Ricoh CL7000
Рейтинг
Модули
2ND PAPER FEED SECTION
EXTERIOR 2
1ST PAPER FEED SECTION
Frame Section 3
PCU/Development Unit
1st Cassette
Transfer Unit 1
Drive Section 1
FUSING UNIT 2
VERTICAL TRANSPORT SECTION
Transfer Unit 4
Transfer Unit 3
PAPER EXIT SECTION 3
ELECTRICAL SECTION 1
Manual Paper Feed 1
FRAME SECTION 2
Paper Exit Section 5
LASER UNIT
DRIVE SECTION 3
DRIVE SECTION 2
PAPER RESISTRATION
PAPER EXIT SECTION 1
2ND CASSETTE
DRIVE SECTION 4
Color Toner Hopper
PAPER EXIT SECTION 2
Transfer Unit 2
Black Toner Hopper
EXTERIOR 1
Waste Toner Transfer Section
Manual Paper Feed 2
FUSING UNIT 1
Paper Exit Section 4
ELECTRICAL SECTION 2
FRAME SECTION 1
Детали LASER UNIT
| Деталь: | Paper Feed Unit:No.2:Assy |
| Парткод: | G080 2750 |
| Деталь: | Stay - Paper Feed |
| Парткод: | A232 2780 |
| Деталь: | Transport Roller |
| Парткод: | AF02 0404 |
| Деталь: | PICK-UP ROLLER |
| Парткод: | AF03 0049 |
| Деталь: | Gear - 21Z |
| Парткод: | AB01 1188 |
| Деталь: | Retaining Ring C - Separate |
| Парткод: | AA10 0014 |
| Деталь: | FEED ROLLER |
| Парткод: | AF03 1049 |
| Деталь: | Gear - Roller Clutch |
| Парткод: | AB01 1218 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Arm:Pickup |
| Парткод: | G080 2761 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0691 |
| Деталь: | Photointerruptor - Flat |
| Парткод: | AW02 0120 |
| Деталь: | Harness:Paper Feed Unit |
| Парткод: | G080 5483 |
| Деталь: | SHAFT - PAPER FEED |
| Парткод: | AA14 0655 |
| Деталь: | Lever - Feed |
| Парткод: | G065 2767 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2102 |
| Деталь: | Rear Grounding Plate |
| Парткод: | A232 2764 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Release Lever |
| Парткод: | G065 2776 |
| Деталь: | Rear Feed Mylar |
| Парткод: | B004 2782 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 0106 |
| Деталь: | Shaft - Gear |
| Парткод: | AA14 0656 |
| Деталь: | Gear - 23Z |
| Парткод: | AB01 0107 |
| Деталь: | PRESSURE LEVER |
| Парткод: | G065 2774 |
| Деталь: | Stay - Paper Separation |
| Парткод: | G060 2725 |
| Деталь: | Release spring |
| Парткод: | AA06 0908 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0693 |
| Деталь: | LINK LEVER |
| Парткод: | G065 2775 |
| Деталь: | SEPARATION ROLLER |
| Парткод: | AF03 2049 |
| Деталь: | Torque Limiter - 40mn m 18mm |
| Парткод: | G060 2900 |
| Деталь: | Shaft - Separation Driven |
| Парткод: | G060 2689 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | Front Grounding Plate |
| Парткод: | A232 2765 |
| Деталь: | Housing:Paper Feed Unit |
| Парткод: | G060 2760 |
| Деталь: | Feed Mylar |
| Парткод: | A232 2766 |
| Деталь: | Guide Plate:Paper Feed Unit |
| Парткод: | G080 2762 |
| Деталь: | Paper End Feeler |
| Парткод: | A232 2762 |
| Деталь: | Guide Plate:Swivel:Adhesion |
| Парткод: | G060 2630 |
| Деталь: | Upper Filter |
| Парткод: | GA01 2000 |
| Деталь: | Lower Filter |
| Парткод: | GA01 2001 |
| Деталь: | Filter Case |
| Парткод: | G060 1300 |
| Деталь: | Left rear cover |
| Парткод: | G060 1269 |
| Деталь: | Louver - Left Rear Cover |
| Парткод: | G060 1281 |
| Деталь: | Front Cover - Left Lower |
| Парткод: | G060 1271 |
| Деталь: | Bracket - Main Switch |
| Парткод: | G060 5813 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3219 |
| Деталь: | Drum Stay:PCU:Assy |
| Парткод: | G060 2450 |
| Деталь: | Lower Inner Cover |
| Парткод: | G060 1285 |
| Деталь: | Screw - M4X6 |
| Парткод: | G060 2460 |
| Деталь: | Decal - Drum Stay |
| Парткод: | GA00 3025 |
| Деталь: | Cover - Drum Stay |
| Парткод: | G060 2455 |
| Деталь: | Nut - M7 |
| Парткод: | G060 2461 |
| Деталь: | Unit Detection Switch |
| Парткод: | G060 2457 |
| Деталь: | Harness - Unit Detection Switch |
| Парткод: | G060 5489 |
| Деталь: | Spring Plate- Unit Detection Switch |
| Парткод: | G060 2456 |
| Деталь: | Drum Stay |
| Парткод: | G060 2451 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 1011 |
| Деталь: | Inner Cover:Right |
| Парткод: | G080 1282 |
| Деталь: | Inner Cover:Left |
| Парткод: | G080 1284 |
| Деталь: | Left Spring - Drum Stay |
| Парткод: | G060 2481 |
| Деталь: | Inner Cover:Left:Small |
| Парткод: | G080 1295 |
| Деталь: | Right Spring - Drum Stay |
| Парткод: | G060 2482 |
| Деталь: | Front Cover - Right Lower |
| Парткод: | G060 1266 |
| Деталь: | Front right cover |
| Парткод: | G060 1287 |
| Деталь: | Cover:Right:Rear |
| Парткод: | G080 1267 |
| Деталь: | Magnetic Clutch Cover |
| Парткод: | G060 2949 |
| Деталь: | Spring Plate - Clutch Cover |
| Парткод: | G060 2950 |
| Деталь: | Supporting Plate - Right Rear Cover |
| Парткод: | G060 1280 |
| Деталь: | Inner Cover:Toner Cartridge |
| Парткод: | G080 1294 |
| Деталь: | Upper Cover - Exit Tray |
| Парткод: | G077 1275 |
| Деталь: | Exit cover |
| Парткод: | G060 1279 |
| Деталь: | Upper Exit Cover |
| Парткод: | G060 1274 |
| Деталь: | Paper Feed Unit:No.1:Assy |
| Парткод: | G080 2700 |
| Деталь: | Feed Stay |
| Парткод: | G060 2716 |
| Деталь: | PICK-UP ROLLER |
| Парткод: | AF03 0049 |
| Деталь: | Gear - 21Z |
| Парткод: | AB01 1188 |
| Деталь: | Retaining Ring C - Separate |
| Парткод: | AA10 0014 |
| Деталь: | FEED ROLLER |
| Парткод: | AF03 1049 |
| Деталь: | Gear - Roller Clutch |
| Парткод: | AB01 1218 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Arm:Pickup |
| Парткод: | G080 2761 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0691 |
| Деталь: | Photointerruptor - Flat |
| Парткод: | AW02 0120 |
| Деталь: | Harness:Paper Feed Unit |
| Парткод: | G080 5483 |
| Деталь: | SHAFT - PAPER FEED |
| Парткод: | AA14 0655 |
| Деталь: | Lever - Feed |
| Парткод: | G065 2767 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2102 |
| Деталь: | Rear Grounding Plate |
| Парткод: | A232 2764 |
| Деталь: | Snap Ring |
| Парткод: | 52 062 686 |
| Деталь: | Release Lever |
| Парткод: | G065 2776 |
| Деталь: | Rear Feed Mylar |
| Парткод: | G060 2786 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 0106 |
| Деталь: | Shaft - Gear |
| Парткод: | AA14 0656 |
| Деталь: | Gear - 23Z |
| Парткод: | AB01 0107 |
| Деталь: | Release spring |
| Парткод: | AA06 0908 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0693 |
| Деталь: | PRESSURE LEVER |
| Парткод: | G065 2774 |
| Деталь: | LINK LEVER |
| Парткод: | G065 2775 |
| Деталь: | Stay - Paper Separation 1 |
| Парткод: | G060 2727 |
| Деталь: | SEPARATION ROLLER |
| Парткод: | AF03 2049 |
| Деталь: | Torque Limiter - 40mn m 18mm |
| Парткод: | G060 2900 |
| Деталь: | Shaft - Separation Driven |
| Парткод: | G060 2689 |
| Деталь: | Upper Guide - Paper Feed Unit |
| Парткод: | G060 2724 |
| Деталь: | Ground Plate:Front:Paper Feed Unit |
| Парткод: | G080 2763 |
| Деталь: | Housing:Paper Feed Unit |
| Парткод: | G060 2723 |
| Деталь: | Feed Mylar |
| Парткод: | A232 2766 |
| Деталь: | Guide Plate:Paper Feed Unit |
| Парткод: | G080 2762 |
| Деталь: | Paper End Feeler |
| Парткод: | A232 2762 |
| Деталь: | Oil Tank:Collect:Assy |
| Парткод: | G080 4358 |
| Деталь: | Cap - Oil Tank Assembly |
| Парткод: | B051 4361 |
| Деталь: | Decal:Bottle:Fusing |
| Парткод: | G047 4665 |
| Деталь: | Holder:Oil Tank:Assy |
| Парткод: | G080 4359 |
| Деталь: | Holder:Oil Tank:Assy |
| Парткод: | G080 4394 |
| Деталь: | Bracket:Contact Point:Oil Collection Unit:Ass |
| Парткод: | G080 4360 |
| Деталь: | Valve:Oil:Collect:Machine Or Copier:Assy |
| Парткод: | G080 4370 |
| Деталь: | Cam:Contact Point |
| Парткод: | G080 4363 |
| Деталь: | MAGNET CATCH |
| Парткод: | AG07 1011 |
| Деталь: | Bracket:Sensor |
| Парткод: | G080 4380 |
| Деталь: | Harness:Oil:Full |
| Парткод: | G080 5505 |
| Деталь: | Oil End Sensor |
| Парткод: | G024 4740 |
| Деталь: | Photointerruptor:Set Sensor |
| Парткод: | AW02 0136 |
| Деталь: | Bracket:Set Sensor:Oil Tank |
| Парткод: | G080 4384 |
| Деталь: | Heat Cover |
| Парткод: | G080 5815 |
| Деталь: | Decal - High Temperature |
| Парткод: | AA00 0401 |
| Деталь: | Heater - 120V 9W |
| Парткод: | AX40 0109 |
| Деталь: | Heater - 230V 9W |
| Парткод: | AX40 0110 |
| Деталь: | Guide Plate:Transport Unit |
| Парткод: | G080 1082 |
| Деталь: | Supporting Plate:Front Lower |
| Парткод: | G060 1099 |
| Деталь: | PCU - CMY |
| Парткод: | G211 2005 |
| Деталь: | Development Unit:Y:M-PAC:ASSY |
| Парткод: | G219 3003 |
| Деталь: | Development Unit:C:M-PAC:ASSY |
| Парткод: | G219 3001 |
| Деталь: | Development Unit:M:M-PAC:ASSY |
| Парткод: | G219 3002 |
| Деталь: | Paper Tray:No.1:Assy |
| Парткод: | G080 2768 |
| Деталь: | Roller - Paper Tray |
| Парткод: | A232 2987 |
| Деталь: | SHIELD |
| Парткод: | G313 2782 |
| Деталь: | Spring Plate - Paper Tray |
| Парткод: | G060 2775 |
| Деталь: | Bottom Lift Lever |
| Парткод: | A204 2972 |
| Деталь: | Lift shaft |
| Парткод: | G060 2774 |
| Деталь: | Side Fence:Rear:Fix:Adhesion |
| Парткод: | G080 2778 |
| Деталь: | Side Fence:Front:Fix:Adhesion |
| Парткод: | G080 2777 |
| Деталь: | Decal:Paper Tray:No.1 |
| Парткод: | GA00 3066 |
| Деталь: | Tray Bottom Plate:Assy |
| Парткод: | G060 2770 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3006 |
| Деталь: | END FENCE |
| Парткод: | AF01 7023 |
| Деталь: | Shoe:Paper Tray |
| Парткод: | G080 2526 |
| Деталь: | Cleaning Unit:Transfer Belt:Assy |
| Парткод: | G080 3830 |
| Деталь: | Case:Coating Bar |
| Парткод: | G080 3731 |
| Деталь: | Dual Faces Tepe:Entrance Seal |
| Парткод: | G080 3733 |
| Деталь: | Entrance Seal:Cleaning |
| Парткод: | AD04 7034 |
| Деталь: | Shield:Cleaning Unit |
| Парткод: | G080 3732 |
| Деталь: | Brush Roller:Cleaning |
| Парткод: | AD04 2047 |
| Деталь: | Cleaning Blade:Assy |
| Парткод: | AD04 1081 |
| Деталь: | Bracket:Cleaning Blade:Assy |
| Парткод: | G080 3716 |
| Деталь: | Spring:Blade |
| Парткод: | AA06 0920 |
| Деталь: | Transfer Unit:Assy |
| Парткод: | G080 3810 |
| Деталь: | Gear:Brush Roller:Front |
| Парткод: | AB01 1480 |
| Деталь: | Gear:Idler:Cleaning Unit |
| Парткод: | AB01 1481 |
| Деталь: | Gear - Transport Screw |
| Парткод: | G060 3977 |
| Деталь: | Lever:Release:Cleaning Blade |
| Парткод: | G080 3745 |
| Деталь: | Holder:Brush Roller:Front:Assy |
| Парткод: | G080 3740 |
| Деталь: | Casing:Cleaning Unit:Assy |
| Парткод: | G080 3831 |
| Деталь: | Lever:Release |
| Парткод: | G080 3993 |
| Деталь: | Cover:Transfer Unit |
| Парткод: | G080 3994 |
| Деталь: | Drum Stay:Transfer Unit:Peen |
| Парткод: | G080 3990 |
| Деталь: | Stepper Motor:Transfer Belt:Press Fit |
| Парткод: | G080 3980 |
| Деталь: | BUSHING - 6MM |
| Парткод: | AA08 0248 |
| Деталь: | Gear:Drive:Brush Roller:Rear |
| Парткод: | AB01 0130 |
| Деталь: | Toner Collection Coil:Cleaning |
| Парткод: | AD04 3081 |
| Деталь: | Shaft:Toner Collection Coil |
| Парткод: | G060 3952 |
| Деталь: | Sleeve:Shaft:Toner Collection Coil |
| Парткод: | G060 3953 |
| Деталь: | Shutter:Discharge Used Toner |
| Парткод: | G080 3752 |
| Деталь: | Compression Spring:Shutter:Collar |
| Парткод: | AA06 3637 |
| Деталь: | Cap:Discharge Used Toner:Transfer |
| Парткод: | G080 3751 |
| Деталь: | Drive Unit - C/M/Y Development |
| Парткод: | G060 1120 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 0257 |
| Деталь: | Drive Unit - K Development |
| Парткод: | G077 1100 |
| Деталь: | Inner PCU Duct |
| Парткод: | G060 1199 |
| Деталь: | Shielding Plate:Gear:Drum |
| Парткод: | G080 1159 |
| Деталь: | Holder:Positioning Sensor:Gear:Drum |
| Парткод: | G080 1166 |
| Деталь: | Photointerruptor - Flat |
| Парткод: | AW02 0120 |
| Деталь: | Magnetic Clutch Holder |
| Парткод: | G077 1117 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Magnetic Clutch - Development |
| Парткод: | AX20 0244 |
| Деталь: | Joint:Development:Sub-assy |
| Парткод: | G080 1115 |
| Деталь: | Screw:M3 |
| Парткод: | G080 1169 |
| Деталь: | Gear:Drum:Z303:M0.3 |
| Парткод: | AB01 0121 |
| Деталь: | Gear:Drum:Assy |
| Парткод: | G080 1036 |
| Деталь: | Gear:Toner Recycling:Z105-T28 |
| Парткод: | AB01 7633 |
| Деталь: | Gear:Middle:Collar:Z140 |
| Парткод: | AB01 0122 |
| Деталь: | Ground Plate:Opc Drum |
| Парткод: | G080 1168 |
| Деталь: | Bracket:Drum:Drive:Peen |
| Парткод: | G080 1154 |
| Деталь: | DC Motor: DC2.5V 6.5W |
| Парткод: | G080 1162 |
| Деталь: | Stepper Motor:42:Black:Assy |
| Парткод: | G080 1160 |
| Деталь: | Spacer:Mm8.2:1mm |
| Парткод: | AA13 2220 |
| Деталь: | Ball Bearing -20x32x7 |
| Парткод: | AE03 0041 |
| Деталь: | Bracket:Fix:Pressure Roller |
| Парткод: | G060 4179 |
| Деталь: | Gear:Pressure:Drive |
| Парткод: | AB01 2022 |
| Деталь: | PRESSURE ROLLER |
| Парткод: | AE02 0120 |
| Деталь: | Fusing Lamp - 120V 350W |
| Парткод: | AX43 0065 |
| Деталь: | Fusing Lamp - 230V 350W |
| Парткод: | AX43 0070 |
| Деталь: | Thermofuse:Assy |
| Парткод: | G080 4012 |
| Деталь: | Thermistor:Pressure |
| Парткод: | AW10 0083 |
| Деталь: | Shield:Positioning Pin:Front |
| Парткод: | G080 4202 |
| Деталь: | Fusing Entrance Guide Plate |
| Парткод: | G080 4210 |
| Деталь: | Gear:Idler:Drive |
| Парткод: | AB01 2021 |
| Деталь: | Bracket:Gear:Idler |
| Парткод: | G060 4187 |
| Деталь: | Sheet:Fiber:Bracket |
| Парткод: | G060 4188 |
| Деталь: | Shield:Positioning Pin:Rear |
| Парткод: | G080 4203 |
| Деталь: | Bracket:Thermistor |
| Парткод: | G077 4070 |
| Деталь: | Nut:Fusing |
| Парткод: | G060 4190 |
| Деталь: | Bracket:Stud:Rear:Peen |
| Парткод: | G060 4078 |
| Деталь: | Tension Spring - 9.7n |
| Парткод: | GA06 0057 |
| Деталь: | Bracket:Connector |
| Парткод: | G080 4211 |
| Деталь: | Gear:Idler:Pressure:Exit:Z19 |
| Парткод: | AB01 2024 |
| Деталь: | Spacer:Heater |
| Парткод: | G080 4197 |
| Деталь: | Cover - Upper Registration |
| Парткод: | G060 2669 |
| Деталь: | Bracket - Micro Switch |
| Парткод: | G060 2680 |
| Деталь: | Harness:Vertical Transport:Safety Switch |
| Парткод: | G080 5501 |
| Деталь: | Registration Driven Roller |
| Парткод: | G060 2686 |
| Деталь: | Guide:Remove Paper Dust:Assy |
| Парткод: | G077 2839 |
| Деталь: | Guide Plate:Registration:Upper |
| Парткод: | G080 2612 |
| Деталь: | Guide Plate:Registration:Middle |
| Парткод: | G080 2614 |
| Деталь: | Guide Plate:Vertical Transport |
| Парткод: | G080 2643 |
| Деталь: | Spring - Registration |
| Парткод: | G060 2602 |
| Деталь: | Bushing:Registration:Front:Driven |
| Парткод: | G080 2650 |
| Деталь: | Side Plate:Paper Feed:Front:Assy |
| Парткод: | G080 2660 |
| Деталь: | Hook:Vertical Transport:Upper:Peen |
| Парткод: | G080 2670 |
| Деталь: | Torsion Spring - Vertical Transport |
| Парткод: | G060 2674 |
| Деталь: | Hook - Lower Vertical Transport |
| Парткод: | G060 2672 |
| Деталь: | Shaft:Grip |
| Парткод: | G080 2673 |
| Деталь: | Lever - Vertical Transport |
| Парткод: | G060 2690 |
| Деталь: | Cover:Vertical Transport |
| Парткод: | G080 2668 |
| Деталь: | Photointerruptor |
| Парткод: | AW02 0069 |
| Деталь: | Harness:Vertical Transport |
| Парткод: | G080 5506 |
| Деталь: | BUSHING - M4 |
| Парткод: | G060 2652 |
| Деталь: | Spring - 8n |
| Парткод: | AA06 3616 |
| Деталь: | Driven Roller - M3xmm17 |
| Парткод: | AF02 3023 |
| Деталь: | Arm:Roller:Release |
| Парткод: | G080 2645 |
| Деталь: | DC Solenoid:Assy |
| Парткод: | G080 2644 |
| Деталь: | Compression Spring:Driven:2n |
| Парткод: | G080 2656 |
| Деталь: | Driven Roller - M2xmm17 |
| Парткод: | AF02 3022 |
| Деталь: | Side Plate:Paper Feed:Rear:Assy |
| Парткод: | G060 2663 |
| Деталь: | Lower Vertical Transport Hinge |
| Парткод: | G060 2683 |
| Деталь: | Hinge:Vertical Transport |
| Парткод: | G060 2667 |
| Деталь: | Rear Bushing - M6 |
| Парткод: | G060 2651 |
| Деталь: | Ground Plate:Y:Assy |
| Парткод: | G080 3887 |
| Деталь: | Compression Spring:Roller:Back Up |
| Парткод: | AA06 3891 |
| Деталь: | Bushing:Roller:Back Up |
| Парткод: | G080 3862 |
| Деталь: | Roller:Back Up:Assy |
| Парткод: | G080 3898 |
| Деталь: | Compression Spring:Pressure:Transfer Roller |
| Парткод: | AA06 3890 |
| Деталь: | Bushing:Transfer Roller |
| Парткод: | G080 3861 |
| Деталь: | TRANSFER ROLLER |
| Парткод: | G080 3855 |
| Деталь: | Ground Plate:Magenta:Assy |
| Парткод: | G080 3923 |
| Деталь: | Compression Spring - Back Up 3N |
| Парткод: | G060 3924 |
| Деталь: | Bushing - Back-up |
| Парткод: | G060 3852 |
| Деталь: | Roller:Back Up:Assy |
| Парткод: | G080 3864 |
| Деталь: | Terminal:Transfer Roller:Magenta |
| Парткод: | G080 3881 |
| Деталь: | Rear Spring Plate - Transfer |
| Парткод: | G060 3956 |
| Деталь: | Terminal:Earth:Cyan |
| Парткод: | G080 3884 |
| Деталь: | Spring Plate:Ground Plate:Cyan |
| Парткод: | G080 3886 |
| Деталь: | Ground Plate:Connecting:1 |
| Парткод: | G080 3875 |
| Деталь: | Frame:Collar |
| Парткод: | G080 3870 |
| Деталь: | Terminal:Earth:Magenta |
| Парткод: | G080 3883 |
| Деталь: | Ground Plate:Roller:Back Up |
| Парткод: | G080 3880 |
| Деталь: | Front Spring Plate - Transfer |
| Парткод: | G060 3955 |
| Деталь: | Terminal:Transfer Roller:Cyan |
| Парткод: | G080 3882 |
| Деталь: | Harness - High Voltage Line T-K |
| Парткод: | G060 5511 |
| Деталь: | Power Pack:Tpacl:P2 |
| Парткод: | AZ32 0115 |
| Деталь: | Harness:High Voltage Line:T-Y |
| Парткод: | G080 5512 |
| Деталь: | Compression Spring:Earth |
| Парткод: | AA06 3892 |
| Деталь: | Timing Belt:Drive:Transfer Belt |
| Парткод: | AA04 3298 |
| Деталь: | Drive Roller:Assy |
| Парткод: | G080 3910 |
| Деталь: | Shaft:Release:Assy |
| Парткод: | G080 3908 |
| Деталь: | Torsion Spring:Shaft:Release:10N |
| Парткод: | G060 3712 |
| Деталь: | Stay:Left:Assy |
| Парткод: | G080 3904 |
| Деталь: | Shaft:Positioning Pin |
| Парткод: | AA14 0833 |
| Деталь: | Roller:Driven:Left Lower |
| Парткод: | G080 3945 |
| Деталь: | Bracket:Roller:Driven:Peen |
| Парткод: | G080 3946 |
| Деталь: | Shaft:Drive:Brush Roller:Transmission |
| Парткод: | AA14 0834 |
| Деталь: | Roller:Tension |
| Парткод: | G080 3920 |
| Деталь: | Shaft:Positioning Pin:Right |
| Парткод: | AA14 0836 |
| Деталь: | Stay:Right:Assy |
| Парткод: | G080 3900 |
| Деталь: | Roller:Driven:Right Lower |
| Парткод: | G080 3930 |
| Деталь: | Pulley:Tightener |
| Парткод: | AB03 0739 |
| Деталь: | Tightener:Drive:Peen |
| Парткод: | G080 3985 |
| Деталь: | Tension Spring:Tightener |
| Парткод: | AA06 0919 |
| Деталь: | Gear:Drive:Brush Roller:Front |
| Парткод: | AB01 0125 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Tension Spring:Tension:Transfer Belt |
| Парткод: | AA06 0917 |
| Деталь: | Bracket:Roller:Tension:Front |
| Парткод: | G080 3921 |
| Деталь: | Frame:Front:Assy |
| Парткод: | G080 3890 |
| Деталь: | Frame:Rear:Assy |
| Парткод: | G080 3895 |
| Деталь: | Gear:Idler:Brush Roller:Small |
| Парткод: | AB01 0127 |
| Деталь: | Gear:Idler:Brush Roller:Large |
| Парткод: | AB01 0124 |
| Деталь: | Bracket:Roller:Tension:Rear |
| Парткод: | G080 3922 |
| Деталь: | Gear:Drive:Brush Roller:Rear |
| Парткод: | AB01 0130 |
| Деталь: | Harness:Transfer Unit:Drawer |
| Парткод: | G080 5472 |
| Деталь: | Bracket:Drawer |
| Парткод: | G080 3897 |
| Деталь: | Spacer:0.5mm |
| Парткод: | G080 3943 |
| Деталь: | Spacer:M8.2:0.8mm |
| Парткод: | G080 3918 |
| Деталь: | DC Solenoid:Gate Pawl:Exit:Assy |
| Парткод: | G080 4470 |
| Деталь: | Rear Fusing Blacket |
| Парткод: | G060 1091 |
| Деталь: | Decal - Grip B1 |
| Парткод: | GA00 1003 |
| Деталь: | Decal - Vertical Transport |
| Парткод: | GA00 3029 |
| Деталь: | Cover - Fusing Unit Holder |
| Парткод: | G060 6040 |
| Деталь: | Detent Spring |
| Парткод: | G060 6038 |
| Деталь: | Rear Holder Arm |
| Парткод: | G060 6033 |
| Деталь: | Detent Shaft |
| Парткод: | G060 6037 |
| Деталь: | Detent Roller |
| Парткод: | G060 6035 |
| Деталь: | Arm Shaft |
| Парткод: | G060 6036 |
| Деталь: | Bracket - Rear Lever |
| Парткод: | G060 6031 |
| Деталь: | Grip - Cover |
| Парткод: | G060 6039 |
| Деталь: | Bracket - Front Lever |
| Парткод: | G060 6032 |
| Деталь: | Front Holder Arm |
| Парткод: | G060 6034 |
| Деталь: | Holder:Fusing Unit:Peen |
| Парткод: | G080 6021 |
| Деталь: | Decal:Fusing Unit:Positioning Display |
| Парткод: | GA00 3055 |
| Деталь: | Slide Rail:110mm |
| Парткод: | G080 6012 |
| Деталь: | Bracket - Door Switch |
| Парткод: | G060 5823 |
| Деталь: | Bracket - Safety Switch |
| Парткод: | G060 5822 |
| Деталь: | Bracket - Door Switch Lever |
| Парткод: | G060 5801 |
| Деталь: | Bracket:Auxiliary:Peen |
| Парткод: | G080 5805 |
| Деталь: | Lever:Door Switch |
| Парткод: | G080 5807 |
| Деталь: | Arm - Safety Switch |
| Парткод: | G060 5808 |
| Деталь: | Upper Controller Duct |
| Парткод: | G060 1555 |
| Деталь: | Fan Motor - DC1.68W |
| Парткод: | AX64 0123 |
| Деталь: | Lower Controller Duct |
| Парткод: | G077 1556 |
| Деталь: | Duct:Guard:DC Motor |
| Парткод: | G080 1193 |
| Деталь: | Duct - FFC Spacer |
| Парткод: | G077 1195 |
| Деталь: | Duct:Fan:Mm80 |
| Парткод: | G080 1182 |
| Деталь: | Fan Motor - DC2.4W |
| Парткод: | AX64 0103 |
| Деталь: | Duct:Power Supply Unit:Upper Position |
| Парткод: | G077 1560 |
| Деталь: | Guide Plate - Upper Rack |
| Парткод: | G077 5820 |
| Деталь: | Right Upper Rear Guide |
| Парткод: | G060 1192 |
| Деталь: | Power Pack - CB |
| Парткод: | GZ32 0009 |
| Деталь: | Harness:Power Pack:CB |
| Парткод: | G080 5508 |
| Деталь: | Bracket - Power Pack |
| Парткод: | G060 5816 |
| Деталь: | PCB:DRB |
| Парткод: | G080 5130 |
| Деталь: | Bracket:DRB |
| Парткод: | G080 5831 |
| Деталь: | Bracket:Edge Saddle:DRB |
| Парткод: | G080 5833 |
| Деталь: | Cap - PSU |
| Парткод: | G060 5862 |
| Деталь: | Power Supply Unit:J-P2:277W:DOM/NA |
| Парткод: | AZ23 0107 |
| Деталь: | Power Supply Unit 277W:EU/AA/CHN |
| Парткод: | AZ23 0108 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3613 |
| Деталь: | Inner Back Lever - Door Switch |
| Парткод: | G060 5861 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | AA06 3638 |
| Деталь: | Cooling Fan - 24V |
| Парткод: | AX64 0135 |
| Деталь: | Bracket - PSU Fan |
| Парткод: | G060 5863 |
| Деталь: | Harness:AC:Switch |
| Парткод: | G080 5516 |
| Деталь: | Harness:Fusing:Machine Or Copier:AC |
| Парткод: | G080 5513 |
| Деталь: | Plate Nut:M3 |
| Парткод: | G077 1183 |
| Деталь: | Transport Sub-unit:Lengthwise:Assy |
| Парткод: | G080 2531 |
| Деталь: | Front Shaft - Manual Feed Table |
| Парткод: | G060 2973 |
| Деталь: | Rear Shaft - Manual Feed Table |
| Парткод: | G060 2974 |
| Деталь: | Manual Feed Table Assy |
| Парткод: | G060 2856 |
| Деталь: | Front Side Fence |
| Парткод: | G060 2866 |
| Деталь: | Rear Side Fence |
| Парткод: | G060 2867 |
| Деталь: | Pad - Side Fence |
| Парткод: | G060 2908 |
| Деталь: | Decal - Manual Feed |
| Парткод: | GA00 3010 |
| Деталь: | Decal - Inkjet Paper Caution |
| Парткод: | GA00 3038 |
| Деталь: | Paper Guide - Manual Feed Tabl |
| Парткод: | G060 2905 |
| Деталь: | Front Rack |
| Парткод: | A232 6082 |
| Деталь: | Rear Rack |
| Парткод: | A232 6083 |
| Деталь: | Gear - 16T |
| Парткод: | G011 3305 |
| Деталь: | Paper size sensor |
| Парткод: | G060 2869 |
| Деталь: | Cover - Manual Feed Table |
| Парткод: | G060 2865 |
| Деталь: | Torsion Spring:Cover:Left |
| Парткод: | G080 2953 |
| Деталь: | Decal - Vertical Transport 2 |
| Парткод: | GA00 3044 |
| Деталь: | Torsion Spring:Cover:Right |
| Парткод: | G080 2952 |
| Деталь: | Cover - Lower Manual Feed |
| Парткод: | G060 2940 |
| Деталь: | Holder - Used Collection Bottle |
| Парткод: | G060 1079 |
| Деталь: | Toner Bottle Sensor Feeler |
| Парткод: | G060 3627 |
| Деталь: | Shield:Holder:Collection Bottle |
| Парткод: | G060 3629 |
| Деталь: | Used Toner Sensor Spring |
| Парткод: | G060 3626 |
| Деталь: | Stepped Screw - M3 |
| Парткод: | G012 4617 |
| Деталь: | Left Supporter |
| Парткод: | G060 2779 |
| Деталь: | Front Left Supporting Plate |
| Парткод: | G060 1089 |
| Деталь: | Bracket - Front Cover Hinge |
| Парткод: | G060 1277 |
| Деталь: | Shielding Plate - Paper Feed |
| Парткод: | G060 1081 |
| Деталь: | Cap - Positioning |
| Парткод: | B004 2995 |
| Деталь: | Supporter:Right:Assy |
| Парткод: | G060 2780 |
| Деталь: | Upper Positioning Plate |
| Парткод: | G060 2830 |
| Деталь: | Lower Positioning Plate |
| Парткод: | G060 2834 |
| Деталь: | Vertical Transport Hinge |
| Парткод: | G060 1095 |
| Деталь: | Harness:Sensor:On-off |
| Парткод: | G080 5491 |
| Деталь: | Photointerruptor - Flat |
| Парткод: | AW02 0120 |
| Деталь: | Seal - Sensor |
| Парткод: | G060 3998 |
| Деталь: | Bracket:Idler:Fd:Peen |
| Парткод: | G080 4464 |
| Деталь: | Gear:Idler:29Z |
| Парткод: | AB01 2322 |
| Деталь: | Gear:Idler:19Z |
| Парткод: | AB01 2323 |
| Деталь: | Gear - 16Z |
| Парткод: | G060 4458 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Gate Pawl |
| Парткод: | G060 4459 |
| Деталь: | Photointerruptor - Flat |
| Парткод: | AW02 0120 |
| Деталь: | Shaft - Paper Sensor |
| Парткод: | G060 4479 |
| Деталь: | Feeler - Paper Sensor |
| Парткод: | G060 4482 |
| Деталь: | Bracket - Paper Sensor |
| Парткод: | G060 4481 |
| Деталь: | Transport Roller:Floppy Disk |
| Парткод: | AF04 0596 |
| Деталь: | Upper Exit Guide Plate |
| Парткод: | G060 4451 |
| Деталь: | Driven Roller - M16 |
| Парткод: | G060 4447 |
| Деталь: | Drinev Roller - M13 |
| Парткод: | G060 4428 |
| Деталь: | Discharge Brush - Exit |
| Парткод: | AA12 0102 |
| Деталь: | Photointerruptor - Square |
| Парткод: | AW02 0121 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2102 |
| Деталь: | DC Solenoid:Oil Supply:Assy |
| Парткод: | G080 4270 |
| Деталь: | Lever - Gate Pawl |
| Парткод: | G060 4460 |
| Деталь: | Tension Spring - Gate Pawl |
| Парткод: | G060 4461 |
| Деталь: | Heat Sink - DC Solenoid Apply |
| Парткод: | G060 4335 |
| Деталь: | Plate:Grip |
| Парткод: | G080 4237 |
| Деталь: | Imaging Unit |
| Парткод: | G080 1853 |
| Деталь: | Polygon Mirror Motor - DC24W |
| Парткод: | AX06 0212 |
| Деталь: | Positioning Pin |
| Парткод: | G060 1901 |
| Деталь: | Sync Detector Board |
| Парткод: | G060 5322 |
| Деталь: | Thermistor Plate |
| Парткод: | G060 1908 |
| Деталь: | Thermistor - 103AT-4 |
| Парткод: | AW10 0065 |
| Деталь: | Caution Decal |
| Парткод: | AA00 0218 |
| Деталь: | Shield:Cover:Upper |
| Парткод: | G060 1972 |
| Деталь: | Decal - LD 655 |
| Парткод: | AA00 0217 |
| Деталь: | Harness:Imaging Unit |
| Парткод: | G080 5474 |
| Деталь: | Harness:Imaging Unit:Sync Detector:CM |
| Парткод: | G080 5494 |
| Деталь: | LOWER COVER |
| Парткод: | G060 1975 |
| Деталь: | Shield Glass |
| Парткод: | AC01 5035 |
| Деталь: | Harness - FFC K |
| Парткод: | G077 5523 |
| Деталь: | Harness - FFC Y |
| Парткод: | G077 5522 |
| Деталь: | Harness - FFC C |
| Парткод: | G077 5521 |
| Деталь: | Harness - FFC M |
| Парткод: | G077 5520 |
| Деталь: | Stopper:Grip |
| Парткод: | G077 1972 |
| Деталь: | Grip:Imaging Unit |
| Парткод: | G077 1971 |
| Деталь: | Cover:Polygon Scanner:Peen |
| Парткод: | G077 1904 |
| Деталь: | Shield:Cover:Polygon Scanner:1 |
| Парткод: | G077 1906 |
| Деталь: | Shield:Cover:Polygon Scanner:2 |
| Парткод: | G077 1907 |
| Деталь: | Duct:Tray:Exit:Assy |
| Парткод: | G080 1183 |
| Деталь: | Duct:Imaging Unit |
| Парткод: | G077 1042 |
| Деталь: | Rack Holder |
| Парткод: | G060 1087 |
| Деталь: | Relay Bracket |
| Парткод: | G060 1111 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0862 |
| Деталь: | Registration Tightner |
| Парткод: | G060 1106 |
| Деталь: | Spacer - M12x6.2 |
| Парткод: | H072 2236 |
| Деталь: | Registration Timing Pulley |
| Парткод: | AB03 0686 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | Idle Pulley - M15 |
| Парткод: | AB03 0685 |
| Деталь: | Rear Right Channel |
| Парткод: | G060 1085 |
| Деталь: | DC Motor - DC24V 0.5W |
| Парткод: | G060 2800 |
| Деталь: | Clamp - M4.8 |
| Парткод: | G060 5870 |
| Деталь: | Drawer Bracket - Paper Feed Table |
| Парткод: | G060 1053 |
| Деталь: | Rear Left Channel |
| Парткод: | G060 1083 |
| Деталь: | Holder:Guide Pin:Paper Feed Table |
| Парткод: | G060 1054 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Holder - Paper Tray |
| Парткод: | G060 2801 |
| Деталь: | Bracket:Switch:Heater |
| Парткод: | G080 5816 |
| Деталь: | Harness:Dehumidifier |
| Парткод: | G080 5519 |
| Деталь: | Harness:Transfer:Machine Or Copier |
| Парткод: | G080 5497 |
| Деталь: | Holder:OPC Drum:Assy |
| Парткод: | G080 1026 |
| Деталь: | Clamp - M4.8 |
| Парткод: | G060 5870 |
| Деталь: | Clamp - M3.5 |
| Парткод: | G060 5871 |
| Деталь: | DC Motor - 1.56W |
| Парткод: | G060 3706 |
| Деталь: | Timing Belt - S2M370 |
| Парткод: | AA04 3559 |
| Деталь: | Joint:Collection Bottle:Assy |
| Парткод: | G080 3630 |
| Деталь: | Stay:Auxiliary:DRB |
| Парткод: | G080 5832 |
| Деталь: | Link Bracket |
| Парткод: | G060 4855 |
| Деталь: | Snap Ring |
| Парткод: | 54 472 681 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3219 |
| Деталь: | Harness - Density Sensor |
| Парткод: | G060 5530 |
| Деталь: | Bushing:Registration:Front:Mm8 |
| Парткод: | G080 2684 |
| Деталь: | Registration Drive Roller |
| Парткод: | G060 2685 |
| Деталь: | Bushing:Registration:Rear:M8 |
| Парткод: | G080 2680 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Guide Plate:Registration:Lower:Adhesion |
| Парткод: | G080 2605 |
| Деталь: | Photosensor - GP2A28N1 |
| Парткод: | AW01 0048 |
| Деталь: | Harness:Registration Sensor |
| Парткод: | G080 5480 |
| Деталь: | Bracket - Registration Sensor |
| Парткод: | G060 2609 |
| Деталь: | Transport Drive Roller |
| Парткод: | G060 2627 |
| Деталь: | Guide Plate:Duplex:Exit:Upper |
| Парткод: | G080 2621 |
| Деталь: | Photointerrupter - GP2A231LRSA |
| Парткод: | AW01 0098 |
| Деталь: | Harness:Paper Feed Unit:Sensor |
| Парткод: | G080 5482 |
| Деталь: | Bracket:Sensor:Paper Feed |
| Парткод: | G080 2635 |
| Деталь: | Spring - 8n |
| Парткод: | AA06 3408 |
| Деталь: | BUSHING - M4 |
| Парткод: | G060 2652 |
| Деталь: | Driven Roller - M3x16 |
| Парткод: | AF02 2135 |
| Деталь: | Knob - Vertical Transport |
| Парткод: | G060 2681 |
| Деталь: | Transport Drive Roller - Middle |
| Парткод: | G060 2626 |
| Деталь: | Middle Guide Plate |
| Парткод: | G060 2617 |
| Деталь: | Guide Plate:Middle:Lower:Adhesion |
| Парткод: | G060 2618 |
| Деталь: | Bracket - Front Cover Hinge |
| Парткод: | G060 1277 |
| Деталь: | Screw - M3X4 |
| Парткод: | A259 6239 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | Holder:Guide Pin:Paper Feed Table |
| Парткод: | G060 1054 |
| Деталь: | Guide Plate:Duplex:Exit:Lower |
| Парткод: | G080 2622 |
| Деталь: | Guide:Turn |
| Парткод: | G080 2623 |
| Деталь: | Paper Exit Sub-unit:FU:Assy |
| Парткод: | G080 4410 |
| Деталь: | Bracket:Magnet Catch:Rear |
| Парткод: | G080 4457 |
| Деталь: | Magnet Catch:37n |
| Парткод: | AG07 0020 |
| Деталь: | Gear:Exit Roller:Fu:18z |
| Парткод: | G080 4439 |
| Деталь: | BUSHING - M6 |
| Парткод: | AA08 2075 |
| Деталь: | Gear:Idler:21Z |
| Парткод: | G080 4451 |
| Деталь: | Gear:Input:17z:19z |
| Парткод: | G080 4450 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Side Plate:Exit:Rear:Peen |
| Парткод: | G080 4431 |
| Деталь: | Stay:Exit:Upper |
| Парткод: | G080 4436 |
| Деталь: | Guide Plate:Exit:Connecting |
| Парткод: | G080 4440 |
| Деталь: | Compression Spring - Exit Driven 1n |
| Парткод: | G060 4429 |
| Деталь: | BUSHING - M4 |
| Парткод: | G060 4449 |
| Деталь: | Roller:Driven:FU |
| Парткод: | AF04 0593 |
| Деталь: | Transport Roller:Exit:Vertical Transport |
| Парткод: | AF04 0594 |
| Деталь: | Link:Gate Pawl:Exit |
| Парткод: | G080 4441 |
| Деталь: | Torsion Spring:Gate Pawl:Exit |
| Парткод: | G080 4447 |
| Деталь: | Gate Pawl:Exit |
| Парткод: | G080 4442 |
| Деталь: | Exit Roller:FU |
| Парткод: | AF04 0592 |
| Деталь: | Guide Plate:Exit:Entrance:Lower |
| Парткод: | G080 4449 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3716 |
| Деталь: | Stay:Exit:Lower |
| Парткод: | G080 4437 |
| Деталь: | Discharge Brush - Exit |
| Парткод: | AA12 0102 |
| Деталь: | Support Plate - Discharge Brush |
| Парткод: | G060 4496 |
| Деталь: | Cover:Exit |
| Парткод: | G080 4430 |
| Деталь: | Cover:Exit:Lock:Duplex |
| Парткод: | G080 4444 |
| Деталь: | Decal - Grip B2 |
| Парткод: | GA00 1004 |
| Деталь: | Side Plate:Exit:Front |
| Парткод: | G080 4435 |
| Деталь: | Pulley:Exit Roller:20T |
| Парткод: | G080 4438 |
| Деталь: | Timing Belt:S2M186 |
| Парткод: | G080 4445 |
| Деталь: | Bracket:Magnet Catch:Front |
| Парткод: | G080 4456 |
| Деталь: | Driven Roller - M16 |
| Парткод: | G060 4447 |
| Деталь: | Roller:Driven:Connecting |
| Парткод: | AF04 0595 |
| Деталь: | Compression Spring - Exit Driven |
| Парткод: | G060 4436 |
| Деталь: | Roller:Driven:Fusing Exit |
| Парткод: | G080 4452 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Guide Plate:Fusing Exit:Upper |
| Парткод: | G080 4446 |
| Деталь: | Paper Tray:No.2:Assy |
| Парткод: | G080 2772 |
| Деталь: | Decal:Paper Tray:No.2:Right |
| Парткод: | GA00 3068 |
| Деталь: | Gear - 16Z |
| Парткод: | AB01 3868 |
| Деталь: | Bottom Lift Lever |
| Парткод: | A204 2972 |
| Деталь: | Lift shaft |
| Парткод: | G060 2774 |
| Деталь: | Roller - Paper Tray |
| Парткод: | A232 2987 |
| Деталь: | SHIELD |
| Парткод: | G313 2782 |
| Деталь: | Spring Plate - Paper Tray |
| Парткод: | G060 2775 |
| Деталь: | Paper Size Sensor Board |
| Парткод: | G060 2797 |
| Деталь: | Side Fence:Rear:Universal:Assy |
| Парткод: | G080 2782 |
| Деталь: | Side Fence Stopper |
| Парткод: | A267 2859 |
| Деталь: | Rear Lever Stopper |
| Парткод: | A267 2860 |
| Деталь: | Spring Plate - Side Fence |
| Парткод: | A267 2857 |
| Деталь: | Side Fence:Rear:Universal:Adhesion |
| Парткод: | G080 2790 |
| Деталь: | Tension Spring - Paper Size Sensor Board |
| Парткод: | G060 2806 |
| Деталь: | Cover:Paper Size Sensor |
| Парткод: | G077 2798 |
| Деталь: | Tray Bottom Plate:Assy |
| Парткод: | G060 2770 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3006 |
| Деталь: | End Fence - Universal |
| Парткод: | AF01 7024 |
| Деталь: | Side Fence:Front:Universal:Assy |
| Парткод: | G080 2781 |
| Деталь: | STOPPER LEVER |
| Парткод: | A134 2976 |
| Деталь: | Spring Plate |
| Парткод: | A134 2978 |
| Деталь: | Side Fence:Front:Universal:Adhesion |
| Парткод: | G080 2789 |
| Деталь: | Decal:Paper Tray:No.2:Left |
| Парткод: | GA00 3067 |
| Деталь: | Link:Paper Size Sensor Board |
| Парткод: | G077 2796 |
| Деталь: | Gear - Z28/T35 |
| Парткод: | AB01 7641 |
| Деталь: | Timing Belt - 40S3M318 |
| Парткод: | AA04 3561 |
| Деталь: | Snap Ring M6 |
| Парткод: | AA10 0013 |
| Деталь: | Magnetic Clutch - Registration |
| Парткод: | AX20 0220 |
| Деталь: | Timing Pulley - T20 |
| Парткод: | AB03 0690 |
| Деталь: | Gear - Z25/T26 |
| Парткод: | AB01 7543 |
| Деталь: | Gear - Z28/Z21 |
| Парткод: | AB01 7545 |
| Деталь: | Positioning Plate:Shaft:Drive:Manual Feed |
| Парткод: | G080 1161 |
| Деталь: | Bracket:Drive:Manual Feed:Peen |
| Парткод: | G080 1109 |
| Деталь: | Gear - Z15/Z17 |
| Парткод: | AB01 7635 |
| Деталь: | Gear - Z28/Z29 |
| Парткод: | AB01 7540 |
| Деталь: | Gear - Z15 |
| Парткод: | AB01 1241 |
| Деталь: | Gear - Z18/Z29 |
| Парткод: | AB01 7634 |
| Деталь: | Timing Belt - S2M668 |
| Парткод: | AA04 3925 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0863 |
| Деталь: | Tightener - Paper Feed 1 |
| Парткод: | G077 1173 |
| Деталь: | Drive Unit:Stepper Motor:Paper Feed:Assy |
| Парткод: | G080 1170 |
| Деталь: | Gear - 15Z/30Z |
| Парткод: | AB01 7542 |
| Деталь: | Timing Belt - 40S3M162 |
| Парткод: | AA04 3563 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2102 |
| Деталь: | Magnetic Clutch - Paper Feed |
| Парткод: | AX20 0221 |
| Деталь: | Gear - 22Z |
| Парткод: | AB01 4038 |
| Деталь: | Timing Pulley - 20T |
| Парткод: | AB03 0710 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 4037 |
| Деталь: | Bracket - Magnetic Clutch 2 |
| Парткод: | G060 1177 |
| Деталь: | Bracket:Paper Feed:Drive |
| Парткод: | G077 1171 |
| Деталь: | Gear - Z25/T20 |
| Парткод: | AB01 7544 |
| Деталь: | Separation Plate - Paper Feed Drive |
| Парткод: | G060 1169 |
| Деталь: | Bracket - Magnetic Clutch 1 |
| Парткод: | G060 1176 |
| Деталь: | Timing Belt - 40S3M384 |
| Парткод: | AA04 3562 |
| Деталь: | Photointerruptor - Flat |
| Парткод: | AW02 0120 |
| Деталь: | Tightener - Paper Feed |
| Парткод: | G060 1174 |
| Деталь: | Holder:Toner Cartridge:Collar:Assy |
| Парткод: | G080 3201 |
| Деталь: | Tube:Air Pump:BK |
| Парткод: | G080 3215 |
| Деталь: | Tube:Air Pump:Y |
| Парткод: | G080 3240 |
| Деталь: | Tube:Air Pump:MC |
| Парткод: | G080 3214 |
| Деталь: | Tube:Valve:BK |
| Парткод: | G080 3241 |
| Деталь: | Coil - Tube Fuard |
| Парткод: | AA06 3627 |
| Деталь: | Tube - C Toner Supply |
| Парткод: | G060 3238 |
| Деталь: | Guide Coil - M Tube |
| Парткод: | AA06 3656 |
| Деталь: | Tube - M Toner Supply |
| Парткод: | G060 3241 |
| Деталь: | Tube - Y Toner Supply |
| Парткод: | G060 3237 |
| Деталь: | Valve |
| Парткод: | G060 3240 |
| Деталь: | Stepped Screw - M3 |
| Парткод: | G012 4617 |
| Деталь: | Air Pump - Toner Supply |
| Парткод: | G060 3301 |
| Деталь: | Humidity Sensor - RHU-232 |
| Парткод: | AW14 0009 |
| Деталь: | Holder:Toner Cartridge |
| Парткод: | G060 3205 |
| Деталь: | Air Pump:Toner Supply |
| Парткод: | G080 3301 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Holder Seal |
| Парткод: | AA15 3461 |
| Деталь: | Toner Cartridge Holder |
| Парткод: | G060 3219 |
| Деталь: | Compression Spring:4.9n |
| Парткод: | AA06 3663 |
| Деталь: | Nozzle:YMC |
| Парткод: | G080 3216 |
| Деталь: | Optics Sensor:Toner End Sensor |
| Парткод: | AW02 0132 |
| Деталь: | Decal - Y Toner Supply |
| Парткод: | GA00 3016 |
| Деталь: | Decal - C Toner Supply |
| Парткод: | GA00 3018 |
| Деталь: | Decal - M Toner Supply |
| Парткод: | GA00 3017 |
| Деталь: | Toner Cartridge Stopper |
| Парткод: | G060 5599 |
| Деталь: | Base - Toner Cartridge Stopper |
| Парткод: | G060 3232 |
| Деталь: | Holder:Toner Supply Unit |
| Парткод: | G080 1094 |
| Деталь: | Bracket:Option:Rear |
| Парткод: | G080 1099 |
| Деталь: | Guide Plate:Left Upper:Peen |
| Парткод: | G077 5821 |
| Деталь: | Holder:Oil |
| Парткод: | G080 4231 |
| Деталь: | Clip:M11 |
| Парткод: | G080 4233 |
| Деталь: | Tube:Used Develper:Oil |
| Парткод: | G080 4232 |
| Деталь: | Bracket:Drawer:Fusing |
| Парткод: | G080 6041 |
| Деталь: | Supporter:Fusing Unit |
| Парткод: | G080 1078 |
| Деталь: | Photointerruptor - Flat |
| Парткод: | AW02 0120 |
| Деталь: | Cover:Density Sensor |
| Парткод: | G080 3621 |
| Деталь: | Guide Plate:Transfer:Exit |
| Парткод: | G080 3620 |
| Деталь: | Bracket:Density Sensor:Assy |
| Парткод: | G080 3611 |
| Деталь: | Harness:Sensor:TM |
| Парткод: | G080 5495 |
| Деталь: | Tension Spring:Shutter |
| Парткод: | AA06 0921 |
| Деталь: | PCB:Density Sensor |
| Парткод: | G080 5550 |
| Деталь: | Shutter:Density Sensor:Assy |
| Парткод: | G080 3617 |
| Деталь: | Screw - M3X4 |
| Парткод: | A259 6239 |
| Деталь: | Bracket:Option:Front |
| Парткод: | G080 1098 |
| Деталь: | Sheet:Shutter |
| Парткод: | G080 3618 |
| Деталь: | Holder:Connector:Assy |
| Парткод: | G080 1079 |
| Деталь: | Transfer belt |
| Парткод: | G080 3780 |
| Деталь: | Roller:Exit:Press Fit |
| Парткод: | G080 3902 |
| Деталь: | Bushing:Transfer Roller |
| Парткод: | G080 3861 |
| Деталь: | Compression Spring:Pressure:Transfer Roller |
| Парткод: | AA06 3890 |
| Деталь: | TRANSFER ROLLER |
| Парткод: | G080 3855 |
| Деталь: | Bushing - Back-up |
| Парткод: | G060 3852 |
| Деталь: | Compression Spring - Back Up 3N |
| Парткод: | G060 3924 |
| Деталь: | Back Up Roller - Transfer |
| Парткод: | G060 3680 |
| Деталь: | Terminal:Roller:Exit |
| Парткод: | G080 3869 |
| Деталь: | Holder:Frame:BK:Front |
| Парткод: | G080 3867 |
| Деталь: | Ground Plate:Transfer:K |
| Парткод: | G060 3693 |
| Деталь: | Tension Spring - Left Frame |
| Парткод: | G060 3853 |
| Деталь: | Frame:BK |
| Парткод: | G080 3860 |
| Деталь: | Terminal:Transfer Roller:BK |
| Парткод: | G080 3863 |
| Деталь: | Holder:Frame:BK:Rear |
| Парткод: | G080 3868 |
| Деталь: | Bracket:Guide:Left:Assy |
| Парткод: | G080 3951 |
| Деталь: | Spacer:Bracket:ON-OFF |
| Парткод: | AA13 2218 |
| Деталь: | Cam - Front |
| Парткод: | G060 3894 |
| Деталь: | Shaft:On-off |
| Парткод: | G080 3936 |
| Деталь: | Bracket:On-off:Rear:Assy |
| Парткод: | G080 3934 |
| Деталь: | Bushing:On-off |
| Парткод: | AA08 2125 |
| Деталь: | Gear - ON-Off |
| Парткод: | G060 3899 |
| Деталь: | Joint - Front |
| Парткод: | G060 3896 |
| Деталь: | Bracket:On-off:Front:Assy |
| Парткод: | G080 3931 |
| Деталь: | Gear:Roller:Driven |
| Парткод: | AB01 0128 |
| Деталь: | Roller:Roller:Driven:Entrance |
| Парткод: | G080 3942 |
| Деталь: | Roller:Roller:Driven |
| Парткод: | G080 3941 |
| Деталь: | Roller:Driven:Entrance |
| Парткод: | G080 3940 |
| Деталь: | Gear - Bias Roller |
| Парткод: | AB01 0114 |
| Деталь: | Roller:Bias:Assy |
| Парткод: | G080 3965 |
| Деталь: | Cover - Bias Roller |
| Парткод: | G060 3914 |
| Деталь: | Terminal:Bias |
| Парткод: | G080 3967 |
| Деталь: | BUSHING |
| Парткод: | H519 1157 |
| Деталь: | Terminal:Roller:Bias |
| Парткод: | G080 3968 |
| Деталь: | Tension Spring:Pressure:Bias |
| Парткод: | AA06 0931 |
| Деталь: | Guide Plate:Entrance:Transfer |
| Парткод: | G080 3960 |
| Деталь: | Lower Transfer Entrance Guide |
| Парткод: | G060 3677 |
| Деталь: | Upper Registration Guide |
| Парткод: | G060 3908 |
| Деталь: | Bracket:Guide:Right Lower |
| Парткод: | G080 3950 |
| Деталь: | Harness:ID:K |
| Парткод: | G080 5492 |
| Деталь: | Holder:Toner Cartridge:BK:DOM:Assy |
| Парткод: | G080 3202 |
| Деталь: | Holder Seal |
| Парткод: | AA15 3461 |
| Деталь: | Toner Cartridge Holder |
| Парткод: | G060 3219 |
| Деталь: | Compression Spring:4.9n |
| Парткод: | AA06 3663 |
| Деталь: | Nozzle:BK |
| Парткод: | G080 3222 |
| Деталь: | Tube:Valve:BK |
| Парткод: | G080 3241 |
| Деталь: | Optics Sensor:Toner End Sensor |
| Парткод: | AW02 0132 |
| Деталь: | Harness:Toner End Sensor:K |
| Парткод: | G080 5496 |
| Деталь: | Coil - Tube Fuard |
| Парткод: | AA06 3627 |
| Деталь: | Tube - K Toner Supply |
| Парткод: | G060 3236 |
| Деталь: | Decal - K Toner Supply |
| Парткод: | GA00 3019 |
| Деталь: | Toner Cartridge Stopper |
| Парткод: | G060 5599 |
| Деталь: | Base - Toner Cartridge Stopper |
| Парткод: | G060 3232 |
| Деталь: | Decal - Shielding Plate K |
| Парткод: | GA00 3033 |
| Деталь: | Shielding Plate - Y Development |
| Парткод: | G060 3321 |
| Деталь: | Decal - Shielding Plate Y |
| Парткод: | GA00 3030 |
| Деталь: | Shielding Plate - C Development |
| Парткод: | G060 3319 |
| Деталь: | Decal - Shielding Plate C |
| Парткод: | GA00 3032 |
| Деталь: | Shielding Plate - M Development |
| Парткод: | G060 3320 |
| Деталь: | Decal - Shielding Plate M |
| Парткод: | GA00 3031 |
| Деталь: | Duct:PCU:Supporter:Upper |
| Парткод: | G060 1196 |
| Деталь: | PCU Duct |
| Парткод: | G060 1198 |
| Деталь: | Shielding Plate - K Development |
| Парткод: | G060 3318 |
| Деталь: | Toner Cartridge Holder Filter |
| Парткод: | G060 3233 |
| Деталь: | Shield:Holder:Toner Cartridge |
| Парткод: | G060 3337 |
| Деталь: | Holder:Toner Cartridge:Bk:Left |
| Парткод: | G060 3336 |
| Деталь: | Small Cover - Option |
| Парткод: | G060 1289 |
| Деталь: | Lower left cover |
| Парткод: | G060 1220 |
| Деталь: | Inner Cover:Upper |
| Парткод: | G080 1283 |
| Деталь: | Operation Panel - LT |
| Парткод: | G060 7011 |
| Деталь: | Operation Panel - A4 |
| Парткод: | G060 7111 |
| Деталь: | Harness:Operation Sub-unit |
| Парткод: | G080 5484 |
| Деталь: | Harness:Ground Wire:Operation Sub-unit |
| Парткод: | G080 5515 |
| Деталь: | Large Cover - Option |
| Парткод: | G060 1288 |
| Деталь: | Cover:Upper:Rear |
| Парткод: | G080 1272 |
| Деталь: | REAR COVER |
| Парткод: | G077 1268 |
| Деталь: | Sheet - Toner Supply |
| Парткод: | GA00 3009 |
| Деталь: | Decal - Inkjet Paper Caution |
| Парткод: | GA00 3038 |
| Деталь: | Electrode:Ground Plate |
| Парткод: | G080 1319 |
| Деталь: | Seal - C/Y |
| Парткод: | AA15 3462 |
| Деталь: | Band:Stopper:Cover:Right Upper |
| Парткод: | G080 1321 |
| Деталь: | Exit End Fence |
| Парткод: | G060 1293 |
| Деталь: | Cover:Right:Upper |
| Парткод: | G080 1265 |
| Деталь: | Inner Cover:Manual Feed:Assy |
| Парткод: | G080 1224 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Front Stopper Pawl |
| Парткод: | G060 1312 |
| Деталь: | Grip:Cover:Right Upper:Peen |
| Парткод: | G080 1320 |
| Деталь: | Stopper Pawl Shaft |
| Парткод: | G060 1314 |
| Деталь: | Rear Stopper Pawl |
| Парткод: | G060 1313 |
| Деталь: | Rubber Pad - H5 |
| Парткод: | AH01 0009 |
| Деталь: | Cover:Front |
| Парткод: | G077 1262 |
| Деталь: | MAGNET CATCH |
| Парткод: | B024 1264 |
| Деталь: | Sheet:Operate:J-P2 |
| Парткод: | G080 1292 |
| Деталь: | Cleaner - Dust Proof Glass |
| Парткод: | G060 1995 |
| Деталь: | Screw Driver |
| Парткод: | G060 2989 |
| Деталь: | Decal:Emblem:EXP |
| Парткод: | G080 7005 |
| Деталь: | Decal - Emblem (SVN) |
| Парткод: | G080 7505 |
| Деталь: | Decal - Emblem (GES NA) |
| Парткод: | G080 7506 |
| Деталь: | Decal - Emblem (NRG NAS) |
| Парткод: | G080 7605 |
| Деталь: | Decal - Emblem (NRG REX) |
| Парткод: | G080 7606 |
| Деталь: | Decal - Emblem (NRG GES) |
| Парткод: | G080 7607 |
| Деталь: | Decal - Emblem (INF) |
| Парткод: | G080 7705 |
| Деталь: | Decal - Emblem (LAN EU) |
| Парткод: | G080 7905 |
| Деталь: | Hinge - Front Cover |
| Парткод: | G020 1332 |
| Деталь: | Decal - Energystar |
| Парткод: | GA00 3034 |
| Деталь: | EXIT TRAY |
| Парткод: | G060 4491 |
| Деталь: | EXIT TRAY |
| Парткод: | G060 4490 |
| Деталь: | Sub Exit Tray |
| Парткод: | G060 4492 |
| Деталь: | Supporter:PCU |
| Парткод: | G080 1072 |
| Деталь: | Film - PCU Guide Rail |
| Парткод: | G060 1184 |
| Деталь: | Supporter:PCU:Peen |
| Парткод: | G080 1071 |
| Деталь: | Tube:Connecting:Bk |
| Парткод: | B101 3561 |
| Деталь: | Guide:Collection Bottle:Assy |
| Парткод: | G080 3603 |
| Деталь: | Toner Outlet Sub-unit:CY:Sub-assy |
| Парткод: | G080 3361 |
| Деталь: | Toner Outlet Sub-unit:M:Sub-assy |
| Парткод: | G080 3363 |
| Деталь: | Seal - Case M/Y |
| Парткод: | AA15 3463 |
| Деталь: | Case:Connecting:BK |
| Парткод: | B101 3560 |
| Деталь: | Pump:Toner Supply Unit:BK:Sub-assy |
| Парткод: | G080 3351 |
| Деталь: | Pump:Toner Supply Unit:Y:Sub-assy |
| Парткод: | G080 3354 |
| Деталь: | Pump:Toner Supply Unit:C:Sub-assy |
| Парткод: | G080 3353 |
| Деталь: | Pump:Toner Supply Unit:M:Sub-assy |
| Парткод: | G080 3352 |
| Деталь: | Left Guide - Development Unit |
| Парткод: | G060 1076 |
| Деталь: | Safety Switch Feeler |
| Парткод: | G060 2972 |
| Деталь: | Upper Registration Stay |
| Парткод: | G060 1074 |
| Деталь: | Toner Outlet Sub-unit:BK:Sub-assy |
| Парткод: | B101 3360 |
| Деталь: | Cover:Connecting:Bk:Assy |
| Парткод: | B101 3562 |
| Деталь: | Retaining Ring C - Separate |
| Парткод: | AA10 0014 |
| Деталь: | Feed Roller - Manual Feed |
| Парткод: | AF03 1046 |
| Деталь: | Separation Roller - Manual Feed |
| Парткод: | AF03 2046 |
| Деталь: | TORQUE LIMITER |
| Парткод: | G080 2900 |
| Деталь: | Manual Feed Unit:Assy |
| Парткод: | G080 2851 |
| Деталь: | Housing Cover |
| Парткод: | G060 2930 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Shaft:Feed |
| Парткод: | G080 2683 |
| Деталь: | Stopper Plate |
| Парткод: | G060 2914 |
| Деталь: | Gear - 23Z |
| Парткод: | AB01 1387 |
| Деталь: | PICK-UP ROLLER |
| Парткод: | AF03 0049 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3568 |
| Деталь: | Pick-up Arm - Manual Feed |
| Парткод: | G060 2932 |
| Деталь: | DC Solenoid - Pick-up |
| Парткод: | G060 2937 |
| Деталь: | Harness:Manual Feed Unit |
| Парткод: | G080 5481 |
| Деталь: | Gear - 27Z |
| Парткод: | AB01 1418 |
| Деталь: | Magnetic Clutch - 245mn m |
| Парткод: | AX20 0134 |
| Деталь: | Drive Support Plate |
| Парткод: | A166 2849 |
| Деталь: | Link:Pressure Release:Registration |
| Парткод: | G080 2651 |
| Деталь: | Bracket:Link:Assy |
| Парткод: | G080 2652 |
| Деталь: | Slider:Registration:Release |
| Парткод: | G080 2649 |
| Деталь: | Stepped Screw - M3 |
| Парткод: | AA14 3025 |
| Деталь: | Grounding Plate - Reverse |
| Парткод: | G060 2948 |
| Деталь: | Feeler - Paper End |
| Парткод: | G060 2931 |
| Деталь: | Feeler Roller |
| Парткод: | A134 2661 |
| Деталь: | Photointerruptor - Flat |
| Парткод: | AW02 0120 |
| Деталь: | Housing:Manual Feed |
| Парткод: | G060 2928 |
| Деталь: | Feed guide |
| Парткод: | G060 2982 |
| Деталь: | Decal - Vertical Transport 2 |
| Парткод: | GA00 3044 |
| Деталь: | Guide Plate - Separator |
| Парткод: | G060 2874 |
| Деталь: | Bottom Plate Pad |
| Парткод: | AF01 3016 |
| Деталь: | Bushing:Feed |
| Парткод: | G080 2682 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3499 |
| Деталь: | Separation Driven Shaft |
| Парткод: | G060 2871 |
| Деталь: | Gear - Separation Driven |
| Парткод: | AB01 1417 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 1416 |
| Деталь: | Shaft:Separator:Drive |
| Парткод: | AA14 0728 |
| Деталь: | Grip:Fusing Unit |
| Парткод: | G080 4317 |
| Деталь: | Tension Spring:Grip |
| Парткод: | G080 4308 |
| Деталь: | Sheet:Fiber:Grip |
| Парткод: | G080 4323 |
| Деталь: | Supporter:Oil Application Unit:Rear |
| Парткод: | G080 4315 |
| Деталь: | Gear:Oil Supply Roller:No.2 |
| Парткод: | G080 4192 |
| Деталь: | Stay:Fusing:Upper:Assy |
| Парткод: | G080 4035 |
| Деталь: | Spring Plate:Return |
| Парткод: | G080 4307 |
| Деталь: | Supporter:Oil Application Unit:Front |
| Парткод: | G080 4309 |
| Деталь: | Gear:Oil Supply Roller:No.1 |
| Парткод: | G080 4194 |
| Деталь: | Gear:Oil Supply Roller:No.2:Front |
| Парткод: | G080 4195 |
| Деталь: | Fusing Belt |
| Парткод: | G060 4208 |
| Деталь: | Heater:120V:700W |
| Парткод: | AX44 0169 |
| Деталь: | Heater:230V:700W |
| Парткод: | AX44 0176 |
| Деталь: | Stay:Heat Roller:Assy |
| Парткод: | G080 4042 |
| Деталь: | Thermostat:Assy |
| Парткод: | G080 4152 |
| Деталь: | Thermistor:Fusing |
| Парткод: | AW10 0077 |
| Деталь: | Gear:Fusing |
| Парткод: | AB01 2023 |
| Деталь: | Ball Bearing - 10x22x6 |
| Парткод: | AE03 0044 |
| Деталь: | Hot Roller:Mm29 |
| Парткод: | AE01 0037 |
| Деталь: | Knob:Fusing |
| Парткод: | G080 4251 |
| Деталь: | Guide Plate:Fusing Exit:Lower:Assy |
| Парткод: | G080 4010 |
| Деталь: | Spring:Pickoff Pawl:Pressure Roller |
| Парткод: | AA06 6594 |
| Деталь: | Stripper Pawl |
| Парткод: | AE04 4050 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | AA14 3520 |
| Деталь: | Bracket:Pickoff Pawl:Assy |
| Парткод: | G080 4180 |
| Деталь: | Pickoff Pawl:Belt:Fusing |
| Парткод: | AE04 4051 |
| Деталь: | Tension Spring:Stripper Pawls |
| Парткод: | AA06 0932 |
| Деталь: | Spring:Pressure:Hot Roller |
| Парткод: | G080 4126 |
| Деталь: | Arm:Hot Roller:Rear |
| Парткод: | G080 4129 |
| Деталь: | Arm:Hot Roller:Front |
| Парткод: | G080 4128 |
| Деталь: | Magnet Catch:Fusing |
| Парткод: | G080 4245 |
| Деталь: | Fusing Cover:Upper:Exp:Assy |
| Парткод: | G080 4207 |
| Деталь: | Nut:Fusing |
| Парткод: | G060 4190 |
| Деталь: | Spacer:Heater |
| Парткод: | G080 4197 |
| Деталь: | Stopper Shaft Bracket |
| Парткод: | G060 4850 |
| Деталь: | Bracket:Gear:Floppy Disk:Peen |
| Парткод: | G077 4464 |
| Деталь: | Gear:Pulley:18Z27T |
| Парткод: | G077 4462 |
| Деталь: | Side Plate:Exit:FD:Rear |
| Парткод: | G080 4461 |
| Деталь: | Gear:Pulley:25Z:30T |
| Парткод: | AB01 2321 |
| Деталь: | Timing Belt - S2M176 |
| Парткод: | G060 4463 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Guide Plate:Exit:Lower |
| Парткод: | G060 4455 |
| Деталь: | Driven Roller - M13 |
| Парткод: | G060 4454 |
| Деталь: | ROLLER HOLDER |
| Парткод: | G060 4467 |
| Деталь: | Exit Roller:Floppy Disk |
| Парткод: | AF04 0597 |
| Деталь: | Bracket - Exit Roller |
| Парткод: | G060 4457 |
| Деталь: | Stay:Exit:Floppy Disk:Lower |
| Парткод: | G080 4462 |
| Деталь: | Side Plate:Exit:FD:Front |
| Парткод: | G080 4460 |
| Деталь: | Base:Set Sensor |
| Парткод: | G080 4291 |
| Деталь: | Electrode:Set Sensor:Machine Or Copier |
| Парткод: | G080 4292 |
| Деталь: | Harness:New Article Sensor:Oil |
| Парткод: | G080 5504 |
| Деталь: | Stay:Exit:FD:Upper |
| Парткод: | G080 4463 |
| Деталь: | Frame:Lengthwise Upper:Peen |
| Парткод: | G080 1066 |
| Деталь: | Holder:Guide:Roller |
| Парткод: | G080 4097 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3716 |
| Деталь: | Paper Separation Guide |
| Парткод: | A267 3255 |
| Деталь: | Shaft:Guide |
| Парткод: | G060 4098 |
| Деталь: | Holder:Guide:Rear |
| Парткод: | G060 4096 |
| Деталь: | Holder:Guide:Front |
| Парткод: | G060 4095 |
| Деталь: | Supporting Plate:Set Sensor |
| Парткод: | G080 4293 |
| Деталь: | Upper Spring Plate - Rack |
| Парткод: | G060 5829 |
| Деталь: | Application Rack Assy |
| Парткод: | G077 5841 |
| Деталь: | Bracket - Harness |
| Парткод: | G077 5848 |
| Деталь: | Left rear cover |
| Парткод: | G060 5849 |
| Деталь: | Harness:Main:Middle |
| Парткод: | G080 5451 |
| Деталь: | Panel:Control Board |
| Парткод: | G080 5852 |
| Деталь: | Panel Cover - Option |
| Парткод: | G060 5854 |
| Деталь: | Grip - Application |
| Парткод: | G060 5853 |
| Деталь: | Flanged Hexagonal Head Bolt - M3x6 |
| Парткод: | G034 2993 |
| Деталь: | Harness:Fusing:Machine Or Copier:Dc |
| Парткод: | G080 5455 |
| Деталь: | PCB:J-P2:ROMDIMM:EXP:Assy |
| Парткод: | G080 6120 |
| Деталь: | PCB:CTL:J-P2 |
| Парткод: | G080 5700 |
| Деталь: | Rack - Inner Back Application |
| Парткод: | G060 5847 |
| Деталь: | Bracket - Controller Board |
| Парткод: | G060 5856 |
| Деталь: | Cover:Duct:Fan:Assy |
| Парткод: | G077 1193 |
| Деталь: | Harness:Power Supply Unit |
| Парткод: | G080 5454 |
| Деталь: | Harness:DRB |
| Парткод: | G080 5457 |
| Деталь: | PCB:J-BCU:P2:Service |
| Парткод: | G080 5053 |
| Деталь: | Harness:Main:Lower |
| Парткод: | G080 5450 |
| Деталь: | Harness:Main:Left |
| Парткод: | G080 5456 |
| Деталь: | Gasket:Rack:Front |
| Парткод: | G080 5844 |
| Деталь: | Shadeing Plate:Cover:Duct:Peen |
| Парткод: | G080 1195 |
| Деталь: | Total Counter-RAM-STK12C68-P55 |
| Парткод: | G060 9099 |
| Деталь: | Guide Plate:Operation Panel |
| Парткод: | G080 1460 |
| Деталь: | Relay Guide Plate |
| Парткод: | G060 4820 |
| Деталь: | FFC Harness Plate |
| Парткод: | G060 5899 |
| Деталь: | FCC Harness Cushion |
| Парткод: | G060 5898 |
| Деталь: | Slide Rail:Left:Assy |
| Парткод: | AA07 1009 |
| Деталь: | Left Guide Plate - Imaging Uni |
| Парткод: | G060 1068 |
| Деталь: | Collection Bottle Bracket |
| Парткод: | G060 3623 |
| Деталь: | Photointerruptor - Square |
| Парткод: | AW02 0121 |
| Деталь: | Harness:Set Sensor:Bottle |
| Парткод: | G080 5493 |
| Деталь: | Set Sensor - Collection Bottle |
| Парткод: | AW50 0025 |
| Деталь: | Slide Rail:Right:Assy |
| Парткод: | AA07 1010 |
| Деталь: | Right Guide Plate - Imaging Unit |
| Парткод: | G060 1070 |
| Деталь: | Duplex Left Bracket |
| Парткод: | G060 4860 |
| Деталь: | Duplex Right Bracket |
| Парткод: | G060 4865 |
Коды ошибок
SC 101
SC 120
SC 121
SC 122
SC 142
SC 161
SC 195
SC 201
SC 220
SC 221
SC 230
SC 231
SC 240
SC 260
SC 261
SC 285
SC 370
SC 371
SC 372
SC 373
SC 374
SC 375
SC 376
SC 377
SC 380
SC 381
SC 385
SC 386
SC 387
SC 388
SC 389
SC 390
SC 391-01
SC 392-001
SC 440-001
SC 460-001
SC 460-002
SC 461-001
SC 461-002
SC 471
SC 490
SC 501
SC 502
SC 503-01
SC 503-02
SC 504-01
SC 504-02
SC 530
SC 541
SC 542
SC 543
SC 544
SC 545
SC 546
SC 551
SC 552
SC 553
SC 554
SC 555
SC 556
SC 560
SC 620
SC 621
SC 622
SC 623
SC 640
SC 641
SC 642
SC 670
SC 672
SC 680
SC 685
SC 686
SC 687
SC 690-001
SC 691
SC 700
SC 701
SC 722
SC 724
SC 725
SC 726
SC 727
SC 729
SC 730
SC 731
SC 732
SC 733
SC 734
SC 804
SC 805
SC 806
SC 807
SC 808
SC 809
SC 810
SC 818
SC 819
SC820
SC 821
SC822
SC 823
SC 824
SC 826
SC 827
SC 828
SC829
SC 833
SC 835
SC 836
SC 837
SC 850
SC 851
SC 853
SC 854
SC 855
SC 856
SC 857
SC 860
SC 861
SC 863
SC 864
SC 865
SC 900
SC 990
SC 997
SC 998
SC 999
Описание
| Error code: | SC 101 |
| Description: | Exposure lamp error • The standard white level is not properly detected when scanning the shading plate. (The shading data peak does not reach the specified threshold.) |
| Causes: | • Exposure lamp defective • Lamp stabilizer defective • Exposure lamp connector defective • Standard white plate dirty • Scanner mirror or scanner lens out of position or dirty • SBU defective |
| Remedy: | 1. Turn the main switch off and on. 2. Turn the power key off and on. 3. Check and clean the scanner mirror(s) and scanner lens. 4. Check and clean the shading plate. 5. Replace the exposure lamp. 6. Replace the lamp stabilizer. 7. Replace the scanner mirror(s) or scanner lens. 8. Replace the SBU. |
| Error code: | SC 120 |
| Description: | Scanner home position error 1 • The scanner home position sensor does not detect the on condition during scanning. |
| Causes: | • Scanner PSU or SBU defective • Scanner motor defective • Harness between scanner PSU and scanner motor disconnected • Scanner HP sensor defective • Harness between SBU and HP sensor disconnected • Scanner wire, timing belt, pulley, or carriage defective |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection between the scanner PSU and scanner motor. 3. Check the cable connection between the SBU and HP sensor. 4. Replace the SBU or scanner PSU. 5. Replace the scanner motor. 6. Replace the HP sensor. 7. Replace the scanner wire, timing belt, pulley, or carriage. |
| Error code: | SC 121 |
| Description: | Scanner home position error 2 • The scanner home position sensor does not detect the off condition during scanning. |
| Causes: | • Scanner PSU or SBU defective • Scanner motor defective • Harness between scanner PSU and scanner motor disconnected • Scanner HP sensor defective • Harness between SBU and HP sensor disconnected • Scanner wire, timing belt, pulley, or carriage defective |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection between the scanner PSU and scanner motor. 3. Check the cable connection between the SBU and HP sensor. 4. Replace the SBU or scanner PSU. 5. Replace the scanner motor. 6. Replace the HP sensor. 7. Replace the scanner wire, timing belt, pulley, or carriage. |
| Error code: | SC 122 |
| Description: | Scanner home position error 3 • The scanner home position sensor does not detect the home position during initialization. |
| Causes: | • Scanner PSU or SBU defective • Scanner motor defective • Harness between scanner PSU and scanner motor disconnected • Scanner HP sensor defective • Harness between SBU and HP sensor disconnected • Scanner wire, timing belt, pulley, or carriage defective |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection between the scanner PSU and scanner motor. 3. Check the cable connection between the SBU and HP sensor. 4. Replace the SBU or scanner PSU. 5. Replace the scanner motor. 6. Replace the HP sensor. 7. Replace the scanner wire, timing belt, pulley, or carriage. |
| Error code: | SC 142 |
| Description: | White level detection error • The white level cannot be adjusted within the target during auto gain control. |
| Causes: | • Dirty exposure glass or optics section • SBU board defective • IPU board defective • Exposure lamp defective • Lamp stabilizer defective |
| Remedy: | 1. Turn on the main switch off and on. 2. Clean the exposure glass, white plate, mirrors, and lens. 3. Check if the exposure lamp is lit during initialization. 4. Check the harness connection between SBU and IPU. 5. Replace the exposure lamp. 6. Replace the SBU board. 7. Replace the IPU board |
| Error code: | SC 161 |
| Description: | IDU error • After the command is written into the DFID selfdiagnosis startup register, the correct value is not stored in the register in the specified duration. NOTE: This error is detected when the main switch is turned on. • After the negate interruption of FGATE occurs, IDU is not recognized in the specified duration. NOTE: This error is detected during scanning operations. |
| Causes: | • IPU board defective (defective connection between ASIC and DFID, or Defective LSYNC) |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the IPU board. |
| Error code: | SC 195 |
| Description: | Serial Number Mismatch • Serial number stored in the memory does not consist of the correct code. |
| Causes: | • NVRAM defective • BCU replaced without original NVRAM |
| Remedy: | Open the front cover and turn on the main switch. Check the serial number with SP5-811-002. If the stored serial number is incorrect, contact your product specialist for details of how to solve the problem. |
| Error code: | SC 201 |
| Description: | Polygon motor error • The polygon mirror motor does not reach the targeted operating speed within 15 seconds after turning on. • The lock signal does not become high within 15 seconds after turning off the polygon motor. • The lock signal does not become low within 0.2 second after the polygon motor reaches the targeted operating speed. |
| Causes: | • Polygon mirror motor error • Abnormal GAVD behavior • Cable disconnection |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cables. 3. Replace the polygon motor. |
| Error code: | SC 220 |
| Description: | Synch. detection signal error 1 220-001: Y 220-002: M 220-003: C 220-004: K0 220-005: K1 The front (for K&Y) or rear (for C&M) laser synchronizing detector board, which is used to determine the start timing of laser writing, does not send a signal while the polygon motor is operating normally and the LD is on. |
| Causes: | • Disconnection of the cable between front (K&Y) or rear (C&M) synchronizing detector board and the LD unit • Incorrect installation of front (K&Y) or rear (C&M) synchronizing detector board (the beam does not target the photo detector.) • Defective LD unit • Defective BCU • Defective +5VLD circuit |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection between front (for K&Y) or rear (for C&M) synchronizing detector board and the LD unit. 3. Check or reinstall the front (for K&Y) or rear (for C&M) synchronizing detector board. 4. Replace the front (for K&Y) or rear (for C&M) synchronizing detector board. 5. Replace the laser optics housing unit. 6. Replace the BCU. 7. Replace the PSU. |
| Error code: | SC 221 |
| Description: | Synch. detection signal error 2 221-001: Y 221-002: M 221-003: C 221-004: K Main scan length detection is not properly completed ten consecutive times. The front (for C&M) or rear (for K&Y) laser synchronizing detector boards are used for the main scan length detection, which automatically corrects the main-scan magnification. |
| Causes: | • Damaged or disconnected cable between front (C&M) or rear (K&Y) laser synchronizing detector board and the LD unit • Incorrect installation of front (C&M) or rear (K&Y) synchronizing detector board (the beam does not target the photo detector.) • Defective front (C&M) or rear (K&Y) synchronizing detector board • Defective LD unit |
| Remedy: | After doing any of the following, print ten jobs or more to see if the same SC code is displayed: 1. Turn the main switch off and on. 2. Check or replace the cable connecting front (for C&M) or rear (for K&Y) synchronizing detector board and the LD unit. 3. Check or reinstall the front (for C&M) or rear (for K&Y) synchronizing detector board. 4. Replace the front (for C&M) or rear (for K&Y) synchronizing detector board. 5. Replace the laser optics housing unit. 6. Replace the BCU. If a synch. detector board cannot be replaced, do the following as a temporary measure: • Disable main scan length detection (SP 2-919-001) |
| Error code: | SC 230 |
| Description: | FGATE error 230-001: Y 230-002: M 230-003: C 230-004: K The BCU generates the FGATE signal based on the registration sensor ON timing. Then, it sends the signal to the LD units. The LD units send a feedback signal to the BCU. When the LD units start emitting laser beams, the feedback signal changes from High to Low. The SC code is generated when the BCU receives no feedback signal (stays High) from the LD unit 1 second after paper reaches the position where the laser should start writing. |
| Causes: | • Poor connection between BCU and LD units • Defective BCU • Defective LD unit |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cables between the LD units and the BCU. 3. Replace the laser optics housing unit. 4. Replace the BCU. |
| Error code: | SC 231 |
| Description: | FGATE timeout 231-001: Y 231-002: M 231-003: C 231-004: K When LD units emit laser beams to print a job, the feedback signal stays Low and becomes High after laser exposure for a page is completed. The SC code is detected in the following cases: • When the feedback signal stays Low 7 seconds after completing the laser exposure, or • When the feedback signal stays Low until the laser exposure timing for the next page in multi-page print mode. |
| Causes: | • Poor connection between BCU and LD units • Defective BCU • Defective LD unit |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cables between the LD units and the BCU. 3. Replace the laser optics housing unit. 4. Replace the BCU. |
| Error code: | SC 240 |
| Description: | LD over 240-001: Y 240-002: M 240-003: C 240-004: K The power supply for the LD unit exceeds 67 mA. |
| Causes: | • LD worn out (current/light output characteristics have changed.) • LD broken (short circuit) |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the laser optics housing unit. |
| Error code: | SC 260 |
| Description: | LD HP sensor not switched on (for K only) During homing, it takes more than five seconds to switch the HP sensor on (the sensor actuator does not cover the sensor). |
| Causes: | • Defective motor • Defective sensor • Mechanical problem when switching the actuator • Brown fuse (FU81) on the Power supply unit |
| Remedy: | 1. Turn the main switch off and on. 2. Check the sensor actuator position of the LD positioning motor. 3. Replace the LD positioning motor. 4. Replace the LD home position sensor. 5. Check and/or replace the PSU. |
| Error code: | SC 261 |
| Description: | LD HP sensor not switched off (for K only) After the laser beam pitch was changed, it takes more than five seconds for the HP sensor to switch off. |
| Causes: | • Defective motor • Defective sensor • Mechanical problem when switching the actuator • Brown fuse (FU81) on the Power supply unit |
| Remedy: | 1. Turn the main switch off and on. 2. Check the sensor actuator position of the LD positioning motor. 3. Replace the LD positioning motor. 4. Replace the LD home position sensor. 5. Check and/or replace the PSU. |
| Error code: | SC 285 |
| Description: | Line position adjustment (MUSIC) error Line position adjustment fails three consecutive times. |
| Causes: | • Pattern sampling error due to insufficient image density of patterns used for the adjustment • Inconsistency in the sampling line position adjustment pattern due to dust on the pattern, damage to the OPC drum, damage or toner dropped on the transfer belt, or a dirty or defective ID sensor |
| Remedy: | 1. Turn the main switch off and on. 2. Check and fix the problem that causes low image density. . 3. Clean or replace the transfer belt and/or the ID sensor. 4. Replace the PCU or clean the development unit that causes toner to drop on the transfer belt. |
| Error code: | SC 370 |
| Description: | TD sensor [K]: Adjustment error During the developer initialization, the output value of the TD sensor is without the adjustment range (3.0 ± 0.1V). |
| Causes: | • Poor connection (TD sensor outputs is less than 0.5V.) • Defective TD sensor |
| Remedy: | 1. Turn the main switch off and on. 2. Reset the related color development unit. 3. Replace the related color development unit. |
| Error code: | SC 371 |
| Description: | TD sensor [Y]: Adjustment error During the developer initialization, the output value of the TD sensor is without the adjustment range (3.0 ± 0.1V). |
| Causes: | • Poor connection (TD sensor outputs is less than 0.5V.) • Defective TD sensor |
| Remedy: | 1. Turn the main switch off and on. 2. Reset the related color development unit. 3. Replace the related color development unit. |
| Error code: | SC 372 |
| Description: | TD sensor [C]: Adjustment erro rDuring the developer initialization, the output value of the TD sensor is without the adjustment range (3.0 ± 0.1V). |
| Causes: | • Poor connection (TD sensor outputs is less than 0.5V.) • Defective TD sensor |
| Remedy: | 1. Turn the main switch off and on. 2. Reset the related color development unit. 3. Replace the related color development unit. |
| Error code: | SC 373 |
| Description: | TD sensor [M] : Adjustment error During the developer initialization, the output value of the TD sensor is without the adjustment range (3.0 ± 0.1V). |
| Causes: | • Poor connection (TD sensor outputs is less than 0.5V.) • Defective TD sensor |
| Remedy: | 1. Turn the main switch off and on. 2. Reset the related color development unit. 3. Replace the related color development unit. |
| Error code: | SC 374 |
| Description: | Vt error [K] During the image development, Vt value is less than 0.5V. |
| Causes: | • Poor connection (TD sensor outputs is less than 0.5V.) • Defective TD sensor |
| Remedy: | 1. Turn the main switch off and on. 2. Reset the related color development unit. 3. Replace the related color development unit. |
| Error code: | SC 375 |
| Description: | Vt error [Y ]During the image development, Vt value is less than 0.5V. |
| Causes: | • Poor connection (TD sensor outputs is less than 0.5V.) • Defective TD sensor |
| Remedy: | 1. Turn the main switch off and on. 2. Reset the related color development unit. 3. Replace the related color development unit. |
| Error code: | SC 376 |
| Description: | Vt error [C] During the image development, Vt value is less than 0.5V. |
| Causes: | • Poor connection (TD sensor outputs is less than 0.5V.) • Defective TD sensor |
| Remedy: | 1. Turn the main switch off and on. 2. Reset the related color development unit. 3. Replace the related color development unit. |
| Error code: | SC 377 |
| Description: | Vt error [M] During the image development, Vt value is less than 0.5V. |
| Causes: | • Poor connection (TD sensor outputs is less than 0.5V.) • Defective TD sensor |
| Remedy: | 1. Turn the main switch off and on. 2. Reset the related color development unit. 3. Replace the related color development unit. |
| Error code: | SC 380 |
| Description: | Black development motor error When the motor speed is within the target level, the motor sends a lock signal (High to Low at CN214-5) to the BCU. SC380 is detected under the following conditions: • The Lock signal stays High 2 seconds after the motor turns on. • The Lock signal stays Low 2 seconds after the motor turns off. • The Lock signal stays High for more than 2 seconds while the motor is on. |
| Causes: | • Defective motor • Defective BCU |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the motor. 3. Replace the BCU. |
| Error code: | SC 381 |
| Description: | Color development motor error When the motor speed is within the target level, the motor sends a lock signal (High to Low at CN214-5) to the BCU. SC380 is detected under the following conditions: • The Lock signal stays High 2 seconds after the motor turns on. • The Lock signal stays Low 2 seconds after the motor turns off. • The Lock signal stays High for more than 2 seconds while the motor is on. |
| Causes: | • Defective motor • Defective BCU |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the motor. 3. Replace the BCU. |
| Error code: | SC 385 |
| Description: | ID sensor VSG adjustment error Vsg is the out of adjustment range during a process control self-check. Adjustment range: 4.0 ± 0.5V |
| Causes: | • Defective ID sensor • Dirty ID sensor • ID sensor disconnected • Dirty drum (cleaning incomplete) |
| Remedy: | 1. Turn the main switch off and on. 2. Clean the ID sensor and adjacent parts. 3. Check the drum cleaning condition. 4. Check the ID sensor connector. 5. Replace the ID sensor. |
| Error code: | SC 386 |
| Description: | Development gamma error K Any of the following conditions happens three consecutive times: . When the development gamma is out of the following range: 0.3 <Y> 6.0 . When Vk is out of the following range: -150V <Y>150V . Development gamma calculation error |
| Causes: | • Unsuitable toner density • Toner supply mechanism problem • Laser exposure problem • Image transfer problem |
| Remedy: | 1. Turn the main switch off and on . 2. Check the process control self-check result (SP3-975). If the result is not .1., fix the problem according to the table in section 4.1.2. 3. Print a full color image by disabling SC detection (SP5-809-001) and check if the image quality is OK. If the image quality is not OK, fix the problem. Then, enable the SC detection again. |
| Error code: | SC 387 |
| Description: | Development gamma error Y Any of the following conditions happens three consecutive times: . When the development gamma is out of the following range: 0.3 <Y> 6.0 . When Vk is out of the following range: -150V <Y>150V . Development gamma calculation error |
| Causes: | • Unsuitable toner density • Toner supply mechanism problem • Laser exposure problem • Image transfer problem |
| Remedy: | 1. Turn the main switch off and on . 2. Check the process control self-check result (SP3-975). If the result is not .1., fix the problem according to the table in section 4.1.2. 3. Print a full color image by disabling SC detection (SP5-809-001) and check if the image quality is OK. If the image quality is not OK, fix the problem. Then, enable the SC detection again. |
| Error code: | SC 388 |
| Description: | Development gamma error C Any of the following conditions happens three consecutive times: . When the development gamma is out of the following range: 0.3 <Y> 6.0 . When Vk is out of the following range: -150V <Y>150V . Development gamma calculation error |
| Causes: | • Unsuitable toner density • Toner supply mechanism problem • Laser exposure problem • Image transfer problem |
| Remedy: | 1. Turn the main switch off and on . 2. Check the process control self-check result (SP3-975). If the result is not .1., fix the problem according to the table in section 4.1.2. 3. Print a full color image by disabling SC detection (SP5-809-001) and check if the image quality is OK. If the image quality is not OK, fix the problem. Then, enable the SC detection again. |
| Error code: | SC 389 |
| Description: | Development gamma error M Any of the following conditions happens three consecutive times: . When the development gamma is out of the following range: 0.3 <Y> 6.0 . When Vk is out of the following range: -150V <Y>150V . Development gamma calculation error |
| Causes: | • Unsuitable toner density • Toner supply mechanism problem • Laser exposure problem • Image transfer problem |
| Remedy: | 1. Turn the main switch off and on . 2. Check the process control self-check result (SP3-975). If the result is not .1., fix the problem according to the table in section 4.1.2. 3. Print a full color image by disabling SC detection (SP5-809-001) and check if the image quality is OK. If the image quality is not OK, fix the problem. Then, enable the SC detection again. |
| Error code: | SC 390 |
| Description: | Development Bias output error The high voltage supply board (C/B) monitors the circuit and detects abnormal conditions such as a voltage leak or no output condition. If this happens, the high voltage supply board sends an error signal (High to Low at CN204- A18) to the BCU. The BCU monitors this signal every 2 ms and generates this SC code when the error condition occurs 250 consecutive times. |
| Causes: | • Loose connection • Defective power pack C/B output • Damaged cable • Defective development unit • Defective BCU |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the harness and cables are properly connected. 3. Disconnect the high voltage supply cables from the bias terminals on the high voltage supply board C/B. Measure the DC voltage using a multi-meter. • Replace the high voltage supply board if no voltage is supplied. 4. If the result is OK at step 2, check if the high voltage supply cable or development unit is grounded. • Replace the high voltage supply cable if it damages. • Replace the development unit if it damages. 5. Check the PWM signals are sent to the high voltage supplied board from the BCU. Replace the BCU or harness between the BCU and high voltage supply board if the voltage is 0. |
| Error code: | SC 391-01 |
| Description: | Charge AC: output error 391-01: K 391-02: Y 391-03: M 391-04: C The high voltage supply board sends the feedback signal (CN228-2 to 5; MCYK). The BCU monitors these feedback signals every 8 ms. If the average of the sampled data is not within the control target 30 consecutive times, this SC code is generated. |
| Causes: | • Power pack disconnected • Charge receptacle or terminal • Defective PCU bias input terminal • Incorrect power pack B/C output • Damaged cable • Defective BCU |
| Remedy: | 1. Turn the main switch off and on. 2. Check the connector. 3. Check the PCU charge voltage input (the spring/conducting shaft) or replace the PCU. 4. Replace the power pack B/C. 5. Replace the cable. 6. Replace the BCU. |
| Error code: | SC 392-001 |
| Description: | Air pump motor error 391-001: MY 391-002: CK Three consecutive errors are detected in motor-driver-signal samples. The samples are collected every 0.01 second. |
| Causes: | • Damaged cable • Short circuit • Defective motor |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the air pump. 3. Check the circuit. |
| Error code: | SC 440-001 |
| Description: | Drum motor error 440-001: Black 440-002: Color No drum gear position sensor signal is detected within 0.7 second (185 mm/s), 1.0 second (125 mm/s), or 2.0 seconds (62.5 mm/s). |
| Causes: | • Defective PCU • Defective drum motor • Defective drum gear position sensor |
| Remedy: | 1. Turn the main switch off and on. 2. Check and/or replace the PCU. 3. Check and/or replace the sensor. |
| Error code: | SC 460-001 |
| Description: | Thermistor 1 error (open circuit) When the temperature detected by thermistor 1, which is at the left (fusing unit) side of the laser optics unit, is less than -30°C for 10 seconds consecutively, the BCU determines that the circuit is opened and displays this SC code. |
| Causes: | • Thermistor 1 defective • Cable connection error • BCU defect |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connections. 3. Replace the thermistor. 4. Replace the BCU. |
| Error code: | SC 460-002 |
| Description: | Thermistor 1 error (short circuit) When the temperature detected by the thermistor 1, which is at the left (fusing unit) side of the laser optics unit, is higher than 70°C for 10 seconds consecutively, the BCU determines that the circuit is shorted and displays this SC code |
| Causes: | • Thermistor 1 defective • Cable connection error • BCU defect |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connections. 3. Replace the thermistor. 4. Replace the BCU. |
| Error code: | SC 461-001 |
| Description: | Thermistor 2 error (open circuit) When the temperature detected by the thermistor 2, which is at the right (paper feed section) side of the laser optics unit, is less than -30°C for 10 seconds consecutively, the BCU determines that the circuit is opened and displays this SC code. |
| Causes: | • Thermistor 2 defective • Cable connection error • BCU defect |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connections. 3. Replace the thermistor. 4. Replace the BCU. |
| Error code: | SC 461-002 |
| Description: | Thermistor 2 error (short circuit) When the temperature detected by the thermistor 2, which is at the right (paper feed section) side of the laser optics unit, is higher than 70°C for 10 seconds consecutively, the BCU determines that the circuit is shorted and displays this SC code |
| Causes: | • Thermistor 2 defective • Cable connection error • BCU defect |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connections. 3. Replace the thermistor. 4. Replace the BCU. |
| Error code: | SC 471 |
| Description: | Transfer belt H.P. error The transfer belt HP sensor signal does not change from Low to High (home position) or vice versa 1 second after the transfer belt contact motor turns on. |
| Causes: | • Transfer belt unit not set properly • Defective transfer belt H.P. sensor and/or transfer belt sensor • Defective transfer belt contact motor • Transfer belt unit problem |
| Remedy: | 1. Turn the main switch off and on. 2. Reset the transfer belt unit. 3. Clean or replace the transfer belt sensor. 4. Replace the transfer belt contact motor. 5. Check the contact and release mechanism of the transfer belt unit. |
| Error code: | SC 490 |
| Description: | Transfer bias / paper attraction roller bias leak error The high voltage supply board - Transfer monitors the circuit and detects current leaks. If this happens, the high voltage supply board sends a SC signal (High to Low at CN213- 8) to the BCU. The BCU monitors this signal every 2 ms and generates this SC code when the error condition occurs 250 consecutive times. |
| Causes: | • Defective high voltage supply board - Transfer • Damaged transfer belt • Transfer unit • Damaged high voltage supply cables • Damaged cables between the BCU and high voltage supply board • Defective BCU |
| Remedy: | 1. Turn the main switch off and on. 2. Check the transfer unit and replace the belt and/or the transfer unit if any damage is found. 3. Replace the high voltage supply board - Transfer. 4. Check and/or replace the high voltage supply cables. 5. Check and/or replace the dc cables between the BCU and high voltage supply board. 6. Replace the BCU. |
| Error code: | SC 501 |
| Description: | Paper Tray 1 error When the tray lift motor is turned on, if the upper limit is not detected within 10 seconds, the machine asks the user to reset the tray. If this condition occurs three consecutive times, the SC is generated. |
| Causes: | • Defective paper lift sensor • Defective tray lift motor • Defective bottom plate lift mechanism |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the bottom plate smoothly moves up and down manually. 3. Check and/or replace the paper lift sensor. 4. Check and/or replace the tray lift motor. |
| Error code: | SC 502 |
| Description: | Paper Tray 2 error When the tray lift motor is turned on, if the upper limit is not detected within 10 seconds, the machine asks the user to reset the tray. If this condition occurs three consecutive times, the SC is generated. |
| Causes: | • Defective paper lift sensor • Defective tray lift motor • Defective bottom plate lift mechanism |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the bottom plate smoothly moves up and down manually. 3. Check and/or replace the paper lift sensor. 4. Check and/or replace the tray lift motor. |
| Error code: | SC 503-01 |
| Description: | Tray 3 error (Paper Feed Unit or LCT) For the paper feed unit: When the tray lift motor is turned on, if the upper limit is not detected within 18 seconds, the machine asks the user to reset the tray. If this condition occurs three consecutive times, the SC is generated. For the LCT: This SC is generated under the following conditions: • If the upper or lower limit is not detected within 15 seconds when the tray lift motor is turned on to lift up or lower the tray • If the paper stack is not transported within a specific number of pulses after the tray motor and stack transport clutch turn on to transport the paper stack • If the end fence home position sensor stays ON for a specific number of pulses after the tray motor and stack transport clutch turn on to transport the paper stack. |
| Causes: | For the paper feed unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection • Defective upper limit sensor or connector disconnection • Defective tray lift motor or connector disconnection |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connections. 3. Check and/or replace the defective component. |
| Error code: | SC 503-02 |
| Description: | Tray 3 error (Paper Feed Unit or LCT) • If the following condition occurs 3 consecutive times, this SC is generated. For the paper feed unit: When the main switch is turned or when the tray is set and if the upper limit is already detected, the lift motor turns on to lower the bottom plate until the lift sensor goes off. If the motor turns on for 7 seconds or more, the machine asks the user to reset the tray. For the LCT: When the main switch is turned on or when the LCT is set, if the end fence is not in the home position (home position sensor ON), the tray lift motor stops. |
| Causes: | For the paper feed unit: • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection For the LCT: • Defective stack transport clutch or connector disconnection • Defective tray motor or connector disconnection • Defective end fence home position sensor or connector disconnection |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connections. 3. Check and/or replace the defective component. |
| Error code: | SC 504-01 |
| Description: | Tray 4 error (3 Tray Paper Feed Unit) When the tray lift motor is turned on, if the upper limit is not detected within 18 seconds, the machine asks the user to reset the tray. If this condition occurs three consecutive times, the SC is generated. |
| Causes: | • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connections. 3. Check and/or replace the defective component. |
| Error code: | SC 504-02 |
| Description: | Tray 4 error (3 Tray Paper Feed Unit) When the main switch is turned or when the tray is set and if the upper limit is already detected, the lift motor turns on to lower the bottom plate until the lift sensor goes off. If the motor turns on for 7 seconds or more, the machine asks the user to reset the tray. If this condition occurs 3 consecutive times, this SC is generated. |
| Causes: | • Defective tray lift motor or connector disconnection • Defective lift sensor or connector disconnection |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connections. 3. Check and/or replace the defective component. |
| Error code: | SC 530 |
| Description: | Fusing fan motor error The BCU does not receive the lock signal (CN210-B5) 5 seconds after turning on the fusing fan. |
| Causes: | • Defective fusing fan motor or connector disconnection • Defective BCU |
| Remedy: | 1. Turn the main switch off and on. 2. Check the connector and/or replace the fusing fan motor. 3. Replace the BCU. |
| Error code: | SC 541 |
| Description: | Heating roller thermistor error The temperature measured by the heating roller thermistor does not reach 7 °C for ten seconds. |
| Causes: | • Loose connection of the heating roller thermistor • Defective heating roller thermistor • Defective BCU |
| Remedy: | 1. Check if the heating roller thermistor is firmly connected. 2. Replace the fusing unit. 3. Replace the BCU. |
| Error code: | SC 542 |
| Description: | Heating roller warm-up error After the main switch is turned on or the cover is closed, the heating roller temperature does not reach the ready temperature within 60 seconds during fusing unit warm-up. |
| Causes: | • Heating roller fusing lamp broken • Defective heating roller thermistor • Defective BCU |
| Remedy: | 1. Check if the heating roller thermistor is firmly connected. 2. Replace the fusing unit. 3. Replace the BCU. |
| Error code: | SC 543 |
| Description: | Heating roller fusing lamp overheat The detected fusing temperature stays at 200°C or more for five seconds. |
| Causes: | • Defective PSU • Defective BCU |
| Remedy: | 1. Replace the PSU. 2. Replace the BCU. |
| Error code: | SC 544 |
| Description: | Heating roller fusing lamp high temperature error During stand-by mode or a print job, the detected heating roller temperature stays at 210 °C or more for 0.1 second. |
| Causes: | • Defective heating roller thermistor • Defective PSU • Defective BCU |
| Remedy: | 1. Replace the fusing unit. 2. Replace the PSU. 3. Replace the BCU. |
| Error code: | SC 545 |
| Description: | Heating roller fusing lamp consecutive full power When the fusing unit is not running in the Ready condition, the heating roller fusing lamp keeps on with full power for 30 consecutive seconds. |
| Causes: | • Heating roller thermistor out of position |
| Remedy: | 1. Replace the fusing unit. |
| Error code: | SC 546 |
| Description: | Heating roller fusing lamp temperature fluctuation The heating roller temperature changes by ±20°C or more in one second. This occurs three times in one minute or two consecutive times. |
| Causes: | • Loose connection of the thermistor • Loose connection between the fusing unit and main frame |
| Remedy: | 1. Check if the fusing unit is properly set and connected to the main frame. 2. Check if the heating roller thermistor connector is firmly connected. 3. Replace the fusing unit. |
| Error code: | SC 551 |
| Description: | Pressure roller thermistor error The measured pressure roller temperature does not reach 7°C for 30 seconds. |
| Causes: | • Loose connection of pressure roller thermistor • Defective pressure roller thermistor • Defective BCU |
| Remedy: | 1. Check that the pressure roller thermistor is firmly connected. 2. Replace the fusing unit. 3. Replace the BCU. |
| Error code: | SC 552 |
| Description: | Pressure roller warm-up error After the main switch is turned on or the door is closed, the pressure roller temperature does not reach the ready temperature within 150 seconds during fusing unit warm-up. |
| Causes: | • Pressure roller fusing lamp broken • Defective pressure roller thermistor • Defective BCU |
| Remedy: | 1. Check if the pressure roller thermistor is firmly connected. 2. Replace the fusing unit. 3. Replace the BCU. |
| Error code: | SC 553 |
| Description: | Pressure roller fusing lamp overheat The detected pressure roller temperature stays at 200°C or more for five seconds. |
| Causes: | • Defective PSU • Defective BCU |
| Remedy: | 1. Replace the fusing unit. 2. Replace the PSU. 3. Replace the BCU. |
| Error code: | SC 554 |
| Description: | Pressure roller fusing lamp low temperature error During stand-by mode or printing, the detected pressure roller temperature stays at 50°C or less for five seconds. |
| Causes: | • Loose connection between the fusing unit and the machine • Defective pressure roller thermistor • Defective PSU • Defective BCU |
| Remedy: | 1. Check the connection between the fusing unit and main frame. 2. Replace the fusing unit. 3. Replace the PSU. 4. Replace the BCU. |
| Error code: | SC 555 |
| Description: | Pressure roller fusing lamp consecutive full power When the fusing unit is not running in the Ready condition, the pressure roller fusing lamp keeps ON with full power for 100 consecutive seconds. |
| Causes: | • Pressure roller thermistor out of position |
| Remedy: | 1. Replace the fusing unit. |
| Error code: | SC 556 |
| Description: | Pressure roller fusing lamp temperature fluctuation The pressure roller temperature changes by ±20°C or more in one second. This occurs three times in one minute or two consecutive times. |
| Causes: | • Loose connection of the pressure roller thermistor • Loose connection between the fusing unit and main frame |
| Remedy: | 1. Check if the fusing unit is properly set and connected to the main frame. 2. Check if the pressure roller thermistor connector is firmly connected. 3. Replace the fusing unit. |
| Error code: | SC 560 |
| Description: | Zero cross error When the main switch is turned on, the machine checks how many zero-cross signals are generated during 500 ms. If the number of zero-cross signal generated is either more than 66 or less than 45 and when this condition is detected 10 consecutive times, this code is displayed. |
| Causes: | • Electrical noise in the supply from the power cord |
| Remedy: | 1. Replace the PSU. |
| Error code: | SC 620 |
| Description: | ARDF communication error • After the ARDF is detected, the break signal occurs or communication timeout occurs. |
| Causes: | • Incorrect installation of ARDF • ARDF defective • IPU board defective • External noise |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection of the ARDF. 3. Shut out the external noise. 4. Replace the ARDF. 5. Replace the IPU board. |
| Error code: | SC 621 |
| Description: | Finisher/ mailbox communication error While the BCU communicates with an optional unit, an SC code is displayed if one of following conditions occurs. 1. The BCU receives a signal which is generated by the peripherals only just after the main switch is turned on. 2. When the BCU does not receive an OK signal from a peripheral 100ms after sending a command to it. The BCU resends the command. The BCU does not receive an OK signal after sending the command 3 times. |
| Causes: | • Cable problems • BCU problems • PSU problems in the machine • Main board problems in the peripherals |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the cables of peripherals are properly connected. 3. Replace the PSU if no power is supplied to peripherals. 4. Replace the BCU or main board of peripherals. |
| Error code: | SC 622 |
| Description: | Bank communication error While the BCU communicates with an optional unit, an SC code is displayed if one of following conditions occurs. 1. The BCU receives a signal which is generated by the peripherals only just after the main switch is turned on. 2. When the BCU does not receive an OK signal from a peripheral 100ms after sending a command to it. The BCU resends the command. The BCU does not receive an OK signal after sending the command 3 times. |
| Causes: | • Cable problems • BCU problems • PSU problems in the machine • Main board problems in the peripherals |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the cables of peripherals are properly connected. 3. Replace the PSU if no power is supplied to peripherals. 4. Replace the BCU or main board of peripherals. |
| Error code: | SC 623 |
| Description: | Duplex unit communication error While the BCU communicates with an optional unit, an SC code is displayed if one of following conditions occurs. 1. The BCU receives a signal which is generated by the peripherals only just after the main switch is turned on. 2. When the BCU does not receive an OK signal from a peripheral 100ms after sending a command to it. The BCU resends the command. The BCU does not receive an OK signal after sending the command 3 times. |
| Causes: | • Cable problems • BCU problems • PSU problems in the machine • Duplex control board problem |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the cable of the duplex inverter unit is properly connected. 3. Replace the PSU if no power is supplied to the peripherals. 4. Replace the duplex control board in the inverter unit. |
| Error code: | SC 640 |
| Description: | BCU - Controller communication error (check sum error) The check sum of the interface between the BCU and controller is not the same. |
| Causes: | • Defective controller • Defective PCU |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the controller. 3. Replace the BCU. |
| Error code: | SC 641 |
| Description: | BCU . Controller communication error (no response) The controller does not receive any response from the BCU three consecutive times when sending a signal every 100ms. |
| Causes: | • Loose connection • Defective controller • Defective BCU |
| Remedy: | 1. Turn the main switch off and on. 2. Check the connection between the BCU and controller. 3. Replace the controller. 4. Replace the BCU. |
| Error code: | SC 642 |
| Description: | Communication timeout error between controller and operation panel • The operation panel does not respond to the frame sent from the controller. |
| Causes: | • Controller defective • Operation panel defective • External noise • Harness between controller and operation panel disconnected |
| Remedy: | 1. Turn the main switch off an on. 2. Check the cable connection between the controller and the operation panel. 3. Shut out the external noise. 4. Replace the controller. 5. Replace the operation panel. |
| Error code: | SC 670 |
| Description: | No response from BCU at power on When the main power is turned on or the machine starts warming up from energy-saving mode, the controller does not receive a command signal from the BCU. |
| Causes: | • Loose connection • Defective controller • Defective BCU |
| Remedy: | 1. Turn the main switch off and on. 2. Check the connection between the BCU and controller. 3. Replace the controller. 4. Replace the BCU. |
| Error code: | SC 672 |
| Description: | Controller-tooperation panel communication error at startup • After the machine is powered on, the communication between the controller and the operation panel is not established, or communication with controller is interrupted after a normal startup. • After startup reset of the operation panel, the attention code or the attention acknowledge code is not sent from the controller. • After the controller issues a command to check the communication line with the controller at 30-second intervals, the controller fails to respond twice. |
| Causes: | • Controller stalled • Controller board installed incorrectly • Controller board defective • Operation panel connector loose or defective |
| Remedy: | 1. Turn the main switch off and on. 2. Check the condition of the controller board. 3. Check the condition of the operation panel. 4. Replace the controller board. 5. Replace the operation panel. |
| Error code: | SC 680 |
| Description: | BCU/ MUSIC communication error After the engine CPU sends a message, the Music CPU does not respond within five seconds three consecutive times. |
| Causes: | • Toner cartridge memory chip loose connection • Memory chip problem • Memory chip cable wiring problem |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the toner cartridge is installed correctly. 3. Replace the toner cartridge. 4. Check if the harnesses are not damaged. 5. Replace the BCU. |
| Error code: | SC 685 |
| Description: | SBU-IPU communication error • During data transfer, a checksum error occurs. • During any operation except initialization, the SBU sends a hardware-reset acknowledgement to the IPU. |
| Causes: | • Scanner unit cable connector loose • SBU board defective • IPU board defective • External noise |
| Remedy: | 1. Turn the main switch off and on. 2. Shut out the external noise. 3. Check the cable connection of the scanner unit. 4. Replace the SBU board. 5. Replace the IPU board. |
| Error code: | SC 686 |
| Description: | BCU-IPU communication error • After the machine is powered on or recovering from the power save mode, timeout occurs during BCU communication. • The break signal is received after the communication is normally established with the BCU. • Timeout occurs while the communication with the BCU is retried after a communication error. |
| Causes: | • Board connector between BCU and controller loose • Board connector between controller and bridge board loose • Board connector between bridge board and IPU loose • BCU board defective • IPU board defective • Controller board defective • Bridge board defective |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection between the board connector and BCU. 3. Check the cable connection between controller and bridge board. 4. Check the cable connection between bridge board and IPU. 5. Replace the BCU board. 6. Replace the IPU board. 7. Replace the controller board. 8. Replace the bridge board. |
| Error code: | SC 687 |
| Description: | Memory address command error The BCU does not receive a memory address command from the controller 60 seconds after paper is in the position for registration. |
| Causes: | • Loose connection • Defective controller • Defective BCU |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the controller is firmly connected to the BCU. 3. Replace the controller. 4. Replace the BCU. |
| Error code: | SC 690-001 |
| Description: | GAVD I2C communica-tion error 690-001: Y 690-002: M 690-003: C 690-004: K • The I2C bus device ID is not identified during initialization. • A device-status error occurs during I2C bus communication. • The I2C bus communication is not established due to an error other than a buffer shortage. |
| Causes: | • Loose connection • Defective BCU • Defective LD controller board |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection. 3. Replace the laser optics housing unit. 4. Replace the BCU board. |
| Error code: | SC 691 |
| Description: | Scanner startup error • After the machine is powered on or recovering from the power save mode, the scanner ready signal is not verified. |
| Causes: | • Board connector between controller and bridge board loose • Board connector between bridge board and IPU loose • IPU board defective • Controller board defective • Bridge board defective |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection between controller and bridge board. 3. Check the cable connection between bridge board and IPU. 4. Replace the IPU board. 5. Replace the controller board. 6. Replace the bridge board |
| Error code: | SC 700 |
| Description: | ARDF original pick-up malfunction • After the pick-up motor is turned on, the original stopper HP sensor is not activated. |
| Causes: | • Original stopper HP sensor defective • Pick-up motor defective (not rotating) • Timing belt out of position • ARDF main board defective |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the HP sensor. 3. Turn the main switch off and on. 4. Replace the pick-up motor. 5. Replace the control board. |
| Error code: | SC 701 |
| Description: | ARDF original pick-up/paper lift mechanism malfunction • The original pick-up HP sensor is not activated after the pick-up motor is turned on. |
| Causes: | • Original pick-up HP sensor defective • Pick-up motor defective • ARDF main board defective |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the pick-up motor. 3. Replace the control board. 4. Replace the HP sensor. |
| Error code: | SC 722 |
| Description: | Finisher jogger motor error • The jogger fences of the finisher do not return to home position within a specific time. • The finisher jogger motor does not leave home position within a given time. |
| Causes: | • Defective jogger H.P. sensor • Loose connection • Defective jogger motor |
| Remedy: | 1. Turn the main switch off and on. 2. Check the connection of jogger H.P. sensor and jogger motor connectors 3. Replace the jogger H.P. sensor. 4. Replace the jogger motor. |
| Error code: | SC 724 |
| Description: | Finisher staple hammer motor error Stapling does not finish within 150 ms after the staple hammer motor turns on. |
| Causes: | • Staple jam • Loose connection • Overload caused by stapling too many pages • Defective staple hammer motor |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the staple hammer motor connector is properly connected. 3. Check if the staple jam occurs. 4. Replace the staple hammer motor. |
| Error code: | SC 725 |
| Description: | Finisher stack feed-out motor error The stack feed-out belt H.P. sensor does not activate within a specified time after the stack feed-out motor turns on. |
| Causes: | • Defective stack feedout H.P. sensor • Loose connection • Stack feed-out motor overload • Defective stack feedout motor |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the connectors of the stack feed-out H.P. sensor and motor are properly connected. 3. Replace the stack feed-out H.P. sensor. 4. Replace the stack feed-out motor. |
| Error code: | SC 726 |
| Description: | Finisher shift tray 1 lift motor error • The upper stack height 1 sensor is activated consecutively (detecting paper) for 15 seconds after the shift tray starts moving up. • The upper stack height sensor 1 is deactivated consecutively (not detecting paper) for 15 seconds after the shift tray starts moving down. • When the upper tray moves from lower paper exit to the upper paper exit, the upper stack height 1 sensor is activated. |
| Causes: | • Loose connection • Defective upper stack height 1 sensor • Defective shift tray 1 lift motor • Motor overload |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the connectors of the sensor and motor are properly connected. 3. Replace the upper stack height 1 sensor. 4. Replace the shift tray 1 lift motor. |
| Error code: | SC 727 |
| Description: | Finisher stapler rotation motor error The stapler cannot return to its home position within a specified time after the stapler rotation motor starts rotating. |
| Causes: | • Loose connection • Defective stapler rotation motor • Motor overload |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the stapler rotation motor connector is properly connected. 3. Replace the stapler rotation motor. |
| Error code: | SC 729 |
| Description: | Finisher punch motor error The punch home position is not detected within 250 ms after the punch clutch turns on. |
| Causes: | • Loose connection • Defective punch H.P. sensor • Defective punch clutch • Defective punch hole motor |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the connectors of sensor, clutch and/or motor are properly connected. 3. Replace the punch H.P. sensor. 4. Replace the punch clutch. 5. Replace the punch hole motor. |
| Error code: | SC 730 |
| Description: | Finisher stapler motor error The stapler home position is not detected within a specified time after the staple motor turns on. |
| Causes: | • Loose connection • Defective stapler H.P. sensor • Defective stapler motor |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the connectors of the sensor and motor are properly connected. 3. Replace the stapler H.P. sensor. 4. Replace the stapler motor. |
| Error code: | SC 731 |
| Description: | Finisher exit guide plate motor error The exit guide plate open sensor is not activated within a specified time after the exit guide plate motor turns on. |
| Causes: | • Loose connection • Defective exit guide plate open sensor • Defective exit guide plate motor |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the connectors of the sensor and motor are properly connected. 3. Replace the exit guide plate open sensor. 4. Replace the exit guide plate motor. |
| Error code: | SC 732 |
| Description: | Finisher tray 1 shift motor error Tray 1 home position is not detected within a specified time after the tray 1 shift motor turns on. |
| Causes: | • Loose connection • Defective tray shift 1 sensor • Defective tray 1 shift motor |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the connectors of the sensor and motor are properly connected. 3. Replace the tray shift 1 sensor. 4. Replace the tray 1 shift motor. |
| Error code: | SC 733 |
| Description: | Finisher tray 2 lift motor error • The lower stack height 1 sensor is activated consecutively (detecting paper) for 15 seconds after the shift tray starts moving up. • The lower stack height sensor 1 is deactivated consecutively (not detecting paper) for 15 seconds after the shift tray starts moving down. |
| Causes: | • Loose connection • Defective lower stack height 1 sensor • Defective tray 2 lift motor • Motor overload |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the connectors of the sensor and motor are properly connected. 3. Replace the lower stack height 1 sensor. 4. Replace the tray 2 lift motor. |
| Error code: | SC 734 |
| Description: | Finisher tray 2 shift motor error Tray 2 home position is not detected within a specified time after the tray 2 shift motor turns on. |
| Causes: | • Loose connection • Defective tray shift 2 sensor • Defective tray 2 shift motor |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the connectors of the sensor and motor are properly connected. 3. Replace the tray shift 2 sensor. 4. Replace the tray 2 shift motor. |
| Error code: | SC 804 |
| Description: | Video input incomplete (K) • The scanner is requested to transfer video data, but does not issue the video transmission end command within the defined time. |
| Causes: | • Board connector between controller and bridge board loose • Board connector between bridge board and IPU loose • IPU board defective • Controller board defective • Bridge board defective |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection between controller and bridge board. 3. Check the cable connection between bridge board and IPU. 4. Replace the IPU board. 5. Replace the controller board. 6. Replace the bridge board. |
| Error code: | SC 805 |
| Description: | Video input incomplete (Y) • The scanner is requested to transfer video data, but does not issue the video transmission end command within the defined time. |
| Causes: | • Board connector between controller and bridge board loose • Board connector between bridge board and IPU loose • IPU board defective • Controller board defective • Bridge board defective |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection between controller and bridge board. 3. Check the cable connection between bridge board and IPU. 4. Replace the IPU board. 5. Replace the controller board. 6. Replace the bridge board. |
| Error code: | SC 806 |
| Description: | Video input incomplete (M) • The scanner is requested to transfer video data, but does not issue the video transmission end command within the defined time. |
| Causes: | • Board connector between controller and bridge board loose • Board connector between bridge board and IPU loose • IPU board defective • Controller board defective • Bridge board defective |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection between controller and bridge board. 3. Check the cable connection between bridge board and IPU. 4. Replace the IPU board. 5. Replace the controller board. 6. Replace the bridge board. |
| Error code: | SC 807 |
| Description: | Video input incomplete (C) • The scanner is requested to transfer video data, but does not issue the video transmission end command within the defined time. |
| Causes: | • Board connector between controller and bridge board loose • Board connector between bridge board and IPU loose • IPU board defective • Controller board defective • Bridge board defective |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection between controller and bridge board. 3. Check the cable connection between bridge board and IPU. 4. Replace the IPU board. 5. Replace the controller board. 6. Replace the bridge board. |
| Error code: | SC 808 |
| Description: | Video input incomplete (R) • The scanner is requested to transfer video data, but does not issue the video transmission end command within the defined time. |
| Causes: | • Board connector between controller and bridge board loose • Board connector between bridge board and IPU loose • IPU board defective • Controller board defective • Bridge board defective |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection between controller and bridge board. 3. Check the cable connection between bridge board and IPU. 4. Replace the IPU board. 5. Replace the controller board. 6. Replace the bridge board. |
| Error code: | SC 809 |
| Description: | Video input incomplete (G) • The scanner is requested to transfer video data, but does not issue the video transmission end command within the defined time. |
| Causes: | • Board connector between controller and bridge board loose • Board connector between bridge board and IPU loose • IPU board defective • Controller board defective • Bridge board defective |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection between controller and bridge board. 3. Check the cable connection between bridge board and IPU. 4. Replace the IPU board. 5. Replace the controller board. 6. Replace the bridge board. |
| Error code: | SC 810 |
| Description: | Video input incomplete (B) • The scanner is requested to transfer video data, but does not issue the video transmission end command within the defined time. |
| Causes: | • Board connector between controller and bridge board loose • Board connector between bridge board and IPU loose • IPU board defective • Controller board defective • Bridge board defective |
| Remedy: | 1. Turn the main switch off and on. 2. Check the cable connection between controller and bridge board. 3. Check the cable connection between bridge board and IPU. 4. Replace the IPU board. 5. Replace the controller board. 6. Replace the bridge board. |
| Error code: | SC 818 |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the controller. 3. See NOTE 1 at the end of the SC table |
| Error code: | SC 819 |
| Description: | Fatal error [696E] Process error System completely down [766D] Memory error Unexpected system memory size |
| Causes: | • Defective RAM DIMM • Defective ROM DIMM • Defective controller • Software error |
| Remedy: | 1. Turn the main switch off and on. 2. Check and/or replace the RAM DIMM. 3. Check and/or replace the ROM DIMM. 4. Replace the controller. 5. See NOTE at the end of the SC table. |
| Error code: | SC820 |
| Description: | Controller Error |
| Causes: | Unexpected error. |
| Remedy: | Cycle the machine off/on. |
| Error code: | SC 821 |
| Description: | 0D05] Self-diagnosis error: ASIC The CPU checks if the ASIC timer works properly compared with the CPU timer. If the ASIC timer does not function in the specified range, this SC code is displayed. |
| Causes: | • System firmware problem • Defective RAM-DIMM • Defective controller |
| Remedy: | 1. Turn the main switch off and on. 2. Reinstall the controller system firmware. 3. Replace the RAM-DIMM. 4. Replace the controller board. |
| Error code: | SC822 |
| Description: | Self-diagnostic error 2: HDD |
| Error code: | SC 823 |
| Description: | Self-diagnostic error: NIB [XXXX]: Detailed error code [6101] MAC address check sum error The result of the MAC address check sum does not match the check sum stored in ROM. [6104] PHY IC error The PHY IC on the controller cannot be properly recognized. [6105] PHY IC loopback error An error occurred during the loop-back test for the PHY IC on the controller. |
| Causes: | • Defective controller |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the controller. |
| Error code: | SC 824 |
| Description: | [1401] Self-diagnosis error: Standard NVRAM The controller cannot recognize the standard NVRAM installed or detects that the NVRAM is defective. |
| Causes: | • Loose connection • Defective standard NVRAM • Defective controller |
| Remedy: | 1. Turn the main switch off and on. 2. Check the standard NVRAM is firmly inserted into the socket. 3. Replace the NVRAM. 4. Replace the controller. |
| Error code: | SC 826 |
| Description: | Self-diagnostic Error: RTC/ Optional NVRAM • An RTC device is recognized, and the difference between the RTC device and the CPU exceeds the defined limit. • No RTC device is recognized. |
| Causes: | • RTC defective • NVRAM without RTC installed • Backup battery discharged |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the NVRAM with another NVRAM with an RTC device. |
| Error code: | SC 827 |
| Description: | Self-diagnostic error: Standard SRAM DIMM [XXXX]: Detailed error code [0201] Verification error Error detected during a write/verify check for the standard RAM (SRAM DIMM). |
| Causes: | • Loose connection • Defective SRAM DIMM • Defective controller |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the SRAM DIMM. 3. Replace the controller. |
| Error code: | SC 828 |
| Description: | Self-diagnostic error : ROM [XXXX]: Detailed error code [0101] Check sum error 1 The boot monitor and OS program stored in the ROM DIMM is checked. If the check sum of the program is incorrect, this SC code is displayed. [0104] Check sum error 2 All areas of the ROM DIMM are checked. If the check sum of all programs stored in the ROM DIMM is incorrect, this SC code is displayed. [0105] ROM error The ROM DIMM is not of the recognized type. |
| Causes: | • Defective ROM DIMM • Defective controller |
| Remedy: | 1. Turn the main switch on and off. 2. Replace the ROM DIMM 3. Replace the controller. |
| Error code: | SC829 |
| Description: | Self-diagnostic error 5: Optional RAM Verify error for optional RAM. |
| Causes: | • Make sure that the resident RAM is installed in the correct slot. • Make sure the optional RAM is installed in the correct slot (Slot 0) |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the RAM DIMM. 3. Replace the controller board. |
| Error code: | SC 833 |
| Description: | [0F21] Self-diagnostic error: I/F error The controller detects that the BCU is not properly connected. |
| Causes: | • Loose connection • Defective controller • Defective BCU |
| Remedy: | 1. Turn the main switch off and on. 2. Check the connection between the BCU and controller. 3. Replace the controller. 4. Replace the BCU. |
| Error code: | SC 835 |
| Description: | Self-diagnosis error: Centronics interface [XXXX]: Detailed error code [1102] Verification error The controller detects that the loop-back connector is not properly connected. [110C] DMA verification error A DMA data abnormality is detected even when the loopback connector is properly set. [1120] Loop-back connector error The loop-back connector is not set when starting the detailed self-diagnostics. |
| Causes: | • Loose connection • Defective loop-back connector • Defective Centronics connector • Defective controller |
| Remedy: | 1. Turn the main switch off and on. 2. Check the connection between the Centronics connector and loop-back connector. 3. Reconnect the loop-back connector. 4. Replace the controller. |
| Error code: | SC 836 |
| Description: | 1601] Self-diagnosis error: Font ROM (standard) The data in the font ROM (standard ROM-DIMM) is damaged |
| Causes: | • Defective standard ROM-DIMM |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the standard ROM-DIMM. |
| Error code: | SC 837 |
| Description: | 1602] Self-diagnosis error: Font ROM (option) The data in the font ROM (optional ROM-DIMM) is damaged |
| Causes: | • Defective optional ROM-DIMM |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the optional ROM-DIMM. |
| Error code: | SC 850 |
| Description: | Network interface error The network is unusable. |
| Causes: | • Defective controller |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the controller. |
| Error code: | SC 851 |
| Description: | IEEE1394 interface error The 1394 interface is unusable. |
| Causes: | • Defective IEEE1394 • Defective controller. |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the IEEE1394 interface board. 3. Replace the controller. |
| Error code: | SC 853 |
| Description: | Wireless LAN card not detected The wireless LAN card is not detected before communication is established, though the wireless LAN board is detected. |
| Causes: | • Loose connection |
| Remedy: | 1. Check the connection. |
| Error code: | SC 854 |
| Description: | Wireless LAN card not detected The wireless LAN card is not detected after communication is established, though the wireless LAN board is detected. |
| Causes: | • Loose connection |
| Remedy: | 1. Check the connection. |
| Error code: | SC 855 |
| Description: | Wireless LAN card error An error is detected in the wireless LAN card. |
| Causes: | • Loose connection • Defective wireless LAN card |
| Remedy: | 1. Check the connection. 2. Replace the wireless LAN card. |
| Error code: | SC 856 |
| Description: | Wireless LAN card error An error is detected in the wireless LAN board. |
| Causes: | • Defective wireless LAN board • Loose connection |
| Remedy: | 1. Check the connection. 2. Replace the wireless LAN board. |
| Error code: | SC 857 |
| Description: | USB interface error The USB interface cannot be used due to a driver error. |
| Causes: | • Defective USB driver • Loose connection |
| Remedy: | 1. Check the connection. 2. Replace the controller. |
| Error code: | SC 860 |
| Description: | HDD: Initialization error The controller detects that the hard disk fails. |
| Causes: | • HDD not initialized • Defective HDD |
| Remedy: | 1. Turn the main switch off and on. 2. Reformat the HDD. 3. Replace the HDD. |
| Error code: | SC 861 |
| Description: | HDD: Reboot error The HDD does not become ready within 30 seconds after the power is supplied to the HDD. |
| Causes: | • Loose connection • Defective cables • Defective HDD • Defective controller |
| Remedy: | 1. Turn the main switch off and on. 2. Check the connection between the HDD and controller. 3. Check and replace the cables. 4. Replace the HDD. 5. Replace the controller. |
| Error code: | SC 863 |
| Description: | HDD: Read error The data stored in the HDD cannot be read correctly. |
| Causes: | • Defective HDD • Defective controller |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the HDD. 3. Replace the controller. |
| Error code: | SC 864 |
| Description: | HDD: CRC error While reading data from the HDD or storing data in the HDD, data transmission fails. |
| Causes: | • Defective HDD |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the HDD. |
| Error code: | SC 865 |
| Description: | HDD: Access error An error is detected while operating the HDD. |
| Causes: | • Defective HDD |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the HDD. |
| Error code: | SC 900 |
| Description: | Electric counter error Abnormal data is stored in the counters. |
| Causes: | • Defective NVRAM • Defective controller |
| Remedy: | 1. Turn the main switch off and on. 2. Check the connection between the NVRAM and controller. 3. Replace the NVRAM. 4. Replace the controller. |
| Error code: | SC 990 |
| Description: | Software performance error The software makes an unexpected operation. |
| Causes: | • Defective software • Defective controller • Software error |
| Remedy: | 1. Turn the main switch off and on. 2. Reinstall the controller and/or engine main firmware. 3. See NOTE 1 at the end of the SC table |
| Error code: | SC 997 |
| Description: | Application function selection error • The application selected by the operation panel key does not start or ends abnormally. |
| Causes: | • Software (including the software configuration) defective • An option required by the application (RAM, DIMM, board) is not installed |
| Remedy: | 1. Check the devices necessary for the application program. If necessary devices have not been installed, install them. 2. Check that application programs are correctly configured. 3. Take necessary countermeasures specific to the application program. If the logs can be displayed on the operation panel, see the logs. |
| Error code: | SC 998 |
| Description: | Application start error No applications start within 60 seconds after the power is turned on. |
| Causes: | • Loose connection of RAM-DIMM, ROMDIMM • Defective controller • Software problem |
| Remedy: | 1. Turn the main switch off and on. 2. Check if the RAM-DIMM and ROMDIMM are properly connected. 3. Reinstall the controller system firmware. 4. Replace the controller. |
| Error code: | SC 999 |
| Description: | Program download error • The download (program, print data, language data) from the IC card does not execute normally. |
| Causes: | • Board installed incorrectly • Engine board defective • IC card defective • Incorrect IC card used (machine type/model, card version) • NVRAM defective • Loss of power during downloading NOTE 1: This error is not logged because the error occurs in the download mode (different from the normal operation mode). NOTE 2: If the machine loses power while downloading, or if the download does not normally end for some other reason, this could damage the controller board or the target PCB of the downloading and prevent subsequent downloading. If this problem occurs, the damaged PCB must be replaced. |
| Remedy: | 1. Turn the main switch off and on. 2. If you can download necessary programs, do it by using an appropriate card. 3. If you cannot download necessary programs, use the special card and tool for downloading or replace the board having been used for the unsuccessful downloading. |
Парткод
Название
RICOH TYPE 3800H Ролики подачи
RICOH TYPE 3800B Блок проявки цветной CMY
RICOH TYPE 7000B Блок проявки цветной CMY
RICOH TYPE 3800D Блок проявки черный
RICOH TYPE 7000D Блок проявки черный
RICOH TYPE 3800E Бункер для отработанного тонера
RICOH TYPE 7000G Ремкомплект узла подачи масла
RICOH TYPE 7000A Блок фотобарабана цветной CMY
RICOH TYPE 7000F Блок фотобарабана черный
RICOH TYPE 7000C Блок термозакрепления 220v (Печка)
RICOH TYPE K Скрепки с картриджем
RICOH TYPE K Скрепки (3 упаковки)
RICOH TYPE 205/105 Тонер-картридж черный
RICOH TYPE 105 Тонер-картридж желтый
RICOH TYPE 105 Тонер-картридж пурпурный
RICOH TYPE 105 Тонер-картридж голубой
