Ricoh MP1900
Рейтинг
Модули
Optics Section 1 (D096)
Optics Section 3 (D096)
Exterior (D096)
Laser Unit (D096)
Toner Supply Unit (D096)
Drive Section (D096)
Operation Panel (D096)
Optics Section 2 (D096)
Fusing Unit (D096)
Electrical Section 1 (D096)
By-pass Feed Section (D096)
Vertical Transport (D096)
Paper Resistration (D096)
1st Paper Feed Section (D096)
Frame Section (D096)
Paper Exit Section (D096)
PCU 2 (D096)
Paper Cassette (D096)
PCU 1 (D096)
Electrical Section 2 (D096)
Детали Drive Section (D096)
| Деталь: | Shaft:Scale |
| Парткод: | B390 1759 |
| Деталь: | Scale - Left |
| Парткод: | B268 1749 |
| Деталь: | Left Scanner Bracket |
| Парткод: | B039 1710 |
| Деталь: | Photointerruptor:Ee-sx4235a-p2 |
| Парткод: | AW02 0156 |
| Деталь: | Sheet:Photointerruptor |
| Парткод: | A193 1705 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Heater - 9W (120V) |
| Парткод: | A250 1821 |
| Деталь: | Heater - 9W (220V) |
| Парткод: | A250 1822 |
| Деталь: | Inner Cover:Lens |
| Парткод: | B276 1808 |
| Деталь: | Lens Unit |
| Парткод: | B259 1812 |
| Деталь: | Exposure Glass |
| Парткод: | A250 1752 |
| Деталь: | Scale - Inner Back |
| Парткод: | B268 1751 |
| Деталь: | Bracket - Operation Panel |
| Парткод: | B039 1666 |
| Деталь: | Harness - FFC |
| Парткод: | B243 1804 |
| Деталь: | Right Scanner Bracket |
| Парткод: | B039 1712 |
| Деталь: | Exposure Glass Cushion |
| Парткод: | 5442 1924 |
| Деталь: | Rear Scale Bracket |
| Парткод: | B039 1658 |
| Деталь: | Support Bracket |
| Парткод: | B121 1069 |
| Деталь: | ADF Bracket |
| Парткод: | B039 1068 |
| Деталь: | Seal:Exposure Glass |
| Парткод: | B238 1845 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw With Washer - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Rear Scanner Frame |
| Парткод: | B039 1663 |
| Деталь: | Front Scanner Frame |
| Парткод: | B039 1662 |
| Деталь: | Pulley - 37Z |
| Парткод: | B039 1703 |
| Деталь: | Bracket:Idler |
| Парткод: | B039 1705 |
| Деталь: | Spring - Timing Pulley |
| Парткод: | B039 1704 |
| Деталь: | Lens Stay Bracket |
| Парткод: | B121 1667 |
| Деталь: | Timing Belt - 1058.25XL |
| Парткод: | B039 1697 |
| Деталь: | Timing Belt L147 |
| Парткод: | B121 1696 |
| Деталь: | Flange - Pulley |
| Парткод: | B039 1695 |
| Деталь: | Pulley - 37/41Z |
| Парткод: | B039 1694 |
| Деталь: | Scanner Drive Shaft |
| Парткод: | B259 1691 |
| Деталь: | Pulley - 37Z |
| Парткод: | B039 1692 |
| Деталь: | Bracket - Stabilizer Harness |
| Парткод: | B039 1668 |
| Деталь: | Bracket - Timing Belt |
| Парткод: | B121 1664 |
| Деталь: | Stepper Motor:MM42:2.9W |
| Парткод: | B039 1699 |
| Деталь: | Pulley shaft |
| Парткод: | B259 1702 |
| Деталь: | Tension Spring - Stepper Motor |
| Парткод: | B039 1683 |
| Деталь: | Gear - 53Z/60Z |
| Парткод: | B121 1680 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw With Washer - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0487 |
| Деталь: | Bearing 8x22x7 |
| Парткод: | 0805 3530 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006P |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0453 3006N |
| Деталь: | Left Cover NA |
| Парткод: | B121 1316 |
| Деталь: | Left Cover (Except for NA) |
| Парткод: | B121 1315 |
| Деталь: | Cover:Scanner:Left:NA |
| Парткод: | B276 1332 |
| Деталь: | Left Scanner Cover (Except for NA) |
| Парткод: | B039 1302 |
| Деталь: | Cover:Exit:C3-DOM |
| Парткод: | D100 1355 |
| Деталь: | Cover:Scanner:Rear:NA |
| Парткод: | B276 1333 |
| Деталь: | Rear Scanner Cover (Except for NA) |
| Парткод: | B039 1303 |
| Деталь: | Application Cap |
| Парткод: | B121 1314 |
| Деталь: | Cover:Rear:NA |
| Парткод: | B276 1337 |
| Деталь: | Rear Cover B (Except for NA) |
| Парткод: | B121 1336 |
| Деталь: | IC Card Cap |
| Парткод: | B121 1313 |
| Деталь: | Paper Bank Cap |
| Парткод: | B121 1348 |
| Деталь: | Right scanner cover |
| Парткод: | B276 1335 |
| Деталь: | Right Scanner Cover (Except for NA) |
| Парткод: | B039 1304 |
| Деталь: | RIGHT REAR COVER |
| Парткод: | B276 1347 |
| Деталь: | Rear Cover (Except for NA) |
| Парткод: | B039 1317 |
| Деталь: | Cover - Front Right Upper |
| Парткод: | B276 1339 |
| Деталь: | Front Right Upper Cover |
| Парткод: | B039 1309 |
| Деталь: | Cover:Front:NA |
| Парткод: | B276 1351 |
| Деталь: | Cover - Front (Except for NA) |
| Парткод: | B243 1350 |
| Деталь: | Cover Magnet |
| Парткод: | B259 1367 |
| Деталь: | MAGNET CATCH |
| Парткод: | B039 1361 |
| Деталь: | Door - Front NA |
| Парткод: | B243 1254 |
| Деталь: | Door - Front (Except for NA) |
| Парткод: | B243 1253 |
| Деталь: | Model Name Plate:GES (NA/ASIA) |
| Парткод: | D096 7410 |
| Деталь: | Model Name Plate:LAN |
| Парткод: | D096 7413 |
| Деталь: | Model Name Plate:GES (EU) |
| Парткод: | D096 7420 |
| Деталь: | Model Name Plate:NSA (EU) |
| Парткод: | D096 7421 |
| Деталь: | Model Name Plate:REX (EU) |
| Парткод: | D096 7422 |
| Деталь: | Model Name Plate:INF (EU) |
| Парткод: | D096 7426 |
| Деталь: | Model Name Plate:RIC |
| Парткод: | D096 7427 |
| Деталь: | Panel:Logo |
| Парткод: | B132 1531 |
| Деталь: | Sheet - Operation Instructions |
| Парткод: | B039 1365 |
| Деталь: | Rivet - M6 |
| Парткод: | B039 1367 |
| Деталь: | Rivet - M7 |
| Парткод: | B039 1364 |
| Деталь: | Left Upper Cover B |
| Парткод: | B121 1322 |
| Деталь: | Cover:Exit:Rear:B:NA |
| Парткод: | B276 1368 |
| Деталь: | Rear Exit Cover B (Except for NA) |
| Парткод: | B121 1367 |
| Деталь: | Main Switch Cover |
| Парткод: | B039 1362 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M4x8 |
| Парткод: | 0450 4008N |
| Деталь: | Imaging Unit:Assy |
| Парткод: | B283 1876 |
| Деталь: | Cover:Shield Glass |
| Парткод: | B276 1251 |
| Деталь: | Adjusting Plate |
| Парткод: | B039 1905 |
| Деталь: | Discharge Lamp - Ql |
| Парткод: | B259 2381 |
| Деталь: | Harness - Discharge Lamp |
| Парткод: | B121 5204 |
| Деталь: | Sheet - Duct |
| Парткод: | B039 1088 |
| Деталь: | Shield Glass:Assy |
| Парткод: | B283 1961 |
| Деталь: | Decal:LD |
| Парткод: | B283 1981 |
| Деталь: | Sync Detector Mirror |
| Парткод: | AC03 0139 |
| Деталь: | Cylindrical Lens |
| Парткод: | AC02 4009 |
| Деталь: | Cylindrical Lens Holder |
| Парткод: | B039 1942 |
| Деталь: | Holder - Sync Detector Mirror |
| Парткод: | B039 1954 |
| Деталь: | Cover:Assy |
| Парткод: | B283 1971 |
| Деталь: | Harness - Polygon Mirror Motor |
| Парткод: | B121 5439 |
| Деталь: | Harness - Ldd |
| Парткод: | B121 5250 |
| Деталь: | Laser Diode Unit:Assy |
| Парткод: | B276 1917 |
| Деталь: | Polygon Motor - 23622rpm |
| Парткод: | AX06 0323 |
| Деталь: | 2nd Mirror |
| Парткод: | AC03 0138 |
| Деталь: | 2nd Mirror Holder |
| Парткод: | B039 1953 |
| Деталь: | Sync Detector Lenz |
| Парткод: | AC02 0095 |
| Деталь: | Rubber Bushing |
| Парткод: | B121 1975 |
| Деталь: | Tapping Bind Screw - M3x10 |
| Парткод: | 0452 3010N |
| Деталь: | Tapping Screw -3x12 |
| Парткод: | 0450 3012N |
| Деталь: | Tapping Screw:M3x20 |
| Парткод: | 0450 3020N |
| Деталь: | Tapping Screw - M3x14 |
| Парткод: | 0452 3014N |
| Деталь: | TONER SUPPLY UNIT |
| Парткод: | B259 3031 |
| Деталь: | Cam - Handle |
| Парткод: | B039 3360 |
| Деталь: | Bottle Chuck |
| Парткод: | A184 3420 |
| Деталь: | Chuck Shaft |
| Парткод: | A184 3421 |
| Деталь: | Shaft:Slide |
| Парткод: | B259 3422 |
| Деталь: | Shaft - Paper Feed Frame |
| Парткод: | B039 1141 |
| Деталь: | Chuck Spring - Tonner Bottle |
| Парткод: | A267 3556 |
| Деталь: | SLIDER ASSY |
| Парткод: | G020 3334 |
| Деталь: | Harness - High Voltage Line C/T |
| Парткод: | B243 5233 |
| Деталь: | Terminal - Transfer |
| Парткод: | B039 3870 |
| Деталь: | GROUNDING PLATE |
| Парткод: | B039 2578 |
| Деталь: | Cover:Toner Bottle:Assy |
| Парткод: | B039 3381 |
| Деталь: | Harness - Ground Wire |
| Парткод: | B121 5219 |
| Деталь: | Quenching Lamp Terminal |
| Парткод: | B039 2382 |
| Деталь: | Guide Plate - Tonner Supply Unit |
| Парткод: | B039 3392 |
| Деталь: | Total Counter:7FIG:24V |
| Парткод: | AX31 0046 |
| Деталь: | Ground Plate - Toner Supply Unit |
| Парткод: | B039 3395 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
| Деталь: | Brushless Motor DC24V/20W |
| Парткод: | B276 1055 |
| Деталь: | DC Solenoid Assy |
| Парткод: | B259 1135 |
| Деталь: | Timing Belt - 226XL |
| Парткод: | B039 1162 |
| Деталь: | Magnetic Clutch:0.5N m:Z39 |
| Парткод: | B276 1149 |
| Деталь: | Gear - 63Z |
| Парткод: | B039 1170 |
| Деталь: | DC Motor:Toner Bottle:KIR-C3:Assy |
| Парткод: | B276 3310 |
| Деталь: | Bushing - 8x16x9 |
| Парткод: | B039 1144 |
| Деталь: | Electrode Plate:Development:Assy |
| Парткод: | B282 1135 |
| Деталь: | GROUND |
| Парткод: | B282 1128 |
| Деталь: | Large Spring |
| Парткод: | B121 1161 |
| Деталь: | Fusing Swivel Bracket |
| Парткод: | B259 1157 |
| Деталь: | Coupled Gear - 20/49Z (12) |
| Парткод: | B039 1156 |
| Деталь: | Drum Shaft (02) |
| Парткод: | B039 1148 |
| Деталь: | Coupled Gear - 34/63Z (01) |
| Парткод: | B039 1145 |
| Деталь: | Coupled Gear - 32/71Z (04) |
| Парткод: | B039 1146 |
| Деталь: | Gear/pulley - 61/34Z (11) |
| Парткод: | B039 1155 |
| Деталь: | Development Drive Shaft (03) |
| Парткод: | B259 1174 |
| Деталь: | Coupled Gear - 37/97Z (05) |
| Парткод: | B039 1154 |
| Деталь: | Gear - 78Z (06) |
| Парткод: | B039 1173 |
| Деталь: | Gear - 32Z (10) |
| Парткод: | B039 1168 |
| Деталь: | Gear - 22Z (09) |
| Парткод: | B039 1167 |
| Деталь: | Coupled Gear - 49/59/38Z (08) |
| Парткод: | B039 1165 |
| Деталь: | Gear - 37Z (07) |
| Парткод: | B039 1166 |
| Деталь: | Bushing - 8mm |
| Парткод: | 5304 1639 |
| Деталь: | Main Drive Housing |
| Парткод: | B121 1140 |
| Деталь: | Snap Ring - M6 |
| Парткод: | AA10 0015 |
| Деталь: | Harness Hook |
| Парткод: | B121 1145 |
| Деталь: | Small Spring |
| Парткод: | B121 1162 |
| Деталь: | Tapping Screw:M4x10 |
| Парткод: | 0450 4010N |
| Деталь: | TAPPING SCREW |
| Парткод: | 0454 3008Q |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0720 0060E |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0488 |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Cover:Printer:Basic |
| Парткод: | B243 1461 |
| Деталь: | Operation Panel Unit (NA/ASIA) |
| Парткод: | B245 1421 |
| Деталь: | Operation Panel Unit (TWN) |
| Парткод: | B245 1422 |
| Деталь: | Operation Sub-unit:Base:A:EU:Assy |
| Парткод: | D096 1422 |
| Деталь: | Cover:Operation Sub-unit:Lower |
| Парткод: | B276 1452 |
| Деталь: | Cover - Operation Panel |
| Парткод: | B243 1425 |
| Деталь: | GROUND PLATE |
| Парткод: | B039 1469 |
| Деталь: | Keytop - Start |
| Парткод: | B229 1453 |
| Деталь: | Keytop - Clear/Stop |
| Парткод: | B229 1454 |
| Деталь: | Keytop - 10key |
| Парткод: | B229 1475 |
| Деталь: | Keytop - Initial |
| Парткод: | B229 1525 |
| Деталь: | Keytop - Clear Modes |
| Парткод: | B229 1537 |
| Деталь: | Keytop - Power Source |
| Парткод: | B243 1458 |
| Деталь: | Keytop - Cursor |
| Парткод: | B243 1459 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | B259 1499 |
| Деталь: | Sheet:Operation Panel:A:NA/ASIA |
| Парткод: | B245 1472 |
| Деталь: | Sheet:Operation Panel:A:EU/TWN |
| Парткод: | B245 1473 |
| Деталь: | Sheet:Power Source:NA/ASIA |
| Парткод: | B229 1521 |
| Деталь: | Sheet:Power Source:EU/TWN |
| Парткод: | B229 1522 |
| Деталь: | PCB Operation Panel |
| Парткод: | B245 1487 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Screw-m3x5 |
| Парткод: | 0353 0050N |
| Деталь: | 2nd Mirror |
| Парткод: | B039 1787 |
| Деталь: | 2nd Mirror Holder |
| Парткод: | B039 1781 |
| Деталь: | SCANNER DRIVE PULLEY |
| Парткод: | B039 1785 |
| Деталь: | Flexible Board Guide |
| Парткод: | B121 1782 |
| Деталь: | Carriage No.2 Assy |
| Парткод: | B259 1768 |
| Деталь: | Scanner drive belt |
| Парткод: | B039 1784 |
| Деталь: | Idler Belt Pulley Bracket - Rear |
| Парткод: | B259 1778 |
| Деталь: | TENSION SPRING |
| Парткод: | B039 1790 |
| Деталь: | Idler Belt Pulley Bracket - Front |
| Парткод: | B259 1776 |
| Деталь: | Xenon Lamp Mm8 26000/70 |
| Парткод: | B121 1757 |
| Деталь: | Timing Belt Holder - Front |
| Парткод: | B039 1758 |
| Деталь: | No.1 Carriage Assy |
| Парткод: | B121 1751 |
| Деталь: | Timing Belt Holder - Rear |
| Парткод: | B039 1759 |
| Деталь: | No.1 Mirror Clamp |
| Парткод: | B121 1766 |
| Деталь: | No.1 Mirror |
| Парткод: | B121 1762 |
| Деталь: | Xenon Lamp Stabilizer |
| Парткод: | B259 1763 |
| Деталь: | Harness - Stabilizer |
| Парткод: | B259 5223 |
| Деталь: | Slider - Scanner |
| Парткод: | G570 2730 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Fusing Unit:NA:Assy |
| Парткод: | B259 4003 |
| Деталь: | Fusing Unit:EU:Assy |
| Парткод: | B259 4006 |
| Деталь: | Fusing Unit:TWN:Assy |
| Парткод: | B259 4007 |
| Деталь: | Fusing Exit Guide |
| Парткод: | B039 4102 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3870 |
| Деталь: | THERMISTOR |
| Парткод: | AW10 0073 |
| Деталь: | Front Ground Plate |
| Парткод: | B039 4118 |
| Деталь: | THERMOSTAT |
| Парткод: | B039 4120 |
| Деталь: | Fusing Cleaning Roller |
| Парткод: | B259 4015 |
| Деталь: | Spur |
| Парткод: | A232 2374 |
| Деталь: | Stripper Pawl Spring |
| Парткод: | AA06 6637 |
| Деталь: | Stripper Pawls |
| Парткод: | AE04 4062 |
| Деталь: | Front Electrode Plate |
| Парткод: | B121 4111 |
| Деталь: | Thermostat Assy |
| Парткод: | B121 4120 |
| Деталь: | Short Electrode Plate |
| Парткод: | B121 4113 |
| Деталь: | Long Electrode Plate |
| Парткод: | B121 4112 |
| Деталь: | Rear Electrode Plate |
| Парткод: | B121 4114 |
| Деталь: | Rear Heater Holder |
| Парткод: | B259 4091 |
| Деталь: | Heater - 120V/550W |
| Парткод: | B259 4210 |
| Деталь: | Heater - 230v/550w |
| Парткод: | B259 4028 |
| Деталь: | Heater - 110V/600W (TWN) |
| Парткод: | B259 4212 |
| Деталь: | External Circlip |
| Парткод: | G029 4140 |
| Деталь: | Gear - 41Z |
| Парткод: | B039 4171 |
| Деталь: | Bearing 30x42x7 |
| Парткод: | G052 4618 |
| Деталь: | Hot Roller Mm30 |
| Парткод: | AE01 1113 |
| Деталь: | Front Heater Holder |
| Парткод: | B121 4090 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | AE02 0150 |
| Деталь: | Fusing Exit Door |
| Парткод: | B039 4107 |
| Деталь: | Spring - Fusing Exit Guide |
| Парткод: | AA06 6635 |
| Деталь: | Pressure Roller Lever |
| Парткод: | B039 4135 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 2324 |
| Деталь: | Pressure Roller Bushing |
| Парткод: | G029 4174 |
| Деталь: | Frame:Pressure:Printing |
| Парткод: | B245 4054 |
| Деталь: | Stripper Pawls Roller |
| Парткод: | B039 4170 |
| Деталь: | Fusing Entrance Guide Plate |
| Парткод: | B259 4115 |
| Деталь: | Discharge Brush |
| Парткод: | B039 4117 |
| Деталь: | Rear Ground Plate |
| Парткод: | B039 4114 |
| Деталь: | Stripper Pawlsstopper |
| Парткод: | B039 4168 |
| Деталь: | Heater - 120V/600W |
| Парткод: | B259 4215 |
| Деталь: | Heater - 230v/600w |
| Парткод: | B259 4214 |
| Деталь: | Heater - 110V/550W (TWN) |
| Парткод: | B259 4216 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 3570 |
| Деталь: | Roller Busing |
| Парткод: | AA08 2073 |
| Деталь: | Frame:Fusing |
| Парткод: | B259 4103 |
| Деталь: | Hexagonal Bolt:W/Washer:M3x8 |
| Парткод: | 0804 6123 |
| Деталь: | Screw - M4X8 |
| Парткод: | 0954 4008N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Screw - M3X6 |
| Парткод: | 0313 0060N |
| Деталь: | Screw:Polished Round/Spring:M3x10 |
| Парткод: | 0954 3010N |
| Деталь: | Harness - Ground Wire Scanner |
| Парткод: | B121 5208 |
| Деталь: | Guide Mylar |
| Парткод: | B121 5822 |
| Деталь: | Harness - Scanner |
| Парткод: | B245 5222 |
| Деталь: | Harness - Document Feeder |
| Парткод: | B121 5240 |
| Деталь: | ADF Plug Bracket |
| Парткод: | B039 5831 |
| Деталь: | Harness - Density Sensor |
| Парткод: | B121 5206 |
| Деталь: | Screw - M4X6 |
| Парткод: | AA14 3592 |
| Деталь: | Harness - Paper End Sensor No.1 |
| Парткод: | B121 5215 |
| Деталь: | PCB:BICU (NA/EU) |
| Парткод: | D096 5101 |
| Деталь: | PCB:BICU (ASIA/TWN) |
| Парткод: | D096 5103 |
| Деталь: | BICU Bracket |
| Парткод: | B121 5810 |
| Деталь: | Harness - Key Counter |
| Парткод: | B243 5261 |
| Деталь: | Harness - Key Counter Lan |
| Парткод: | B243 5262 |
| Деталь: | Harness - AC Fusing NA |
| Парткод: | B243 5218 |
| Деталь: | Harness - AC Fusing EU |
| Парткод: | B243 5217 |
| Деталь: | Harness - AC Fusing TWN |
| Парткод: | B243 5214 |
| Деталь: | Power Supply Unit (100V) |
| Парткод: | AZ23 0200 |
| Деталь: | Power Supply Unit - 230V |
| Парткод: | AZ23 0219 |
| Деталь: | Choke Coil - B2435018 (230V) |
| Парткод: | B243 5018 |
| Деталь: | Harness - AC Dehumidifier EXP |
| Парткод: | B243 5228 |
| Деталь: | Harness - AC Switch 187 |
| Парткод: | B243 5226 |
| Деталь: | Harness - Power Supply Unit |
| Парткод: | B243 5230 |
| Деталь: | Power Supply Cord Stopper NA Assy |
| Парткод: | B121 5742 |
| Деталь: | Power Supply Cord - 230V |
| Парткод: | B039 5743 |
| Деталь: | Power Supply Cord Bracket |
| Парткод: | B121 5825 |
| Деталь: | Harness - Scanner Motor |
| Парткод: | B121 5200 |
| Деталь: | Harness - Main Motor |
| Парткод: | B243 5203 |
| Деталь: | Harness - High Voltage |
| Парткод: | B243 5231 |
| Деталь: | Harness - Manual Feed |
| Парткод: | B121 5212 |
| Деталь: | Harness - HPS |
| Парткод: | B121 5220 |
| Деталь: | Harness - Discharge Lamp |
| Парткод: | B121 5204 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw - M3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0488 |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0487 |
| Деталь: | Edge Saddle - Les-1010 |
| Парткод: | 1105 0518 |
| Деталь: | Rocker Switch:Sddje33900 |
| Парткод: | 1204 2608 |
| Деталь: | Fuse - 5A 125V |
| Парткод: | 1107 0391 |
| Деталь: | Fuse:Ceramic Case:15A 125V |
| Парткод: | 1107 0629 |
| Деталь: | RAM:FM1608-120-P |
| Парткод: | 1407 5299 |
| Деталь: | Manual Feed Table:Assy |
| Парткод: | B259 2603 |
| Деталь: | Front Side Fence |
| Парткод: | B039 2631 |
| Деталь: | Bottom Plate Pad |
| Парткод: | B039 2628 |
| Деталь: | Rear Side Fence |
| Парткод: | B039 2632 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | B039 2630 |
| Деталь: | Rack - Rear Side Fence |
| Парткод: | B039 2638 |
| Деталь: | Rack - Front Side Fence |
| Парткод: | B039 2637 |
| Деталь: | SIDE FENCE GEAR |
| Парткод: | G012 3050 |
| Деталь: | Spring - By-pass Feed Table |
| Парткод: | AA06 3643 |
| Деталь: | Rotary Switch |
| Парткод: | B039 2645 |
| Деталь: | Stay - Tray Bottom Plate |
| Парткод: | B039 2629 |
| Деталь: | Paper Guide - Extension |
| Парткод: | B039 2620 |
| Деталь: | PAPER GUIDE |
| Парткод: | B039 2621 |
| Деталь: | Magnet Catch - By-pass Feed |
| Парткод: | B121 2617 |
| Деталь: | By-pass Feed Table |
| Парткод: | B039 2619 |
| Деталь: | Lever - By-pass Feed Table |
| Парткод: | G020 2784 |
| Деталь: | Link - By-pass Feed Table |
| Парткод: | B039 2643 |
| Деталь: | Decal - By-pass Feed |
| Парткод: | B039 2633 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Pin - Mm6 |
| Парткод: | B259 2642 |
| Деталь: | LEVER SHAFT |
| Парткод: | B259 2786 |
| Деталь: | Decal - Side Fence |
| Парткод: | B238 2753 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Jam Removal Decal |
| Парткод: | B039 4488 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | B039 2558 |
| Деталь: | RIGHT DOOR |
| Парткод: | B039 2670 |
| Деталь: | Vertical Transport Guide |
| Парткод: | B039 2655 |
| Деталь: | Vertical Transport Guide |
| Парткод: | B039 2653 |
| Деталь: | Lower Guide Plate - By-pass Feed |
| Парткод: | B039 2592 |
| Деталь: | Spring - Friction Pad |
| Парткод: | AA06 3398 |
| Деталь: | Friction pad |
| Парткод: | B039 2596 |
| Деталь: | Spring Plate - Band Stopper |
| Парткод: | A232 3962 |
| Деталь: | Band - Right Door |
| Парткод: | B039 2660 |
| Деталь: | Upper Guide Plate - By-pass Feed |
| Парткод: | B039 2594 |
| Деталь: | Shaft - Feed |
| Парткод: | B259 2594 |
| Деталь: | Gear - 25Z |
| Парткод: | AB01 2313 |
| Деталь: | Right Lower Exit Guide Plate |
| Парткод: | B121 4470 |
| Деталь: | Stepped Screw - M5 |
| Парткод: | B039 4480 |
| Деталь: | Sponge - By-pass Feed |
| Парткод: | B039 2658 |
| Деталь: | By-pass Feed Roller |
| Парткод: | AF03 1060 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Bracket - Paper End Sensor |
| Парткод: | B039 2610 |
| Деталь: | Spring - Paper End Sensor |
| Парткод: | AA06 6343 |
| Деталь: | FEELER - PAPER END SENSOR |
| Парткод: | B039 2611 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Harness - Paper End Sensor |
| Парткод: | B121 5259 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 0514 |
| Деталь: | Right Door Lever |
| Парткод: | B039 2651 |
| Деталь: | SPRING |
| Парткод: | A250 1388 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Bracket - Registration Roller |
| Парткод: | B039 2575 |
| Деталь: | Registration Roller Spring |
| Парткод: | AA06 2254 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Gear - 16Z |
| Парткод: | AB01 2312 |
| Деталь: | Fornt Bushing-registration Roller |
| Парткод: | AA08 0342 |
| Деталь: | Bushing - 8x12x18 |
| Парткод: | AA08 0267 |
| Деталь: | Gear - 18Z |
| Парткод: | AB01 2311 |
| Деталь: | Snap Ring - M6 |
| Парткод: | AA10 0015 |
| Деталь: | TRANSFER UNIT |
| Парткод: | B121 3804 |
| Деталь: | Registration Sensor Spring |
| Парткод: | AA06 6342 |
| Деталь: | Registration Feeler |
| Парткод: | B039 2570 |
| Деталь: | Guide - Right Registration Roller |
| Парткод: | B039 2567 |
| Деталь: | Photointerruptor:Lg248nl1 |
| Парткод: | GW02 0020 |
| Деталь: | Harness - Registration Sensor |
| Парткод: | B121 5202 |
| Деталь: | Registration Cleaning Mylar |
| Парткод: | B039 2560 |
| Деталь: | Guide - Left Registration Roller |
| Парткод: | B039 2572 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | B039 2558 |
| Деталь: | Registration Roller Driven - Dia16 |
| Парткод: | B259 2571 |
| Деталь: | Registration Roller Drive |
| Парткод: | B259 2562 |
| Деталь: | Development Sensor Bracket |
| Парткод: | B039 1130 |
| Деталь: | Harness - Development Sensor |
| Парткод: | B121 5248 |
| Деталь: | Rear Bushing-registration Roller |
| Парткод: | AA08 0343 |
| Деталь: | Bushing - 8x12x22 |
| Парткод: | AA08 2110 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3607 |
| Деталь: | TRANSFER ROLLER |
| Парткод: | B039 3820 |
| Деталь: | DENSITY SENSOR |
| Парткод: | B259 3890 |
| Деталь: | ID Sensor Cover |
| Парткод: | B039 3891 |
| Деталь: | Screw:PCU |
| Парткод: | B259 1131 |
| Деталь: | Harness - Density Sensor |
| Парткод: | B121 5206 |
| Деталь: | Pressure Cover |
| Парткод: | B039 3866 |
| Деталь: | Roller - Transfer Unit |
| Парткод: | B039 3867 |
| Деталь: | Quenching Terminal Plate |
| Парткод: | B039 3863 |
| Деталь: | Registration Guide Spacer |
| Парткод: | B043 2554 |
| Деталь: | HARNESS COVER |
| Парткод: | B121 3860 |
| Деталь: | Quenching Terminal Plate-front |
| Парткод: | B039 3864 |
| Деталь: | Transfer Terminal Plate |
| Парткод: | B039 3865 |
| Деталь: | Front Discharge Brush |
| Парткод: | B120 3862 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | Edge Saddle - LES0510 |
| Парткод: | 1105 0522 |
| Деталь: | Bracket - Paper Size Sensor |
| Парткод: | B039 2754 |
| Деталь: | Push Sw - Paper Size |
| Парткод: | G800 3035 |
| Деталь: | Bracket - Paper End Sensor |
| Парткод: | B039 2736 |
| Деталь: | Paper End Sensor |
| Парткод: | B039 2730 |
| Деталь: | Harness - Paper End Sensor No.1 |
| Парткод: | B121 5215 |
| Деталь: | Snap Ring |
| Парткод: | 5447 2681 |
| Деталь: | Exit Guide Plate |
| Парткод: | B039 2585 |
| Деталь: | Housing - Paper Feed |
| Парткод: | B039 1142 |
| Деталь: | Decal - Exit Paper Feed |
| Парткод: | B039 2834 |
| Деталь: | Mylar - Exit Guide Plate |
| Парткод: | B039 2587 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | B039 2558 |
| Деталь: | Magnetic Clutch:Manual Feed:Assy |
| Парткод: | B276 1152 |
| Деталь: | Right Rail |
| Парткод: | B270 2830 |
| Деталь: | Spring - By-pass Feed |
| Парткод: | B039 1199 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Bushing - By-pass Feed |
| Парткод: | B039 1193 |
| Деталь: | Magnetic Clutch:Paper Feed:Drive:Assy |
| Парткод: | B276 1150 |
| Деталь: | Manual Feed Drivebracket |
| Парткод: | B259 1194 |
| Деталь: | Gear - 19Z |
| Парткод: | B039 1191 |
| Деталь: | Shaft - Drive Manual Feed |
| Парткод: | B259 1190 |
| Деталь: | Shaft:Paper Feed:Drive:Assy |
| Парткод: | B276 1183 |
| Деталь: | BUSHING |
| Парткод: | B121 1188 |
| Деталь: | Paper Feed Drive Bracket |
| Парткод: | B259 1178 |
| Деталь: | Gear - 30Z |
| Парткод: | B039 1187 |
| Деталь: | Gear - 46Z |
| Парткод: | B039 1186 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw With Washer - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Retaining Ring - M4 |
| Парткод: | 0720 0040E |
| Деталь: | Ring Separator |
| Парткод: | 0805 0097 |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0487 |
| Деталь: | Cover:Grip |
| Парткод: | B276 1073 |
| Деталь: | Heater:Paper Feed:No.1:NA:Assy |
| Парткод: | B259 6057 |
| Деталь: | Heater:Paper Feed:No.1:EU:Assy |
| Парткод: | B259 6058 |
| Деталь: | GRIP |
| Парткод: | B276 1072 |
| Деталь: | Grip Bracket 2 |
| Парткод: | B121 1070 |
| Деталь: | Rubber Foot:H5 |
| Парткод: | AH01 0010 |
| Деталь: | Shaft:Door:Right Front:Assy |
| Парткод: | B245 1053 |
| Деталь: | Guide Plate Bracket |
| Парткод: | B121 5802 |
| Деталь: | Choke Coil - B2435018 |
| Парткод: | B243 5018 |
| Деталь: | Power Supply Unit Bracket |
| Парткод: | B121 5801 |
| Деталь: | Front Heater Bracket |
| Парткод: | B121 4201 |
| Деталь: | Holder:Paper Tray |
| Парткод: | B180 2801 |
| Деталь: | Shaft:Door:Right Rear:Assy |
| Парткод: | B259 1058 |
| Деталь: | PUSH SWITCH |
| Парткод: | G020 5626 |
| Деталь: | Harness - AC Dehumidifier |
| Парткод: | B243 5260 |
| Деталь: | Tray Heater (120V) |
| Парткод: | B039 2782 |
| Деталь: | Tray Heater (230V) |
| Парткод: | B039 2783 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0451 3008N |
| Деталь: | Tapping Screw With Washer - M3x6 |
| Парткод: | 0454 3006Q |
| Деталь: | Harness Clamp - LWS-0306ZC |
| Парткод: | 1105 0511 |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0487 |
| Деталь: | WIRE SADDLE |
| Парткод: | 1105 0197 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Screw:Spring Washer:M3x6 |
| Парткод: | 0950 3006N |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0488 |
| Деталь: | Heater Wire Cover |
| Парткод: | B121 1084 |
| Деталь: | Fusing Cover:Paper Exit Sub-unit: One Side:C3bdom:Sub-assy |
| Парткод: | B276 1234 |
| Деталь: | Exit Roller 2 |
| Парткод: | B259 4471 |
| Деталь: | Ring:Exit Roller |
| Парткод: | B039 4473 |
| Деталь: | Bushing - 8x10x5 |
| Парткод: | AA08 2063 |
| Деталь: | Door Switch Bracket |
| Парткод: | B039 1082 |
| Деталь: | Harness - Front Door Switch |
| Парткод: | B121 5205 |
| Деталь: | Door Switch Lever - 7 |
| Парткод: | B039 1096 |
| Деталь: | Door Switch Lever - 8 |
| Парткод: | B039 1123 |
| Деталь: | Door Switch Lever - 6 |
| Парткод: | B039 1095 |
| Деталь: | Door Switch Lever - 5 |
| Парткод: | B039 1094 |
| Деталь: | Door Switch Spring |
| Парткод: | B039 1098 |
| Деталь: | Door Switch Lever - 4 |
| Парткод: | B039 1093 |
| Деталь: | Door Switch Lever - 3 |
| Парткод: | B039 1092 |
| Деталь: | Door Switch Lever - 2 |
| Парткод: | B039 1099 |
| Деталь: | Door Switch Lever - 1 |
| Парткод: | B039 1090 |
| Деталь: | Fusing Grounding Harness |
| Парткод: | B039 4119 |
| Деталь: | Ground Plate - Fusing Unit |
| Парткод: | B039 4116 |
| Деталь: | Exit Photointerruptor Bracket |
| Парткод: | B121 4503 |
| Деталь: | Exit Middle Guide Plate |
| Парткод: | B121 4451 |
| Деталь: | Harness - Paper Feed Sensor |
| Парткод: | B121 5238 |
| Деталь: | Photointerruptor - Duplex |
| Парткод: | G361 5570 |
| Деталь: | ANTISTATIC BRUSH |
| Парткод: | B121 4490 |
| Деталь: | Exit Roller Holder - Inner |
| Парткод: | B039 4459 |
| Деталь: | Turn Roller - Exit Sub-unit |
| Парткод: | G029 4176 |
| Деталь: | Pulley - 23Z |
| Парткод: | B039 1163 |
| Деталь: | Fusing Drive Release Bracket |
| Парткод: | B121 1132 |
| Деталь: | Switch:LF-105-11 |
| Парткод: | B268 1085 |
| Деталь: | Exit Roller Ring Mm14 |
| Парткод: | B121 4473 |
| Деталь: | Harness Guide |
| Парткод: | B121 1126 |
| Деталь: | Outer Exit Cover Roller |
| Парткод: | G052 4873 |
| Деталь: | Short Front Outer Holder |
| Парткод: | B121 4465 |
| Деталь: | Long Rear Middle Holder |
| Парткод: | B121 4469 |
| Деталь: | Short Rear Outer Holder |
| Парткод: | B121 4477 |
| Деталь: | Long Front Middle Holder |
| Парткод: | B121 4467 |
| Деталь: | Exit Lower Guide Plate |
| Парткод: | B121 4461 |
| Деталь: | Tapping Screw:M4x10 |
| Парткод: | 0450 4010N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw:3x12 |
| Парткод: | 0450 3012N |
| Деталь: | RETAINING RING - M3 |
| Парткод: | 0720 0030E |
| Деталь: | PCU Toner Supply Shutter |
| Парткод: | B121 2311 |
| Деталь: | SHUTTER SPRING |
| Парткод: | B039 2312 |
| Деталь: | Drum Shutter |
| Парткод: | B039 2343 |
| Деталь: | Pin - Front Pressure Arm |
| Парткод: | B039 2293 |
| Деталь: | Recycled Toner Coil |
| Парткод: | B039 2272 |
| Деталь: | Front PCU Cover |
| Парткод: | B039 2321 |
| Деталь: | Recycled Toner Plate |
| Парткод: | B039 2274 |
| Деталь: | TONER SUPPLY SEAL |
| Парткод: | B121 2313 |
| Деталь: | Rear Bushing - Toner Coil |
| Парткод: | B039 2276 |
| Деталь: | Drum Holder |
| Парткод: | B039 2350 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3444 |
| Деталь: | Gear - 13Z |
| Парткод: | AB01 1403 |
| Деталь: | Gear - 14Z |
| Парткод: | AB01 1402 |
| Деталь: | Pickoff Pawl |
| Парткод: | B039 2335 |
| Деталь: | Cleaning Blade Assy |
| Парткод: | AD04 2059 |
| Деталь: | Cam - Cleaning Blade |
| Парткод: | B039 2288 |
| Деталь: | OPC Drum |
| Парткод: | B039 9510 |
| Деталь: | Rear Pressure Arm - Charge Roller |
| Парткод: | B039 2295 |
| Деталь: | Charge Roller Spring |
| Парткод: | B039 2287 |
| Деталь: | Front Pressure Arm - Charge Roller |
| Парткод: | B039 2292 |
| Деталь: | Roller:Charge:A3 |
| Парткод: | AD02 7018 |
| Деталь: | Charge Cleaner Brush Roller |
| Парткод: | AD04 2058 |
| Деталь: | OPC Drum Shutter Plate |
| Парткод: | B259 2325 |
| Деталь: | Spacer - M3 |
| Парткод: | B039 2329 |
| Деталь: | Bind Screw - M3x6 |
| Парткод: | 0353 0060N |
| Деталь: | Binding Self-Tapping Screw:M3x12 |
| Парткод: | 0452 3012N |
| Деталь: | Bushing 6x10 |
| Парткод: | 0736 0610 |
| Деталь: | Paper Tray Unit NA |
| Парткод: | B243 2841 |
| Деталь: | Paper Tray Unit EU |
| Парткод: | B243 2840 |
| Деталь: | End Fence:C3 |
| Парткод: | B276 2644 |
| Деталь: | Front Stopper Lever |
| Парткод: | B039 2704 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | B039 2701 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | B039 2707 |
| Деталь: | Side Fence - Front |
| Парткод: | B039 2734 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 5215 2621 |
| Деталь: | Ground Plate - Tray Bottom Plate |
| Парткод: | B039 2712 |
| Деталь: | Side Fence - Rear |
| Парткод: | B039 2731 |
| Деталь: | Rear Stopper Lever |
| Парткод: | B039 2821 |
| Деталь: | Paper Feed Roller Shaft Assy |
| Парткод: | B259 2737 |
| Деталь: | PAPER FEED ROLLER |
| Парткод: | B039 2740 |
| Деталь: | Gear - 16Z |
| Парткод: | A267 2869 |
| Деталь: | Spring:Base:5.8n |
| Парткод: | B276 2719 |
| Деталь: | Ground Plate - Paper Feed Roller |
| Парткод: | B039 2742 |
| Деталь: | Joint - Paper Feed Roller |
| Парткод: | B039 2823 |
| Деталь: | Bushing - 8x12x10 |
| Парткод: | B039 2727 |
| Деталь: | Spring - Paper Feed Roller |
| Парткод: | B039 2732 |
| Деталь: | Friction pad |
| Парткод: | B039 2711 |
| Деталь: | Spring - Friction Pad |
| Парткод: | B039 2713 |
| Деталь: | Paper Size Detector - LT |
| Парткод: | B039 2829 |
| Деталь: | Paper Size Detector - A4 |
| Парткод: | B039 2724 |
| Деталь: | STOPPER BASE |
| Парткод: | A250 2808 |
| Деталь: | Spring - Release Lever |
| Парткод: | G020 2599 |
| Деталь: | Shaft - Joint |
| Парткод: | B039 2739 |
| Деталь: | Decal - Cassette Operation DLT |
| Парткод: | B039 2720 |
| Деталь: | Decal - Cassette Operation |
| Парткод: | B039 2721 |
| Деталь: | Cover - Paper Tray |
| Парткод: | B243 2702 |
| Деталь: | Bottom Plate Pad |
| Парткод: | 5215 2713 |
| Деталь: | PAPER TRAY |
| Парткод: | B243 2701 |
| Деталь: | Rubber Bushing |
| Парткод: | B276 2646 |
| Деталь: | Grip:Option:Paper Tray |
| Парткод: | B272 2510 |
| Деталь: | Retaining Ring - M6 |
| Парткод: | 0805 0088 |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | PCU |
| Парткод: | B259 2210 |
| Деталь: | Rear Drum Stay |
| Парткод: | B259 2371 |
| Деталь: | Development Joint |
| Парткод: | A267 3440 |
| Деталь: | Front Side Plate - Drum |
| Парткод: | B039 2361 |
| Деталь: | Drum Shutter Spring |
| Парткод: | B039 2367 |
| Деталь: | Drum Shutter Gear |
| Парткод: | B039 2362 |
| Деталь: | Development Roller:Assy |
| Парткод: | B259 3052 |
| Деталь: | Case:Development Roller:Assy |
| Парткод: | B039 3159 |
| Деталь: | Development Case Assy |
| Парткод: | B259 3170 |
| Деталь: | Idler Gear - 16z |
| Парткод: | B039 3062 |
| Деталь: | Density Sensor:K-C2.5:Assy |
| Парткод: | B259 3390 |
| Деталь: | Gear - 15Z |
| Парткод: | B039 3245 |
| Деталь: | Development Roller Gear |
| Парткод: | B039 3060 |
| Деталь: | Developer Type 28 Black |
| Парткод: | B121 9640 |
| Деталь: | Screw - M3X6 |
| Парткод: | 0360 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0452 3008N |
| Деталь: | Harness - High Voltage |
| Парткод: | B243 5231 |
| Деталь: | Harness - High Voltage Line C/T |
| Парткод: | B243 5233 |
| Деталь: | Right Door Stopper |
| Парткод: | B039 1073 |
| Деталь: | Upper Main Duct |
| Парткод: | B121 1110 |
| Деталь: | Power Pack BCT |
| Парткод: | AZ32 0152 |
| Деталь: | Frame Duct |
| Парткод: | B121 1112 |
| Деталь: | Lower Main Duct Assy |
| Парткод: | B121 1108 |
| Деталь: | Tapping Screw:M3x33 |
| Парткод: | B259 1119 |
| Деталь: | Fan Motor - Mm80 |
| Парткод: | B259 1106 |
| Деталь: | Exhaust duct |
| Парткод: | B121 1107 |
| Деталь: | Left Duct Assy |
| Парткод: | B121 1109 |
| Деталь: | Harness - High Voltage Line B |
| Парткод: | B243 5232 |
| Деталь: | Spacer - KGLS-12RF |
| Парткод: | G020 5871 |
| Деталь: | Heater Switch Cover |
| Парткод: | B039 5887 |
| Деталь: | Bct Power Pack Bracket |
| Парткод: | B121 5841 |
| Деталь: | Tapping Screw - 3x6 |
| Парткод: | 0451 3006N |
| Деталь: | Tapping Screw - M3x8 |
| Парткод: | 0450 3008N |
| Деталь: | Harness Clamp |
| Парткод: | 1105 0487 |
| Деталь: | Support Spacer - M3x29 |
| Парткод: | 1105 0499 |
| Деталь: | Tapping Screw - M3x10 |
| Парткод: | 0450 3010N |
Коды ошибок
101
120
121
143
144
145
302
320
321
322
390
391
392
401
402
500
541
542
543
544
545
546
547
551
552
553
555
556
559
590
621
760
761
762
901
903
928
929
981
982
Описание
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 143 |
| Display: | Service Call 143:Error |
| Description: | Motor |
| Causes: | • SBU defective • IPU defective • BCU defective • Harness between the SBU and IPU defective • Harness between the BCU-IPU defective • Standard white plate not installed correctly, or is dirty • Scanner mirrors and/or lenses are dirty or installed incorrectly |
| Remedy: | DC pick motor, no encoder feedback - staging motor - replace the “Staging motor” on page 4-79. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 144 |
| Display: | ERROR 144 CARTRIDGE SET ! |
| Description: | Motor |
| Causes: | • SBU defective • BCU defective • Harness between SBU and IPU defective |
| Remedy: | DC motor accel stall - autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 145 |
| Display: | SYSTEM HALT (*) 145 : MAIN CN6,9 CHK |
| Description: | Motor |
| Causes: | • Exposure lamp defective • Dirty white plate • Incorrect position or width of white plate scanning (SP4015) • BICU board defective • SBU board defective |
| Remedy: | DC motor excessive PWM autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 320 |
| Display: | Reset fuser 320: Fuser error |
| Description: | Same unit not detected upon power ON or opening cover. |
| Causes: | 1) Is error message displayed? 2) Is fuser unit set properly? 3) Does error reoccur? |
| Remedy: | Check if fuser is set properly. Reset fuser and turn ON power again. Replace fuser unit assembly. |
| Error code: | 321 |
| Display: | Turn power OFF and wait 321: MOTOR OVERHEAT |
| Description: | Printer cannot be used temporarily due to motor overheat. |
| Remedy: | Turn ON power after a while. |
| Error code: | 322 |
| Description: | Synchronization error The synchronization signal was not issued within 500 ms after the LD fired while the polygon motor was turning at the prescribed number of revolutions. |
| Causes: | • Laser synchronization board connectors or harness loose, disconnected, or damaged • Laser synchronization board defective or out of position • LD drive board defective |
| Remedy: | 1. Check the harness connection of the development HVPS. 2. Replace the development HVPS. 3. Replace the development unit. |
| Error code: | 390 |
| Display: | Check MP tray 390: Paper jam |
| Description: | Paper jam during paper feed from MT. |
| Causes: | Check for miss-fed paper around MT cassette. |
| Remedy: | Remove miss-fed paper and close cover. Check/replace MT. |
| Error code: | 391 |
| Description: | TD sensor error: Auto adjust error During automatic adjustment of the TD sensor, output voltage was less than 1.8V, or more than 4.8V during TD sensor initial setting |
| Causes: | • TD sensor connector or harness loose, broken, defective • TD sensor defective • IOB defective • Toner supply defective (confirm that the toner seal strip has been removed from toner cartridge) |
| Remedy: | 1. Check the harness or harness connection. 2. Clean the surface of the quenching lamp glass. |
| Error code: | 392 |
| Description: | Development Bias Error The development bias feedback voltage was less than 0.3 V for longer than 200 ms while the PWM duty value was more than 5% (indicating a development bias leak). |
| Causes: | • Bias terminal damaged • High voltage cable damaged, defective • CGB power pack defective |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 402 |
| Display: | ERROR 402 MOTOR Y |
| Description: | ID Sensor Vsp Error The Vsp level was twice detected at 0V or at more than 2.5 V. |
| Causes: | • Under the left upper cover, make sure that the hex screw of the main drum drive gear is tight • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • Development unit defective • CGB power pack defective |
| Error code: | 500 |
| Description: | Transport/Fusing Motor Error |
| Causes: | The LOCK signal error is detected when the EGB monitors the transport/fusing motor state. (This monitoring is done immediately after power-on, when the motor starts rotating, and immediately after the motor stops.) |
| Remedy: | • Disconnected or defective motor harness. • Motor slips due to excessive load 1. Check the harness from the transport/fusing motor. Replace it if necessary. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 546 |
| Description: | Fusing Temperature: Error 4 The machine detected that the fusing temperature was fluctuating out of range for more than 60 sec. (7 readings detected temperature fluctuating more than ±20C) |
| Causes: | • Thermistor connection loose, disconnected, defective • Hot roller thermistor not positioned correctly • Fusing lamp connections loose, disconnected, defective • MCU defective |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 551 |
| Description: | Pressure roller center thermistor error 1. During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the pressure roller center thermistor measured a value higher than 3.3V 10 consecutive times at 600 ms intervals. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 552 |
| Description: | Fusing sleeve belt warm-up error 2 The fusing sleeve belt temperature does not reach 81C for 6 seconds after the inverter turned on.) |
| Causes: | Dirty thermopile lenses. Deformed thermistor. |
| Error code: | 553 |
| Description: | Pressure roller center thermistor error 2 During the hot roller temperature control sequence, the pressure roller center thermistor measures a value lower than 0.2V. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 555 |
| Description: | Fusing Heater error: End The fusing heater keeps full power for 9 seconds or more. |
| Causes: | Defective thermistors. Broken heater cables. |
| Error code: | 556 |
| Description: | Unstable fusing temperature (rear) The fusing temperature varies 50° C or more within 1 second, and this occurs 2 consecutive times. |
| Causes: | • Thermistor defective or out of position • Power supply unit defective |
| Error code: | 559 |
| Description: | Consecutive Fusing Jam |
| Causes: | The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF"). |
| Remedy: | • Defective fusing unit • Defective fusing control 1. Clear this SC to send a command after a jam removal. 2. Turn off this function after a jam removal. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 590 |
| Description: | Toner collection motor error The toner collection motor sensor output does not change for 3 seconds while the toner collection motor is on. |
| Causes: | • Motor lock due to obstruction • Motor driver board defective • Motor connection loose, defective • Toner collection motor sensor disconnected, sensor defective • Rotational transmission shaft (o6 x 30) missing |
| Error code: | 621 |
| Display: | ERROR 621 POSITIVE P.OVER |
| Description: | Finisher/Mail box communication error An error occurs during line connection. A communication error report is received from the UART. |
| Causes: | The finisher`s control board is faulty. Defective BCU/IOB. The finisher`s connection is faulty. Reconnect the finisher/mail box cables. |
| Remedy: | • Reconnect the finisher/mail box cables. • Replace the BCU. • Replace the finisher/mail box. • Turn the main power switch off and on. |
| Error code: | 760 |
| Description: | Finisher punch motor error The punch HP sensor is not activated within the specified time after the punch motor turned on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Punch HP sensor disconnected, defective • Punch motor disconnected or defective • Punch motor overload due to obstruction |
| Remedy: | 1. Check the connections and cables for the punch motor and HP sensor. 2. Check for blockages in the punch motor mechanism. 3. Replace the punch HP sensor and/or punch motor 4. Replace the finisher main board. |
| Error code: | 761 |
| Description: | Finisher folder plate motor error The folder plate moves but is not detected at the home position within the specified time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Folder plate HP sensor disconnected, defective • Folder plate motor disconnected, defective • Folder plate motor overloaded due to obstruction. |
| Remedy: | 1. Check the connections and cables for the folder plate motor and HP sensor. 2. Check for blockages in the folder plate motor mechanism. 3. Replace the folder plate HP sensor and/or folder plate motor 4. Replace the finisher main board. |
| Error code: | 762 |
| Description: | Front fold plate HP sensor error The state (on/off, off/on) of the front fold plate HP sensor in the fan fold unit did not change 1 sec. after the plate started to move. |
| Causes: | • Fold plate motor (F) harness connector loose, disconnected, broken • Front fold plate HP sensor harness connector loose, disconnected, broken • Fold plate motor (F) defective • Front fold plate HP sensor defective • Undetected paper is jamming the action of the motor or fold plate • Fan folder unit MCU defective |
| Error code: | 901 |
| Display: | Power OFF/ON 901:Error |
| Description: | Engine flash error |
| Causes: | Indicates that the flash which the system board code is programmed into is bad. Replace the system board. |
| Remedy: | Replace the system board. |
| Error code: | 903 |
| Display: | Power OFF/ON 903:Error |
| Description: | Paperport link driver error |
| Causes: | These errors indicate an unrecoverable system software error. |
| Remedy: | Replace the system board. |
| Error code: | 928 |
| Display: | Power Off/on 928: Error |
| Description: | Failure in the Fuser Motor The Fuser Motor has stopped rotating. Applicable Status Code: Code 928: The Fuser Motor has failed. |
| Causes: | • Fuser Motor, PL2.1.9 • Motor Driver Board, PL2.1.10 • Engine Control Board, PL1.1.4 |
| Remedy: | 1 Test the Fuser Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Fuser Motor test. Does the motor operate? Complete. Replace the motor. If the error persists, go to Step 2. 2 Check for +24 V to the Fuser Motor. Is the +24 V across DCHEAT- 3 <=> ground? Go to Step 5. Go to Step 3. 3 Check Motor Driver Board POW24 connector for 24 V. 1. Disconnect POW24. Is the +24 V across POW24 pins 1 and 2? Replace the Motor Driver Board. Go to Step 4. 4 Check for 24 V at the LVPS 1. Disconnect CN2 on the LVPS. Is the +24 V across pins 1 and 2? Replace the POW24 Harness. Replace the LVPS. 5 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 929 |
| Display: | Power Off/on 929: Error |
| Description: | Failure in the Waste Toner Motor The Waste Toner Motor has stopped rotating. Applicable Status Code: Code 929: The Waste Toner Motor has failed. |
| Causes: | • Waste Toner Motor, PL7.1.3 • Motor Driver Board, PL2.1.10 • Engine Control Boar d, PL1.1.4 |
| Remedy: | 1 Test the Waste Toner Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Waste Toner Motor test. Does the motor operate? Complete. Replace the motor. If the error persists, go to Step 2. 2 Check for +24 V to the Waste Toner Motor. Is the +24 V across WTDC- 3 <=> ground? Go to Step 5. Go to Step 3. 3 Check Motor Driver Board POW24 connector for 24 V. 1. Disconnect POW24. Is the +24 V across POW24 pins 1 and 2? Replace the Motor Driver Board. Go to Step 4. 4 Check for 24 V at the LVPS 1. Disconnect CN2 on the LVPS. Is the +24 V across pins 1 and 2? Replace the POW24 Harness. Replace the LVPS. 5 Check all pins of the DRV1 harness for continuity. Disconnect the DRV1 ribbon cable. Is the cable conductive? Replace the Engine Control Board. Replace the DRV1 Harness. |
| Error code: | 981 |
| Display: | Service call 981: Error |
| Description: | <device> |
| Causes: | • Defective NVRAM • Loose connection between the BICU and the NVRAM • Incorrect installation of the NVRAM • Defective BICU |
| Remedy: | The engine protocol violation detected by the specified device. |
| Error code: | 982 |
| Display: | Service call 982: Error |
| Description: | <device> Comm |
| Causes: | • Localization setting not specified (The main power switch is turned on for the first time after the NVRAM is replaced.) • Incorrect localization setting • Defective NVRAM |
| Remedy: | Communications error detected by the specified device. |
