Ricoh SPC410DN
Рейтинг
Модули
Frame And Electrical Section 2
Drive Section 1
Optics Section
Paper Transfer Section 2
TONER SUPPLY SECTION
Paper Transfer Section 3
PCU SECTION
DRIVE SECTION 3
Paper Transfer Section 1
DRIVE SECTION 2
Supply Unit
PAPER TRAY
Frame And Electrical Section 1
BY-PASS FEED SECTION
Paper Regist Section
PAPER EXIT SECTION
EXTERIOR
FUSING SECTION
Frame And Electrical Section 3
FUSING UNIT
Детали PCU SECTION
| Деталь: | Power Supply Cord:Stopper:NA:Assy |
| Парткод: | G102 5501 |
| Деталь: | Power Supply Cord:EU |
| Парткод: | G102 5502 |
| Деталь: | Shadeing Plate:Upper |
| Парткод: | G102 5821 |
| Деталь: | Power Pack:CT:G-P2 |
| Парткод: | GZ32 0012 |
| Деталь: | Insulating Sheet:Power Pack:1 |
| Парткод: | G102 5802 |
| Деталь: | Power Supply Unit:DOM/NA |
| Парткод: | GZ23 0028 |
| Деталь: | Power Supply Unit:EU/AA |
| Парткод: | GZ23 0029 |
| Деталь: | Harness:Power Supply Unit |
| Парткод: | G102 5435 |
| Деталь: | Harness:Power Supply Unit:Heater (NA) |
| Парткод: | G102 5413 |
| Деталь: | Harness:Power Supply Unit:Heater (EU) |
| Парткод: | G102 5414 |
| Деталь: | Bracket:Power Supply Unit |
| Парткод: | G102 5800 |
| Деталь: | Bracket:Power Supply Cord:Stopper:1 |
| Парткод: | G102 5843 |
| Деталь: | Inlet:EU:Assy |
| Парткод: | G102 5515 |
| Деталь: | Harness:Inlet:EU |
| Парткод: | G102 5516 |
| Деталь: | Ground Plate:Finishing Sub-unit |
| Парткод: | G102 1058 |
| Деталь: | Magnetic Clutch:Registration:Assy |
| Парткод: | GX20 0014 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Ground Plate:Drive Unit |
| Парткод: | G102 1264 |
| Деталь: | Ground Plate:Transfer:No.2:Right |
| Парткод: | G102 1327 |
| Деталь: | Ground Plate:Drive Unit |
| Парткод: | G102 1265 |
| Деталь: | Ground Plate:Registration Roller:Right |
| Парткод: | G102 1266 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2075 |
| Деталь: | Ground Plate:Transfer:Second |
| Парткод: | G102 1129 |
| Деталь: | Spring Plate:Paper Tray:Fix:Assy |
| Парткод: | G102 2855 |
| Деталь: | Timing Belt:S3M:318 |
| Парткод: | GA04 3024 |
| Деталь: | Gear:24Z |
| Парткод: | GB01 3052 |
| Деталь: | Timing Pulley:Drive:Fusing |
| Парткод: | GB03 0000 |
| Деталь: | Gear:24/36z |
| Парткод: | GB01 7035 |
| Деталь: | Gear:27/36z |
| Парткод: | GB01 7036 |
| Деталь: | Bracket:Drive:Fusing:Assy |
| Парткод: | G102 1316 |
| Деталь: | Bracket:stopper:CL:Assy |
| Парткод: | G159 1290 |
| Деталь: | Holder:Magnetic Clutch:Paper Feed |
| Парткод: | G102 2829 |
| Деталь: | Bracket:Drive:Paper Feed:Assy |
| Парткод: | G102 1301 |
| Деталь: | Gear:20/45z |
| Парткод: | GB01 7032 |
| Деталь: | Bracket:Stopper:Right |
| Парткод: | G102 4706 |
| Деталь: | Bushing:Registration:Right |
| Парткод: | GA08 0027 |
| Деталь: | Gear:26/62z |
| Парткод: | GB01 7033 |
| Деталь: | Gear:24/45z |
| Парткод: | GB01 7034 |
| Деталь: | Gear:33Z |
| Парткод: | GB01 3051 |
| Деталь: | Registration Roller:Drive |
| Парткод: | GF02 0033 |
| Деталь: | Roller:Middle |
| Парткод: | GF02 0034 |
| Деталь: | Gear:14z |
| Парткод: | GB01 1049 |
| Деталь: | Bracket:Drive:Discharge Waste Toner |
| Парткод: | G102 1325 |
| Деталь: | Ground Plate:Transfer:No.2:Left |
| Парткод: | G102 1329 |
| Деталь: | Bushing:Registration:Left |
| Парткод: | GA08 0026 |
| Деталь: | Gear:38z |
| Парткод: | GB01 1061 |
| Деталь: | Magnetic Clutch:0.25nm |
| Парткод: | GX20 0021 |
| Деталь: | Seal:Main:Right Front |
| Парткод: | G159 1274 |
| Деталь: | Ground Plate:Fusing |
| Парткод: | G102 1174 |
| Деталь: | Ground Wire:Fusing:Right |
| Парткод: | G102 1175 |
| Деталь: | Cover:Polygon Scanner:Assy |
| Парткод: | G102 1940 |
| Деталь: | Shielding Plate:Polygon Scanner:Separation |
| Парткод: | G159 1943 |
| Деталь: | Seal:PCB:Polygon Scanner |
| Парткод: | G102 1945 |
| Деталь: | PCB:Polygon Scanner |
| Парткод: | G159 5291 |
| Деталь: | Polygon Scanner:Type-R |
| Парткод: | GX06 0021 |
| Деталь: | Shield:Polygon Scanner |
| Парткод: | G102 1944 |
| Деталь: | Harness:Polygon Mirror Motor |
| Парткод: | G102 5450 |
| Деталь: | PCB:Sync Detector Board:1PD |
| Парткод: | G102 5060 |
| Деталь: | Laser Diode Unit:Assy |
| Парткод: | G102 1960 |
| Деталь: | Lever:Fix:Imaging Unit |
| Парткод: | G102 1997 |
| Деталь: | Spring Plate:Imaging Unit |
| Парткод: | G102 1998 |
| Деталь: | Spring Plate:Laser Diode Unit |
| Парткод: | G102 1963 |
| Деталь: | Decal - LD 655 |
| Парткод: | AA00 0217 |
| Деталь: | Cover:Optical Housing:Assy |
| Парткод: | G102 1990 |
| Деталь: | Harness:Sync Detector |
| Парткод: | G102 5451 |
| Деталь: | Cover:Fusing:Entrance Sensor |
| Парткод: | G102 4661 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0118 |
| Деталь: | Guide Plate:Transfer Roller:Upper |
| Парткод: | G102 4656 |
| Деталь: | Holder:Registration:Driven:Right |
| Парткод: | G102 4622 |
| Деталь: | Bushing:Registration:Driven |
| Парткод: | GA08 0025 |
| Деталь: | Compression Spring:20n |
| Парткод: | GA06 3062 |
| Деталь: | Registration Roller:Driven |
| Парткод: | GF02 1005 |
| Деталь: | Holder:Registration:Driven:Left |
| Парткод: | G102 4623 |
| Деталь: | Lever:Cover:Inner:Left |
| Парткод: | G102 4655 |
| Деталь: | Lever:Lock:Cover:Left |
| Парткод: | G102 4652 |
| Деталь: | Shaft:Lever:Inner:Assy |
| Парткод: | G102 4651 |
| Деталь: | Torsion Spring:Lever:Duplex:Right |
| Парткод: | GA06 6046 |
| Деталь: | Lever:Lock:Cover:Right |
| Парткод: | G102 4653 |
| Деталь: | Cover:Duplex:Entrance |
| Парткод: | G102 4662 |
| Деталь: | Original Sensor |
| Парткод: | AW50 0026 |
| Деталь: | Decal:Operate:Fusing |
| Парткод: | GA00 3132 |
| Деталь: | Lever:Cover:Inner:Right |
| Парткод: | G102 4654 |
| Деталь: | Cover:Front:Inner |
| Парткод: | G102 4650 |
| Деталь: | Roller:Driven:Duplex |
| Парткод: | GF02 2025 |
| Деталь: | Torsion Spring:Driven:Duplex |
| Парткод: | GA06 6044 |
| Деталь: | Harness:Duplex:Connecting |
| Парткод: | G102 5498 |
| Деталь: | Cover:Duplex:Middle |
| Парткод: | G102 4663 |
| Деталь: | Bracket:Cover:Stopper:Inner:Peen |
| Парткод: | G102 4657 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Sheet:Surface Of Paper Sensor |
| Парткод: | G102 4664 |
| Деталь: | Guide Plate:Registration:Driven |
| Парткод: | G102 2581 |
| Деталь: | Lever:Pressure:Transfer Unit |
| Парткод: | G102 6292 |
| Деталь: | Spring:Transfer Unit:Left |
| Парткод: | G102 6293 |
| Деталь: | Torsion Spring:Lever:Duplex:Left |
| Парткод: | GA06 6045 |
| Деталь: | Shielding Plate:Power Supply Unit |
| Парткод: | G102 1061 |
| Деталь: | Rail:Cleaning Unit:Peen |
| Парткод: | G102 3868 |
| Деталь: | Plate:Toner Bottle |
| Парткод: | G102 1072 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | B039 2558 |
| Деталь: | Base:Toner Bottle:Sub-assy |
| Парткод: | G102 1070 |
| Деталь: | Ground Plate:Push Switch:Exit |
| Парткод: | G102 1393 |
| Деталь: | SWITCH:CS1A-B2CA |
| Парткод: | 12 042 736 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Gear:28Z |
| Парткод: | GB01 3060 |
| Деталь: | Cover:Toner Supply:Lower |
| Парткод: | G102 1125 |
| Деталь: | Holder:Ground Plate:Connector |
| Парткод: | G102 1166 |
| Деталь: | Ground Plate:Paper Tray:Rear Lower |
| Парткод: | G102 2845 |
| Деталь: | Push Switch:Paper Size Sensor |
| Парткод: | GW50 0002 |
| Деталь: | Ground Plate:Base:Lower |
| Парткод: | G102 1052 |
| Деталь: | Rail:Paper Tray:Left |
| Парткод: | G102 1053 |
| Деталь: | Rail:Paper Tray:Right |
| Парткод: | G102 1054 |
| Деталь: | Holder:Rubber Foot |
| Парткод: | G102 1041 |
| Деталь: | Stand:Frame |
| Парткод: | G102 1040 |
| Деталь: | Decal:Base:Toner Bottle:Y |
| Парткод: | GA00 1063 |
| Деталь: | Decal:Base:Toner Bottle:C |
| Парткод: | GA00 1062 |
| Деталь: | Decal:Base:Toner Bottle:M |
| Парткод: | GA00 1061 |
| Деталь: | Decal:Base:Toner Bottle:K |
| Парткод: | GA00 1060 |
| Деталь: | Ground Plate:Connector:Y |
| Парткод: | G102 1147 |
| Деталь: | Ground Plate:Connector:K |
| Парткод: | G102 1146 |
| Деталь: | Ground Wire:ID:Connecting |
| Парткод: | G102 1148 |
| Деталь: | Ground Wire:ID:Gnd |
| Парткод: | G102 1159 |
| Деталь: | Shaft:Drive:Agitator |
| Парткод: | GA14 8011 |
| Деталь: | RUBBER FOOT:FRAME |
| Парткод: | G102 1042 |
| Деталь: | Base:Frame:Lower |
| Парткод: | G102 1051 |
| Деталь: | Harness:ID chip Connector |
| Парткод: | G102 1120 |
| Деталь: | Sheet:Base:Right |
| Парткод: | G102 2848 |
| Деталь: | Sheet:Base:Left |
| Парткод: | G102 2849 |
| Деталь: | Harness:Exit:Cover:Sensor |
| Парткод: | G102 5477 |
| Деталь: | Cap:Base:Toner Supply |
| Парткод: | G102 3331 |
| Деталь: | Insulating Sheet:Paper Size Sensor |
| Парткод: | G102 1182 |
| Деталь: | Bracket:Spring Plate:Assy |
| Парткод: | G102 1141 |
| Деталь: | Decal:Operate:Fusing |
| Парткод: | GA00 3132 |
| Деталь: | Inner Cover:Right Front |
| Парткод: | G102 1511 |
| Деталь: | Cap:Inner Cover:Right Front |
| Парткод: | G102 1381 |
| Деталь: | Cover:Bracket:Stay |
| Парткод: | G102 4708 |
| Деталь: | Stay:Stopper:Right |
| Парткод: | G102 4707 |
| Деталь: | Stopper:Cover:Outer:Peen |
| Парткод: | G102 4702 |
| Деталь: | Spring:Stopper:Right |
| Парткод: | GA06 3050 |
| Деталь: | Bracket:Stopper:Outer |
| Парткод: | G102 4700 |
| Деталь: | Guide Plate:Connecting:Assy |
| Парткод: | G102 2600 |
| Деталь: | Cover:Registration Sensor |
| Парткод: | G102 2708 |
| Деталь: | Lever:Pressure:Connecting |
| Парткод: | G102 2609 |
| Деталь: | Compression Spring:8n |
| Парткод: | GA06 3053 |
| Деталь: | BUSHING - M4 |
| Парткод: | G060 2652 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3607 |
| Деталь: | Guide Plate:Registration |
| Парткод: | G102 2550 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Feeler:Registration Sensor |
| Парткод: | G102 2571 |
| Деталь: | Case:Remove Paper Dust |
| Парткод: | G102 2561 |
| Деталь: | Bracket:Stopper:Inner |
| Парткод: | G102 4701 |
| Деталь: | Stopper:Cover:Inner:Peen |
| Парткод: | G102 4704 |
| Деталь: | Spring Plate:Pressure:Imaging Unit |
| Парткод: | G102 1059 |
| Деталь: | Ground Plate:Discharge |
| Парткод: | G102 1144 |
| Деталь: | Roller:Driven:3xmm16 |
| Парткод: | AF02 2160 |
| Деталь: | Spring:Stopper:Left |
| Парткод: | GA06 3068 |
| Деталь: | Bracket:Push Switch:Cover:Outer |
| Парткод: | G102 4712 |
| Деталь: | Harness:Front:Cover:Sensor |
| Парткод: | G102 5535 |
| Деталь: | SWITCH:CS1A-B2CA |
| Парткод: | 12 042 736 |
| Деталь: | Ground Plate:Stay:Stopper |
| Парткод: | G102 4710 |
| Деталь: | Bracket:Spring:Stopper |
| Парткод: | G102 4711 |
| Деталь: | Decal:Release:Lever:Drum Stay |
| Парткод: | GA00 1011 |
| Деталь: | Ground Plate:Drum Positioning |
| Парткод: | G102 1080 |
| Деталь: | Band:Stopper:Door |
| Парткод: | G102 1355 |
| Деталь: | Snap Rings:4:1.7t |
| Парткод: | GA10 0002 |
| Деталь: | Bracket:Left:Assy |
| Парткод: | G102 1113 |
| Деталь: | Decal:Slide Rail:K |
| Парткод: | GA00 3191 |
| Деталь: | Decal:Slide Rail:M |
| Парткод: | GA00 3192 |
| Деталь: | Decal:Slide Rail:C |
| Парткод: | GA00 3193 |
| Деталь: | Decal:Slide Rail:Y |
| Парткод: | GA00 3194 |
| Деталь: | Decal:Drum Stay:Lock |
| Парткод: | GA00 3114 |
| Деталь: | Decal:Operate:Lock:Drum Stay |
| Парткод: | GA00 3127 |
| Деталь: | Decal:Toner Recycling Section |
| Парткод: | GA00 3130 |
| Деталь: | Decal:Positioning Display (G160) |
| Парткод: | GA00 3149 |
| Деталь: | Decal:Positioning Display (G161) |
| Парткод: | G159 1173 |
| Деталь: | Slide Rail:Y:P2:Assy |
| Парткод: | G159 1066 |
| Деталь: | Slide Rail:C:P2:Assy |
| Парткод: | G159 1067 |
| Деталь: | Decal:Development Unit:Y |
| Парткод: | GA00 3110 |
| Деталь: | Decal:Operate:PCU |
| Парткод: | GA00 3131 |
| Деталь: | Slide Rail:M:P2:Assy |
| Парткод: | G159 1068 |
| Деталь: | Slide Rail:K:P2 |
| Парткод: | G159 1048 |
| Деталь: | Bracket:Hinge:Left Middle |
| Парткод: | GG06 1009 |
| Деталь: | Guide:Harness:Main Switch |
| Парткод: | G102 5828 |
| Деталь: | Bracket:Hinge:Left |
| Парткод: | GG06 1008 |
| Деталь: | Shaft:Hinge:Drum Stay |
| Парткод: | GA14 8010 |
| Деталь: | PCU Rail:Spacer |
| Парткод: | G102 1035 |
| Деталь: | Cover:Plate:Right |
| Парткод: | G102 1117 |
| Деталь: | Bracket:Right:Assy |
| Парткод: | G102 1116 |
| Деталь: | Bracket:Waste Toner Sensor |
| Парткод: | G102 6595 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Decal:Development Uni:M |
| Парткод: | GA00 3109 |
| Деталь: | Decal:Development Unit:C |
| Парткод: | GA00 3108 |
| Деталь: | Decal:Development Unit:K |
| Парткод: | GA00 3111 |
| Деталь: | Drum Positioning Plate |
| Парткод: | G159 1076 |
| Деталь: | Cover:Plate:Left |
| Парткод: | G102 1114 |
| Деталь: | Decal:Drum Stay:Un Lock:Left |
| Парткод: | GA00 3115 |
| Деталь: | Spring Plate - Band Stopper |
| Парткод: | A232 3962 |
| Деталь: | Cover:Connector:Drum Stay |
| Парткод: | G102 1168 |
| Деталь: | Rivet:12A1 |
| Парткод: | G102 1169 |
| Деталь: | Snap Rings:4:2.2t |
| Парткод: | GA10 0003 |
| Деталь: | Bracket:Belt:Drum Positioning |
| Парткод: | G102 1173 |
| Деталь: | Sheet:Slide Rail |
| Парткод: | GA15 1038 |
| Деталь: | Fan:MM60:NMB:N |
| Парткод: | GX64 0021 |
| Деталь: | Duct:Fan:Fusing |
| Парткод: | G102 1060 |
| Деталь: | Bracket:Fan |
| Парткод: | G102 5831 |
| Деталь: | Fan Motor MM60x15 |
| Парткод: | GX64 0027 |
| Деталь: | Brushless Motor:Photoconductor |
| Парткод: | GX06 0017 |
| Деталь: | Brushless Motor:Development:Color |
| Парткод: | GX06 0018 |
| Деталь: | Bracket:Motor:Development:Color |
| Парткод: | G102 1280 |
| Деталь: | Bracket:DC Motor |
| Парткод: | G102 3311 |
| Деталь: | Gear:26/54z |
| Парткод: | GB01 7050 |
| Деталь: | Collar:Toner Supply |
| Парткод: | GA13 2005 |
| Деталь: | DC Motor:Line:Toner Supply:Assy |
| Парткод: | G159 3312 |
| Деталь: | Bracket:DC Motor:Y |
| Парткод: | G102 3321 |
| Деталь: | Fan Motor - DC24V |
| Парткод: | GX64 0020 |
| Деталь: | Gear:34/64z |
| Парткод: | GB01 7043 |
| Деталь: | Ground Plate:IOB |
| Парткод: | G102 1043 |
| Деталь: | Guide Plate:Duplex:Upper |
| Парткод: | G102 4619 |
| Деталь: | Lever:Cover:Outer |
| Парткод: | G102 4603 |
| Деталь: | Stepper Motor:PM42L048RBG8 |
| Парткод: | GX06 0019 |
| Деталь: | Bracket:Stepper Motor:Reverse |
| Парткод: | G102 4610 |
| Деталь: | Side Plate:Drive:Duplex:Right |
| Парткод: | G102 4602 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Gear:27z |
| Парткод: | GB01 0018 |
| Деталь: | Gear:32/32z |
| Парткод: | GB01 7047 |
| Деталь: | Duct:Reverse |
| Парткод: | G102 4624 |
| Деталь: | Timing Belt:60S2M296 |
| Парткод: | GA04 3027 |
| Деталь: | Gear:20z:21t |
| Парткод: | GB01 7045 |
| Деталь: | Gear:27/52z |
| Парткод: | GB01 7046 |
| Деталь: | Gear:20Z |
| Парткод: | GB01 1057 |
| Деталь: | Timing Belt:60S2M234 |
| Парткод: | GA04 3026 |
| Деталь: | Gear:52z/21t |
| Парткод: | GB01 7044 |
| Деталь: | Gear:36z |
| Парткод: | GB01 0017 |
| Деталь: | Gear:52z |
| Парткод: | GB01 0019 |
| Деталь: | Plate - Logo RIC |
| Парткод: | G139 2690 |
| Деталь: | Plate:Logo:GES |
| Парткод: | GA00 1052 |
| Деталь: | Plate:Logo:NSA |
| Парткод: | GA00 1053 |
| Деталь: | Plate:Logo:REX |
| Парткод: | GA00 1054 |
| Деталь: | Plate:Logo:INF |
| Парткод: | GA00 1055 |
| Деталь: | Cover:Front:Outer |
| Парткод: | G102 4600 |
| Деталь: | Drum Positioning Plate :Drive:Duplex |
| Парткод: | G102 4604 |
| Деталь: | Latch - By Pass Feed Table |
| Парткод: | AG07 1007 |
| Деталь: | Discharge Brush:Reverse Roller |
| Парткод: | G159 4627 |
| Деталь: | Bracket:Reverse:Sensor |
| Парткод: | G102 4621 |
| Деталь: | PHOTO REFIECTION SENSOR:EXIT |
| Парткод: | GW01 0007 |
| Деталь: | Ground Wire:Duplex:Outer |
| Парткод: | G102 4620 |
| Деталь: | Ground Plate:Reverse Roller |
| Парткод: | G102 4626 |
| Деталь: | Bracket:Cover:Stopper:Outer:Peen |
| Парткод: | G102 4611 |
| Деталь: | Harness:Duplex:Motor:Connecting |
| Парткод: | G102 5458 |
| Деталь: | Bracket:Stepper Motor:Duplex |
| Парткод: | G102 4625 |
| Деталь: | Ground Plate:Transport Roller:Lower |
| Парткод: | G102 4616 |
| Деталь: | Transport Roller:Duplex |
| Парткод: | GF02 0036 |
| Деталь: | Inner Cover:Drive:Duplex |
| Парткод: | G102 4608 |
| Деталь: | Harness:Duplex:OPU:Connecting |
| Парткод: | G159 5463 |
| Деталь: | OPERATION PANEL |
| Парткод: | G161 1401 |
| Деталь: | Ground Plate:Transport Roller:Lower |
| Парткод: | G102 4606 |
| Деталь: | Side Plate:Drive:Duplex:Left |
| Парткод: | G102 4601 |
| Деталь: | Ground Plate:Transport Roller |
| Парткод: | G102 4605 |
| Деталь: | Compression Spring:Lever:5n |
| Парткод: | GA06 0078 |
| Деталь: | Fan:Mm40x15:Nidec:L |
| Парткод: | GX64 0029 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Ground Wire:Duplex |
| Парткод: | G102 4618 |
| Деталь: | Ground Wire - OPU |
| Парткод: | G102 5539 |
| Деталь: | Cover:Outer:Harness |
| Парткод: | G102 4613 |
| Деталь: | Decal:Name Plate:RIC:C410ED:EXP |
| Парткод: | G160 1210 |
| Деталь: | Decal:Name Plate:GES:C410DN:EU |
| Парткод: | G160 1214 |
| Деталь: | Decal:Name Plate:NSA:C410DN:EU |
| Парткод: | G160 1215 |
| Деталь: | Decal:Name Plate:REX:C410DN:EU |
| Парткод: | G160 1216 |
| Деталь: | Decal:Name Plate:INF:IPC2525DN:EU |
| Парткод: | G160 1218 |
| Деталь: | Decal:Name Plate:RIC:C411DN:EXP |
| Парткод: | G161 1211 |
| Деталь: | Decal:Name Plate:GES:C411DN:EU |
| Парткод: | G161 1215 |
| Деталь: | Decal:Name Plate:NSA:C411DN:EU |
| Парткод: | G161 1216 |
| Деталь: | Decal:Name Plate:REX:C411DN:EU |
| Парткод: | G161 1217 |
| Деталь: | Decal:Name Plate:INF:IPC3030DN:EU |
| Парткод: | G161 1219 |
| Деталь: | Toner Supply Sub-unit |
| Парткод: | G159 3320 |
| Деталь: | Harness:Intermediate Transfer |
| Парткод: | G102 5478 |
| Деталь: | Harness:Density Sensor:Connecting |
| Парткод: | G159 5529 |
| Деталь: | Holder:Positioning Sensor |
| Парткод: | G102 1263 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Screw:M3 |
| Парткод: | AA14 3544 |
| Деталь: | Supporter:Harness:Frame |
| Парткод: | G102 5840 |
| Деталь: | Brushless Motor:Drive:Paper Feed |
| Парткод: | GX06 0015 |
| Деталь: | Drive Unit:Assy |
| Парткод: | G102 1224 |
| Деталь: | Ground Plate:Drive:Fusing |
| Парткод: | G102 1328 |
| Деталь: | Transfer Belt Contact Motor Assy |
| Парткод: | G102 1350 |
| Деталь: | Gear:Development:Idler:No.1 |
| Парткод: | GB01 1082 |
| Деталь: | Magnetic Spring Clutch |
| Парткод: | GX20 0012 |
| Деталь: | Bracket:Magnetic Spring Clutch |
| Парткод: | G102 1258 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Brushless Motor:Photoconductor:Colo |
| Парткод: | GX06 0016 |
| Деталь: | Stepper Motor:drive:Fransfer:Assy |
| Парткод: | G159 1345 |
| Деталь: | Shaft:Development |
| Парткод: | GA14 5008 |
| Деталь: | PCU:Gaia-P1K:M:ASSY |
| Парткод: | G235 2034 |
| Деталь: | PCU:Gaia-P1K:C:ASSY |
| Парткод: | G235 2035 |
| Деталь: | PCU:Gaia-P1K:Y:ASSY |
| Парткод: | G235 2036 |
| Деталь: | Fusing Unit:Gaia-P2A:NA:Sub-Assy |
| Парткод: | G158 4051 |
| Деталь: | Fusing Unit:Gaia-P2A:EU:Sub-Assy |
| Парткод: | G158 4052 |
| Деталь: | Fusing Unit:Gaia-P2B:NA:Sub-Assy |
| Парткод: | G159 4051 |
| Деталь: | Fusing Unit:Gaia-P2B:EU:Sub-Assy |
| Парткод: | G159 4052 |
| Деталь: | Transfer Unit:Assy |
| Парткод: | G159 6200 |
| Деталь: | Manual:Operating Instructions:Safety:G-P2:NA |
| Парткод: | G160 8601 |
| Деталь: | Manual:Quick_instoll:G-p2:NA |
| Парткод: | G160 8605 |
| Деталь: | Sheet:Color_Chart:G-P2 |
| Парткод: | G160 7491 |
| Деталь: | Paper Tray:Assy |
| Парткод: | G159 2527 |
| Деталь: | Arm:Pressure:Change |
| Парткод: | G102 2807 |
| Деталь: | SPRING TENSION |
| Парткод: | G096 3083 |
| Деталь: | Cam:Pressure:Paper Tray |
| Парткод: | G102 2804 |
| Деталь: | Feeler:Pressure:Paper Tray |
| Парткод: | G102 2808 |
| Деталь: | Shaft:Pressure:Paper Tray |
| Парткод: | G102 2803 |
| Деталь: | LEFT SIDE FENCE |
| Парткод: | G096 3055 |
| Деталь: | Seal:Side Fence:Rear |
| Парткод: | G102 2863 |
| Деталь: | Seal:Side Fence |
| Парткод: | G102 2862 |
| Деталь: | Gear - 16Z |
| Парткод: | A267 2869 |
| Деталь: | Side Fence:Right:Assy |
| Парткод: | G159 2553 |
| Деталь: | Tray Bottom Plate:Adhesion |
| Парткод: | G102 2818 |
| Деталь: | Lever:Pressure:Change |
| Парткод: | G102 2805 |
| Деталь: | Compression Spring:Tray Bottom Plate |
| Парткод: | G102 2817 |
| Деталь: | Holder:Compression Spring |
| Парткод: | G102 2816 |
| Деталь: | Filler Paper Volume Sensor |
| Парткод: | G102 2809 |
| Деталь: | Friction Pad Adhesion |
| Парткод: | G096 3066 |
| Деталь: | Protection:Paper Tray:Left |
| Парткод: | G102 2813 |
| Деталь: | Separation Compression Spring |
| Парткод: | G096 3084 |
| Деталь: | End Fence Pressure |
| Парткод: | G096 3088 |
| Деталь: | Sheet:Holder:Paper Tray |
| Парткод: | G102 2833 |
| Деталь: | End Fence Protection |
| Парткод: | G096 3087 |
| Деталь: | End Fence Compression Spring 3.5N |
| Парткод: | G096 3089 |
| Деталь: | End Fence Lever |
| Парткод: | G096 3086 |
| Деталь: | END FENCE |
| Парткод: | G102 2856 |
| Деталь: | End Fence Tension Spring 12N |
| Парткод: | G096 3090 |
| Деталь: | Rear Paper Tray |
| Парткод: | G096 3060 |
| Деталь: | Rail:End Fence:Auxiliary |
| Парткод: | G102 2814 |
| Деталь: | Protection:Paper Tray:Right |
| Парткод: | G102 2812 |
| Деталь: | Paper Size Sensor Plate |
| Парткод: | G102 2815 |
| Деталь: | Paper Tray Supporting Plate |
| Парткод: | G096 3065 |
| Деталь: | Protection:Paper Size Sensor Plate |
| Парткод: | G102 2832 |
| Деталь: | Guide Plate:Paper Tray |
| Парткод: | G102 2802 |
| Деталь: | Decal:Paper Set Direction:Paper Tray |
| Парткод: | GA00 3118 |
| Деталь: | Cover:Paper Tray |
| Парткод: | G102 2801 |
| Деталь: | Decal:Operate:Paper Tray:Switch:EXP |
| Парткод: | GA00 3150 |
| Деталь: | Decal:Paper Set Direction |
| Парткод: | GA00 3151 |
| Деталь: | PAPER TRAY |
| Парткод: | G096 3051 |
| Деталь: | Seal:Side Fence:Right Front |
| Парткод: | G102 2861 |
| Деталь: | Decal:Base:Size Indication |
| Парткод: | GA00 2023 |
| Деталь: | Wire:High Voltage:Connecting:3 |
| Парткод: | G102 5835 |
| Деталь: | Wire:High Voltage:Connecting:2 |
| Парткод: | G102 5834 |
| Деталь: | Wire:High Voltage:Connecting:1 |
| Парткод: | G102 5833 |
| Деталь: | High Voltage Line:C3 |
| Парткод: | G102 5807 |
| Деталь: | High Voltage Line:T4 |
| Парткод: | G102 5819 |
| Деталь: | High Voltage Line:TS |
| Парткод: | G102 5820 |
| Деталь: | Insulating Sheet:High Voltage Line |
| Парткод: | G102 5809 |
| Деталь: | Supporter:High Voltage Line:1 |
| Парткод: | G102 5805 |
| Деталь: | Supporter:High Voltage Line:2 |
| Парткод: | G102 5818 |
| Деталь: | Spring:Terminal:Power Pack |
| Парткод: | GA06 3047 |
| Деталь: | Terminal:Power Pack |
| Парткод: | G102 5810 |
| Деталь: | Plate Nut:Terminal |
| Парткод: | G102 5817 |
| Деталь: | Holder:Terminal:Power Pack |
| Парткод: | G102 5811 |
| Деталь: | Terminal:Spring Plate:Power Pack:3 |
| Парткод: | G102 5815 |
| Деталь: | Terminal:Spring Plate:Power Pack:6 |
| Парткод: | G102 5814 |
| Деталь: | Terminal:Spring Plate:Power Pack:5 |
| Парткод: | G102 5813 |
| Деталь: | Terminal:Spring Plate:Power Pack:4 |
| Парткод: | G102 5812 |
| Деталь: | Terminal:Spring Plate:Power Pack:7 |
| Парткод: | G102 5816 |
| Деталь: | Harness:High Voltage:By |
| Парткод: | G102 5423 |
| Деталь: | Bracket:Engine Board:Sub-assy |
| Парткод: | G102 5721 |
| Деталь: | Plate:High Voltage Line |
| Парткод: | G102 5838 |
| Деталь: | Harness:EGB-HVP1 |
| Парткод: | G102 5439 |
| Деталь: | Power Pack:Bdtts:G-p2 |
| Парткод: | GZ32 0013 |
| Деталь: | Insulating Sheet:Power Pack:2 |
| Парткод: | G102 5804 |
| Деталь: | PCB:EGB-GP2A:Assy (G160) |
| Парткод: | G158 5121 |
| Деталь: | PCB:EGB-GP2:Assy (G161) |
| Парткод: | G159 5121 |
| Деталь: | Fan:Mm40x15:Nidec:H |
| Парткод: | GX64 0028 |
| Деталь: | Shadeing Plate:Lower |
| Парткод: | G159 5822 |
| Деталь: | Duct:Polygon Scanner |
| Парткод: | G159 5836 |
| Деталь: | Harness:High Voltage:TC |
| Парткод: | G102 5421 |
| Деталь: | Harness:High Voltage:TY |
| Парткод: | G102 5422 |
| Деталь: | Harness:High Voltage:TM |
| Парткод: | G102 5420 |
| Деталь: | Harness:High Voltage:D |
| Парткод: | G102 5425 |
| Деталь: | Harness:PSU-EGB:+5V |
| Парткод: | G102 5437 |
| Деталь: | Harness:EGB-PSU:Control |
| Парткод: | G102 5438 |
| Деталь: | Harness:EGB-HVP2 |
| Парткод: | G102 5440 |
| Деталь: | Harness:Laser Diode:7p |
| Парткод: | G102 5537 |
| Деталь: | Harness:LD:3p |
| Парткод: | G102 5536 |
| Деталь: | Screw:Contact Point |
| Парткод: | AA14 3790 |
| Деталь: | Decal:Size Indication:Manual Feed |
| Парткод: | GA00 3117 |
| Деталь: | Rear Side Fence |
| Парткод: | B039 2632 |
| Деталь: | Front Side Fence |
| Парткод: | B039 2631 |
| Деталь: | MANUAL FEED TABLE |
| Парткод: | G102 2752 |
| Деталь: | Pin:Roller:Tray Bottom Plate:Dia2 |
| Парткод: | GA14 8015 |
| Деталь: | Stopper:Photointerruptor |
| Парткод: | G102 2789 |
| Деталь: | Rack:Side Fence:Front |
| Парткод: | G102 2756 |
| Деталь: | SIDE FENCE GEAR |
| Парткод: | G012 3050 |
| Деталь: | Rack:Side Fence:Rear |
| Парткод: | G102 2755 |
| Деталь: | Cover:DC Solenoid |
| Парткод: | G102 2717 |
| Деталь: | DC Solenoid:24V:9.6W |
| Парткод: | GX11 0019 |
| Деталь: | Guide Plate:Manual Feed:Upper:Assy |
| Парткод: | G102 2720 |
| Деталь: | BUSHING:DIA6:DIA10:9 |
| Парткод: | GA08 2010 |
| Деталь: | Cam:Manual Feed |
| Парткод: | G102 2729 |
| Деталь: | Roller:Guide:Manual Feed |
| Парткод: | G102 2730 |
| Деталь: | Paper Feed Roller:MM30 |
| Парткод: | GF03 1003 |
| Деталь: | Shaft:Manual Feed:Press Fit |
| Парткод: | GA14 0036 |
| Деталь: | Roller:Guide:Tray Bottom Plate |
| Парткод: | GF02 2006 |
| Деталь: | Tray Bottom Plate:Manual Feed:Assy |
| Парткод: | G102 2706 |
| Деталь: | Compression Spring:Manual Feed |
| Парткод: | GA06 3052 |
| Деталь: | Holder:Friction Pad:Manual Feed:Assy |
| Парткод: | G102 2713 |
| Деталь: | Compression Spring:2n |
| Парткод: | GA06 3063 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Guide Plate:Manual Feed:Lower:Assy |
| Парткод: | G102 2701 |
| Деталь: | Gear:38z |
| Парткод: | GB01 3055 |
| Деталь: | Cover:Paper Feed Unit |
| Парткод: | G102 2741 |
| Деталь: | Cover:Manual Feed:Lower |
| Парткод: | G102 2742 |
| Деталь: | Feeler:Paper End |
| Парткод: | G102 2725 |
| Деталь: | Cover:Manual Feed Table |
| Парткод: | G102 2781 |
| Деталь: | Guide:Paper |
| Парткод: | G102 2786 |
| Деталь: | Decal:Caution:Inkjet:NA |
| Парткод: | GA00 3167 |
| Деталь: | Decal:Operate:Manual Feed:EXP |
| Парткод: | GA00 3138 |
| Деталь: | Disc:Manual Feed |
| Парткод: | G102 2715 |
| Деталь: | Tension Spring:Manual Feed:Drive |
| Парткод: | GA06 0059 |
| Деталь: | Harness:Duplex:Manual Feed |
| Парткод: | G102 5461 |
| Деталь: | Stopper:Manual Feed |
| Парткод: | G102 2787 |
| Деталь: | Spacer:Manual Feed Table |
| Парткод: | G102 2790 |
| Деталь: | Cover:Slide:Manual Feed |
| Парткод: | G102 2743 |
| Деталь: | Spring:Slide:Manual Feed:Lower |
| Парткод: | G102 2744 |
| Деталь: | Stopper:Manual Feed Table |
| Парткод: | G102 2793 |
| Деталь: | Sheet:Slider:By-pass Feed |
| Парткод: | G102 2792 |
| Деталь: | Cusion:Cover:By-pass Feed |
| Парткод: | GA16 2011 |
| Деталь: | Magnetic Clutch:Registration:Assy |
| Парткод: | GX20 0014 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2075 |
| Деталь: | Ground Plate:Paper Feed Roller |
| Парткод: | G102 2830 |
| Деталь: | Duct:Fusing |
| Парткод: | G159 1062 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | DC Motor:Shutter:Assy |
| Парткод: | G102 2985 |
| Деталь: | Gear:91z |
| Парткод: | G102 2989 |
| Деталь: | Feeler:Shutter |
| Парткод: | G102 2990 |
| Деталь: | Bracket:Shutter:Assy |
| Парткод: | G102 2982 |
| Деталь: | Ground Plate:Paper Feed |
| Парткод: | G102 2828 |
| Деталь: | Stay:Paper Feed |
| Парткод: | G102 2821 |
| Деталь: | Bracket:Paper Feed:Sensor:Upper |
| Парткод: | G102 2822 |
| Деталь: | Feeler:Paper Size Sensor:Sub |
| Парткод: | G102 2827 |
| Деталь: | Feeler:Paper Volume Sensor |
| Парткод: | G102 2831 |
| Деталь: | Feeler:Paper End Sensor |
| Парткод: | G102 2826 |
| Деталь: | Bracket:Paper Feed:Sensor:Lower |
| Парткод: | G102 2823 |
| Деталь: | Shaft:Paper Feed |
| Парткод: | G102 2824 |
| Деталь: | Compression Spring:Paper Feed |
| Парткод: | G102 2846 |
| Деталь: | Bushing:Paper Feed Roller |
| Парткод: | G102 2825 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | G052 3103 |
| Деталь: | Plate Nut:Shutter |
| Парткод: | G102 2991 |
| Деталь: | Harness:Fusing:Drawer |
| Парткод: | G102 5499 |
| Деталь: | Harness:Paper Feed:Sensor |
| Парткод: | G102 5453 |
| Деталь: | Louver:Duct:Fusing:Left |
| Парткод: | G102 1181 |
| Деталь: | Louver:Duct:Fusing:Right |
| Парткод: | G102 1180 |
| Деталь: | Louver:Duct:Fusing |
| Парткод: | G102 1391 |
| Деталь: | Guide:Stay:Paper Feed:Rear |
| Парткод: | G102 2843 |
| Деталь: | Harness:Power Supply Unit:Heater (NA) |
| Парткод: | G102 5413 |
| Деталь: | Harness:Power Supply Unit:Heater (EU) |
| Парткод: | G102 5414 |
| Деталь: | Screw:Mm5:2.5MM |
| Парткод: | GA14 3003 |
| Деталь: | Bushing:Paper Feed:Middle |
| Парткод: | G102 2819 |
| Деталь: | Discharge Brush:Paper Feed |
| Парткод: | G102 2857 |
| Деталь: | EXIT ROLLER |
| Парткод: | GF02 0035 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Junction Gate |
| Парткод: | GF02 5006 |
| Деталь: | Feeler:Exit:Sub-assy |
| Парткод: | G102 4464 |
| Деталь: | Exit Roller:Driven:Outer |
| Парткод: | GF04 0011 |
| Деталь: | Holder:Exit Roller:Driven:Outer |
| Парткод: | G102 4469 |
| Деталь: | Ring:Exit Roller:Driven |
| Парткод: | G102 4470 |
| Деталь: | Exit Roller:Driven |
| Парткод: | GF04 0012 |
| Деталь: | Holder:Exit Roller:Driven |
| Парткод: | G102 4456 |
| Деталь: | Guide:Positioning:Reverse Roller |
| Парткод: | G102 4453 |
| Деталь: | Relay Sensor |
| Парткод: | AW02 0020 |
| Деталь: | Bracket:Sensor:Exit |
| Парткод: | G102 4462 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0118 |
| Деталь: | Guide Plate:Exit:Upper |
| Парткод: | G102 4452 |
| Деталь: | Discharge Brush:Exit |
| Парткод: | GA12 0010 |
| Деталь: | Stay:Exit |
| Парткод: | G102 4454 |
| Деталь: | Roller:Reverse Roller:Driven |
| Парткод: | GF04 0010 |
| Деталь: | Tension Spring:Reverse:8.1n |
| Парткод: | GA06 0061 |
| Деталь: | Gear:17z |
| Парткод: | GB01 3057 |
| Деталь: | Retaining Ring C - Separate |
| Парткод: | AA10 0014 |
| Деталь: | Ground Plate:Exit |
| Парткод: | G102 4463 |
| Деталь: | Gear:14/20z |
| Парткод: | GB01 7049 |
| Деталь: | Gear:16z |
| Парткод: | GB01 4001 |
| Деталь: | Gear:14z |
| Парткод: | GB01 3056 |
| Деталь: | Guide Plate:Exit:Right |
| Парткод: | G102 4451 |
| Деталь: | Cover:Harness:Exit |
| Парткод: | G102 4467 |
| Деталь: | Lever:Junction Gate |
| Парткод: | G102 4802 |
| Деталь: | Reverse Unit:Dc Solenoid:Assy |
| Парткод: | G102 4505 |
| Деталь: | Fan:Mm40x15:Nidec:L |
| Парткод: | GX64 0029 |
| Деталь: | Bracket:Fan:Paper Exit Unit:Pr |
| Парткод: | G102 5839 |
| Деталь: | Guide Plate:Exit:Lower |
| Парткод: | G102 4450 |
| Деталь: | Guide Roller |
| Парткод: | AF04 0574 |
| Деталь: | Harness:Exit:Sensor |
| Парткод: | G159 5456 |
| Деталь: | Ground Plate:Sensor:Exit |
| Парткод: | G102 4466 |
| Деталь: | Ring:Exit Roller:Dia18 |
| Парткод: | G102 4471 |
| Деталь: | Buffer:Guide Plate:Exit:Lower |
| Парткод: | GA16 2010 |
| Деталь: | Sheet - Duplex Junction |
| Парткод: | G102 4713 |
| Деталь: | Screw - M3x8 |
| Парткод: | B129 3191 |
| Деталь: | Tapping Screr - M3x10 |
| Парткод: | B129 4293 |
| Деталь: | Cover:Bracket:Power Supply Unit |
| Парткод: | G102 5801 |
| Деталь: | Hinge:Exit:Assy |
| Парткод: | GG06 0000 |
| Деталь: | Cover:Exit:Rear |
| Парткод: | G102 1471 |
| Деталь: | Bracket:Exit:Left |
| Парткод: | G102 1364 |
| Деталь: | Decal:Operate:Toner Supply:EXP |
| Парткод: | GA00 3137 |
| Деталь: | Bracket:Exit:Right |
| Парткод: | G102 1363 |
| Деталь: | Decal:Toner Supply:Cover:K |
| Парткод: | GA00 3199 |
| Деталь: | Decal:Toner Supply:Cover:M |
| Парткод: | GA00 3200 |
| Деталь: | Decal:Toner Supply:Cover:C |
| Парткод: | GA00 3201 |
| Деталь: | Decal:Toner Supply:Cover:Y |
| Парткод: | GA00 3202 |
| Деталь: | Cover:Right |
| Парткод: | G102 1481 |
| Деталь: | Louver:MM80 |
| Парткод: | G159 1371 |
| Деталь: | Cap:Louver:Dia80 |
| Парткод: | G102 1376 |
| Деталь: | Cap:Louver:Dia60 |
| Парткод: | G102 1378 |
| Деталь: | Filter:Fan:Fusing |
| Парткод: | GA01 2002 |
| Деталь: | Cap:Louver:Drive |
| Парткод: | G102 1392 |
| Деталь: | Cover:Exit:Front:P2 |
| Парткод: | G159 1461 |
| Деталь: | Seal:Paper Exit Sub-unit:Rear |
| Парткод: | GA15 1026 |
| Деталь: | Shaft:Overflow |
| Парткод: | G102 1367 |
| Деталь: | Stay:Overflow |
| Парткод: | G102 1366 |
| Деталь: | Cover:Harness:Rear |
| Парткод: | G102 1491 |
| Деталь: | Hinge - Front Cover |
| Парткод: | G020 1332 |
| Деталь: | Decal:Operate:Fusing |
| Парткод: | GA00 3132 |
| Деталь: | Bracket:Magnet Catch:Left Rear |
| Парткод: | G102 1357 |
| Деталь: | Bracket:Magnet Catch:Left Front |
| Парткод: | G102 1356 |
| Деталь: | Cover:Left |
| Парткод: | G102 1451 |
| Деталь: | Arm Shaft |
| Парткод: | A680 1443 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG07 1012 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Cushion Sheet:Cover:Exit:Front |
| Парткод: | GA17 4002 |
| Деталь: | Seal:Paper Exit Sub-unit:Lower |
| Парткод: | G159 1250 |
| Деталь: | Seal:Paper Exit Sub-unit:Left Lower |
| Парткод: | G159 1269 |
| Деталь: | Seal:Paper Exit Sub-unit:Left Upper:Side |
| Парткод: | G159 1259 |
| Деталь: | Seal:Paper Exit Sub-unit:Side |
| Парткод: | G159 1251 |
| Деталь: | Filter:fan:electrical Components |
| Парткод: | G159 1252 |
| Деталь: | Guide Plate:Safety Switch |
| Парткод: | G102 5825 |
| Деталь: | Bracket:Safety Switch |
| Парткод: | G102 5824 |
| Деталь: | Torsion Spring:Safety Switch |
| Парткод: | G102 5826 |
| Деталь: | Lever:Lock:Fusing:Left |
| Парткод: | G102 1064 |
| Деталь: | Decal:Operate:Fusing |
| Парткод: | GA00 3132 |
| Деталь: | Inner Cover:Left Front |
| Парткод: | G102 1501 |
| Деталь: | Cover:Main Switch |
| Парткод: | G102 5827 |
| Деталь: | Sheet:Sensor |
| Парткод: | G102 6341 |
| Деталь: | Transfer Belt Contact Motor Assy |
| Парткод: | G102 1350 |
| Деталь: | Ground Wire:Density Sensor |
| Парткод: | G102 5497 |
| Деталь: | Harness:PSU-Powersw |
| Парткод: | G102 5410 |
| Деталь: | Bushing:MM6 |
| Парткод: | A184 1086 |
| Деталь: | Cam:On-off:No.2 |
| Парткод: | G102 1337 |
| Деталь: | Shaft:On-off:No.2 |
| Парткод: | GA14 0000 |
| Деталь: | Guide:Frame |
| Парткод: | G102 6302 |
| Деталь: | Lever:On-off:Transfer Unit |
| Парткод: | G102 6308 |
| Деталь: | Remove Paper Dust:Assy |
| Парткод: | G102 2842 |
| Деталь: | Guide:Transfer Roller:Entrance |
| Парткод: | G102 6307 |
| Деталь: | Lever:Lock:Fusing:Right |
| Парткод: | G102 1063 |
| Деталь: | Bracket:Sensor:On-off:No.2 |
| Парткод: | G102 1320 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Shielding Plate:On-off:No.2 |
| Парткод: | G102 1338 |
| Деталь: | Shutter:Density Sensor:Assy |
| Парткод: | G102 6329 |
| Деталь: | Spur |
| Парткод: | B004 2310 |
| Деталь: | Tension Spring:Cleaner:Density Sensor |
| Парткод: | G102 6334 |
| Деталь: | Cover:Density Sensor |
| Парткод: | G102 6335 |
| Деталь: | DENSITY SENSOR |
| Парткод: | G102 6336 |
| Деталь: | Holder:Density Sensor |
| Парткод: | G102 6333 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Gear:61z |
| Парткод: | GB01 0003 |
| Деталь: | Cover:Remove Paper Dust:Registration |
| Парткод: | G102 2847 |
| Деталь: | Screw:Electrical Components |
| Парткод: | G102 5837 |
| Деталь: | Knob Screw:Control Board |
| Парткод: | G160 5132 |
| Деталь: | Cover:Control Board:Printer |
| Парткод: | G104 5131 |
| Деталь: | PCB:CTL:Gaia-P2:EXP:Sub-Assy |
| Парткод: | G161 5327 |
| Деталь: | Ground Plate:Electrical Components |
| Парткод: | G159 1199 |
| Деталь: | Right Guide 1 |
| Парткод: | G108 5108 |
| Деталь: | Left Guide 1 |
| Парткод: | G108 5107 |
| Деталь: | Panel:Control Board:Printer |
| Парткод: | G104 5133 |
| Деталь: | Grip:Control Board:Printer |
| Парткод: | G104 5134 |
| Деталь: | Panel:Interface |
| Парткод: | G104 5140 |
| Деталь: | Knob Screw:M3 |
| Парткод: | G104 5141 |
| Деталь: | Bracket:Control Board:Printer |
| Парткод: | G104 5130 |
| Деталь: | Bracket:Interface Board:Assy |
| Парткод: | G102 5728 |
| Деталь: | PCB:IOB-GP2 |
| Парткод: | G159 5150 |
| Деталь: | Plate Nut:Electrical Components |
| Парткод: | G102 1057 |
| Деталь: | Temperature & Humidity Sensor |
| Парткод: | AW14 0012 |
| Деталь: | Nut - M3.6 |
| Парткод: | AA10 0006 |
| Деталь: | PCB:DDR-DIMM:128MB:Assy |
| Парткод: | B584 5030 |
| Деталь: | PCB:DDR-DIMM:256MB |
| Парткод: | B585 5030 |
| Деталь: | Panel:Card |
| Парткод: | G104 5137 |
| Деталь: | Bracket:HDD Install |
| Парткод: | G104 5135 |
| Деталь: | Bushing:HDD Unit |
| Парткод: | AA16 1161 |
| Деталь: | Knob Screw:Hdd Unit |
| Парткод: | G104 5139 |
| Деталь: | Knob Screw:HDD |
| Парткод: | G104 5138 |
| Деталь: | Harness:HDD:Raid1:Core:2 |
| Парткод: | G104 5256 |
| Деталь: | Harness:HDD:Power Source |
| Парткод: | G104 5251 |
| Деталь: | PCB:GW HDD:Assy |
| Парткод: | G395 5300 |
| Деталь: | Harness:Sync Detector |
| Парткод: | G102 5451 |
| Деталь: | Harness:Paper Feed:Sensor |
| Парткод: | G102 5453 |
| Деталь: | Harness:Paper Feed:Magnetic Clutch |
| Парткод: | G102 5452 |
| Деталь: | Harness:Drive:Motor:Photoconductor |
| Парткод: | G159 5468 |
| Деталь: | Harness:Duplex:Front:Door:Connecting |
| Парткод: | G159 5460 |
| Деталь: | Harness:IOB:Behind:Assy |
| Парткод: | G159 5448 |
| Деталь: | Harness:IOB-OSU:Connecting:+24V |
| Парткод: | G102 5436 |
| Деталь: | Harness:Option Tray:Drawer |
| Парткод: | G102 5465 |
| Деталь: | Harness:Temperature/humidity Sensor |
| Парткод: | G102 5466 |
| Деталь: | Harness:Drive:Unit:Sensor |
| Парткод: | G102 5538 |
| Деталь: | Harness:Motor:Toner Supply |
| Парткод: | G102 5474 |
| Деталь: | Harness:Toner End Sensor |
| Парткод: | G102 5476 |
| Деталь: | Harness:Duplex:Sensor:Connecting |
| Парткод: | G102 5495 |
| Деталь: | Harness:Il-sw:On-off:Assy |
| Парткод: | G102 5447 |
| Деталь: | Harness:Exit:Cover:Sensor |
| Парткод: | G102 5477 |
| Деталь: | Bracket:Fusingframe:Right:Assy |
| Парткод: | G102 4270 |
| Деталь: | Bracket:Heater:Fusing:Right |
| Парткод: | G102 4242 |
| Деталь: | Heater:NA:850W:120% |
| Парткод: | GX44 0011 |
| Деталь: | Heater:EU:850w:120% |
| Парткод: | GX44 0012 |
| Деталь: | SPRING |
| Парткод: | A250 1388 |
| Деталь: | Spring - Registration Roller |
| Парткод: | A212 2539 |
| Деталь: | Bushing:Cleaning Felt |
| Парткод: | GE03 1010 |
| Деталь: | Bushing:Belt Tensioner |
| Парткод: | GE03 0003 |
| Деталь: | Bracket:Belt Tensioner:P2B:Peen |
| Парткод: | G159 4330 |
| Деталь: | Roller:Belt Tensioner:Fusing Belt |
| Парткод: | GE04 0010 |
| Деталь: | Cleaning Felt:Belt Tension |
| Парткод: | G159 4322 |
| Деталь: | Fusing Cover:Upper |
| Парткод: | G102 4375 |
| Деталь: | Thermistor:Sub-assy (G160) |
| Парткод: | G102 4156 |
| Деталь: | Thermistor:Sub-assy (G161) |
| Парткод: | G159 4156 |
| Деталь: | THERMOSTAT |
| Парткод: | G102 4170 |
| Деталь: | Connector:NA:Assy |
| Парткод: | G102 4352 |
| Деталь: | Connector:Fusing:EU |
| Парткод: | G102 4354 |
| Деталь: | Screw:Drawer |
| Парткод: | AA14 3792 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | Bracket:Heater:Fusing:Left |
| Парткод: | G102 4241 |
| Деталь: | Bracket:Frame:Left:Assy |
| Парткод: | G102 4265 |
| Деталь: | Fusing Cover:Lower |
| Парткод: | G102 4287 |
| Деталь: | Pressure Roller:pFA:Dia30 (G160) |
| Парткод: | GE02 0000 |
| Деталь: | Pressure Roller:pFA:Dia29.6 (G161) |
| Парткод: | GE02 0010 |
| Деталь: | Fusing Entrance Guide Plate |
| Парткод: | G102 4283 |
| Деталь: | Fusing Belt:Dia45:Assy |
| Парткод: | G102 4106 |
| Деталь: | Hot Roller:Dia29 (G160) |
| Парткод: | GE01 0000 |
| Деталь: | Hot Roller:Dia28.65 (G161) |
| Парткод: | GE01 0010 |
| Деталь: | Heat Roller:Dia20 |
| Парткод: | GE01 0001 |
| Деталь: | Decal: High Temperature |
| Парткод: | GA00 0041 |
| Деталь: | Decal: High Temperature |
| Парткод: | GA00 0042 |
| Деталь: | Decal:Fusing |
| Парткод: | GA00 3119 |
Коды ошибок
195
202
203
204
205
210
211
212
213
220
222
224
226
230
231
232
233
234
235
236
237
240
241
242
243
270
300
301
302
303
304
305
306
307
325
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
380
396
397
400
418
442
452
490
491
531
532
541
542
543
544
545
547
557
559
636
670
687
690
818
819
820
821
822
823
824
826
827
828
829
851
853
854
855
856
857
860
861
863
864
865
866
867
868
870
872
873
874
875
876
877
900
920
921
990
991
992
998
Описание
| Error code: | 195 |
| Description: | Serial Number Error |
| Causes: | The serial number stored in the memory (EGB) is not correct. |
| Remedy: | EEPROM defective EGB replaced without original EEPROM |
| Error code: | 202 |
| Display: | ERROR 202 PARAMETER |
| Description: | Polygon motor error 1: ON timeout |
| Causes: | The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed. |
| Error code: | 203 |
| Display: | Power OFF/ON 203:Error ssssssssssssssss |
| Description: | Polygon motor error 2: OFF timeout |
| Causes: | The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off. |
| Error code: | 204 |
| Display: | Power OFF/ON 204:Error |
| Description: | Polygon motor error 3: XSCRDY signal error |
| Causes: | The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing. |
| Remedy: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board). |
| Error code: | 205 |
| Display: | ERROR 205 47V HEAD VOLTAGE |
| Description: | No page at DUP IN (Reserved) |
| Causes: | Disconnected cable from the polygon motor drive board or defective connection. Defective polygon motor or drive board. |
| Remedy: | 1. Check the connectors. 2. Replace the polygon motor. 3. Replace the polygon motor drive board. |
| Error code: | 210 |
| Description: | EM Null page cargo |
| Causes: | • Disconnected or defective harness to synchronizing detector for end position • Defective synchronizing detector board • Defective LD board or driver • Defective EGB |
| Remedy: | 1. Replace the harness of the LD board. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 211 |
| Display: | ERROR 211 HeadWARM.THERM(----) |
| Description: | EM Null page |
| Causes: | • Disconnected or defective harness to synchronizing detector for end position • Defective synchronizing detector board • Defective LD board or driver • Defective EGB |
| Remedy: | 1. Replace the harness of the LD board. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 212 |
| Description: | Install or Reseat Imaging Unit The Imaging Unit CRUM fails to detect the Imaging Unit. |
| Causes: | • Imaging Unit, PL6.1.1 • CRUM Connector, PL7.1.4 • PHD2 Harness, PL7.1.7 • FAN/PHD/MOT Harness, PL10.1.9 |
| Remedy: | 1 Remove the Imaging Unit. Inspect the printer cavity for damage, debris, and toner under the auger area preventing the Imaging Unit from being seated properly. Is there foreign material or damage? Remove foreign material. Vacuum out loose toner if found. Go to Step 2. 2 Inspect and reseat the Imaging Unit. Does the error persist?. Go to Step 3. Complete 3 Check Imaging Unit CRUM connection. Are P/J710 and P/J484 connected? Go to Step 4. Reconnect the CRUM. 4 Check all pins on the PHD2 Harness PL7.1.7 for continuity. 1. Disconnect P/J710 and P/J484. 2. Check continuity between J484<=>J710. Go to Step 5 Replace PHD2 Harness. 5 Check all pins on the FAN/PHD/MOT Harness PL10.1.9 for continuity. 1. Disconnect P/J484 and P/J48. 2. Check continuity between J48 <=> P484. Go to Step 6 Replace the FAN/PHD/MOT Harness 6 Replace the Imaging Unit. Does the error persist? Replace the Engine Control Board. Complete |
| Error code: | 213 |
| Display: | Power OFF/ON 213:Error |
| Description: | Install or Reseat Transfer Roller The printer does not detect the presence of the Transfer Roller. |
| Causes: | • CTD (ADC) Sensor, PL5.2.19 • Transfer Roller, PL5.1.4 • FSR/ADC Harness, PL5.2.28 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Transfer Roller PL5.1.4 • CTD (ADC) Sensor PL5.2.19 Is there any damage? Replace any damaged parts. Go to Step 2. 2 Clean the CTD (ADC) Sensor. Does this fix the problem? Complete Go to Step 3. 3 Test the CTD (ADC) Sensor. Run the Service Diagnostics CTD (ADC) Sensor test. Does the sensor function correctly? Go to Step 4. Go to Step 5. 4 Replace the Transfer Roller. Does the error persist? Go to Step 5. Complete 5 Check the CTD (ADC) Sensor connection. Is P/J136 connected to the harness? Go to Step 6. Connect the sensor. 6 Check all pins on the FSR/ADC Harness PL5.2.28 for continuity. 1. Disconnect P/J36 and P/J136. 2. Check continuity between J36 <=> J136. Go to Step 7. Replace the FSR/ ADC Harness. 7 Check the CTD (ADC) Sensor signal. Disconnect P/J36. Does J36-2 <=> J36-5 = 0 V? Replace the CTD (ADC) Sensor. Replace the Engine Control Board. |
| Error code: | 220 |
| Display: | Service Call 220: Error |
| Description: | Laser Synchronizing Detection Error: [K]/[Y] |
| Causes: | The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Error code: | 222 |
| Description: | Laser Synchronizing Detection Error: [M]/[C] |
| Causes: | The laser synchronizing detection signal for LDB [M]/[C] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Remedy: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB 1. Check the connectors. 2. Replace the laser optics unit. 3. Replace the EGB.· |
| Error code: | 224 |
| Description: | Laser synchronizing detection error: start position [M]: LD0 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 226 |
| Description: | Laser synchronizing detection error: start position [C]: LD0 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 230 |
| Display: | Service Call 230: Error |
| Description: | Paper Jam Clear Paper Path Leave Job in Finisher area 5 |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74. |
| Error code: | 231 |
| Display: | Service Call 231: Error |
| Description: | FGATE OFF error: Bk • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 232 |
| Display: | Service call 232: Error |
| Description: | FGATE ON error: Y The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [Y]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 233 |
| Description: | FGATE OFF error: Y • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [Y]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 234 |
| Description: | FGATE ON error: M The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [M]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 235 |
| Description: | FGATE OFF error: M • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [M]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 236 |
| Description: | FGATE ON error: C The PFGATE ON signal does not assert within 5 seconds after processing the image in normal job or MUSIC for start position [C]. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 237 |
| Description: | FGATE OFF error: C • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [C]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 240 |
| Display: | Service call 240: Error |
| Description: | LD error |
| Causes: | The IPU (EGB) detects a problem at the LD unit. |
| Remedy: | • Worn-out LD • Disconnected or broken harness of the LD. 1. Replace the laser optics unit. |
| Error code: | 241 |
| Display: | Service call 241:Error |
| Description: | LD error: Y The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 242 |
| Display: | Service call 242:Error |
| Description: | LD error: M The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 243 |
| Description: | LD error: C The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 270 |
| Description: | GAVD communication error On startup, Read/Write performed for the same register does not match. |
| Causes: | Defective GAVD. Defective eSOC. Defective BCU. Defective harness. |
| Remedy: | • Turn the main power switch off and on. • Replace the laser optics-housing unit. • Replace the BCU. |
| Error code: | 300 |
| Description: | High voltage power output error |
| Causes: | The measured voltage is not correct when the EGB measures each charge output (charge, development, image transfer belt unit, and transfer unit). |
| Remedy: | • Disconnected or defective high voltage harness • Defective high voltage power supply • Defective EGB 1. Check or replace the harnesses. 2. Replace the high voltage power supply board 3. Replace the EGB. |
| Error code: | 301 |
| Description: | Fuser web must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 303 |
| Display: | SYSTEM HALT (*) 303 : PCB MAIN ET |
| Description: | AC charge output error [Y] The measured voltage is not proper when IOB measures the charge output for each color. |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 304 |
| Display: | ERROR 304 USB INIT ERR |
| Description: | Charge AC bias error [K] The charge current less than 200 mkA is detected. |
| Causes: | Defective charge roller. Defective connectors. Disconnected harness. Defective high voltage power 1. |
| Remedy: | 1. Check the connectors. 2. Replace the PCU for black. 3. Replace the drum positioning plate. |
| Error code: | 305 |
| Display: | ERROR 305 USB TIME OUT |
| Description: | Charge Corona Wire Cleaner Error The charge wire cleaner did not: (1) come from the home position within 5 s, or (2) did return to the home position within 3.75 s due to wire cleaner overload. |
| Causes: | • Cleaner unit blocked or damaged • Until replacement parts become available, set SP2804 to "0" to disable the charge-corona cleaning function so the machine can operate. |
| Error code: | 306 |
| Description: | Charge AC bias error [C] The charge current less than 200 mkA is detected. |
| Causes: | Defective charge roller. Defective connectors. Disconnected harness. Defective high voltage power 1. |
| Remedy: | 1. Check the connectors. 2. Replace the PCU for cyan. 3. Replace the drum positioning plate. 4. Replace the high voltage power 1. |
| Error code: | 307 |
| Description: | Charge AC bias error [Y] The charge current less than 200 mkA is detected. |
| Causes: | Defective charge roller. Defective connectors. Disconnected harness. Defective high voltage power 1. |
| Remedy: | 1. Check the connectors. 2. Replace the PCU for yellow. 3. Replace the drum positioning plate. 4. Replace the high voltage power 1. |
| Error code: | 325 |
| Display: | Open/close cover 325: Paper thickness error |
| Description: | Media detect value out of range. |
| Causes: | 1) Is different media type mixed in? 2) Is media being double fed? |
| Remedy: | Remove foreign objects. |
| Error code: | 360 |
| Display: | Set duplex unit 360: Duplex unit is open. |
| Description: | When duplex unit is removed from printer. |
| Causes: | Does error recover by resetting duplex unit? |
| Remedy: | Normal. Replace duplex unit or engine board. |
| Error code: | 361 |
| Description: | TD sensor (Vt high) error 1: M • The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4.7V) with SP3020-002 for twenty counts. • The [Vt - Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5.0V) with SP3020-001. |
| Causes: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 362 |
| Description: | TD sensor (Vt high) error 1: C • The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4.7V) with SP3020-002 for twenty counts. • The [Vt - Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5.0V) with SP3020-001. |
| Causes: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 363 |
| Description: | TD sensor (Vt high) error 1: Y • The Vt value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 4.7V) with SP3020-002 for twenty counts. • The [Vt - Vtref] value of the black, magenta, cyan, or yellow TD sensor exceeds the specified value (default: 5.0V) with SP3020-001. |
| Causes: | • Black, magenta, cyan, or yellow TD sensor disconnected • Harness between TD sensor and PCU defective • Defective TD sensor |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 364 |
| Description: | TD sensor (Vt low) error 2: K The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 365 |
| Description: | TD sensor (Vt low) error 2: M The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 366 |
| Description: | TD sensor (Vt low) error 2: C The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 367 |
| Description: | TD sensor (Vt low) error 2: Y The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) for 10 counts. |
| Causes: | • TD sensor harness disconnected, loose, defective • A drawer connector disconnected, loose, defective • TD sensor defective |
| Remedy: | 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and PCU for damage. 2. Check the drawer connector. 3. Replace the defective PCU. |
| Error code: | 368 |
| Description: | TD sensor: Initial control voltage error [K] Vt is less than 1 V even though the control power voltage is adjusted to the maximum. Vt is more than 1 V even though the control power voltage is adjusted to the minimum. |
| Causes: | Defective connector connection. Defective TD sensor. The toner density in the developer is different. |
| Remedy: | 1. Replace the PCU. |
| Error code: | 369 |
| Description: | TD sensor: Initial control voltage error [M] Vt is less than 1 V even though the control power voltage is adjusted to the maximum. Vt is more than 1 V even though the control power voltage is adjusted to the minimum. |
| Causes: | Defective connector connection. Defective TD sensor. The toner density in the developer is different. |
| Remedy: | 1. Replace the PCU. |
| Error code: | 370 |
| Display: | Check DUPLEX 370: Paper jam |
| Description: | Paper jam detected after paper rotated in duplex unit. |
| Causes: | Check paper jam in duplex unit. |
| Remedy: | Remove jammed paper. Check/replace duplex unit. |
| Error code: | 371 |
| Display: | Check DUPLEX 371: Paper jam |
| Description: | Paper jam during paper feed from duplex unit. |
| Causes: | Check paper jam in duplex unit. |
| Remedy: | Remove jammed paper. Check/replace duplex unit. |
| Error code: | 372 |
| Display: | Check DUPLEX 372: Paper jam |
| Causes: | Check miss-feed in duplex unit. |
| Remedy: | Remove miss-fed paper and close cover. Check/replace duplex unit. |
| Error code: | 373 |
| Description: | TD sensor adjustment error: M During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.7V) +- 0.2V |
| Causes: | • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective |
| Remedy: | 1. Remove the heat seal from each PCU. 2. Replace the defective PCU. |
| Error code: | 374 |
| Description: | TD sensor adjustment error: C During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.7V) +- 0.2V |
| Causes: | • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective |
| Remedy: | 1. Remove the heat seal from each PCU. 2. Replace the defective PCU. |
| Error code: | 375 |
| Description: | TD sensor adjustment error: Y During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.7V) +- 0.2V |
| Causes: | • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective |
| Remedy: | 1. Remove the heat seal from each PCU. 2. Replace the defective PCU. |
| Error code: | 380 |
| Display: | Open front cover 380: Paper jam |
| Description: | Paper jam during paper feed from cassette 1, 2, 3, 4 or 5 |
| Causes: | Check miss-feed in duplex unit. |
| Remedy: | Remove miss-fed paper and set cassette. Check/replace cassette 1, 2, 3, 4, or 5. |
| Error code: | 396 |
| Description: | Black drum motor error |
| Causes: | The LOCK signal error is detected when the EGB monitors the black drum motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the black drum motor. Replace it if necessary.e hig |
| Error code: | 397 |
| Description: | Color drum motor error |
| Causes: | The LOCK signal error is detected when the EGB monitors the color drum motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the color drum motor. Replace it if necessary. |
| Error code: | 400 |
| Display: | Open top cover 400: Paper size error |
| Description: | TM sensor error |
| Causes: | The CPU detected a low voltage of the positive reflection output under the threshold in the TM sensor. |
| Remedy: | • TM sensors are dirty. • A solid print out due to an electrostatic charging error • The TM sensor is defective. 1. Clean the TM sensors. 2. Replace the TM sensors. 3. Check the image transfer unit. 4. Turn the power Off and On. |
| Error code: | 418 |
| Description: | ID sensor: LED adjustment error LED PWM adjustment is not [A] for three times consecutively. [A] = 50 < [A] < 400 |
| Causes: | Defective ID sensors. Dirty ID sensors or transfer belt. ID sensor life is over. |
| Remedy: | 1. Replace the ID sensors. |
| Error code: | 442 |
| Description: | Image transfer belt contact motor error The image transfer belt contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates. |
| Causes: | Motor overload. Defective motor. Loose connection. Disconnected harness. Shorted 24 V fuse on the PSU. Defective interlock system. Defective IOB. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Replace the interlock switch. • Replace the IOB. |
| Error code: | 452 |
| Description: | Paper transfer unit contact error The paper transfer unit contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates. |
| Causes: | Motor overload. Defective motor. Loose connection. Disconnected harness. Shorted 24 V fuse on the PSU. Defective interlock system. Defective IOB. |
| Remedy: | • Replace the motor. • Reconnect the connector. • Replace the harness. • Shorted 24 V fuse on the PSU. • Repair the interlock system. • Replace the IOB. |
| Error code: | 490 |
| Display: | Set 490: No paper in MP tray (* stands for A4 B4, etc.) |
| Description: | ITB (Image Transfer Belt) Unit Set Error |
| Causes: | The TM sensor does not detect the reflection from the ITB. |
| Remedy: | • No ITB unit in the machine • Dirty TM sensor 1. Check the installation of the ITB unit. 2. Clean the TM sensor.S |
| Error code: | 491 |
| Description: | High voltage power: Drum / development bias output error An error signal is detected for 200 ms when charging the drum or development. |
| Causes: | High voltage leak. Loose connection. Broken harness. Defective drum unit or development unit. Defective high voltage supply unit. |
| Remedy: | • Turn the main power switch off and on. • Reattach/replace the harness and parts on the high voltage power supply route. • Replace the drum unit or development unit. • Replace the high voltage supply unit. |
| Error code: | 531 |
| Description: | Fusing Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the fusing fan motor. |
| Error code: | 532 |
| Description: | IH coil fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH coil fan turns on. |
| Causes: | • Disconnected harness • Overload on the IH coil fan motor • Defective IH coil fan motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the IH coil fan. 3. Replace the IOB. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 557 |
| Description: | Zero Cross Frequency Error |
| Causes: | The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Remedy: | • Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 559 |
| Description: | Consecutive Fusing Jam |
| Causes: | The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF"). |
| Remedy: | • Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 636 |
| Description: | OSM User Code File Error The correct "usercode" file could not be found in the root folder of the SD card because the file is not present, or the existing file is corrupted or the wrong type file. |
| Causes: | • Make sure the eccm.mod file is in the root folder of the SD card. Note: The usercode files are created with the User Setting Tool "IDissuer.exe". |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 687 |
| Description: | Memory address command error |
| Causes: | • Among the I/F commands with the controller, the image transfer available report (for each command) cannot be received. • The image data cannot be prepared at the controller due to a problem. • Communication error • An error has occurred inside the controller. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 690 |
| Description: | GAVD Communication Error |
| Causes: | The ID of the GAVD is not identified during initialization. The chip ID of the GAVD cannot be detected by the machine at power-on. |
| Remedy: | • Defective EGB 1. Replace the EGB. EE |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 826 |
| Display: | SYSTEM HALT (*) 826 : FW/SV MDL |
| Description: | Self-diagnostic Error 5: RTC/Optional NVRAM The NVRAM or optional NVRAM returned an error during the self-diagnostic test. |
| Causes: | • Make sure NVRAM is seated correctly in its socket • Replace the NVRAM on the controller board |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 866 |
| Description: | SD card error 1: Confirmation error The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. |
| Causes: | • Program missing from the SD card |
| Error code: | 867 |
| Description: | SD card error 2: SD card removed The SD card in the boot slot when the machine was turned on was removed while the machine was on. |
| Causes: | • Insert the SD card • Turn the machine’s power off/on |
| Error code: | 868 |
| Description: | SD card error 3: SD card access An error occurred while an SD card was used. |
| Causes: | • SD card not inserted correctly • SD card defective • Controller board defective • To reformat the SC card, use SD Formatter Ver 1.1. |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 872 |
| Description: | HDD Mail Receive Error At power on the HDD unit was detected as defective. Data can be neither read nor written to the HDD. Note: This problem can occur if the machine is switched off while the HDD is being accessed. |
| Causes: | • Format the HDD with SP5832. • HDD defective, replace HDD (be sure to format the new HDD). |
| Error code: | 873 |
| Description: | HDD mail send data error An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD. |
| Causes: | • Do SP5832-1 to format the HDD • Replace the HDD |
| Error code: | 874 |
| Description: | Delete All error 1: HDD A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on, do the operation again. • Install the Data Overwrite Security Unit again. • HDD defective |
| Error code: | 875 |
| Description: | Delete All error 2: Data area An error occurred when the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on and try the operation again. |
| Error code: | 876 |
| Description: | Log Data Errors A problem occurred with the log data at power on or while the machine was operating. |
| Causes: | 1 Log Data Error 1 Log data file corrupted. Occurs at power on or during machine operation. • Format the HDD with SP5832 2 Log Data Error 2 Log data encryption has been enabled but the encryption module has not been installed. Occurs at power on, during machine operation, or after enabling encryption of log data. • Replace the encryption module, reset • Enable encryption 3 Log Data Error 3 Log encryption key has not been enabled (NVRAM malfunction). Occurs at power on. • Format the HDD with SP5832 • Disable log data encryption 4 Log Data Error 4 Occurs at power on. Log data has been encrypted but encryption has been disabled (NVRAM malfunction). -or- Log data has not been encrypted but encryption is enabled (NVRAM malfunction). • Format the HDD with SP5832 5 Log Data Error 5 Occurs at power on. NVRAM has been replaced with the NVRAM from another machine. -or- HDD has been replaced with an HDD unit from another machine. • Replace the NVRAM with the original NVRAM • Replace the HDD with original the HDD • Format the HDD with SP5832 99 Log Data Error 99 Other errors. Occurs at power on or during machine operation. • Contact the machine design section |
| Error code: | 877 |
| Description: | HDD Data Erase Error The Data Overwrite Security option cannot scramble and erase data on the HDD because the DOS SD card has been corrupted or has |
| Causes: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not been removed from the SD card slot. |
| Remedy: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not solve the problem, the SD card has been damaged.) • Install a new NVRAM • Install a new Data Overwrite Security option with a new SD card |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 921 |
| Display: | Power Off/on 921: Error |
| Description: | Fuser Error |
| Causes: | • The font is not on the SD card |
| Remedy: | Indicates that the fuser is below standby temperature when the printer is idle. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
Парткод
Название
RICOH TYPE 145 Блок фотобарабана черный
RICOH TYPE 145 Блок цветных фотобарабанов CMY
RICOH TYPE 4000 Сервисный комплект с печкой
RICOH TYPE 145 Блок переноса изображения
RICOH TYPE 145 Бункер отработанного тонера
RICOH SP-C411 Сервисный комплект с печкой
RICOH TYPE 145 Комплект ролика подачи
RICOH TYPE 245 Тонер-картридж черный (5000 стр.)
RICOH TYPE 245 Тонер-картридж желтый (5000 стр.)
RICOH TYPE 245 Тонер-картридж пурпурный (5000 стр.)
RICOH TYPE 245HY K Тонер-картридж черный (15000 стр.)
RICOH TYPE 245HY Y Тонер-картридж желтый (15000 стр.)
RICOH TYPE 245HY M Тонер-картридж пурпурный (15000 стр.)
RICOH TYPE 245HY C Тонер-картридж голубой (15000 стр.)
RICOH TYPE 245 Тонер-картридж голубой (5000 стр.)
