Ricoh SP5200DN
Рейтинг
Модули
Controller Unit
PAPER TRAY
Paper Exit 2
FRAME SECTION
Paper Transfer 2
Drive Section 1
DRIVE SECTION 2
EXTERIOR 2
LASER UNIT
EXTERIOR 1
FUSING UNIT 1
FUSING UNIT 2
Paper Transfer 1
ELECTRICAL SECTION 1
Paper Feed 1
Paper Exit 1
ELECTRICAL SECTION 3
Paper Regist
Paper Feed 2
ELECTRICAL SECTION 2
Детали Paper Exit 1
| Деталь: | Cover: Left: Terminal: NA |
| Парткод: | M021 1222 |
| Деталь: | Cover: Left: Terminal: EU |
| Парткод: | M021 1211 |
| Деталь: | Knob Screw: M3 |
| Парткод: | G104 5141 |
| Деталь: | Card cover |
| Парткод: | G168 5118 |
| Деталь: | Panel - Interface |
| Парткод: | B132 5836 |
| Деталь: | Panel Knob Screw |
| Парткод: | B622 5825 |
| Деталь: | Ground Plate: Panel |
| Парткод: | B070 6899 |
| Деталь: | Panel: Control Board: Assy |
| Парткод: | M021 1182 |
| Деталь: | PCB: CTL: M020: Assy |
| Парткод: | M020 5372 |
| Деталь: | PCB: CTL: M021: Assy |
| Парткод: | M020 5373 |
| Деталь: | PCB: DDR1-DIMM-32B: 512MB: Assy |
| Парткод: | B585 5140 |
| Деталь: | SD-Card: ENCRY_ZOFFY: EXP: Assy |
| Парткод: | M021 5023 |
| Деталь: | Left Guide 1 |
| Парткод: | G108 5107 |
| Деталь: | Right Guide 1 |
| Парткод: | G108 5108 |
| Деталь: | NVRAM |
| Парткод: | M020 9590 |
| Деталь: | Stepped Screw - M3 |
| Парткод: | AA14 3848 |
| Деталь: | PCB: OPTHDD: SATIE-KAI: Assy |
| Парткод: | M352 5320 |
| Деталь: | Cable: HDD: SATA: Power: Power55 |
| Парткод: | M352 5322 |
| Деталь: | Harness - HDD |
| Парткод: | D362 5132 |
| Деталь: | HDD: 160GB: MK1665GSX |
| Парткод: | D105 5705 |
| Деталь: | Bracket: HDD |
| Парткод: | M001 1108 |
| Деталь: | Rubber Cushion |
| Парткод: | AA16 1125 |
| Деталь: | Base End Fence |
| Парткод: | M021 2565 |
| Деталь: | Rear Tray Paper Feed |
| Парткод: | M021 2551 |
| Деталь: | Supporting Plate: Rear Tray |
| Парткод: | M021 2552 |
| Деталь: | Stopper: Rear Tray |
| Парткод: | M021 2609 |
| Деталь: | Sheet: Holder: Paper Tray |
| Парткод: | M021 2603 |
| Деталь: | Compression Spring: Tray Bottom Plate |
| Парткод: | G102 2817 |
| Деталь: | Friction Pad Adhesion |
| Парткод: | G096 3066 |
| Деталь: | Pressure Plate: End Fence |
| Парткод: | M021 2568 |
| Деталь: | Feeler Paper Volume Bottom Plate Tray |
| Парткод: | M052 2605 |
| Деталь: | Compression Spring Separation |
| Парткод: | M021 2674 |
| Деталь: | Front Tray: Paper Fedd |
| Парткод: | M021 2601 |
| Деталь: | Arm Pressuer Paper Tray |
| Парткод: | M021 2575 |
| Деталь: | Change Feeler: Pressuer: Paper Tray |
| Парткод: | M021 2576 |
| Деталь: | Side Fence: Left |
| Парткод: | M021 2665 |
| Деталь: | Seal: Side Fence: Rear |
| Парткод: | M021 2613 |
| Деталь: | Seal: Side Fence: Front |
| Парткод: | M021 2614 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | M021 2658 |
| Деталь: | Pad: Bottom Plate: Tray |
| Парткод: | M021 2657 |
| Деталь: | Decal: Paper Pressure: Lever |
| Парткод: | M052 6930 |
| Деталь: | Side Fence: Right |
| Парткод: | M021 2656 |
| Деталь: | Gear - 16Z |
| Парткод: | B090 2869 |
| Деталь: | SPRING TENSION |
| Парткод: | G096 3083 |
| Деталь: | Cam: Pressure: Paper Tray |
| Парткод: | M021 2577 |
| Деталь: | Shaft: Pressure: Paper Tray |
| Парткод: | M021 2574 |
| Деталь: | Indicator: Paper Volume: Bottom Plate |
| Парткод: | M021 2581 |
| Деталь: | Weight: Indicator: Paper Volume |
| Парткод: | M021 2582 |
| Деталь: | Cover: Paper Tray: Front |
| Парткод: | M021 2591 |
| Деталь: | Handle: Paper Tray: Front |
| Парткод: | M052 2592 |
| Деталь: | Cover: Paper Tray: Front Upper |
| Парткод: | M021 2593 |
| Деталь: | Guide: Paper Pressure: Tray |
| Парткод: | M021 2572 |
| Деталь: | Change Lever: Pressure: Tray |
| Парткод: | M021 2573 |
| Деталь: | Cover: Paper Size Sensing Plate: Tray |
| Парткод: | M021 2654 |
| Деталь: | Spring: Paper Size Sensing Plate: Tray |
| Парткод: | M021 2655 |
| Деталь: | Plate: Paper Size Sensing: Tray |
| Парткод: | M021 2652 |
| Деталь: | Cap: Paper Tray |
| Парткод: | M021 2553 |
| Деталь: | Tension Spring End Fence |
| Парткод: | M052 2569 |
| Деталь: | End Fence Tension Spring 12N |
| Парткод: | G096 3090 |
| Деталь: | End Fence Compression Spring 3.5N |
| Парткод: | G096 3089 |
| Деталь: | Protection: End Fence |
| Парткод: | M021 2567 |
| Деталь: | Decal: Operating Arrow Direction Right Side Fence |
| Парткод: | M052 2653 |
| Деталь: | Decal: Operating Explanation Extension Tray |
| Парткод: | M052 6933 |
| Деталь: | Decal: Paper Setting |
| Парткод: | M052 6932 |
| Деталь: | Pickoff Pawl: Reverse |
| Парткод: | M052 4495 |
| Деталь: | Torsion Spring: Gate Pawl: M020 |
| Парткод: | M052 4496 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Guide: Reverse: Lower: MF1A |
| Парткод: | M021 4459 |
| Деталь: | Antistatic Brush: Exit |
| Парткод: | M052 4489 |
| Деталь: | Feeler: Exit: Overflow |
| Парткод: | M052 4493 |
| Деталь: | Guide: Exit: Upper |
| Парткод: | M021 4456 |
| Деталь: | Bracket: Sensor: Reverse: P |
| Парткод: | M021 4470 |
| Деталь: | Photointerruptor: LG248NL1 |
| Парткод: | GW02 0020 |
| Деталь: | Ground Plate: Exit Roller |
| Парткод: | M021 4466 |
| Деталь: | Spring Plate: Idler: Reverse |
| Парткод: | M052 4486 |
| Деталь: | Driven Roller: Reverse |
| Парткод: | M052 4485 |
| Деталь: | Roller: Exit: P |
| Парткод: | M021 4468 |
| Деталь: | Roller: Guide |
| Парткод: | M052 4469 |
| Деталь: | Cover: Exit |
| Парткод: | M052 4488 |
| Деталь: | Feeler: Paper Feed Sensor |
| Парткод: | M052 4468 |
| Деталь: | Photo Reflection Sensor: Exit |
| Парткод: | GW01 0007 |
| Деталь: | Exit: Roller Driven |
| Парткод: | M052 4434 |
| Деталь: | Roller: Paper: Exit |
| Парткод: | M052 4875 |
| Деталь: | Right Spring Plate |
| Парткод: | G052 4877 |
| Деталь: | Right Holder - Exit Driven Roller |
| Парткод: | G052 4872 |
| Деталь: | Left Holder - Exit Driven Roller |
| Парткод: | G052 4871 |
| Деталь: | Left Spring Plate |
| Парткод: | G052 4876 |
| Деталь: | Gear: Exit |
| Парткод: | M021 4463 |
| Деталь: | Base: Decurire: Exit |
| Парткод: | M052 4438 |
| Деталь: | M/H Assy: Ground Wire: Exit |
| Парткод: | M021 5419 |
| Деталь: | M/H Assy: Ground Wire: Duplex Sensor |
| Парткод: | M021 5418 |
| Деталь: | Lever: Fusing: Left |
| Парткод: | M052 1053 |
| Деталь: | Lever: Fusing: Right |
| Парткод: | M052 1052 |
| Деталь: | Paper Tray Spring Plate Assy |
| Парткод: | G096 1087 |
| Деталь: | Rubber Foot: FF005-AR79_P4050 |
| Парткод: | M021 1071 |
| Деталь: | Decal: Warning: High Temperatue |
| Парткод: | M052 6926 |
| Деталь: | Cushion: Shutter: AIO |
| Парткод: | M052 1074 |
| Деталь: | Roller: Duplex: Front |
| Парткод: | M021 4612 |
| Деталь: | Guide: Duplex: Rear: Assy |
| Парткод: | M021 4601 |
| Деталь: | Transport Roller: Duplex: Middle: P |
| Парткод: | M021 4994 |
| Деталь: | Ground Plate: Guide: Rear |
| Парткод: | M021 4663 |
| Деталь: | Pulley: Idler: 15T |
| Парткод: | M021 4605 |
| Деталь: | Pulley: Idler |
| Парткод: | M021 4606 |
| Деталь: | Pulley: 25T |
| Парткод: | M021 4608 |
| Деталь: | Synchronous Belt: Rear |
| Парткод: | M052 4996 |
| Деталь: | Bushing - 6x10x9mm |
| Парткод: | AA08 2058 |
| Деталь: | Synchronous Belt: Front |
| Парткод: | M052 4997 |
| Деталь: | Coil Spring: Duplex |
| Парткод: | M021 4625 |
| Деталь: | Guide: Duplex: Front: Assy |
| Парткод: | M021 4610 |
| Деталь: | Guide: Duplex: Feed Paper Again |
| Парткод: | M021 4633 |
| Деталь: | Spring Plate: Feed Paper Again |
| Парткод: | M021 4634 |
| Деталь: | Stepped Screw - M5 |
| Парткод: | B039 4480 |
| Деталь: | Handle: Cover |
| Парткод: | M021 4630 |
| Деталь: | Ground Plate: Guide: Feed Paper Again |
| Парткод: | M021 4662 |
| Деталь: | Decal: Guide Plate: Z2 |
| Парткод: | M052 6921 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 2118 |
| Деталь: | Gear: Manual Feed: No.1 |
| Парткод: | M021 1129 |
| Деталь: | Gear: Connecting: No.1 |
| Парткод: | M021 1128 |
| Деталь: | Gear: Paper Feed: No.3 |
| Парткод: | M021 1127 |
| Деталь: | Gear: Paper Feed: No.2 |
| Парткод: | M021 1126 |
| Деталь: | Gear: Development: No.4: Assy |
| Парткод: | M021 1134 |
| Деталь: | Gear: Joint: Development |
| Парткод: | M021 1136 |
| Деталь: | Coil Spring: Joint: Development |
| Парткод: | M021 1138 |
| Деталь: | Joint: Drive: Development |
| Парткод: | M021 1137 |
| Деталь: | Gear: Fusing: No.1 |
| Парткод: | M021 1145 |
| Деталь: | Gear: Fusing: No.3 |
| Парткод: | M021 1148 |
| Деталь: | Gear: Fusing: No.2 |
| Парткод: | M021 1147 |
| Деталь: | Spring - Paper Exit Release |
| Парткод: | G052 1120 |
| Деталь: | Spacer - Drive Unit |
| Парткод: | G052 1123 |
| Деталь: | Housing: Main |
| Парткод: | M021 1125 |
| Деталь: | Housing: Drive: Sub |
| Парткод: | M052 1141 |
| Деталь: | Gear: Joint: Drum |
| Парткод: | M021 1142 |
| Деталь: | Coil Spring: Joint: Drum |
| Парткод: | M021 1144 |
| Деталь: | Joint: Drive: Drum |
| Парткод: | M021 1143 |
| Деталь: | Electromagnetic Clutch: Registration: Assy |
| Парткод: | M021 2900 |
| Деталь: | Electromagnetic Clutch: Connecting: Assy |
| Парткод: | M021 2835 |
| Деталь: | Electromagnetic Clutch: Paper Feed: Assy |
| Парткод: | M021 2825 |
| Деталь: | Electromagnetic Clutch: 1Turn: Z41: Manual Feed |
| Парткод: | M052 2761 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 2118 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Bracket: Clutch: Feed |
| Парткод: | M052 1168 |
| Деталь: | Cover: Drive: Clutch |
| Парткод: | M052 1195 |
| Деталь: | PHOTOSENSOR |
| Парткод: | G175 2551 |
| Деталь: | Lever: Opener |
| Парткод: | M021 1122 |
| Деталь: | Joint: Drive: Release |
| Парткод: | M021 1121 |
| Деталь: | Coil Spring: Joint: Pressure |
| Парткод: | M021 1123 |
| Деталь: | Plain Shaft Bearing: Frame: Drum |
| Парткод: | M052 1059 |
| Деталь: | DC Stepper Motor: Duplex: Assy |
| Парткод: | M021 4622 |
| Деталь: | Bracket: DC Stepper Motor: P |
| Парткод: | M021 4626 |
| Деталь: | Gear: Drive: Duplex |
| Парткод: | M021 4628 |
| Деталь: | Ground Plate: Bracket: Motor |
| Парткод: | M021 1086 |
| Деталь: | DC Brushless Motor: 46W |
| Парткод: | M021 1108 |
| Деталь: | Bracket: Brushless Motor: Assy |
| Парткод: | M021 1102 |
| Деталь: | Gear: Drum: No.1: Assy |
| Парткод: | M021 1113 |
| Деталь: | Gear: Drum: No.2 |
| Парткод: | M021 1114 |
| Деталь: | Gear: Z73 |
| Парткод: | M021 1111 |
| Деталь: | Gear: Z61 |
| Парткод: | M021 1110 |
| Деталь: | Gear: Z96/Z30 |
| Парткод: | M021 1109 |
| Деталь: | Gear: Paper Feed: No.1 |
| Парткод: | M021 1112 |
| Деталь: | Bracket: Toner End Sensor |
| Парткод: | M052 1061 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 2118 |
| Деталь: | Button: Door: Lever |
| Парткод: | M021 1268 |
| Деталь: | Lever: Door |
| Парткод: | M021 1250 |
| Деталь: | Door: Front |
| Парткод: | M021 1251 |
| Деталь: | Door: Front: EU |
| Парткод: | M021 1201 |
| Деталь: | Feeler: Shutter |
| Парткод: | M021 1254 |
| Деталь: | MAGNETIC CATCH |
| Парткод: | AA02 1031 |
| Деталь: | Link: Door: Front |
| Парткод: | M052 2026 |
| Деталь: | Side Fence: Manual Feed: Left |
| Парткод: | M021 2753 |
| Деталь: | Side Fence: Manual Feed: Right |
| Парткод: | M021 2752 |
| Деталь: | Pad: Base |
| Парткод: | G555 3069 |
| Деталь: | Base: Manual Feed |
| Парткод: | M021 2751 |
| Деталь: | Gear: Side Fence |
| Парткод: | M021 2758 |
| Деталь: | Cover: Front |
| Парткод: | M021 2756 |
| Деталь: | Spring - Bypass |
| Парткод: | G052 3278 |
| Деталь: | Hinge: Cover: Manual Feed |
| Парткод: | M021 2771 |
| Деталь: | MAGNET CATCH |
| Парткод: | B039 1361 |
| Деталь: | Extension Tray: Manual Feed |
| Парткод: | M021 2755 |
| Деталь: | Coil Spring: Button: Door |
| Парткод: | M021 1256 |
| Деталь: | Coil Spring: Link |
| Парткод: | M052 2028 |
| Деталь: | Compression Spring: Door: Lever |
| Парткод: | M052 2027 |
| Деталь: | DecalL: Jam: Repair |
| Парткод: | M052 6922 |
| Деталь: | Decal: Logo: RIC |
| Парткод: | M052 1211 |
| Деталь: | Imaging Unit |
| Парткод: | M001 1904 |
| Деталь: | Roller: Guide |
| Парткод: | M021 3345 |
| Деталь: | Tightener: AIO |
| Парткод: | M021 1052 |
| Деталь: | Coil Spring: Tightener: AIO |
| Парткод: | M021 1054 |
| Деталь: | Cover: Stay: LSU |
| Парткод: | M052 1051 |
| Деталь: | Caution Decal - Laser |
| Парткод: | G111 1910 |
| Деталь: | Drawer: Fusing Sub-Unit: Set Sensor: NA |
| Парткод: | M052 5444 |
| Деталь: | Drawer: Fusing Sub-Unit: Set Sensor: EU |
| Парткод: | M052 5445 |
| Деталь: | Polygon Scanner Motor: DC24V 24W |
| Парткод: | GX06 0029 |
| Деталь: | Screw: Drawer: Fusing |
| Парткод: | M052 1070 |
| Деталь: | Stay: LSU |
| Парткод: | M021 1070 |
| Деталь: | Guide: Sheet: Block: Laser |
| Парткод: | M052 1095 |
| Деталь: | Sheet: Block: Laser |
| Парткод: | M052 1094 |
| Деталь: | Support: Sheet: Block: Laser |
| Парткод: | M052 1096 |
| Деталь: | Decal: High Temperature: Fixation Roller |
| Парткод: | M052 6923 |
| Деталь: | M/H Assy: LDD |
| Парткод: | M021 5413 |
| Деталь: | Harness: Polygon Mirror: Syncdetector: Board |
| Парткод: | G168 5403 |
| Деталь: | Syncronization Detector |
| Парткод: | G052 5060 |
| Деталь: | Cover: Left: NA |
| Парткод: | M021 1214 |
| Деталь: | Cover: Left: EU |
| Парткод: | M021 1213 |
| Деталь: | Duct: Cover: Left |
| Парткод: | M021 1263 |
| Деталь: | SPRING |
| Парткод: | A250 1388 |
| Деталь: | Lever: Exit: P |
| Парткод: | M021 4473 |
| Деталь: | Cover: Rear |
| Парткод: | M021 1275 |
| Деталь: | Guide: Reverse: Exit |
| Парткод: | M021 4472 |
| Деталь: | Cover: Right: NA |
| Парткод: | M021 1228 |
| Деталь: | Cover: Right: EU |
| Парткод: | M021 1227 |
| Деталь: | LOUVER |
| Парткод: | M021 1282 |
| Деталь: | Decal: Main SW: NA: P |
| Парткод: | M052 6936 |
| Деталь: | Decal: Main SW: EU: P |
| Парткод: | M052 6937 |
| Деталь: | Operation Sub-unit: EXP: Assy |
| Парткод: | M021 1401 |
| Деталь: | Guide: Slide: Exit: NA |
| Парткод: | M021 1236 |
| Деталь: | Guide: Slide: Exit: EU |
| Парткод: | M021 1235 |
| Деталь: | Cover: Upper: Middle: NA |
| Парткод: | M021 1219 |
| Деталь: | Cover: Upper: Middle: EU |
| Парткод: | M021 1218 |
| Деталь: | Model Name Plate: M020: RIC |
| Парткод: | M020 6641 |
| Деталь: | Model Name Plate: M021: RIC |
| Парткод: | M021 6641 |
| Деталь: | Plate: Logo: RIC |
| Парткод: | M052 1210 |
| Деталь: | Cushion: Duct: P |
| Парткод: | M021 1264 |
| Деталь: | Decal: Energy Star: PS3: ABS |
| Парткод: | GA00 3245 |
| Деталь: | Decal: Caution: Weight: P |
| Парткод: | M052 6938 |
| Деталь: | Decal: WEEE: EU |
| Парткод: | B121 7450 |
| Деталь: | Decal: Earth: NE: ABS |
| Парткод: | AA00 0267 |
| Деталь: | Fusing Unit: NA |
| Парткод: | M052 0211 |
| Деталь: | Fusing Unit: EU/AP |
| Парткод: | M052 0212 |
| Деталь: | Exit Roller Supporting Plate |
| Парткод: | G096 4638 |
| Деталь: | EXIT ROLLER |
| Парткод: | G800 4854 |
| Деталь: | Exit Roller Holder |
| Парткод: | G052 4639 |
| Деталь: | Guide: Exit: Fusing |
| Парткод: | M052 4200 |
| Деталь: | Spring Plate: Fusing Exit: Assy |
| Парткод: | M052 4235 |
| Деталь: | Plate: Harness: Upper |
| Парткод: | M052 4227 |
| Деталь: | Ground Plate: Fusing |
| Парткод: | M052 4082 |
| Деталь: | Spring - Fusing Stripper |
| Парткод: | M052 4063 |
| Деталь: | Hot Roller Stripper |
| Парткод: | G052 4624 |
| Деталь: | Bracket: Heater: Left |
| Парткод: | M052 4225 |
| Деталь: | Bracket: Bearing: Fusing: Left |
| Парткод: | M052 4231 |
| Деталь: | Cover: Fusing: Left |
| Парткод: | M052 4310 |
| Деталь: | Electrode: Heater |
| Парткод: | M052 4239 |
| Деталь: | Discharge Brush: Hot Roller |
| Парткод: | M052 4237 |
| Деталь: | Plate: Harness: Fusing |
| Парткод: | M042 4226 |
| Деталь: | Drawer: Fusing: 120V |
| Парткод: | M052 5442 |
| Деталь: | Drawer: Fusing: 230V |
| Парткод: | M052 5443 |
| Деталь: | Entrance Guide Plate - Upper |
| Парткод: | G175 4644 |
| Деталь: | Thermostat: Assy |
| Парткод: | M052 4243 |
| Деталь: | Electrode Plate - Right |
| Парткод: | G175 4602 |
| Деталь: | THERMISTOR |
| Парткод: | M052 4241 |
| Деталь: | Cover: Fusing: Right |
| Парткод: | M052 4300 |
| Деталь: | Right Heater Bracket |
| Парткод: | G096 4616 |
| Деталь: | Bracket: Bearing: Fusing: Right |
| Парткод: | M052 4232 |
| Деталь: | Thermal Insulating Bushing |
| Парткод: | AE03 2027 |
| Деталь: | Bearing 30x42x7 |
| Парткод: | G052 4618 |
| Деталь: | Hot Roller |
| Парткод: | M052 4101 |
| Деталь: | Gear: Hot Roller |
| Парткод: | M052 4102 |
| Деталь: | End Ring: Hot Roller |
| Парткод: | M052 4236 |
| Деталь: | Heater: 1025W: 120V: QIRF |
| Парткод: | M052 4115 |
| Деталь: | Heater: 1025W: 220V: QIRF |
| Парткод: | M052 1116 |
| Деталь: | Upper Frame: Fuser |
| Парткод: | M052 4080 |
| Деталь: | Heat Shrinkable Tube: Stripper Pawls |
| Парткод: | M052 4302 |
| Деталь: | Decal: Warning High Temperature: Fusing Unit |
| Парткод: | M052 6924 |
| Деталь: | Driven Roller: Duplex: Drive |
| Парткод: | M052 4618 |
| Деталь: | Compression Spring: 2N |
| Парткод: | M021 4619 |
| Деталь: | Bushing: MM4 |
| Парткод: | D010 4313 |
| Деталь: | Frame: Pressure |
| Парткод: | M052 4071 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | M052 4059 |
| Деталь: | Ball Bearing - 8x16x5 |
| Парткод: | A232 3553 |
| Деталь: | Roller Busing |
| Парткод: | AA08 2073 |
| Деталь: | Cleaning Roller: Assy |
| Парткод: | M052 4202 |
| Деталь: | Compression Spring: Cleaning Roller: |
| Парткод: | M052 4224 |
| Деталь: | Exit Roller: Fusing |
| Парткод: | M052 4066 |
| Деталь: | Discharge Brush: Pressure |
| Парткод: | M052 4053 |
| Деталь: | Ground Plate: Pressure |
| Парткод: | M052 4052 |
| Деталь: | Left Pressure Lever |
| Парткод: | M052 4182 |
| Деталь: | Right Pressure Lever |
| Парткод: | M052 4183 |
| Деталь: | Pressure Spring - Fusing |
| Парткод: | M052 4062 |
| Деталь: | Lever: Pressure |
| Парткод: | M052 4061 |
| Деталь: | Gear: 28T: Fusing: Exit |
| Парткод: | M052 4070 |
| Деталь: | Gear: Exit Roller |
| Парткод: | M052 4228 |
| Деталь: | Shaft: Pressure |
| Парткод: | M052 4055 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 2118 |
| Деталь: | Electrode Plate: Separation |
| Парткод: | M021 3867 |
| Деталь: | Cover: Electrode Plate |
| Парткод: | M021 3868 |
| Деталь: | Guide: Transfer: Upper |
| Парткод: | M021 3861 |
| Деталь: | Ground Plate: Guide: Transport |
| Парткод: | M021 3864 |
| Деталь: | Terminal: Transfer |
| Парткод: | M021 3862 |
| Деталь: | Ground Plate: Guide: Duplex |
| Парткод: | M021 3865 |
| Деталь: | Right Bushing - Transfer |
| Парткод: | G052 3625 |
| Деталь: | Compression Spring: Transfer Roller: |
| Парткод: | M021 3879 |
| Деталь: | Terminal: Separation |
| Парткод: | M021 3863 |
| Деталь: | Registration Guide |
| Парткод: | M021 3866 |
| Деталь: | TRANSFER ROLLER |
| Парткод: | M052 3871 |
| Деталь: | Roller: Positioning: Transfer Roller |
| Парткод: | M052 6251 |
| Деталь: | BUSHING |
| Парткод: | G129 6255 |
| Деталь: | Gear: Transfer Roller |
| Парткод: | M021 6252 |
| Деталь: | Left Bushing - Transfer |
| Парткод: | G052 3626 |
| Деталь: | Compression Spring: Transfer Roller |
| Парткод: | M021 3869 |
| Деталь: | Photointerruptor: LG248NL1 |
| Парткод: | GW02 0020 |
| Деталь: | Sheet: Guide Plate: Transfer |
| Парткод: | M052 3852 |
| Деталь: | Guide Plate: Transfer |
| Парткод: | M052 3851 |
| Деталь: | M/H Assy: High Voltage Line: T |
| Парткод: | M021 5411 |
| Деталь: | Compression Spring: 2N |
| Парткод: | M021 4619 |
| Деталь: | Bushing: MM4 |
| Парткод: | D010 4313 |
| Деталь: | Driven Roller: Duplex |
| Парткод: | M021 4618 |
| Деталь: | Feeler: Duplex: Middle |
| Парткод: | M021 4621 |
| Деталь: | Guide: Transport: Duplex |
| Парткод: | M021 4617 |
| Деталь: | PCB: RFID-R/W |
| Парткод: | M052 5500 |
| Деталь: | DC Fan Motor: MM80: 24V |
| Парткод: | M052 1066 |
| Деталь: | Tapping Screw: M3x33 |
| Парткод: | B259 1119 |
| Деталь: | Shaft: High Voltage: Assy |
| Парткод: | M021 1191 |
| Деталь: | Power Pack |
| Парткод: | M052 5006 |
| Деталь: | M/H Assy: HVP |
| Парткод: | M021 5415 |
| Деталь: | Ground Plate: Roller: Registration: Driven |
| Парткод: | M052 2939 |
| Деталь: | Earth Plate: PSU |
| Парткод: | M052 1092 |
| Деталь: | Cap: Bracket: Power Supply Unit |
| Парткод: | M052 5125 |
| Деталь: | Terminal: Roller |
| Парткод: | A153 2117 |
| Деталь: | Shaft: High Voltage: Assy |
| Парткод: | M052 1191 |
| Деталь: | Spacer: Lower: Body |
| Парткод: | LA25 2536 |
| Деталь: | Earth Plate: Shutter: AIO |
| Парткод: | M052 1047 |
| Деталь: | Screw- M4x6 |
| Парткод: | AA14 3592 |
| Деталь: | M/H Assy: Main SW |
| Парткод: | M021 5409 |
| Деталь: | Inlet: Assy |
| Парткод: | M021 5417 |
| Деталь: | Bracket: Inlet |
| Парткод: | M021 5134 |
| Деталь: | Sheet: Cover: Power Supply Unit: Front |
| Парткод: | M052 5152 |
| Деталь: | Cover: Power Supply Unit: Front |
| Парткод: | M052 1404 |
| Деталь: | Cover: Power Supply Unit: Middle Rear |
| Парткод: | M021 1162 |
| Деталь: | Power Supply Unit: NA |
| Парткод: | GZ23 0053 |
| Деталь: | Power Supply Unit: EU/AA: 170W |
| Парткод: | GZ23 0055 |
| Деталь: | Bracket: Power Supply Unit |
| Парткод: | M021 1101 |
| Деталь: | Roller: Connecting: Lower |
| Парткод: | M021 2831 |
| Деталь: | Roller: Pull Out: Option Tray |
| Парткод: | B090 2742 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2144 |
| Деталь: | Spring - Vertical Transport |
| Парткод: | AA06 3399 |
| Деталь: | Holder: Friction Pad: Manual Feed |
| Парткод: | M021 2711 |
| Деталь: | Compression Spring: Separation: Manual Feed |
| Парткод: | M021 2763 |
| Деталь: | Stay: Manual Feed |
| Парткод: | M021 2701 |
| Деталь: | Supporting Plate: Stay: Manual Feed |
| Парткод: | M021 2702 |
| Деталь: | Mylar: Say: Manual Feed |
| Парткод: | M021 2717 |
| Деталь: | Shaft: Roller: Manual Feed: Assy |
| Парткод: | M021 2730 |
| Деталь: | Cam: Shaft: Manual Feed |
| Парткод: | M021 2722 |
| Деталь: | Roller: Guide: Manual Feed |
| Парткод: | M021 2724 |
| Деталь: | Paper Feed Roller: MM30 |
| Парткод: | GF03 1003 |
| Деталь: | Frame: Manual Feed |
| Парткод: | M021 2762 |
| Деталь: | Feeler: Manual Feed |
| Парткод: | M021 2769 |
| Деталь: | Gear: Connecting: Roller |
| Парткод: | M021 2833 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Mylar Holder: Friction Pad: Manual Feed |
| Парткод: | M021 2712 |
| Деталь: | Balancer: Friction Pad: Manual Feed |
| Парткод: | M021 2713 |
| Деталь: | Rear Mylar Holder: Friction Pad: |
| Парткод: | M052 2714 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 2118 |
| Деталь: | Cover: Upper: Rear: NA |
| Парткод: | M021 1224 |
| Деталь: | Cover: Upper: Rear: EU |
| Парткод: | M021 1223 |
| Деталь: | Cover: Upper: Exit: NA |
| Парткод: | M021 1234 |
| Деталь: | Cover: Upper: Exit: EU |
| Парткод: | M021 1233 |
| Деталь: | Synchronous Belt: Exit |
| Парткод: | M021 4471 |
| Деталь: | DC Stepper Motor: Exit: |
| Парткод: | M021 4404 |
| Деталь: | Bracket: Solenoid |
| Парткод: | M052 4454 |
| Деталь: | Solenoid: Assy: Exit |
| Парткод: | M052 4410 |
| Деталь: | Tension Spring: Driven Roller |
| Парткод: | M021 4402 |
| Деталь: | Photointerruptor: LG248NL1 |
| Парткод: | GW02 0020 |
| Деталь: | M/H Assy: Interlock SW: Rear |
| Парткод: | M021 5412 |
| Деталь: | M/H Assy: Ground Wire: Exit Motor: |
| Парткод: | M021 5421 |
| Деталь: | DC Fan Motor: Mm60 |
| Парткод: | M052 4660 |
| Деталь: | Bracket: Control Board: Assy |
| Парткод: | M021 1171 |
| Деталь: | Ground Plate: Frame: Left: Lower |
| Парткод: | M021 5138 |
| Деталь: | Bracket: Interface: EGB |
| Парткод: | M021 1154 |
| Деталь: | PCB: EGB-Bridge |
| Парткод: | M021 5570 |
| Деталь: | Duct: Fan: PSU |
| Парткод: | M052 1072 |
| Деталь: | Screw: DC Fan Motor: Power Supply Unit: |
| Парткод: | M052 5150 |
| Деталь: | Cover: EGB |
| Парткод: | M021 1153 |
| Деталь: | Registration Roller: Drive |
| Парткод: | M021 2916 |
| Деталь: | Roller Registration Driven 14.12 |
| Парткод: | M021 2917 |
| Деталь: | Sheet: Cleaner: Registration |
| Парткод: | M021 2967 |
| Деталь: | Bracket: Sensor: Registration |
| Парткод: | M021 2968 |
| Деталь: | Photo Reflection Sensor: Exit |
| Парткод: | GW01 0007 |
| Деталь: | Ground Plate: Sensor: Registration |
| Парткод: | M021 2965 |
| Деталь: | Guide Plate: Registration: Upper |
| Парткод: | M021 2966 |
| Деталь: | Seal: Registration Guide: Poron |
| Парткод: | M021 2964 |
| Деталь: | Seal: Guide Plate: Registration: Upper |
| Парткод: | M052 2912 |
| Деталь: | Left Bushing - Registration |
| Парткод: | G052 3258 |
| Деталь: | Spring - Registration Roller |
| Парткод: | AA06 3539 |
| Деталь: | Right Bushing - Registration |
| Парткод: | G052 3257 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2116 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Ground Plate: Shaft: Drive Rollers |
| Парткод: | M021 2844 |
| Деталь: | Decal: Guide Plate: B |
| Парткод: | M052 6920 |
| Деталь: | M/H Assy: Regist Sensor: Connecting |
| Парткод: | M021 5410 |
| Деталь: | Ground Plate: Shaft: Paper Feed |
| Парткод: | M021 2843 |
| Деталь: | Ground Plate: Sensor Board |
| Парткод: | M052 2842 |
| Деталь: | Blocking Cap: Bushing: Registration |
| Парткод: | M052 2919 |
| Деталь: | Guide Mylar: Feed Stay: Upper |
| Парткод: | M021 2804 |
| Деталь: | Roller: Pull Out: Option Tray |
| Парткод: | B090 2742 |
| Деталь: | BUSHING - VERTICAL TRANSPORT |
| Парткод: | AA08 0249 |
| Деталь: | Compression Spring: Connecting Roller: Driven |
| Парткод: | M052 2826 |
| Деталь: | Stay: Paper Feed |
| Парткод: | M021 2801 |
| Деталь: | Ground Plate: Paper Tray: Stay |
| Парткод: | M021 2813 |
| Деталь: | Shield Plate: Paper Feed |
| Парткод: | M021 2815 |
| Деталь: | M/H Assy: Tray |
| Парткод: | M052 5424 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0141 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | G052 3103 |
| Деталь: | Shaft: Paper Feed |
| Парткод: | M021 2814 |
| Деталь: | Compression Spring: Lever: Feed Roller |
| Парткод: | M021 2816 |
| Деталь: | Lever Release Feed Roller |
| Парткод: | M021 2803 |
| Деталь: | Cover: Stay: Left |
| Парткод: | M021 2810 |
| Деталь: | Feeler: Paper End Sensor: Stay |
| Парткод: | M021 2808 |
| Деталь: | Feeler: Paper Volume: Stay |
| Парткод: | M021 2809 |
| Деталь: | Cover: Stay: Right |
| Парткод: | M021 2811 |
| Деталь: | Roller: Connecting: Upper |
| Парткод: | M021 2832 |
| Деталь: | Gear: Connecting: Roller |
| Парткод: | M021 2833 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 2118 |
| Деталь: | PCB: EGB: Assy |
| Парткод: | M021 5010 |
| Деталь: | Bracket: EGB |
| Парткод: | M021 1151 |
| Деталь: | Duct: Upper: Cooling: |
| Парткод: | M052 1067 |
| Деталь: | Duct: lower: Cooling: AIO |
| Парткод: | M052 1068 |
| Деталь: | Tapping Screw: M3x33 |
| Парткод: | B259 1119 |
| Деталь: | Fan: Cooling: |
| Парткод: | M052 1069 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | PCB: Sensor |
| Парткод: | M052 5551 |
| Деталь: | M/H Assy: |
| Парткод: | M052 5428 |
| Деталь: | Thermistor: |
| Парткод: | M021 1253 |
| Деталь: | M/H Assy: Toner End Detection |
| Парткод: | M021 5416 |
| Деталь: | M/H Assy: Interlock SW: Front |
| Парткод: | M021 5403 |
| Деталь: | M/H Assy: Power |
| Парткод: | M021 5400 |
| Деталь: | M/H Assy: Feed: Option |
| Парткод: | M021 5402 |
| Деталь: | M/H Assy: Feed |
| Парткод: | M021 5401 |
| Деталь: | M/H Assy: Exit Sensor |
| Парткод: | M021 5406 |
| Деталь: | M/H Assy: Motor: LSU |
| Парткод: | M021 5420 |
| Деталь: | M/H Assy: HVP |
| Парткод: | M021 5415 |
| Деталь: | Harness Guide: EGB |
| Парткод: | M052 5171 |
| Деталь: | M/H Assy: Fusing: NA |
| Парткод: | M021 5404 |
| Деталь: | M/H Assy: Fusing: EU |
| Парткод: | M021 5405 |
| Деталь: | M/H Assy: PSU Fan: Connecting |
| Парткод: | M021 5422 |
Коды ошибок
195
202
203
204
220
221
230
231
240
312
320
440
500
530
531
532
533
534
541
542
543
544
545
547
557
559
622
623
624
625
641
669
670
671
681
683
688
690
790
819
820
833
851
853
854
855
856
857
858
859
860
861
863
864
865
866
867
868
870
872
873
874
875
876
877
878
900
920
921
990
991
992
995
998
Описание
| Error code: | 195 |
| Description: | Serial Number Error |
| Causes: | The serial number stored in the memory (EGB) is not correct. |
| Remedy: | EEPROM defective EGB replaced without original EEPROM |
| Error code: | 202 |
| Display: | ERROR 202 PARAMETER |
| Description: | Polygon motor error 1: ON timeout |
| Causes: | The polygon mirror motor does not reach the targeted operating speed within 5 sec. after turning on or changing speed. |
| Error code: | 203 |
| Display: | Power OFF/ON 203:Error ssssssssssssssss |
| Description: | Polygon motor error 2: OFF timeout |
| Causes: | The polygon mirror motor does not leave the READY status within 3 sec. after the polygon motor switched off. |
| Error code: | 204 |
| Display: | Power OFF/ON 204:Error |
| Description: | Polygon motor error 3: XSCRDY signal error |
| Causes: | The SCRDY_N signal remains HIGH for 200 ms while the LD unit is firing. |
| Remedy: | • Polygon motor/driver board harness loose or disconnected • Polygon motor/driver board defective • Laser optics unit defective • IPU (EGB) defective 1. Replace the interface harness of the laser optics unit. 2. Replace the laser optics unit. 3. Replace the EGB (Engine Board). |
| Error code: | 220 |
| Display: | Service Call 220: Error |
| Description: | Laser Synchronizing Detection Error: [K]/[Y] |
| Causes: | The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Error code: | 221 |
| Description: | Laser synchronizing detection error: start position [K]: LD1 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 230 |
| Display: | Service Call 230: Error |
| Description: | Paper Jam Clear Paper Path Leave Job in Finisher area 5 |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74. |
| Error code: | 231 |
| Display: | Service Call 231: Error |
| Description: | FGATE OFF error: Bk • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 240 |
| Display: | Service call 240: Error |
| Description: | LD error |
| Causes: | The IPU (EGB) detects a problem at the LD unit. |
| Remedy: | • Worn-out LD • Disconnected or broken harness of the LD. 1. Replace the laser optics unit. |
| Error code: | 312 |
| Description: | AC charge output error [K] The machine detects the AC charge output for each color 0.3 V or less for 0.2 seconds after the machine has started to detect the AC charge output. |
| Causes: | • Loosen or broken harnesses to the HVPS: C/B • Not set or broken PCDU • Defective HVPS: C/B |
| Remedy: | 1. Close the drum securing plate firmly. 2. Make sure that the PCDU terminal plate contacts the machine terminal plate closely at the front side. 3. Set correctly or replace the PCDU. 4. Replace the harnesses to the HVPS: C/B. 5. Replace the HVPS: C/B. |
| Error code: | 320 |
| Display: | Reset fuser 320: Fuser error |
| Description: | Same unit not detected upon power ON or opening cover. |
| Causes: | 1) Is error message displayed? 2) Is fuser unit set properly? 3) Does error reoccur? |
| Remedy: | Check if fuser is set properly. Reset fuser and turn ON power again. Replace fuser unit assembly. |
| Error code: | 440 |
| Description: | Transfer Output Error. A high voltage feedback voltage of less than 0.5 V was detected for 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 500 |
| Description: | Transport/Fusing Motor Error |
| Causes: | The LOCK signal error is detected when the EGB monitors the transport/fusing motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the transport/fusing motor. Replace it if necessary. |
| Error code: | 530 |
| Description: | LSU Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the LSU fan motor. |
| Error code: | 531 |
| Description: | Fusing Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the fusing fan motor. |
| Error code: | 532 |
| Description: | IH coil fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH coil fan turns on. |
| Causes: | • Disconnected harness • Overload on the IH coil fan motor • Defective IH coil fan motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the IH coil fan. 3. Replace the IOB. |
| Error code: | 533 |
| Description: | IH inverter fan error The machine does not detect the fan motor lock signal for 2 seconds while the IH inverter fan turns on. |
| Causes: | • Disconnected harness • Overload on the IH inverter fan motor • Defective IH inverter fan motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the IH inverter fan. 3. Replace the IOB. |
| Error code: | 534 |
| Description: | Second duct fan error The machine does not detect the fan motor lock signal for 2 seconds while the second duct fan turns on. |
| Causes: | • Disconnected harness • Overload on the second duct fan motor • Defective second duct motor • Defective IOB |
| Remedy: | 1. Check or replace the harness. 2. Replace the second duct fan. 3. Replace the IOB. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 557 |
| Description: | Zero Cross Frequency Error |
| Causes: | The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Remedy: | • Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 559 |
| Description: | Consecutive Fusing Jam |
| Causes: | The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF"). |
| Remedy: | • Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 622 |
| Description: | Paper Bank communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The paper bank`s control board is faulty. Defective BCU/IOB. The paper bank`s connection is faulty. |
| Remedy: | • Reconnect the paper bank cables. • Replace the BCU. • Replace the paper bank. • Turn the main power switch off and on. |
| Error code: | 623 |
| Description: | 2nd Paper Bank communication error An error code is issued from the paper bank unit. |
| Causes: | Loose connection. Defective paper bank. |
| Remedy: | • Reconnect the connector. • Replace the paper bank. • Turn the main power switch off and on. |
| Error code: | 624 |
| Description: | 4th Paper Bank (option) communication error This SC is not issued for this machine. When a communication error signal between the 3rd paper bank and 4th paper bank is received. |
| Causes: | • Loose or disconnected connector |
| Remedy: | Check the connection between the main machine and paper feed unit. |
| Error code: | 625 |
| Description: | Paper tray unit communication error bank 4 Three consecutive errors occur during polling, after the paper tray unit has successful I2C communication. |
| Causes: | Disconnect harnesses. Defective Paper tray unit. External noise |
| Remedy: | • Turn the Power Switch Off and On. • Connect the harnesses properly. • Replace the Paper tray unit. |
| Error code: | 641 |
| Description: | BICU control data transfer abnormal A sampling of the control data sent from the BICU reveals an abnormality. |
| Causes: | • Defective controller board • External noise • Defective BCU |
| Remedy: | 1. Replace the controller board. 2. Replace the BCU. |
| Error code: | 669 |
| Description: | EEPROM Error |
| Causes: | An unexpected value exists in the initialization flag of the EEPROM |
| Remedy: | • EEPROM not initialized • Defective EEPROM |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 671 |
| Description: | Engine board mismatch error Engine board and controller mismatch detected. |
| Causes: | • Wrong engine board installed. • Wrong controller board installed. • Check the type of engine board and controller board. |
| Remedy: | 1. Replace the BCU. 2. Replace the controller board. |
| Error code: | 681 |
| Description: | Toner bottle ID: Communication error -01 D Device ID is not identified: K -02 D Device ID is not identified: M -03 D Device ID is not identified: C -04 D Device ID is not identified: Y -06 D Channel error: K -07 D Channel error: M -08 D Channel error: C -09 D Channel error: Y -11 D Device error: K -12 D Device error: M -13 D Device error: C -14 D Device error: Y -16 D Communication interruption (an error during communication): K -17 D Communication interruption (an error during communication): M -18 D Communication interruption (an error during communication): C -19 D Communication interruption (an error during communication): Y -21 D Communication time-out: K -22 D Communication time-out: M -23 D Communication time-out: C -24 D Communication time-out: Y -26 D Device operation suspended (logically suspended): K -27 D Device operation suspended (logically suspended): M -28 D Device operation suspended (logically suspended): C -29 D Device operation suspended (logically suspended): Y -31 D The requested buffer is full: K -32 D The requested buffer is full: M -33 D The requested buffer is full: C -34 D The requested buffer is full: Y -36 D No error code: K -37 D No error code: M -38 D No error code: C -39 D No error code: Y |
| Causes: | Communication error occurs when the toner bottle ID starts to communicate with the toner bottle ID receptor. Retry of toner bottle ID communication fails three times after the machine has detected the toner bottle ID communication error. • 01-04 Damaged memory chip data • 06-09 Disconnected interface • 11-14 No memory chip on the toner cartridge • 16-9, 21-24, 26-39 Caused by noise • 31-34, 36-39 Software problem • Replace the toner bottle detection board. • Replace the toner cartridge. • Turn the main power switch off and on. |
| Error code: | 683 |
| Description: | RFID: Unit check error The machine gets RFID communication error even the toner cartridges have not been installed in the machine |
| Causes: | Caused by noise |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 688 |
| Description: | Ready notification error of image data transmission The controller does not send a ready notification of image data transmission after a sheet of paper has stopped at the registration roller. |
| Causes: | • Controller board defective • Communication error |
| Remedy: | • Turn the Power Switch Off and On. • Replace the engine board. |
| Error code: | 690 |
| Description: | GAVD Communication Error |
| Causes: | The ID of the GAVD is not identified during initialization. The chip ID of the GAVD cannot be detected by the machine at power-on. |
| Remedy: | • Defective EGB 1. Replace the EGB. EE |
| Error code: | 790 |
| Description: | PCB fan error: Folder Unit The machine detected a continuous lock signal from the PCB cooling fan on the PSU for 20 sec. |
| Causes: | • Fan harness connector loose, disconnected, broken • Overload on the fan motor due to physical obstruction such has undetected paper, etc. • Fan defective • MCU folder unit defective |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 833 |
| Display: | SYSTEM HALT (*) 833 : FW/PRN MDL |
| Description: | Self-diagnostic error 8: Engine I/F ASIC |
| Causes: | [0F30] [0F31] • ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. Replace the BCU. [0F41] • ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. Replace the BCU. |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 857 |
| Description: | USB I/F Error The USB driver is not stable and caused an error. |
| Causes: | • Poor USB card connection • Replace the controller board |
| Error code: | 858 |
| Description: | Data encryption conversion error (1) |
| Causes: | -01 A serious error has occurred during the data conversion performed for updating the key for data encryption. • The data in the USB flash drive is damaged. • A communication error has occurred due to electromagnetic waves or other noise. • Replace the controller board. * However, if it is "-30", the machine may recover by turning the main power switch off and then back on. -02 A Data encryption conversion error (2) A serious error occurs when data is encrypted to update an encryption key. Defective NVRAM Replace the controller board. -30 A Data encryption conversion error (3) A recoverable error has occurred before starting data conversion. Defective NVRAM • Turn the main switch off and on. • If the error reoccurs, replace the controller board. -31 A A serious error occurs while the data is encrypted. Same as SC991 Same as SC991 |
| Error code: | 859 |
| Description: | HDD data encryption error |
| Causes: | -01 B HDD check error • Hard disk data conversion has been selected, but the hard disk is not installed. • The hard disk is not mounted properly. • No HDD installed • Hard disk formatting is not completed. • The encryption key on the board and the actual encryption key in the hard disk do not match. • Install the HDD correctly. • Initialize the HDD with SP5-832-001. -02 B Power failure during data encryption. The data conversion in the NVRAM or hard disk has not completed successfully. Power interruption has occurred during the conversion of the data in the NVRAM or hard disk Initialize the HDD with SP5-832-001. -10 B Data Read/Write command error Due to time-out, serial communication error, or other problems in DMAC, an irregular DMAC return value has occurred consecutively two or more times Noise or other problems in the SATA connection Same as SC863 |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 866 |
| Description: | SD card error 1: Confirmation error The machine detected an electronic license error in the application on the SD card in the controller slot immediately after the machine was turned on. |
| Causes: | • Program missing from the SD card |
| Error code: | 867 |
| Description: | SD card error 2: SD card removed The SD card in the boot slot when the machine was turned on was removed while the machine was on. |
| Causes: | • Insert the SD card • Turn the machine’s power off/on |
| Error code: | 868 |
| Description: | SD card error 3: SD card access An error occurred while an SD card was used. |
| Causes: | • SD card not inserted correctly • SD card defective • Controller board defective • To reformat the SC card, use SD Formatter Ver 1.1. |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 872 |
| Description: | HDD Mail Receive Error At power on the HDD unit was detected as defective. Data can be neither read nor written to the HDD. Note: This problem can occur if the machine is switched off while the HDD is being accessed. |
| Causes: | • Format the HDD with SP5832. • HDD defective, replace HDD (be sure to format the new HDD). |
| Error code: | 873 |
| Description: | HDD mail send data error An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD. |
| Causes: | • Do SP5832-1 to format the HDD • Replace the HDD |
| Error code: | 874 |
| Description: | Delete All error 1: HDD A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on, do the operation again. • Install the Data Overwrite Security Unit again. • HDD defective |
| Error code: | 875 |
| Description: | Delete All error 2: Data area An error occurred when the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B735 running from the DOS SD card. |
| Causes: | • Turn the main switch off/on and try the operation again. |
| Error code: | 876 |
| Description: | Log Data Errors A problem occurred with the log data at power on or while the machine was operating. |
| Causes: | 1 Log Data Error 1 Log data file corrupted. Occurs at power on or during machine operation. • Format the HDD with SP5832 2 Log Data Error 2 Log data encryption has been enabled but the encryption module has not been installed. Occurs at power on, during machine operation, or after enabling encryption of log data. • Replace the encryption module, reset • Enable encryption 3 Log Data Error 3 Log encryption key has not been enabled (NVRAM malfunction). Occurs at power on. • Format the HDD with SP5832 • Disable log data encryption 4 Log Data Error 4 Occurs at power on. Log data has been encrypted but encryption has been disabled (NVRAM malfunction). -or- Log data has not been encrypted but encryption is enabled (NVRAM malfunction). • Format the HDD with SP5832 5 Log Data Error 5 Occurs at power on. NVRAM has been replaced with the NVRAM from another machine. -or- HDD has been replaced with an HDD unit from another machine. • Replace the NVRAM with the original NVRAM • Replace the HDD with original the HDD • Format the HDD with SP5832 99 Log Data Error 99 Other errors. Occurs at power on or during machine operation. • Contact the machine design section |
| Error code: | 877 |
| Description: | HDD Data Erase Error The Data Overwrite Security option cannot scramble and erase data on the HDD because the DOS SD card has been corrupted or has |
| Causes: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not been removed from the SD card slot. |
| Remedy: | • If the DOS SD card has been removed, switch the machine off, install the SD card, then switch on the machine. (If this does not solve the problem, the SD card has been damaged.) • Install a new NVRAM • Install a new Data Overwrite Security option with a new SD card |
| Error code: | 878 |
| Description: | TPM electronic recognition error |
| Causes: | -00 The system firmware is not authenticated by TPM. The system hash value registered in the TPM at the machine`s system startup does not match that registered in the USB flash drive. • The system module was updated without going through the formal update process. • Incorrect operating of the USB flash. Replace the board. -01 D USB Flash error An error has occurred in the file system in the USB flash drive. The file system of the USB flash drive is damaged. Replace the controller board. -02 D TPM error An error has occurred in the TPM or TPM driver. Defective TPM Replace the controller board. -03 D TCSD error An error has occurred in the TPM software stack. • The TPM software stack cannot be launched. • The file required for the TPM software stack is missing. Replace the controller board. |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 920 |
| Display: | Power Off/on 920: Error |
| Description: | Fuser Error |
| Causes: | • Software defective • Turn the machine power off/on, or change the controller firmware • Insufficient memory |
| Remedy: | Indicates that the fuser is below temperature when printing. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 921 |
| Display: | Power Off/on 921: Error |
| Description: | Fuser Error |
| Causes: | • The font is not on the SD card |
| Remedy: | Indicates that the fuser is below standby temperature when the printer is idle. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 992 |
| Description: | Temperature/Humidity Sensor Error |
| Causes: | • Turn the main power switch off/on. • Go into the SP mode. Do SP7901 to display details about SC992 (software file name, line number, and variable), and inform your supervisor of the results. |
| Remedy: | 1 Is connector CN18 on the CK1 daughter card board connected properly? Go to step 2. Plug the connector in securely. 2 Replace the temperature and humidity sensor (a component of the paper feed gear). Did this fix the problem? Problem solved. Replace the printer controller board. |
| Error code: | 995 |
| Description: | Finisher Main Feed Motor abnormal |
| Causes: | -01 D • Defective BCU • NVRAM Replacement error • Install the previous NVRAM • Input the serial number with SP5-811-004, and turn the main power switch off and on. -02 D • Defective NVRAM • Defective controller Perform SP5-825 to download the appropriate data to the NVRAM, and then turn the main power switch off and then back on. -03 D The serial number cannot be identified due to a mistake during controller replacement or mechanical failure. Replace the controller with the correct type. -04 D - Place all parts in the initial state, and then replace the parts according to the procedures described in the manuals. |
| Remedy: | 1 Is there jammed paper or other obstructions in the paper path? Clear the paper path. Go to step 2. 2 Check to ensure the connector PJ6 on the finisher control board and the feed motor assembly cable are properly connected. Are the cables properly connected? Go to step 3. Properly connect the cables. 3 Make sure the finisher set switch is activated. Measure for +24 V dc (–10%) between pins 7 and 8 and +5 V dc (–10%) between pins 7 and 6 on the feed motor assembly cable connector CN1. Is either voltage missing? Go to step 4. Go to step 5. 4 Disconnect the feed motor assembly cable and PJ6 on the finisher control board. Measure continuity on the cable for all positions. Is there continuity? Go to step 6. Replace the cable. 5 Replace the feed motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 6 Measure for +24 V dc between pins 1 and 2 on connector PJ3 on the finisher control board. Measure for +5 V dc between pins 1 and 3 on PJ2 on the finisher control board. Is either voltage missing? Replace the power supply. Replace the finisher control board. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
