes:	The ink bottle cover is open. 325 Z04 Ink bottle cover not set The ink bottle cover is detected as not set.
Remedy:	Close the ink bottle cover.

Error code:	Z05
Description:	Front cover not set (left/right)
Causes:	The front cover (left/right) is open. 237 Z05 Left front cover not set The left front cover is detected as not set. 238 Z05 Right front cover not set The right front cover is detected as not set.
Remedy:	Close the front cover (left/right).

Error code:	Z06
Description:	Transfer cover (left) not set
Causes:	The transfer cover (left) is open. 230 Z06 Switchback unit not set The switchback unit is not set.
Remedy:	Close the transfer cover (left).

Error code:	Z08
Description:	Vertical transfer unit door not set
Causes:	The left door of the MTPF is open. 411 Z08 Vertical transfer unit door not set The door of the FL vertical transfer unit is open.
Remedy:	Close the left door of the MTPF.

Error code:	Z09
Description:	Feed tray 1 not set
Causes:	Feed tray 1 is open. 435 Z09 Feed tray 1 is open. The feed tray 1 set SW is OFF (detection of feed tray open).
Remedy:	Close the applicable feed tray. This error is ignored while paper fed from the standard paper feed tray is being printed. or during head maintenance.

Error code:	Z10
Description:	Feed tray 2 not set
Causes:	Feed tray 2 is open. 436 Z10 Feed tray 2 is open. The feed tray 2 set SW is OFF (detection of feed tray open).
Remedy:	Close the applicable feed tray. This error is ignored while paper fed from the standard paper feed tray is being printed. or during head maintenance.

Error code:	Z11
Description:	Standard paper feed tray check
Causes:	The safety SW for the standard paper feed tray is pressed. Or both the Upper and Lower Limit Sensors are activated (too much paper on the tray). 111 Z11 Standard paper feed tray elevator upper limit SW detection The upper limit SW for the standard paper feed tray is turned ON. 112 Z11 Standard paper feed tray overfilled The upper limit sensor and lower limit sensor are turned ON simultaneously for more than 1 second at power ON or during a standard paper feed tray moving operation. 120 Z11 Standard paper feed tray elevator lower limit SW detection The lower limit SW for the standard paper feed tray is turned ON.
Remedy:	Deactivate the safety SW for the standard paper feed tray. Remove the overloaded paper from the standard paper feed tray to release the Upper/Lower-Limit Sensor.

Error code:	Z15
Description:	HC vertical paper feed unit cover open
Causes:	3120 The printer has detected that the finisher interface unit cover is open.
Remedy:	Activate the switch of the finisher interface unit cover.

Error code:	Z16
Description:	Left finisher cover open
Causes:	Deactivate the interface module front door switch.
Remedy:	3121 The printer has detected that the interface unit cover is open.

Error code:	Z17
Description:	Booklet unit not connected
Causes:	3122 Booklet drawer open
Remedy:	Set the booklet drawer in place.

Error code:	Z18
Description:	Right finisher cover open
Causes:	3123 Finisher front cover open
Remedy:	Deactivate the finisher front door switch.

Error code:	Z20
Description:	3-fold tray not loaded
Causes:	3124 The 3-fold tray is not loaded (it is pulled out).
Remedy:	Load the 3-fold tray.

Error code:	Z21
Description:	Base cover open
Causes:	1095 Internal feed paper jam release door open
Remedy:	Close the jam release door on the base.

Error code:	Z22
Description:	Front cover open (BP lower limit)
Causes:	1255 The front left cover is open when the belt platen is at the lower limit position. 1256 The front right cover is open when the belt platen is at the lower limit position.
Remedy:	Close the front cover (left or right).

Error code:	Z23
Description:	Switchback cover open (BP lower limit)
Causes:	1257 The switchback cover is open when the belt platen is at the lower limit position.
Remedy:	Close the switchback cover.

Error code:	Z24
Description:	Check paper feed tray (BP lower limit)
Causes:	1253 The upper or lower paper feed tray interlock switch is deactivated when the belt platen is in the lower limit position.
Remedy:	Release interlock.

Error code:	Z25
Description:	Tray 1 not loaded (BP lower limit)
Causes:	1250 Internal paper feed tray 1 is open when the belt platen is in the lower limit position.
Remedy:	Close internal paper feed tray 1.

Error code:	Z26
Description:	Tray 2 not loaded (BP lower limit)
Causes:	1251 Internal paper feed tray 2 is open when the belt platen is in the lower limit position.
Remedy:	Close internal paper feed tray 2.

Error code:	Z27
Description:	Tray 3 not loaded (BP lower limit)
Causes:	1252 Internal paper feed tray 3 is open when the belt platen is in the lower limit position.
Remedy:	Close internal paper feed tray 3.

Error code:	Z28
Description:	Base cover open (BP lower limit)
Causes:	1254 The internal paper feed jam release door is open when the belt platen is in the lower limit position.
Remedy:	Close the jam release door on the base.

Деталь:	SWITCHBACK UNIT B(1-19)
Парткод:	050-74018-086

Деталь:	* SWITCHBACK GUIDE
Парткод:	050-64306-086

Деталь:	* PULLEY
Парткод:	611-90028-002

Деталь:	* METAL
Парткод:	607-15016-004

Деталь:	* UPPER TRANSFER DRIVE ROLLER 6
Парткод:	050-64107-080

Деталь:	* RELEASE LEVER SEAL
Парткод:	050-64364-083

Деталь:	* RELEASE LEVER SPRING
Парткод:	050-64319-088

Деталь:	Socket Stopper Plate R
Парткод:	050-64371-004

Деталь:	Socket Stopper Plate F
Парткод:	050-64370-008

Деталь:	PAPER POSITION DET. ASSY(1-13)
Парткод:	050-74008-080

Деталь:	PAPER POSITION DET. ASSY A4 (1-13)
Парткод:	050-75043-009

Деталь:	FD PAPER EJECTION UNIT(1-41)
Парткод:	050-74020-080

Деталь:	* FULCRUM BASE PLATE R
Парткод:	050-62174-082

Деталь:	* DE-ELECTRICITY BRUSH
Парткод:	050-62060-087

Деталь:	* FULCRUM BASE PLATE F
Парткод:	050-62173-086

Деталь:	* HOOK CATCH
Парткод:	050-64362-080

Деталь:	* SENSOR BRACKET
Парткод:	050-64323-085

Деталь:	* SENSOR
Парткод:	444-33013-007

Деталь:	* HINGE
Парткод:	050-64361-084

Деталь:	* SWITCHBACK GUIDE U
Парткод:	050-62027-080

Деталь:	* SWITCHBACK GUIDE L
Парткод:	050-62028-086

Деталь:	* EJECTION DRIVEN ROLLER 2
Парткод:	050-62068-088

Деталь:	* JAM RELEASE SHAFT
Парткод:	050-62179-084

Деталь:	* SHAFT SOCKET PLATE
Парткод:	050-55216-080

Деталь:	CA_HOLDER_UNIT_SET(Fig24,25)
Парткод:	050-79630-006

Деталь:	*CA_MCTOR_ASSY(9-11)
Парткод:	050-79636-004

Деталь:	**Motor Assy(CWRS-445PA)
Парткод:	023-74001-003

Деталь:	Controller PCB Unit
Парткод:	050-74035-088

Деталь:	SWITCHBACK UNIT A(1-42)
Парткод:	050-74017-080

Riso ComColor 3050

Общие характеристики

Макс. формат

Размещение

Тип

Технология печати

Тип устройства

Цветность печати

Факс

Сканер

Копир

Печать фотографий

Телефон

Принтер

Пигментные чернила

Двусторонняя печать

Печать без полей

Макс, разрешение для ч/б печати

Скорость ч/б печати

Сканер

Стандарт TWAIN

Стандарт WIA

Слайд-адаптер

Отправка изображения по e-mail

Расходные материалы

Печать на:

Плотность бумаги

Факс

Цветной

Телефон

Caller ID

Автоответчик

Стандарт DECT

Спикерфон

Проводная трубка

АОН

Беспроводная трубка

Языки управления

Лотки

Подача бумаги

Вывод бумаги

Финишер

Брошюровщик

Степлер

Сортер

Интерфейсы

Инфракрасный порт

Wi-Fi

LPT

Bluetooth

FireWire (IEEE 1394)

Устройство для чтения карт памяти

RS-232

Ethernet (RJ-45)

Память/Процессор

Объем памяти

Процессор

Частота процессора

Емкость жесткого диска

Дополнительная информация

Экран

Диагональ дисплея

Работа от аккумулятора

Поддержка ОС

Уровень шума

Габариты

Высота

Глубина

Ширина

Вес

Модули

Детали KG Roller Area

Коды ошибок

Описание

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку

Деталь:	* Switch Back Cover Assy (30-39)
Парткод:	050-75001-004

Деталь:	* RE-FEED DRIVE ROLLER
Парткод:	050-64106-181

Деталь:	* JAM RELEASE DIAL SEAL
Парткод:	050-64363-087

Деталь:	* SWITCHBACK DRIVEN ROLLER
Парткод:	050-64105-088

Деталь:	** JAM RELEASE HOOK
Парткод:	050-64342-187

Деталь:	** RELEASE LEVER SPRING
Парткод:	050-64329-083

Деталь:	** RELEASE LEVER SHAFT
Парткод:	050-64341-083

Деталь:	** JAM RELEASE LEVER
Парткод:	050-64343-086

Деталь:	** RELEASE LEVER SEAL
Парткод:	050-64365-080

Деталь:	PAPER ELEVATION UNIT(1-31)
Парткод:	050-74016-083