Ricoh Aficio 3232C
Рейтинг
Модули
SCANNER UNIT 1
Registration
PCU UNIT
VERTICAL TRANSFER 1
ELECTRICAL SECTION 4
ELECTRICAL SECTION 5
OPERATION PANEL
DRIVE SECTION 2
ELECTRICAL SECTION 1
PAPER TRAY 2
ELECTRICAL SECTION 2
FUSING UNIT 1
DRIVE SECTION 3
EXTERIOR 2
VERTICAL TRANSFER 2
SCANNER UNIT 2
LASER UNIT
FUSING UNIT 2
PAPER TRAY 1
ELECTRICAL SECTION 3
Drive Section 1
Paper exit
FUSING UNIT 3
VERTICAL TRANSFER 3
DEVELOPMENT UNIT
FRAME SECTION
EXTERIOR 1
Детали FUSING UNIT 3
| Деталь: | Frame:Scanner:Front |
| Парткод: | B051 1727 |
| Деталь: | Exposure Glass Cushion |
| Парткод: | 54 421 924 |
| Деталь: | Original Sensor:H81.5 |
| Парткод: | AW01 0115 |
| Деталь: | Stabilizer:Xenon Lamp |
| Парткод: | AZ50 0066 |
| Деталь: | Sheet Through Bracket - DF |
| Парткод: | B051 1801 |
| Деталь: | Seal - Exposure Glass |
| Парткод: | B051 1803 |
| Деталь: | Lens:Holder:Assy |
| Парткод: | B156 1684 |
| Деталь: | Bracket:Original Sensor |
| Парткод: | B051 1814 |
| Деталь: | Original Sensor:H2-66 |
| Парткод: | AW01 0114 |
| Деталь: | Interface Cable:BICU:HF |
| Парткод: | B154 5336 |
| Деталь: | Scanner Home Sensor Stopper |
| Парткод: | A1931793 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Inner cover |
| Парткод: | B1801701 |
| Деталь: | Bracket - Document Feeder Hinge |
| Парткод: | B051 1800 |
| Деталь: | PCB:SIO |
| Парткод: | B154 5130 |
| Деталь: | Harness:Scanner:DC:Assy |
| Парткод: | B154 5330 |
| Деталь: | Original Sensor:H1-66 |
| Парткод: | AW01 0116 |
| Деталь: | Bracket:Stabilizer |
| Парткод: | B1541825 |
| Деталь: | Guide:High Voltage Supply Cord:Base |
| Парткод: | B1801803 |
| Деталь: | Cover:Sensor:AKS |
| Парткод: | B154 1826 |
| Деталь: | Harness :AKS |
| Парткод: | B154 5332 |
| Деталь: | Harness:Scanner: Invertor |
| Парткод: | B154 5335 |
| Деталь: | Harness:Scanner:Motor |
| Парткод: | B154 5337 |
| Деталь: | GRIP |
| Парткод: | B1801801 |
| Деталь: | Slide Rail |
| Парткод: | G070 6145 |
| Деталь: | Grounding Plate - Slide Rail |
| Парткод: | G070 6175 |
| Деталь: | Slide Rail Stopper |
| Парткод: | G070 6157 |
| Деталь: | Rail:PCU:Left Lower:Assy |
| Парткод: | B154 6150 |
| Деталь: | Cover:Power Supply |
| Парткод: | B154 6158 |
| Деталь: | Rail:PCU:Right Lower:Assy |
| Парткод: | B154 6152 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Roller:Vertical Transport:Drive |
| Парткод: | AF02 0645 |
| Деталь: | Gear - 28Z |
| Парткод: | AB01 1225 |
| Деталь: | Gap Gear Guide |
| Парткод: | G0701197 |
| Деталь: | Bushing - Registration Roller |
| Парткод: | A267 2674 |
| Деталь: | Registration Roller:Drive |
| Парткод: | AF02 0644 |
| Деталь: | Registration Sensor Bracket |
| Парткод: | G070 2577 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW01 0117 |
| Деталь: | Harness:PPI:Registration Sensor |
| Парткод: | B154 5410 |
| Деталь: | Registration Guide |
| Парткод: | G070 2573 |
| Деталь: | Ground Plate:Registration Roller:Drive |
| Парткод: | G070 2578 |
| Деталь: | Photo Conductor Unit |
| Парткод: | B214 2300 |
| Деталь: | O/O |
| Парткод: | B214 2301 |
| Деталь: | Charge Corona Assembly |
| Парткод: | B051 2160 |
| Деталь: | Waste Toner Botle - OPC Belt |
| Парткод: | B051 2100 |
| Деталь: | Case:Toner Recycling:Assy |
| Парткод: | B051 6311 |
| Деталь: | Flanged Hexagonal Head Bolt -M4x14 |
| Парткод: | G070 2358 |
| Деталь: | Cleaner Screw Shaft |
| Парткод: | G070 2165 |
| Деталь: | PCU Drive Joint |
| Парткод: | G070 2318 |
| Деталь: | Wire Cleaning Motor - DC0.46W |
| Парткод: | G070 2176 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 0087 |
| Деталь: | Spacer - 4x6x1 |
| Парткод: | A096 3863 |
| Деталь: | Corona Wire:Charge Corona |
| Парткод: | G070 2110 |
| Деталь: | Corona Wire Spring |
| Парткод: | 54 422 108 |
| Деталь: | Positioning Pin |
| Парткод: | A172 7611 |
| Деталь: | Charge Corona Grid |
| Парткод: | G070 2156 |
| Деталь: | Seal - Charge Corona |
| Парткод: | G070 2142 |
| Деталь: | Charge Corona Cleaner Holder |
| Парткод: | G070 2167 |
| Деталь: | FRONT POSITIONING PLATE |
| Парткод: | B154 2119 |
| Деталь: | Raer Positioning Plate |
| Парткод: | B154 2120 |
| Деталь: | DC Moter Cover - Charge Corona |
| Парткод: | G070 2173 |
| Деталь: | Tension Spring:Cleaning Blade |
| Парткод: | B154 6412 |
| Деталь: | Doble Gear - 15Z/23Z |
| Парткод: | AB01 7595 |
| Деталь: | Rear Bracket - ITB Cleaning Unit |
| Парткод: | B154 6394 |
| Деталь: | Idler Gear - 20Z |
| Парткод: | AB01 4215 |
| Деталь: | Idler Gear - 19Z |
| Парткод: | AB01 4224 |
| Деталь: | Gear:Drive |
| Парткод: | AB01 7695 |
| Деталь: | Gear - 21Z |
| Парткод: | AB01 1475 |
| Деталь: | Knob Screw:Charge Corona |
| Парткод: | B154 2174 |
| Деталь: | Grid Shadeing Plate |
| Парткод: | G0702136 |
| Деталь: | Front End Block Cover |
| Парткод: | G0702159 |
| Деталь: | Rear End Block Cover |
| Парткод: | G0702160 |
| Деталь: | Rear Bracket - Grid Plate |
| Парткод: | G070 2161 |
| Деталь: | Spring Plate - Gridtension |
| Парткод: | G0702162 |
| Деталь: | Spring Plate - Screw Shaft |
| Парткод: | G0702163 |
| Деталь: | Cleaner Slider - Charge Corona |
| Парткод: | G070 2166 |
| Деталь: | Charge Corona Cleaner |
| Парткод: | G070 2168 |
| Деталь: | Gear - 20Z |
| Парткод: | AB01 1472 |
| Деталь: | Gear - 13Z |
| Парткод: | AB01 1473 |
| Деталь: | Gear - 24Z |
| Парткод: | AB01 1474 |
| Деталь: | Idler Gear - 35Z |
| Парткод: | AB01 1476 |
| Деталь: | OPC Cleaning Unit |
| Парткод: | B154 2051 |
| Деталь: | Belt Cleaning Assembly |
| Парткод: | B154 6300 |
| Деталь: | Cap - 20mm |
| Парткод: | A257 3490 |
| Деталь: | Spacer - Endblock |
| Парткод: | G070 2164 |
| Деталь: | Slider Ring |
| Парткод: | A172 7650 |
| Деталь: | Casing:Charge Corona:Assy |
| Парткод: | G070 2152 |
| Деталь: | Protection Sheet |
| Парткод: | G070 2116 |
| Деталь: | Roller - Guide |
| Парткод: | A860 2560 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Photointerruptor:Vertical T ransport |
| Парткод: | AW02 0171 |
| Деталь: | Guide Plate - Paper Feed2 |
| Парткод: | B051 2568 |
| Деталь: | Roller:Vertical Transport:Drive |
| Парткод: | AF02 0645 |
| Деталь: | Upper Guide Plate - Paper Feed2 |
| Парткод: | B051 2553 |
| Деталь: | Guide Plate - Vertical Transport |
| Парткод: | B051 2610 |
| Деталь: | Cover - Vertical Transport |
| Парткод: | B051 2551 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG07 0514 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0254 |
| Деталь: | Compresion Spring |
| Парткод: | B051 2557 |
| Деталь: | Roller:Driven:Assy |
| Парткод: | B154 2862 |
| Деталь: | Stopper Band |
| Парткод: | B051 2558 |
| Деталь: | Paper End Sensor Feeler |
| Парткод: | G070 2646 |
| Деталь: | LEVER SPRING |
| Парткод: | AA06 0866 |
| Деталь: | Release Lever |
| Парткод: | G070 2645 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Bracket - Paper End Sensor2 |
| Парткод: | B051 2550 |
| Деталь: | Feeler - Paper Bolume Sensor |
| Парткод: | G070 2647 |
| Деталь: | Sensor Rear Bracket |
| Парткод: | G070 2644 |
| Деталь: | Harness:Paper Feed:No.2:Sensor |
| Парткод: | B154 5471 |
| Деталь: | Seal - Plate |
| Парткод: | G070 2648 |
| Деталь: | Rear Link Lever |
| Парткод: | G070 5573 |
| Деталь: | Link Lever - Rear Right |
| Парткод: | G070 5574 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | G070 5575 |
| Деталь: | Link Outer Lever |
| Парткод: | G070 5564 |
| Деталь: | Link Middle Lever - Left |
| Парткод: | G070 5570 |
| Деталь: | Right Tension Spring |
| Парткод: | G070 5566 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG07 0514 |
| Деталь: | Lower Case - Safety Switch |
| Парткод: | G070 5561 |
| Деталь: | Right Link - Safety Switch |
| Парткод: | G070 5568 |
| Деталь: | Right Tension Spring |
| Парткод: | G070 5565 |
| Деталь: | Link Middle Lever |
| Парткод: | G070 5563 |
| Деталь: | Harness:IOB:Door Switch:24VS |
| Парткод: | B154 5415 |
| Деталь: | Harness:Door Switch:Unit |
| Парткод: | B154 5420 |
| Деталь: | Upper Case - Safety Switch |
| Парткод: | G070 5562 |
| Деталь: | Bracket - Total Counter |
| Парткод: | B051 5860 |
| Деталь: | Bracket - Main Switch |
| Парткод: | B051 5861 |
| Деталь: | Harness:Main Switch |
| Парткод: | B154 5464 |
| Деталь: | Rail - Left Front |
| Парткод: | B051 1111 |
| Деталь: | Grip Bracket - Left Front |
| Парткод: | B051 1079 |
| Деталь: | GRIP |
| Парткод: | B154 1058 |
| Деталь: | Left Cover Hinge |
| Парткод: | G0701075 |
| Деталь: | Front Lower Guide |
| Парткод: | G070 2335 |
| Деталь: | Heater Assembly (120 V) |
| Парткод: | B051 2547 |
| Деталь: | Heater Assembly (230V) |
| Парткод: | B051 2548 |
| Деталь: | Total Counter:7FIG:24V (NA only) |
| Парткод: | AX31 0049 |
| Деталь: | COVER HINGE |
| Парткод: | G0701074 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0024 |
| Деталь: | Holder - Paper Tray |
| Парткод: | G060 2801 |
| Деталь: | Grip:Right |
| Парткод: | B1541059 |
| Деталь: | Grip Bracket - Front Right |
| Парткод: | B051 1132 |
| Деталь: | Total Counter:7FIG:24V |
| Парткод: | AX31 0045 |
| Деталь: | Stopper - Link |
| Парткод: | B051 1128 |
| Деталь: | Cushion - Safety Switch |
| Парткод: | G070 5576 |
| Деталь: | Harness:PPI:Discharge |
| Парткод: | B154 5407 |
| Деталь: | Connector Holder |
| Парткод: | G070 2118 |
| Деталь: | Terminal Holder |
| Парткод: | G070 2126 |
| Деталь: | Terminal:Charge Corona |
| Парткод: | B154 2140 |
| Деталь: | TERMINAL |
| Парткод: | G070 6165 |
| Деталь: | Terminal Holder |
| Парткод: | G070 6166 |
| Деталь: | PCU Grounding Plate |
| Парткод: | G070 2336 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Positioning Sensor:Intermediate Transfer Bell |
| Парткод: | AW01 0108 |
| Деталь: | Bracket:Positioning Sensor |
| Парткод: | B154 6160 |
| Деталь: | Grounding Plate - Belt Cleaning |
| Парткод: | G070 6406 |
| Деталь: | Harness:IOB:Connecting:Mark |
| Парткод: | B154 5482 |
| Деталь: | Feeler |
| Парткод: | G070 2096 |
| Деталь: | SPRING |
| Парткод: | AA06 6633 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Waste Toner Bottle Bracket |
| Парткод: | G070 2107 |
| Деталь: | Bracket - Waste Toner Sensor |
| Парткод: | G070 6407 |
| Деталь: | Paper End Sensor Feeler |
| Парткод: | G070 2646 |
| Деталь: | LEVER SPRING |
| Парткод: | AA06 0866 |
| Деталь: | Release Lever |
| Парткод: | G070 2645 |
| Деталь: | Feeler - Paper Bolume Sensor |
| Парткод: | G070 2647 |
| Деталь: | Paper End Sensor Bracket |
| Парткод: | G070 2642 |
| Деталь: | Sensor Rear Bracket |
| Парткод: | G070 2644 |
| Деталь: | Vertical Transport Feeler |
| Парткод: | G070 2638 |
| Деталь: | Harness:PPI:Paper Feed |
| Парткод: | B154 5409 |
| Деталь: | Seal - Plate |
| Парткод: | G070 2648 |
| Деталь: | Harness:PPI:High Voltage Line:Discharge |
| Парткод: | B154 5450 |
| Деталь: | Harness:PPI:High Voltage Line:T2 |
| Парткод: | B154 5451 |
| Деталь: | Power Pack:BCTCLD |
| Парткод: | AZ30 0055 |
| Деталь: | Sensor Front Bracket |
| Парткод: | G070 2643 |
| Деталь: | Feeler Holder - Vertical Transport |
| Парткод: | G070 2637 |
| Деталь: | Connector Guide |
| Парткод: | G070 2143 |
| Деталь: | Charge Spring |
| Парткод: | G070 2138 |
| Деталь: | Operation Sub-unit:T-C1:NA:Assy |
| Парткод: | B154 1455 |
| Деталь: | Operation Sub-unit:T-C1:EU:Assy |
| Парткод: | B154 1456 |
| Деталь: | Operation Sub-unit:T-C1:AA:Assy |
| Парткод: | B1541458 |
| Деталь: | PCB:Operation Sub-unit:Right |
| Парткод: | B1801991 |
| Деталь: | Sheet Power Source (NA/Asia) |
| Парткод: | G570 2068 |
| Деталь: | Sheet Power Source (EU) |
| Парткод: | G570 2078 |
| Деталь: | Keytop Cover - Right |
| Парткод: | G5701971 |
| Деталь: | Sheet - Color C |
| Парткод: | G5701966 |
| Деталь: | Sheet LED - English |
| Парткод: | G570 2080 |
| Деталь: | Keytop Switch - Large |
| Парткод: | G5701963 |
| Деталь: | Lens - Data Input |
| Парткод: | G5701972 |
| Деталь: | Keytop - Color Adjust |
| Парткод: | G5701948 |
| Деталь: | Keytop - Counter |
| Парткод: | G5701951 |
| Деталь: | Keytop - ACS |
| Парткод: | B051 1482 |
| Деталь: | Keytop - Color Select |
| Парткод: | G5701953 |
| Деталь: | Knob - Contrast |
| Парткод: | G5701964 |
| Деталь: | PCB:Operation Sub-unit:Left |
| Парткод: | B1801990 |
| Деталь: | PCB LCDC |
| Парткод: | B180 5255 |
| Деталь: | Cover:LCDC |
| Парткод: | B180 1456 |
| Деталь: | Bracket:Operation Sub-unit:LCD |
| Парткод: | B1801455 |
| Деталь: | LCD:HVGA:SH:BL |
| Парткод: | B180 5259 |
| Деталь: | Touch Panel:HVGA |
| Парткод: | B213 5222 |
| Деталь: | Keytop - Check Modes |
| Парткод: | G570 1947 |
| Деталь: | Keytop - Program |
| Парткод: | G5701950 |
| Деталь: | Keytop Clear Modes - EXP |
| Парткод: | G570 2062 |
| Деталь: | Keytop - Energy Saver |
| Парткод: | G5701946 |
| Деталь: | Keytop - Interrupt |
| Парткод: | G5701945 |
| Деталь: | Keytop - Power Source |
| Парткод: | G5701967 |
| Деталь: | Keytop - Sample Copy |
| Парткод: | G5701943 |
| Деталь: | Keytop - Clear/Stop |
| Парткод: | G5701942 |
| Деталь: | Keytop - 10key (NA) |
| Парткод: | G570 2061 |
| Деталь: | Keytop - 10key (EU) |
| Парткод: | G5701944 |
| Деталь: | Keytop - 10key (AA) |
| Парткод: | B051 1491 |
| Деталь: | Keytop - Start/Stop |
| Парткод: | G570 1941 |
| Деталь: | Keytop - Switch (NA/Asia) |
| Парткод: | G570 2064 |
| Деталь: | Keytop - Switch (EU) |
| Парткод: | G570 2074 |
| Деталь: | Keytop Copy (NA/Asia) |
| Парткод: | G570 2063 |
| Деталь: | Keytop Copy (EU) |
| Парткод: | G570 2073 |
| Деталь: | Case - Operation Panel(NA/Asia) |
| Парткод: | B051 1485 |
| Деталь: | Case - Operation Panel (EU) |
| Парткод: | G570 2051 |
| Деталь: | Keytop Scanner - NA (Letter) |
| Парткод: | G570 2067 |
| Деталь: | Keytop Scanner - EU (Symbol) |
| Парткод: | G570 2077 |
| Деталь: | Keytop Printer - NA (Letter) |
| Парткод: | G570 2066 |
| Деталь: | Keytop Printer - EU (Symbol) |
| Парткод: | G570 2076 |
| Деталь: | Brushless Motor:26W:10Z |
| Парткод: | AX06 0290 |
| Деталь: | Bracket:T ransport:Assy |
| Парткод: | B154 4801 |
| Деталь: | Bracket:Transport |
| Парткод: | B154 4806 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Bracket:Arm |
| Парткод: | B154 4825 |
| Деталь: | Spring Clutch - 27Z |
| Парткод: | AB04 0020 |
| Деталь: | Gear - 33Z/27Z |
| Парткод: | G070 4850 |
| Деталь: | Bracket:Swivel:Assy |
| Парткод: | G070 4816 |
| Деталь: | Gear - 25Z/36Z |
| Парткод: | G070 4851 |
| Деталь: | Gear -30Z |
| Парткод: | AB01 4209 |
| Деталь: | Gear -33Z |
| Парткод: | AB01 4210 |
| Деталь: | Shaft:Drive:Second |
| Парткод: | AA14 9942 |
| Деталь: | DC Solenoid:On-Off:Peen |
| Парткод: | B154 4820 |
| Деталь: | Magnetic Clutch:32Z:0.5N M |
| Парткод: | AX20 0295 |
| Деталь: | Shaft:Drive:Cleaning |
| Парткод: | AA14 9950 |
| Деталь: | Gear - 24Z/53Z |
| Парткод: | AB01 7556 |
| Деталь: | Grar - 65z/20z |
| Парткод: | AB01 7557 |
| Деталь: | Shaft:On-Off:Cleaning |
| Парткод: | AA14 9944 |
| Деталь: | Gear -49Z |
| Парткод: | G070 4830 |
| Деталь: | Shaft:On-Off:Second |
| Парткод: | B154 4832 |
| Деталь: | Cam Roller |
| Парткод: | G070 4834 |
| Деталь: | SPRING SPACER |
| Парткод: | G070 4823 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 3657 |
| Деталь: | Gear -18Z |
| Парткод: | AB01 1479 |
| Деталь: | Cleaning On/off Cam |
| Парткод: | G0704818 |
| Деталь: | Tension Spring - Arm |
| Парткод: | AA06 0884 |
| Деталь: | Timing Belt:S2M:T122 |
| Парткод: | AA04 3589 |
| Деталь: | Timing Pulley-24Z/31T |
| Парткод: | AB01 7718 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0868 |
| Деталь: | Tightener |
| Парткод: | B154 4741 |
| Деталь: | Gear-98Z/33T |
| Парткод: | AB01 7717 |
| Деталь: | On/Off Cam |
| Парткод: | G070 4829 |
| Деталь: | Bushing:6x10x4 |
| Парткод: | AA08 2146 |
| Деталь: | STEPPED SCREW |
| Парткод: | AA14 3499 |
| Деталь: | Rubber Cushion |
| Парткод: | AA16 1125 |
| Деталь: | Bracket:HDD:Upper |
| Парткод: | B753 5880 |
| Деталь: | HDD:Hitachi:40GB:Pathfinder |
| Парткод: | B514 5980 |
| Деталь: | Bracket:HDD:Lower |
| Парткод: | B753 5881 |
| Деталь: | Cover:HDD:Large |
| Парткод: | B753 5882 |
| Деталь: | Harness:HDD:Power Source:Assy |
| Парткод: | B753 5952 |
| Деталь: | Harness:IDE:HDD:Assy |
| Парткод: | B753 5955 |
| Деталь: | Cover:HDD:Small |
| Парткод: | B753 5883 |
| Деталь: | Left Rail |
| Парткод: | B070 5671 |
| Деталь: | Right Rail |
| Парткод: | B070 5670 |
| Деталь: | Cover:Control Unit |
| Парткод: | B154 5855 |
| Деталь: | Cover:NOVITA2 |
| Парткод: | G395 5500 |
| Деталь: | PCB:NOBITA-S:Assy |
| Парткод: | G395 5003 |
| Деталь: | PCB:Type-BZ_UC2 |
| Парткод: | B154 5160 |
| Деталь: | PCB:DDR-DIMM:256MB:Assy |
| Парткод: | B585 5030 |
| Деталь: | PCB:DDR-DIMM:512MB |
| Парткод: | G108 5020 |
| Деталь: | Panel:SD-Card |
| Парткод: | B154 5859 |
| Деталь: | Panel:Interface:Secc (RAI) |
| Парткод: | B154 5869 |
| Деталь: | Interface Panel O/O (GOTENBA) |
| Парткод: | B101 5993 |
| Деталь: | Cover:Application:Sub-Assy |
| Парткод: | B154 5825 |
| Деталь: | Bracket:Control Unit:Upper |
| Парткод: | B154 5852 |
| Деталь: | Bracket:Control Unit |
| Парткод: | B154 5851 |
| Деталь: | PCB:BICU |
| Парткод: | B154 5210 |
| Деталь: | Bracket:Control Unit:Lower |
| Парткод: | B154 5853 |
| Деталь: | Fan:Axial:MM80 |
| Парткод: | AX64 0166 |
| Деталь: | Guard:Fan |
| Парткод: | B154 5861 |
| Деталь: | Bracket:Control Unit:Left |
| Парткод: | B154 5854 |
| Деталь: | HDD:Assy |
| Парткод: | B753 5010 |
| Деталь: | Decal:Caption:Interface:T-C |
| Парткод: | AA00 3039 |
| Деталь: | Sd-card:T-C1 :P/S:EXP:Assy |
| Парткод: | B157 5561 |
| Деталь: | Harness:Sensor:Front |
| Парткод: | B154 5405 |
| Деталь: | Harness:DC:Fusing:Machine Or Copier |
| Парткод: | B154 5428 |
| Деталь: | Harness:BICU:SCN |
| Парткод: | B154 5449 |
| Деталь: | Harness:BICU:ID |
| Парткод: | B154 5477 |
| Деталь: | Harness:FFC:LD |
| Парткод: | B154 5425 |
| Деталь: | Paper Tray:2nd:EXP:Assy |
| Парткод: | B156 2702 |
| Деталь: | Decal - Paper Set Direction |
| Парткод: | G070 2730 |
| Деталь: | Side Fence:Front:Assy |
| Парткод: | B154 2712 |
| Деталь: | Front Lever - Stopper |
| Парткод: | G070 2714 |
| Деталь: | Spring Plate Stopper |
| Парткод: | G070 2713 |
| Деталь: | Decal - OHP Paper Feed |
| Парткод: | B154 2583 |
| Деталь: | END FENCE |
| Парткод: | AF01 7025 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | AF01 1047 |
| Деталь: | Bottom Plate Pad |
| Парткод: | 52152713 |
| Деталь: | Spring - 5.9n/16.6n |
| Парткод: | AA06 3628 |
| Деталь: | Gear - 16Z |
| Парткод: | A267 2869 |
| Деталь: | Ground Plate- Bottom Plate |
| Парткод: | G0702719 |
| Деталь: | Base Stopper |
| Парткод: | G0702711 |
| Деталь: | LEVER SPRING |
| Парткод: | AA06 0866 |
| Деталь: | Side Fence:Rear:Assy |
| Парткод: | B154 2716 |
| Деталь: | Rear Lever - Stopper |
| Парткод: | G070 2718 |
| Деталь: | Decal - End Fence |
| Парткод: | B051 2581 |
| Деталь: | Joint - Feed Roller Shaft |
| Парткод: | G070 2728 |
| Деталь: | SPRING |
| Парткод: | AA06 3630 |
| Деталь: | Bushing - 8x12x10 |
| Парткод: | B039 2727 |
| Деталь: | GROUNDING PLATE |
| Парткод: | G070 2725 |
| Деталь: | Shaft:Paper Feed Roller:Assy |
| Парткод: | B154 2726 |
| Деталь: | Friction Pad:Assy |
| Парткод: | B154 2722 |
| Деталь: | Spring - 2.8n |
| Парткод: | AA06 3629 |
| Деталь: | Paper Feed Roller Mm36 |
| Парткод: | AF031084 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Paper Size Sensor Link |
| Парткод: | G070 2710 |
| Деталь: | Decal - Paper Tray |
| Парткод: | AA00 3022 |
| Деталь: | Paper Tray:2nd |
| Парткод: | AF01 0094 |
| Деталь: | Guide Plate - Side Fence |
| Парткод: | G070 2735 |
| Деталь: | Cooling Duct - Scanner Assembly |
| Парткод: | B051 5970 |
| Деталь: | Fan:Axial:MM80 |
| Парткод: | AX64 0166 |
| Деталь: | Stay:Guide Plate:Upper |
| Парткод: | B154 5871 |
| Деталь: | Tube:Pump-up |
| Парткод: | B154 4354 |
| Деталь: | Pump |
| Парткод: | B154 4358 |
| Деталь: | Oil Supply Tube |
| Парткод: | B051 4355 |
| Деталь: | Silicone Oil Nozzle |
| Парткод: | B051 4360 |
| Деталь: | Nozzle Bracket |
| Парткод: | B051 4359 |
| Деталь: | Bracket:CSS |
| Парткод: | B154 5864 |
| Деталь: | Harness:IOB:Gate |
| Парткод: | B154 5433 |
| Деталь: | Duct:Fan:Fusing:1 |
| Парткод: | B154 1296 |
| Деталь: | Stay:Guide Plate:Middle |
| Парткод: | B154 5873 |
| Деталь: | PCB:IOB |
| Парткод: | B154 5120 |
| Деталь: | Bracket: Base: I/O |
| Парткод: | B154 5862 |
| Деталь: | Fan:Sirocco:DC24V:Assy |
| Парткод: | B154 5845 |
| Деталь: | Bracket:Duct:Development:Exhaust |
| Парткод: | B154 5898 |
| Деталь: | Duct:Development:Exhaust:Front:Assy |
| Парткод: | B154 5846 |
| Деталь: | Duct:Development:Exhaust:Rear:Assy |
| Парткод: | B154 5847 |
| Деталь: | Cooling Duct - Right Development |
| Парткод: | B051 5846 |
| Деталь: | Cooling Duct - Left Development |
| Парткод: | B051 5845 |
| Деталь: | Duct:Fan:Fusing:2 |
| Парткод: | B1541297 |
| Деталь: | Nut:Damping Insulation Rubber:M4 |
| Парткод: | B154 5899 |
| Деталь: | Seal - Duct |
| Парткод: | B051 5965 |
| Деталь: | Shield:Duct:Exhaust:Fusing |
| Парткод: | B051 5964 |
| Деталь: | Harness:IOB:Main - 120V |
| Парткод: | B154 5402 |
| Деталь: | Harness:IOB:Main - 230V |
| Парткод: | B154 5403 |
| Деталь: | Harness:BICU-IOB |
| Парткод: | B154 5406 |
| Деталь: | Harness:IOB:Vertical Transport:24VS |
| Парткод: | B154 5408 |
| Деталь: | Harness:IOB:Intermediate Transfer |
| Парткод: | B154 5411 |
| Деталь: | Harness:IOB:Development:Fan |
| Парткод: | B154 5418 |
| Деталь: | Harness:Manual Feed:Machine or Copier |
| Парткод: | B154 5430 |
| Деталь: | Fusing Unit - 120V |
| Парткод: | B154 4026 |
| Деталь: | Fusing Unit - 230V |
| Парткод: | B154 4031 |
| Деталь: | Pickoff Pawl:Pressure Roller:Assy |
| Парткод: | B154 4010 |
| Деталь: | Knob Screw - 4m |
| Парткод: | B051 4103 |
| Деталь: | Oil Tank Packing |
| Парткод: | B051 4312 |
| Деталь: | Thermofuse - 131 C |
| Парткод: | G060 4351 |
| Деталь: | Decal - High Temperature Warning |
| Парткод: | AA00 0660 |
| Деталь: | Pickoff Pawl:pFA |
| Парткод: | AE04 4063 |
| Деталь: | Guide:Fusing Exit |
| Парткод: | B051 4146 |
| Деталь: | Front Cover - Fusing |
| Парткод: | B051 4108 |
| Деталь: | Shaft Support Plate |
| Парткод: | G070 4148 |
| Деталь: | Upper Cover - Fusing |
| Парткод: | B051 4101 |
| Деталь: | Guide Plate - Fusing Exit |
| Парткод: | G0704106 |
| Деталь: | Fusing Belt Upper Stay |
| Парткод: | G070 4221 |
| Деталь: | Stripper Pawl Spring |
| Парткод: | AA06 9263 |
| Деталь: | Front Electrode Plate |
| Парткод: | G070 4132 |
| Деталь: | Rearelectrode Plate |
| Парткод: | G070 4135 |
| Деталь: | Connecting Electrode Plate |
| Парткод: | G070 4141 |
| Деталь: | Fusing Unit Harness |
| Парткод: | B051 5424 |
| Деталь: | Rear Pressure Terminal Electrode |
| Парткод: | G070 4143 |
| Деталь: | Fusing Lower Cover |
| Парткод: | G070 4130 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Absorben - Lower Fusing Cover |
| Парткод: | G070 4138 |
| Деталь: | Spring Plate - Front Fusing Cover |
| Парткод: | G070 4136 |
| Деталь: | Spring Plate - Rear Fusing Cover |
| Парткод: | G070 4137 |
| Деталь: | Guide:Fusing Exit:Auxiliary:Both Ends |
| Парткод: | B051 4149 |
| Деталь: | Adsorben - Lower Center |
| Парткод: | G070 4157 |
| Деталь: | Absorben - Lower Front |
| Парткод: | G070 4159 |
| Деталь: | Absorben - Lower Rear |
| Парткод: | G070 4158 |
| Деталь: | Guide:Fusing Exit:Auxiliary |
| Парткод: | B051 4147 |
| Деталь: | Guide:Fusing Exit:Both Ends |
| Парткод: | B051 4148 |
| Деталь: | Stay:Guide Plate:Upper:Machine or Copier |
| Парткод: | B154 5870 |
| Деталь: | GRIP |
| Парткод: | B1541058 |
| Деталь: | Grip Bracket - Rear Light |
| Парткод: | B051 1134 |
| Деталь: | Gear - 40Z/42Z |
| Парткод: | AB01 7560 |
| Деталь: | Magnetic Clutch:0.4n M:Z32:Mm6 |
| Парткод: | AX20 0284 |
| Деталь: | Magnetic Clutch:0.4n M:Z46 |
| Парткод: | AX20 0283 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | Bracket - Magnetic Clutch1 |
| Парткод: | B051 4619 |
| Деталь: | Shaft:Feed:Drive:Assy |
| Парткод: | B154 4907 |
| Деталь: | Bracket - Magnetic Clutch2 |
| Парткод: | B051 4620 |
| Деталь: | Grip Bracket - Rear Left |
| Парткод: | B051 1133 |
| Деталь: | Gear - 44Z/28Z |
| Парткод: | AB01 7601 |
| Деталь: | Transfer/separation Receptacle |
| Парткод: | G070 6223 |
| Деталь: | Timing Belt - 120TS2M |
| Парткод: | AA04 3567 |
| Деталь: | Gear - 33Z/30T |
| Парткод: | AB01 7561 |
| Деталь: | Tightener:Paper Feed:Assy |
| Парткод: | B154 4908 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0869 |
| Деталь: | Stepper Motor:MM56:Assy |
| Парткод: | B154 4521 |
| Деталь: | Cushion:Stepper Motor |
| Парткод: | AA16 1164 |
| Деталь: | GEAR COVER |
| Парткод: | B051 1086 |
| Деталь: | Bracket:Drive:Paper Feed:Assy |
| Парткод: | B154 4615 |
| Деталь: | Gear - 58Z/37Z |
| Парткод: | AB01 7563 |
| Деталь: | Pulley - 33T/32Z |
| Парткод: | AB01 7600 |
| Деталь: | Timing Belt - 480TS3M |
| Парткод: | AA04 3568 |
| Деталь: | Timing Belt - S3M103T |
| Парткод: | AA04 3941 |
| Деталь: | Guide:Harness:Cl |
| Парткод: | B154 5880 |
| Деталь: | Cover:Front:Right Upper:T-C1 (NA/Asia) |
| Парткод: | B154 1205 |
| Деталь: | Cover:Front:Right Upper:T-C1:Assy (EU) |
| Парткод: | B1571205 |
| Деталь: | Paper Exit Cover - Sub Unit |
| Парткод: | B051 1300 |
| Деталь: | Front Cover - Scanner (NA/Asia) |
| Парткод: | B051 1345 |
| Деталь: | Cover:Scanner:Front (EU) |
| Парткод: | B1561345 |
| Деталь: | Caution Chart Decal - English |
| Парткод: | B051 1347 |
| Деталь: | Cover: Exit:Right |
| Парткод: | B156 1251 |
| Деталь: | Cover: Exit:Upper |
| Парткод: | B156 1252 |
| Деталь: | Decal:Grip:Exit |
| Парткод: | AA00 3023 |
| Деталь: | Cover: Exit |
| Парткод: | B1561250 |
| Деталь: | Exit Connecting Cover - Cap (NA/Asia) |
| Парткод: | B051 1255 |
| Деталь: | Cover:Exit:Connecting:Cap (EU) |
| Парткод: | B1561255 |
| Деталь: | Cover - Rear Exit (NA/Asia) |
| Парткод: | B051 1253 |
| Деталь: | Cover:Exit:Rear (EU) |
| Парткод: | B1561253 |
| Деталь: | Rear Exit Cover - Cap (NA/Asia) |
| Парткод: | B051 1254 |
| Деталь: | Cover:Exit:Rear:Cap (EU) |
| Парткод: | B156 1254 |
| Деталь: | Left Upper Cover (NA/Asia) |
| Парткод: | B051 1290 |
| Деталь: | Cover:Left Upper (EU) |
| Парткод: | B1561290 |
| Деталь: | Left Cover - Scanner (NA/Asia) |
| Парткод: | B051 1341 |
| Деталь: | Cover:Scanner:Left (EU) |
| Парткод: | B156 1341 |
| Деталь: | STEPPED SCREW |
| Парткод: | A1931759 |
| Деталь: | Decal:Power Source:Inkjet:Engllish |
| Парткод: | AA00 0663 |
| Деталь: | Exposure Glass:Sheet Through:332x14 |
| Парткод: | BC01 2001 |
| Деталь: | Scale:Machine or Copier:Assy (NA) |
| Парткод: | B386 7106 |
| Деталь: | Left Scale (EU) |
| Парткод: | B024 1680 |
| Деталь: | Exposure Glass |
| Парткод: | A2501752 |
| Деталь: | Inner Back Scale |
| Парткод: | B024 1701 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG07 0514 |
| Деталь: | Rear Cover - Scanner (NA/Asia) |
| Парткод: | B051 1340 |
| Деталь: | Cover:Scanner:Rear (EU) |
| Парткод: | B1561340 |
| Деталь: | Light Cover - Scanner (NA/Asia) |
| Парткод: | B051 1342 |
| Деталь: | Cover:Scanner:Right (EU) |
| Парткод: | B156 1342 |
| Деталь: | GUIDE PLATE |
| Парткод: | G070 2606 |
| Деталь: | RIGHT COVER |
| Парткод: | G0701357 |
| Деталь: | Rear Support Plate - Right Cover |
| Парткод: | G0701356 |
| Деталь: | SCREW |
| Парткод: | AA14 3493 |
| Деталь: | Right Link - Transport Cover |
| Парткод: | G070 1196 |
| Деталь: | Front Support Plate - Right Cover |
| Парткод: | G070 1354 |
| Деталь: | SPRING HOLDER |
| Парткод: | A232 1284 |
| Деталь: | SPRING |
| Парткод: | AA06 3402 |
| Деталь: | Un Lock Hook |
| Парткод: | G070 1361 |
| Деталь: | Decal:Grip:Vertical Transport |
| Парткод: | AA00 3024 |
| Деталь: | Light Lower Cover |
| Парткод: | G070 1284 |
| Деталь: | Rear Right Cover Hook |
| Парткод: | G0701353 |
| Деталь: | Pulley:Drive Were:Front:Sub-assy |
| Парткод: | B1801706 |
| Деталь: | Bushing - 8x12x7 |
| Парткод: | AA08 2104 |
| Деталь: | Drive Were:Carriage:Mm1.0 |
| Парткод: | AA05 0114 |
| Деталь: | Bracket:Tension |
| Парткод: | B1801704 |
| Деталь: | Tension Spring:Tension:11300mn |
| Парткод: | AA06 0980 |
| Деталь: | Front Left Bracket - Idler |
| Парткод: | B024 1841 |
| Деталь: | Rear Left Bracket - Idler |
| Парткод: | B024 1845 |
| Деталь: | Supporting Plate - Left Scanner |
| Парткод: | B051 1105 |
| Деталь: | Pulley - High Voltage Supply Cord |
| Парткод: | G570 2834 |
| Деталь: | Carriage:No.2:Assy |
| Парткод: | B1801723 |
| Деталь: | Xenon Lamp:DIA10.3:Assy |
| Парткод: | AX50 0085 |
| Деталь: | Wire Clamp |
| Парткод: | A1931766 |
| Деталь: | Carriage:No.1 :Assy |
| Парткод: | B180 1716 |
| Деталь: | Clamp - Rear Wire |
| Парткод: | A1931769 |
| Деталь: | Shielding Plate |
| Парткод: | B1801772 |
| Деталь: | Timing Belt:S1.5M236 |
| Парткод: | AA04 3966 |
| Деталь: | Timing Pulley 73 |
| Парткод: | G5701133 |
| Деталь: | Pulley:Drive Were:Rear:Sub-assy |
| Парткод: | B1801709 |
| Деталь: | Scanner Drive Shaft |
| Парткод: | G5701132 |
| Деталь: | Stepper Motor:Assy |
| Парткод: | B1541805 |
| Деталь: | Tension Spring:Tension:14720mn |
| Парткод: | AA06 0979 |
| Деталь: | IOB Scanner Bracket |
| Парткод: | B051 1802 |
| Деталь: | Rear Right Bracket - Scanner |
| Парткод: | B051 1114 |
| Деталь: | Front Right Bracket - Scanner |
| Парткод: | B051 1113 |
| Деталь: | Slide Rail:No.2 |
| Парткод: | B1801734 |
| Деталь: | 1st Slide Rail |
| Парткод: | A193 1816 |
| Деталь: | Spacer Bushing |
| Парткод: | G5701160 |
| Деталь: | Pulley Holder |
| Парткод: | G570 2833 |
| Деталь: | 2nd Mirror |
| Парткод: | G570 2826 |
| Деталь: | Spring Plate - 2nd Mirror |
| Парткод: | G404 2810 |
| Деталь: | Wire Pulley - M18 |
| Парткод: | A267 1855 |
| Деталь: | 1st Mirror |
| Парткод: | AC03 0142 |
| Деталь: | 1st Mirror Holder |
| Парткод: | A1931767 |
| Деталь: | Heater - 9W (120V) |
| Парткод: | A250 1821 |
| Деталь: | Heater - 9W (230V) |
| Парткод: | A2501822 |
| Деталь: | Guide - High Voltage Supply Cord |
| Парткод: | G570 2832 |
| Деталь: | Imaging Unit |
| Парткод: | B154 1852 |
| Деталь: | LD Unit Cover |
| Парткод: | G070 1971 |
| Деталь: | COVER |
| Парткод: | G070 1941 |
| Деталь: | Decal - LD 655 |
| Парткод: | AA00 0217 |
| Деталь: | Front Cover Shield |
| Парткод: | G070 1942 |
| Деталь: | Cylindical Lens |
| Парткод: | AC02 4005 |
| Деталь: | Sync Detector Holder |
| Парткод: | G070 1925 |
| Деталь: | Cover Bracket - LD Unit |
| Парткод: | G070 1972 |
| Деталь: | Sync Detector:Assy |
| Парткод: | B1541879 |
| Деталь: | Harness - LD Control Board-sync |
| Парткод: | B154 5342 |
| Деталь: | Harness:BICU:Imaging Unit |
| Парткод: | B154 5421 |
| Деталь: | FFC LD Harness |
| Парткод: | B051 5425 |
| Деталь: | Polygon Scanner |
| Парткод: | B1541975 |
| Деталь: | CLEANER |
| Парткод: | G0701955 |
| Деталь: | Cleaner Holder |
| Парткод: | G0701954 |
| Деталь: | Shield Glass Cover |
| Парткод: | G0701952 |
| Деталь: | Cleaner Shaft |
| Парткод: | G0701953 |
| Деталь: | Positioning Pin |
| Парткод: | G0701902 |
| Деталь: | Shield Glass |
| Парткод: | G0701903 |
| Деталь: | Cleaner Grip |
| Парткод: | G0701956 |
| Деталь: | Fusing Unit - 120V |
| Парткод: | B154 4026 |
| Деталь: | Fusing Unit - 230V |
| Парткод: | B154 4031 |
| Деталь: | Thermistor Holder |
| Парткод: | G070 4051 |
| Деталь: | Heater: 120V:770W |
| Парткод: | AX44 0233 |
| Деталь: | Heater:230V:770W |
| Парткод: | AX44 0234 |
| Деталь: | Heater: 120V:350W |
| Парткод: | AX43 0148 |
| Деталь: | Heater:230V:350W |
| Парткод: | AX43 0149 |
| Деталь: | Pressure Thermistor |
| Парткод: | AW10 0061 |
| Деталь: | Photointerruptor:Oil End Sensor |
| Парткод: | AW02 0164 |
| Деталь: | Fusing Knob |
| Парткод: | G070 4147 |
| Деталь: | Spring - Oiling Roller |
| Парткод: | AA06 3865 |
| Деталь: | Bushing -4x8x8.5 |
| Парткод: | AE03 1054 |
| Деталь: | Bushing -4x9x13 |
| Парткод: | AE031055 |
| Деталь: | Rubber Shield - 4x8x3 |
| Парткод: | G070 4087 |
| Деталь: | Gear - 36Z |
| Парткод: | AB01 1436 |
| Деталь: | BELT TENSION SPRING |
| Парткод: | AA06 0875 |
| Деталь: | Belt Tension Lever |
| Парткод: | G070 4116 |
| Деталь: | Front Stopper - Oil Supply Unit |
| Парткод: | G070 4114 |
| Деталь: | Sensor Holder |
| Парткод: | G070 4118 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Rear Stopper - Oil Supply Unit |
| Парткод: | G0704152 |
| Деталь: | Ball Bearing:20x32x7 |
| Парткод: | AE03 0062 |
| Деталь: | Pressure Roller - Assembly |
| Парткод: | AE02 0132 |
| Деталь: | Gear -47Z |
| Парткод: | AB01 1435 |
| Деталь: | Idler Gear - 28Z/35Z |
| Парткод: | AB01 7570 |
| Деталь: | Fusing Entrance Guide Plate |
| Парткод: | G070 4052 |
| Деталь: | Lower Pressure Roller Stay |
| Парткод: | G070 4050 |
| Деталь: | TENSION SPRING |
| Парткод: | AA06 0876 |
| Деталь: | Front Oil Tank Absorber |
| Парткод: | G070 4073 |
| Деталь: | Oil Tank - Pressure Sub-unit |
| Парткод: | G070 4069 |
| Деталь: | Rear Oil Pan - Pressure Unit |
| Парткод: | G070 4063 |
| Деталь: | Rear Oil Absorber |
| Парткод: | G070 4066 |
| Деталь: | Spring Plate - Pressure Unit |
| Парткод: | G070 4064 |
| Деталь: | Front Oil Pan - Pressure Unit |
| Парткод: | G070 4062 |
| Деталь: | Front Oil Absorber |
| Парткод: | G070 4065 |
| Деталь: | Oil Tank Absorber - Long |
| Парткод: | G070 4074 |
| Деталь: | Oil Supply Roller - Oil Supply |
| Парткод: | AE04 0048 |
| Деталь: | Oil Apply Roller - Oil Supply |
| Парткод: | AE04 0047 |
| Деталь: | Heat Insulation - Sensor Holder |
| Парткод: | G070 4120 |
| Деталь: | Front Oil Tank Absorber |
| Парткод: | G070 4072 |
| Деталь: | Roller Clutch - 4mm |
| Парткод: | B051 4138 |
| Деталь: | Cleaning Roller:Pressure Sub-unit |
| Парткод: | B154 4119 |
| Деталь: | Bushing - Cleaning Roller |
| Парткод: | B051 4116 |
| Деталь: | Torsion Spring - Rear |
| Парткод: | B051 4118 |
| Деталь: | Torsion Spring - Front |
| Парткод: | B051 4120 |
| Деталь: | Side Plate:Pressure Sub-unit:Front:Peen |
| Парткод: | B154 4116 |
| Деталь: | Side Plate:Pressure Sub-unit:Rear:Peen |
| Парткод: | B154 4107 |
| Деталь: | STOPPER SPRING |
| Парткод: | G070 4153 |
| Деталь: | Fusing Unit:Fusing Belt:Assy |
| Парткод: | B154 4009 |
| Деталь: | Paper Tray:EXP:Assy |
| Парткод: | B156 2701 |
| Деталь: | Decal - Paper Set Direction |
| Парткод: | G070 2730 |
| Деталь: | Side Fence:Front:Assy |
| Парткод: | B154 2712 |
| Деталь: | Front Lever - Stopper |
| Парткод: | G070 2714 |
| Деталь: | Spring Plate Stopper |
| Парткод: | G070 2713 |
| Деталь: | Decal - OHP Paper Feed |
| Парткод: | B154 2583 |
| Деталь: | END FENCE |
| Парткод: | AF01 7025 |
| Деталь: | TRAY BOTTOM PLATE |
| Парткод: | AF01 1047 |
| Деталь: | Bottom Plate Pad |
| Парткод: | 52152713 |
| Деталь: | Spring - 5.9n/16.6n |
| Парткод: | AA06 3628 |
| Деталь: | Gear - 16Z |
| Парткод: | A267 2869 |
| Деталь: | Ground Plate- Bottom Plate |
| Парткод: | G0702719 |
| Деталь: | Base Stopper |
| Парткод: | G0702711 |
| Деталь: | LEVER SPRING |
| Парткод: | AA06 0866 |
| Деталь: | Side Fence:Rear:Assy |
| Парткод: | B154 2716 |
| Деталь: | Rear Lever - Stopper |
| Парткод: | G070 2718 |
| Деталь: | Decal - End Fence |
| Парткод: | B051 2581 |
| Деталь: | Joint - Feed Roller Shaft |
| Парткод: | G070 2728 |
| Деталь: | SPRING |
| Парткод: | AA06 3630 |
| Деталь: | Bushing - 8x12x10 |
| Парткод: | B039 2727 |
| Деталь: | GROUNDING PLATE |
| Парткод: | G070 2725 |
| Деталь: | Shaft:Paper Feed Roller:Assy |
| Парткод: | B154 2726 |
| Деталь: | Friction Pad:Assy |
| Парткод: | B154 2722 |
| Деталь: | Spring - 2.8n |
| Парткод: | AA06 3629 |
| Деталь: | Paper Feed Roller Mm36 |
| Парткод: | AF031084 |
| Деталь: | Snap Ring - M6 |
| Парткод: | 52 152 621 |
| Деталь: | Paper Size Sensor Link |
| Парткод: | G070 2710 |
| Деталь: | Decal - Paper Tray |
| Парткод: | AA00 3022 |
| Деталь: | Guide Plate - Side Fence |
| Парткод: | G070 2735 |
| Деталь: | Connector:Manual Feed:Machine or Copier |
| Парткод: | B051 5434 |
| Деталь: | Connector bracket |
| Парткод: | B051 5874 |
| Деталь: | Bracket:Temperature & Humidity Sensor |
| Парткод: | B154 5863 |
| Деталь: | Temperature & Humidity Sensor |
| Парткод: | AW14 0012 |
| Деталь: | Fan:Sirocco:DC24V:Assy |
| Парткод: | B154 5849 |
| Деталь: | Stay:Guide Plate:Lower |
| Парткод: | B051 5867 |
| Деталь: | Bracket - Power Supply Cord |
| Парткод: | B051 5866 |
| Деталь: | Power Supply Cord - 120V |
| Парткод: | B154 5475 |
| Деталь: | Power Supply Cord - 230V |
| Парткод: | B154 5476 |
| Деталь: | Roller Terminal - Oil Supply |
| Парткод: | G070 4314 |
| Деталь: | SPRING |
| Парткод: | AA06 3895 |
| Деталь: | Oil Supply Roller Holder |
| Парткод: | G070 4320 |
| Деталь: | Stay:Duct:Exhaust:Small |
| Парткод: | B154 5892 |
| Деталь: | Terminal Cover - Oil Supply Roller |
| Парткод: | G070 4316 |
| Деталь: | Roller Holder - Oil Supply |
| Парткод: | G070 4313 |
| Деталь: | Plate:Cable |
| Парткод: | B154 5879 |
| Деталь: | Harness:AC:Fusing:Machine Or Copier |
| Парткод: | B154 5427 |
| Деталь: | Connector bracket |
| Парткод: | G070 4310 |
| Деталь: | Harness:Power Supply Unit:Output |
| Парткод: | B154 5414 |
| Деталь: | Harness:DC:Fusing:Machine Or Copier |
| Парткод: | B154 5428 |
| Деталь: | Power Supply Unit:T-C1 - 120V |
| Парткод: | AZ240100 |
| Деталь: | Power Supply Unit:T-C1 - 230V |
| Парткод: | AZ240101 |
| Деталь: | Fcc Cover |
| Парткод: | B051 1131 |
| Деталь: | Oil Tank Lower Bracket |
| Парткод: | B051 4353 |
| Деталь: | Bracket - Rear Lower Cover |
| Парткод: | B051 1331 |
| Деталь: | Stay:Contact Point:Lower |
| Парткод: | B154 5876 |
| Деталь: | Stay:Contact Point:Upper |
| Парткод: | B154 5875 |
| Деталь: | TUBE |
| Парткод: | B154 4356 |
| Деталь: | Oil Tank Bracket |
| Парткод: | B051 4352 |
| Деталь: | Stay:Duct:Exhaust |
| Парткод: | B154 5893 |
| Деталь: | Oil Tank |
| Парткод: | B051 4351 |
| Деталь: | Duct - Upper Charge |
| Парткод: | B051 5894 |
| Деталь: | Duct Shield |
| Парткод: | G070 1083 |
| Деталь: | Duct - Lower Charge |
| Парткод: | B051 5892 |
| Деталь: | Nut:Damping Insulation Rubber:M4 |
| Парткод: | B154 5899 |
| Деталь: | Cap - Oil Tank Assembly |
| Парткод: | B051 4361 |
| Деталь: | Harness:Dehumidifier |
| Парткод: | B154 5467 |
| Деталь: | Harness:Leak Breaker |
| Парткод: | B154 5466 |
| Деталь: | Fly Wheel:MM140 |
| Парткод: | B154 4732 |
| Деталь: | DRIVE UNIT |
| Парткод: | B154 4700 |
| Деталь: | Pin - Intermediate Transfer |
| Парткод: | G070 4728 |
| Деталь: | Magnetic Clutch:Development:BK |
| Парткод: | AX21 0094 |
| Деталь: | Brushless Motor:26W:9Z |
| Парткод: | AX06 0291 |
| Деталь: | Bracket:Drive:Development:Assy |
| Парткод: | B154 4611 |
| Деталь: | Idler Gear - 67Z |
| Парткод: | AB01 0353 |
| Деталь: | Gear - 93Z/42Z |
| Парткод: | AB01 7565 |
| Деталь: | Guide Plate:Harness |
| Парткод: | B154 5867 |
| Деталь: | Guide Plate:Harness:Development |
| Парткод: | B154 5866 |
| Деталь: | Brushless Motor:8.8W:9Z |
| Парткод: | AX06 0319 |
| Деталь: | BALL BEARING |
| Парткод: | G070 4721 |
| Деталь: | Compression Spring:Joint |
| Парткод: | AA06 3632 |
| Деталь: | Inner Joint |
| Парткод: | G070 4768 |
| Деталь: | Middle Joint |
| Парткод: | G070 4767 |
| Деталь: | Outer Joint |
| Парткод: | G070 4766 |
| Деталь: | Shaft:Drive:Intermediate Transfer |
| Парткод: | AA14 9883 |
| Деталь: | Feeler - Paper Overflow |
| Парткод: | A267 4478 |
| Деталь: | Overflow Shaft |
| Парткод: | G070 4472 |
| Деталь: | Discharge Brush |
| Парткод: | AA120103 |
| Деталь: | BUSHING - 6X10X6 |
| Парткод: | AA08 2101 |
| Деталь: | Transport Exit Roller |
| Парткод: | AF02 0545 |
| Деталь: | Feeler - Paper Feed Sensor |
| Парткод: | A267 4476 |
| Деталь: | PUSH SWITCH |
| Парткод: | AW50 0023 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Exit Guide Plate |
| Парткод: | G070 4455 |
| Деталь: | Edit Grounding Plate |
| Парткод: | G070 4458 |
| Деталь: | Gear - 19Z |
| Парткод: | AB01 1229 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0567 |
| Деталь: | Spring Plate - Outer Tension Roller |
| Парткод: | G070 4466 |
| Деталь: | Tension Roller |
| Парткод: | AF04 0566 |
| Деталь: | Spring Plate - Tension Roller |
| Парткод: | G070 4461 |
| Деталь: | Idle Roller |
| Парткод: | G047 4785 |
| Деталь: | Roller - 9mm |
| Парткод: | G070 4459 |
| Деталь: | Fusing Exit Roller |
| Парткод: | AF02 0624 |
| Деталь: | Guide Plate - Fusing Exit |
| Парткод: | G070 4481 |
| Деталь: | Bracket - Fusing Exit Feeler |
| Парткод: | G070 4477 |
| Деталь: | Spring - Fusing Exit Feeler |
| Парткод: | G070 4478 |
| Деталь: | Fusing Exit Feeler |
| Парткод: | G070 4476 |
| Деталь: | Harness:Fusing Exit:Connecting |
| Парткод: | B051 5403 |
| Деталь: | Sensor Bracket - Fusing Exit |
| Парткод: | G070 4486 |
| Деталь: | Discharge Brush |
| Парткод: | AA12 0113 |
| Деталь: | Grounding Plate - Fusing Exit |
| Парткод: | G070 4492 |
| Деталь: | Gear - 14Z |
| Парткод: | AB01 1230 |
| Деталь: | Bracket:Drive:Exit |
| Парткод: | B154 4920 |
| Деталь: | Gear - 27Z |
| Парткод: | AB01 1425 |
| Деталь: | DRIVEN ROLLER |
| Парткод: | AF02 2112 |
| Деталь: | Paper Feed Sensor |
| Парткод: | AW02 0160 |
| Деталь: | Decal Warning (High Temperature) |
| Парткод: | AA00 0301 |
| Деталь: | Clip:Discharge Brush |
| Парткод: | G070 4462 |
| Деталь: | Oil Application Unit:Assy |
| Парткод: | B154 4300 |
| Деталь: | Cover - Oil Supply Unit |
| Парткод: | B051 4301 |
| Деталь: | PRESSURE SPRING |
| Парткод: | AA06 0915 |
| Деталь: | Felt Wick:Assy |
| Парткод: | B154 4302 |
| Деталь: | Oil Tank - Oil Application Unit |
| Парткод: | B051 4305 |
| Деталь: | Holder - Oil Tank |
| Парткод: | G070 4212 |
| Деталь: | Positioning Sensor - Overflow |
| Парткод: | B154 4306 |
| Деталь: | Dual Faces Tepe |
| Парткод: | B051 4307 |
| Деталь: | Sponge Roller |
| Парткод: | G070 4217 |
| Деталь: | SPRING |
| Парткод: | AA06 3882 |
| Деталь: | Bushing - Sponge Roller |
| Парткод: | G070 4219 |
| Деталь: | Spring - Fusing Cleaning Roller |
| Парткод: | AA06 0880 |
| Деталь: | Bracket Assembly |
| Парткод: | B154 4320 |
| Деталь: | Spring Plate - Tension Roller |
| Парткод: | B051 4309 |
| Деталь: | Roller - Oil Supply Roller |
| Парткод: | G070 4231 |
| Деталь: | Fusing Cleaning Roller:DIA10 |
| Парткод: | B154 4218 |
| Деталь: | Bushing - 4x6x5.5 |
| Парткод: | G070 4220 |
| Деталь: | Shoulder Screw - M3 |
| Парткод: | 52 062 684 |
| Деталь: | Oil Tank Guide |
| Парткод: | B051 4319 |
| Деталь: | Cleaning Roller Cover |
| Парткод: | G070 4225 |
| Деталь: | Bracket Pin - Rear |
| Парткод: | AA14 9957 |
| Деталь: | Bracket - Fusing Cleaning Roller |
| Парткод: | G070 4216 |
| Деталь: | Bracket - Fusing Sponge Roller |
| Парткод: | G070 4204 |
| Деталь: | Bracket Pin - Front |
| Парткод: | AA14 9956 |
| Деталь: | Spacer:Oil Tank |
| Парткод: | B051 4311 |
| Деталь: | Right Cover - Vertical Transport |
| Парткод: | B051 1359 |
| Деталь: | Transfer Unit Stopper |
| Парткод: | G070 6221 |
| Деталь: | SPRING |
| Парткод: | AA06 3563 |
| Деталь: | BUSHING - M4 |
| Парткод: | AA08 0254 |
| Деталь: | Roller:Driven:Assy |
| Парткод: | B154 2862 |
| Деталь: | Transfer Unit Spring -10n |
| Парткод: | AA06 3876 |
| Деталь: | Registration Driven Cleaner |
| Парткод: | G070 2585 |
| Деталь: | Right Cover Guide - By-pass Feed |
| Парткод: | G070 1281 |
| Деталь: | Spring - 20n |
| Парткод: | AA06 3631 |
| Деталь: | Bushing - Driven Roller |
| Парткод: | A267 2685 |
| Деталь: | Sensor Seal - 22x39.5 |
| Парткод: | B154 6235 |
| Деталь: | Registration Roller:Driven:MM14 |
| Парткод: | AF02 1082 |
| Деталь: | Right Guide Plate |
| Парткод: | G070 2583 |
| Деталь: | Shield:Guide Plate |
| Парткод: | G070 2586 |
| Деталь: | Entrance Guide |
| Парткод: | G070 6245 |
| Деталь: | TRANSFER ROLLER |
| Парткод: | B154 6200 |
| Деталь: | Roller - Transfer Roller |
| Парткод: | G070 6201 |
| Деталь: | Collar - 8x11x10 |
| Парткод: | G070 6236 |
| Деталь: | Transfer Roller Bushing |
| Парткод: | G070 6202 |
| Деталь: | Transfer Roller Holder |
| Парткод: | G070 6206 |
| Деталь: | Transport Guide Assembly |
| Парткод: | B051 6231 |
| Деталь: | Wire:Bias:Separation |
| Парткод: | B154 5456 |
| Деталь: | Arm:Assy |
| Парткод: | B154 6237 |
| Деталь: | Transfer Unit Frame |
| Парткод: | G070 6204 |
| Деталь: | Transfer Unit Spring - 16n |
| Парткод: | AA06 3896 |
| Деталь: | Ground Wire:Arm:Transfer |
| Парткод: | B154 5457 |
| Деталь: | Rear Grounding Plate |
| Парткод: | G070 6210 |
| Деталь: | Transfer Roller Terminal |
| Парткод: | G070 6218 |
| Деталь: | Terminal Cover Sheet |
| Парткод: | B051 6243 |
| Деталь: | Frame Stay |
| Парткод: | G070 6205 |
| Деталь: | Front Transfer Guide |
| Парткод: | B051 1365 |
| Деталь: | Separation Terminal |
| Парткод: | G070 6220 |
| Деталь: | Ground Plate:Registration |
| Парткод: | G070 2592 |
| Деталь: | Holder:Resistor |
| Парткод: | G070 2591 |
| Деталь: | Electrode Plate:Registration |
| Парткод: | G070 2593 |
| Деталь: | Holder:Resistor:Assy |
| Парткод: | G070 2590 |
| Деталь: | Terminal Cover - Doctor Blade |
| Парткод: | G070 3293 |
| Деталь: | Doctor Blade Terminal |
| Парткод: | G070 3291 |
| Деталь: | Doctor Blade Terminal |
| Парткод: | G070 3292 |
| Деталь: | PCB:Toner End Sensor:Rear:Photo |
| Парткод: | B154 5270 |
| Деталь: | Damper Cover |
| Парткод: | G070 3237 |
| Деталь: | Damper - Development Roller |
| Парткод: | G070 3248 |
| Деталь: | Side Plate:Rear:Development |
| Парткод: | B154 3232 |
| Деталь: | COMPRESSION SPRING |
| Парткод: | G070 3239 |
| Деталь: | Spring Cap |
| Парткод: | G070 3240 |
| Деталь: | Color Shaft - Development |
| Парткод: | G070 4605 |
| Деталь: | Harness:Development:Sponge:Roller |
| Парткод: | B154 5463 |
| Деталь: | Harness - ID Sensor Board |
| Парткод: | G070 5285 |
| Деталь: | Bias Terminal Cover |
| Парткод: | G070 3295 |
| Деталь: | Front Side Plate |
| Парткод: | G070 3231 |
| Деталь: | Development Vias Terminal |
| Парткод: | G070 3236 |
| Деталь: | PCB:ID:Assy |
| Парткод: | B154 5281 |
| Деталь: | Harness:PPI:High Voltage Line:B2 |
| Парткод: | B154 5453 |
| Деталь: | Stay:Left Lower:Assy |
| Парткод: | B1541068 |
| Деталь: | PCB:Toner End Sensor:Front:Radiate |
| Парткод: | B154 5260 |
| Деталь: | Side Plate - Front Left |
| Парткод: | G070 3233 |
| Деталь: | Display Decal - Magenta |
| Парткод: | G024 6992 |
| Деталь: | Display Decal - Cyan |
| Парткод: | G024 6991 |
| Деталь: | Display Decal - Yellow |
| Парткод: | G024 6993 |
| Деталь: | Display Decal - Black |
| Парткод: | G024 6994 |
| Деталь: | Front Lower Middle Shield |
| Парткод: | G0701093 |
| Деталь: | Shaft:Development:On-Off:FC |
| Парткод: | B154 4607 |
| Деталь: | Development Unit - BK |
| Парткод: | B154 0152 |
| Деталь: | O/O |
| Парткод: | B154 0157 |
| Деталь: | Development Unit - M |
| Парткод: | B154 0154 |
| Деталь: | O/O |
| Парткод: | B154 0158 |
| Деталь: | Development Unit - Y |
| Парткод: | B154 0156 |
| Деталь: | O/O |
| Парткод: | B154 0160 |
| Деталь: | Development Unit - C |
| Парткод: | B154 0155 |
| Деталь: | O/O |
| Парткод: | B154 0161 |
| Деталь: | BUSHING |
| Парткод: | G024 1473 |
| Деталь: | Rubber Foot - 23mm |
| Парткод: | G024 1007 |
| Деталь: | Lower Shield - Front Left |
| Парткод: | G070 1094 |
| Деталь: | Arm - Scanner |
| Парткод: | B051 1104 |
| Деталь: | Lower Shield - PCU Rail |
| Парткод: | G0701092 |
| Деталь: | PCU Lower Rail |
| Парткод: | G070 2372 |
| Деталь: | Upper Supporting Stay |
| Парткод: | B051 2368 |
| Деталь: | PCU Rail Seal - 9x19x5 |
| Парткод: | G0701105 |
| Деталь: | PCU Rail Seal - 3x30x5 |
| Парткод: | G0701104 |
| Деталь: | PCU Upper Rail |
| Парткод: | G070 2371 |
| Деталь: | DENSITY SENSOR |
| Парткод: | AW01 0097 |
| Деталь: | On/off Rail |
| Парткод: | G070 6405 |
| Деталь: | Grounding Plate - Belt Cleaning |
| Парткод: | G070 6406 |
| Деталь: | Frame - Right Front Upper |
| Парткод: | B051 1076 |
| Деталь: | Stay - Right Upper Assembly |
| Парткод: | B051 1102 |
| Деталь: | Light Midle Stay |
| Парткод: | B051 1101 |
| Деталь: | Fusing Unit Rail |
| Парткод: | G070 4302 |
| Деталь: | Rail:Fusing:Machine or Copier |
| Парткод: | B154 1076 |
| Деталь: | Right Rail Shoe |
| Парткод: | G070 2622 |
| Деталь: | Rail:Right:Assy |
| Парткод: | B154 2620 |
| Деталь: | Grounding Plate Bracket |
| Парткод: | G070 6227 |
| Деталь: | Charge Ground Plate |
| Парткод: | G070 2135 |
| Деталь: | Rear Left Frame - Lengthwise |
| Парткод: | B051 1091 |
| Деталь: | Rear Upper Frame |
| Парткод: | B051 1093 |
| Деталь: | Connector Gate Bracket |
| Парткод: | B051 1126 |
| Деталь: | Rear Right Frame - Lengthwise |
| Парткод: | B051 1092 |
| Деталь: | Bracket:Sensor:Intermediate Transfer Belt |
| Парткод: | B154 6420 |
| Деталь: | Photointerruptor:Flat |
| Парткод: | AW02 0145 |
| Деталь: | Paper Feed Sensor:Fusing Exit |
| Парткод: | AW01 0061 |
| Деталь: | Cover:Sensor |
| Парткод: | B154 4290 |
| Деталь: | Rail Spacer - 18.5x19.5x3.3 |
| Парткод: | B051 4370 |
| Деталь: | Stopper:Arm |
| Парткод: | B154 1086 |
| Деталь: | Door:Front (NA/Asia) |
| Парткод: | B156 1259 |
| Деталь: | Door:Front (EU) |
| Парткод: | B1541250 |
| Деталь: | Cover - Main Switch |
| Парткод: | B051 1360 |
| Деталь: | Model Name Plate:T-C1b:Ricoh (24) |
| Парткод: | B156 7520 |
| Деталь: | Model Name Plate:T-C1b:Savin (24) |
| Парткод: | B156 7521 |
| Деталь: | Model Name Plate:T-C1b:GES (24) |
| Парткод: | B156 7522 |
| Деталь: | Model Name Plate:T-C1b:LAN (24) |
| Парткод: | B156 7523 |
| Деталь: | Model Name Plate:T-C1b:INF (24) |
| Парткод: | B156 7524 |
| Деталь: | Model Name Plate:T-C1b:NRG:NSA (24)(EU) |
| Парткод: | B156 7525 |
| Деталь: | Model Name Plate:T-C1b:NRG:REX (24)(EU) |
| Парткод: | B156 7526 |
| Деталь: | Model Name Plate:T-C1b:NRG:GES (24)(EU) |
| Парткод: | B156 7527 |
| Деталь: | Model Name Plate:T-C1c:Ricoh (32) |
| Парткод: | B220 7520 |
| Деталь: | Model Name Plate:T-C1c:Savin (32) |
| Парткод: | B220 7521 |
| Деталь: | Model Name Plate:T-C1c:GES (32) |
| Парткод: | B220 7522 |
| Деталь: | Model Name Plate:T-C1c:LAN (32) |
| Парткод: | B220 7523 |
| Деталь: | Model Name Plate:T-C1c:INF (32) |
| Парткод: | B220 7524 |
| Деталь: | Model Name Plate:T-C1c:NRG:NAS (32)(EU) |
| Парткод: | B220 7525 |
| Деталь: | Model Name Plate:T-C1c:NRG:REX (32)(EU) |
| Парткод: | B220 7526 |
| Деталь: | Model Name Plate:T-C1c:NRG:GES (32)(EU |
| Парткод: | B220 7527 |
| Деталь: | Decal - Power Source |
| Парткод: | G070 9531 |
| Деталь: | Hinge pin |
| Парткод: | A166 1363 |
| Деталь: | Magnet Catich - Front Cover |
| Парткод: | G070 1253 |
| Деталь: | Sheet:Operate:T-C1 :EXP |
| Парткод: | B220 1394 |
| Деталь: | Decal - Inner Cover |
| Парткод: | A2591522 |
| Деталь: | Inner Right Lower Cover |
| Парткод: | B051 1371 |
| Деталь: | Development Inner Cover |
| Парткод: | G0701375 |
| Деталь: | Decal - Paper Tray |
| Парткод: | GA00 3014 |
| Деталь: | Holder:Operating Instructions |
| Парткод: | B154 8521 |
| Деталь: | LEFT INNER COVER |
| Парткод: | G0701370 |
| Деталь: | Magnet Catch:Assy |
| Парткод: | AG07 0514 |
| Деталь: | Left Cover (NA/Asia) |
| Парткод: | B051 1280 |
| Деталь: | Cover:Left (EU) |
| Парткод: | B1561280 |
| Деталь: | Stepped Screw - M6x1.7 |
| Парткод: | C105 2352 |
| Деталь: | Development Unit Cover (NA/Asia) |
| Парткод: | G0701290 |
| Деталь: | Cover:Exterior:Development Unit (EU) |
| Парткод: | B1561390 |
| Деталь: | Cover:Rear (NA/Asia) |
| Парткод: | B154 1310 |
| Деталь: | Cover:Rear (EU) |
| Парткод: | B156 1310 |
| Деталь: | Rivet - M7 |
| Парткод: | B0391364 |
| Деталь: | Cover:Oil Tank (NA/Asia) |
| Парткод: | B1541322 |
| Деталь: | Cover:Oil Tank (EU) |
| Парткод: | B1561322 |
| Деталь: | Operating Instructions:System:RIC:NA:Englis |
| Парткод: | B156 7505 |
| Деталь: | Operating Instructions:System:RIC:AA:Englis |
| Парткод: | B156 7540 |
| Деталь: | Filter:Exhaust:Scanner |
| Парткод: | AA01 2125 |
| Деталь: | Rear Filter Cover - Development (NA/Asia) |
| Парткод: | B051 1317 |
| Деталь: | Cover:Filter:Rear:Development (EU) |
| Парткод: | B156 1317 |
| Деталь: | Filter:Exhaust |
| Парткод: | AA01 2123 |
| Деталь: | Rear Small Cover - Filter (NA/Asia) |
| Парткод: | B051 1326 |
| Деталь: | Cover:Filter:Rear:Small (EU) |
| Парткод: | B1561326 |
| Деталь: | Rear Cover - Cap (NA/Asia) |
| Парткод: | B051 1316 |
| Деталь: | Cover:Rear:Cap (EU) |
| Парткод: | B156 1316 |
| Деталь: | Rear Filter Cover (NA/Asia) |
| Парткод: | B051 1320 |
| Деталь: | Cover:Filter:Rear (EU) |
| Парткод: | B1561320 |
| Деталь: | Sound Proofing - Cover Filter |
| Парткод: | G0701077 |
| Деталь: | Seal - Filter Cover |
| Парткод: | B051 1324 |
| Деталь: | Seal - Filter Cover |
| Парткод: | B051 1328 |
| Деталь: | Filter Cover (NA/Asia) |
| Парткод: | B051 1323 |
| Деталь: | Cover:Filter:Maintenance (EU) |
| Парткод: | B1561323 |
| Деталь: | Filter:Duct:Exhaust |
| Парткод: | AA01 2124 |
| Деталь: | OZONE FILTER |
| Парткод: | AA01 0113 |
| Деталь: | Rear Cover - Duplex (NA/Asia) |
| Парткод: | B051 1315 |
| Деталь: | Cover:Rear:Duplex (EU) |
| Парткод: | B156 1315 |
| Деталь: | Cover:Rear Lower:DOM (NA/Asia) |
| Парткод: | B154 1311 |
| Деталь: | Cover:Rear Lower (EU) |
| Парткод: | B156 1311 |
| Деталь: | Lower Cover - Fan Motor |
| Парткод: | B051 1325 |
| Деталь: | Cover:Right Rear (NA/Asia) |
| Парткод: | B1541270 |
| Деталь: | Cover:Right Rear (EU) |
| Парткод: | B1561270 |
| Деталь: | Gate Cap (NA/Asia) |
| Парткод: | B051 1271 |
| Деталь: | Cap:Gate (EU) |
| Парткод: | B156 1271 |
| Деталь: | Duplex Small Cap |
| Парткод: | G0701262 |
| Деталь: | Rear Cap - Duplex (NA/Asia) |
| Парткод: | B051 1380 |
| Деталь: | Cap:Duplex:Rear (EU) |
| Парткод: | B1561380 |
| Деталь: | Duplex Cap |
| Парткод: | G0701261 |
| Деталь: | Right Front Cover (NA/Asia) |
| Парткод: | B051 1260 |
| Деталь: | Cover:Right Front (EU) |
| Парткод: | B1561260 |
| Деталь: | Operating Instructions:Copy:RIC:NA:English |
| Парткод: | B156 7509 |
| Деталь: | Operating Instructions:Copy:RIC:AA:English |
| Парткод: | B156 7541 |
| Деталь: | Operating Instructions:Printer:English(NA/Asia) |
| Парткод: | B156 7551 |
| Деталь: | Operating Instructions:Security:English(NA/Asia) |
| Парткод: | B156 7571 |
| Деталь: | Panel:Logo |
| Парткод: | B132 1531 |
| Деталь: | Gap Absorber Seal - 10x18x4 |
| Парткод: | B051 1273 |
| Деталь: | Damper:Cover:Exterior:Development Unit |
| Парткод: | B154 1291 |
| Деталь: | Cap:Grip |
| Парткод: | B1541053 |
| Деталь: | Decal:Misfeed Removal:Exit |
| Парткод: | AA00 3025 |
| Деталь: | Cloth Holder |
| Парткод: | B065 1371 |
| Деталь: | Cloth - DF Exposure Glass |
| Парткод: | B065 1374 |
| Деталь: | Decal:Color:Mfp |
| Парткод: | AA00 0239 |
Коды ошибок
101
120
121
142
144
161
195
199
201
220
221
230
231
241
280
282
300
302
305
350
352
353
401
410
411
412
420
421
430
440
460
461
480
481
503
504
515
520
521
530
541
542
543
544
545
546
547
551
552
553
554
555
556
557
570
571
572
620
630
632
633
634
635
640
641
670
672
685
687
720
722
724
725
726
727
728
730
731
732
740
750
770
791
792
793
800
801
802
803
804
805
806
807
808
809
810
818
819
820
821
822
823
824
826
827
828
829
835
836
837
838
850
851
853
854
855
856
860
861
862
863
864
865
870
880
900
901
902
925
990
991
995
997
998
999
Описание
| Error code: | 101 |
| Description: | Replace Maintenance Kit The Printer detected an error condition that indicates the parts listed below need to be replaced. This will ensure the rated engine life of 600,000 prints is achievable. |
| Causes: | • Long-Life Maintenance Kit, 650-4360-00 |
| Remedy: | 1 Follow the procedure starting and replace all concerned parts. Have all parts outlined in the procedure been replaced? Go to the Hidden Service menu on the Control Panel and Reset the Maintenance Kit Life count. Replace all concerned parts. |
| Error code: | 120 |
| Display: | Service Call 120: Error |
| Description: | Fuser Error |
| Causes: | 1) Is fan in PU unit operating? 2) Error reoccurs after replacing fan motor. |
| Remedy: | Wrong fuser lamp - hot roll - replace the fuser assembly. See “Fuser assembly” |
| Error code: | 121 |
| Display: | Service Call 121: Error |
| Description: | Fuser Error |
| Causes: | Is cable between PU board andhighvoltage power LSI connected properly? |
| Remedy: | Wrong fuser lamp - BUR - replace the fuser assembly |
| Error code: | 142 |
| Display: | Contact the Service center. 142: Error |
| Description: | Motor |
| Causes: | • Standard white plate defective, dirty • Moisture inside the scanner unit • SBU to IPU harnesses defective • BCU to IPU harnesses defective • SBU defective • IPU defective • BCU defective |
| Remedy: | DC pick motor, over speed - staging motor - replace the “Staging motor”. If this does not fix the problem, replace the “System board”. |
| Error code: | 144 |
| Display: | ERROR 144 CARTRIDGE SET ! |
| Description: | Motor |
| Causes: | • SBU defective • BCU defective • Harness between SBU and IPU defective |
| Remedy: | DC motor accel stall - autocompensator motor - replace the “Autocompensator pick assembly” on page 4-24. If this does not fix the problem, replace the “System board” on page 4-80. |
| Error code: | 161 |
| Display: | SYSTEM HALT (*) 161 : PCB MAIN-F6 |
| Description: | IPU Error At power on, or when the machine returns from an energy save mode, the self-diagnostic program returned an IPU error. |
| Causes: | • IPU defective • Connection between SBU and IPU is loose, broken, or defective |
| Error code: | 195 |
| Description: | Serial Number Error |
| Causes: | The serial number stored in the memory (EGB) is not correct. |
| Remedy: | EEPROM defective EGB replaced without original EEPROM |
| Error code: | 199 |
| Description: | Service Reflash RIP |
| Causes: | • ADF interface cable defective • SBCU board defective • Mismatched firmware between the SBCU board and ADF |
| Remedy: | The printer has detected an invalid version of the RIP code and must be reflashed to the approved version. Contact your next level support. |
| Error code: | 201 |
| Display: | ERROR 201 COMMAND |
| Description: | PU F/W Flash write error (Reserved) |
| Causes: | • Defective polygon motor • Defective harness |
| Remedy: | 1. Connect the cable correctly. 2. Replace the engine control board. 3. Replace the laser scanning unit. 4. Check or replace the cable. |
| Error code: | 220 |
| Display: | Service Call 220: Error |
| Description: | Laser Synchronizing Detection Error: [K]/[Y] |
| Causes: | The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally. |
| Error code: | 221 |
| Description: | Laser synchronizing detection error: start position [K]: LD1 The laser synchronizing detection signal for the start position of the LDB [K], [Y], [M], [C] is not output for two seconds after LDB unit turns on while the polygon motor is rotating normally. |
| Causes: | • Disconnected cable from the laser synchronizing detection unit or defective connection • Defective laser synchronizing detector • Defective LDB • Defective EGB |
| Remedy: | 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the BCU. |
| Error code: | 230 |
| Display: | Service Call 230: Error |
| Description: | Paper Jam Clear Paper Path Leave Job in Finisher area 5 |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | Primary: Paper has most likely jammed in the duplex option. Remove the duplex tray to access the jam. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “230 Paper Jam” on page 2-74. |
| Error code: | 231 |
| Display: | Service Call 231: Error |
| Description: | FGATE OFF error: Bk • The PFGATE ON signal still asserts within 5 seconds after processing the image in normal job or MUSIC for end position [K]. • The PFGATE ON signal still asserts when the next job starts. |
| Causes: | • Defective ASIC (Lupus) • Poor connection between controller and EGB. • Defective EGB |
| Remedy: | 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board. |
| Error code: | 241 |
| Display: | Service call 241:Error |
| Description: | LD error: Y The EGB detects LDB error a few times consecutively when LDB unit turns on after LDB initialization |
| Causes: | • Worn-out LD • Disconnected or broken harness of the LD |
| Remedy: | 1. Replace the harness of the LD. 2. Replace the laser optics housing unit. 3. Replace the BCU. |
| Error code: | 280 |
| Description: | Paper Jam Clear Paper Path Leave sheets in Finisher area 5 |
| Causes: | • Defective BCU • Poor electrical connection • Noise |
| Remedy: | Primary: Media has jammed in the Finisher Option. Open the finisher option front door to access the jammed pages. Secondary: If sheets have been accumulated to be stapled when the jam is detected, the printer alternately flashes the primary and secondary messages indicating the accumulated sheets should not be removed during jam clearing. Note: When the secondary message is displayed, if the accumulated sheets are removed the printer will not reprint these sheets. Also if the print job is completed, the portion of the job printed after the jam will not be stapled. If removing the jammed media does not fix the problem, go to “280 Paper Jam” on page 2-82. |
| Error code: | 282 |
| Description: | Staple Jam Check Stapler Remove Job from Finisher |
| Causes: | • Defective BCU |
| Remedy: | The stapler device detects a paper jam during normal stapler operation such as when printing and stapling jobs. Check stapler are for jam in accumulator or stapler. Remove stapler cartridge to check for staple jam. Note: After the error has been cleared, the printer does not reprint any pages which existed in the accumulator for stapling. The following actions can be taken while either the primary or secondary messages are displayed: Press Go to initiate priming and resume printing. |
| Error code: | 300 |
| Description: | High voltage power output error |
| Causes: | The measured voltage is not correct when the EGB measures each charge output (charge, development, image transfer belt unit, and transfer unit). |
| Remedy: | • Disconnected or defective high voltage harness • Defective high voltage power supply • Defective EGB 1. Check or replace the harnesses. 2. Replace the high voltage power supply board 3. Replace the EGB. |
| Error code: | 302 |
| Description: | Copy cartridge (drum unit) must be replaced |
| Causes: | • Disconnected or broken high voltage cable • Defective or not installed PCU • Defective high voltage power supply |
| Remedy: | 1. Check or replace the connectors. 2. Replace the PCU for the affected colour. 3. Replace the high voltage power supply. |
| Error code: | 305 |
| Display: | ERROR 305 USB TIME OUT |
| Description: | Charge Corona Wire Cleaner Error The charge wire cleaner did not: (1) come from the home position within 5 s, or (2) did return to the home position within 3.75 s due to wire cleaner overload. |
| Causes: | • Cleaner unit blocked or damaged • Until replacement parts become available, set SP2804 to "0" to disable the charge-corona cleaning function so the machine can operate. |
| Error code: | 350 |
| Description: | ID sensor error 1 One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern. Vsp greater than or equals 2.5V Vsg less than 2.5 Vsp = 0V Vsg = 0 |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Error code: | 352 |
| Description: | ID sensor error 3 For 2 s during the ID sensor pattern check, the ID sensor pattern edge voltage is not 2.5V or the pattern edge is not detected within 800 ms. |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Remedy: | 1. Shake the toner bottle five or six times. 2. Check if the toner supply tube to sub-hopper unit is bent. 3. Check and reinstall the toner bottle. 4. Replace the toner bottle. |
| Error code: | 353 |
| Description: | ID sensor error 4 One of the following ID sensor output voltages is detected at ID sensor initialization. Vsg less than 4.0V when the maximum PWM input (255) is applied to the ID sensor. Vsg greater than or equal to 4.0V when the minimum PWM input (0) is applied to the ID sensor. |
| Causes: | • ID sensor defective • ID sensor harness disconnected • ID sensor connector defective • IOB defective • ID sensor pattern not written correctly • Incorrect image density • Charge power pack defective • ID sensor dirty |
| Remedy: | 1. Shake the toner bottle five or six times. 2. Check if the toner supply tube to sub-hopper unit is bent. 3. Check and reinstall the toner bottle. 4. Replace the toner bottle. |
| Error code: | 401 |
| Display: | ERROR 401 MOTOR X |
| Description: | ID Sensor Vsg Error The Vsg level was twice detected lower than 2.5 V. -or- The Vsg level was once detected higher than 4.8V. |
| Causes: | • ID sensor dirty • ID sensor harness, connector loose, disconnected, damaged, defective • ID sensor defective • MCU defective • CGB power pack defective |
| Error code: | 410 |
| Description: | ID sensor error: Development K. D evelopment gamma for black, magenta, cyan, or yellow is not within range (0.3 to 6.0). Process control halts when this SC is issued. |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | 1. Replace the ID/ MUSIC sensors. 2. Check the harness connection to the LD unit. 3. Replace the LD unit. 4. Check the harness connection to the CGB HVPS. 5. Replace the CGB HVPS. 6. Replace the developer. |
| Error code: | 411 |
| Display: | SVC 411 ERROR |
| Description: | IRQ timer 1 error |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | Replace the Controller board. |
| Error code: | 412 |
| Display: | SVC 412 ERROR |
| Description: | IRQ timer 2 error |
| Causes: | • ID/ MUSIC sensor shutter defective • LD sensor harness loose, broken, defective • LD unit not firing • CGB HVPS harness loose, broken, defective • CGB HVPS defective • Developer worn |
| Remedy: | Replace the Controller board. |
| Error code: | 420 |
| Display: | ERROR 420 Z POSITION |
| Description: | Potential sensor error: Vd Adjustment K. The drum potential sensor detects 150V or more on the drum (Vd) for 0.7 msec. when the high voltage charge is supplied to the drum for the initial sampling before exposure. |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Drum worn |
| Remedy: | 1. Clean or replace the drum potential sensor. 2. Replace the drum unit. |
| Error code: | 421 |
| Display: | ERROR 421 !CHECK FILTER |
| Description: | Potential sensor error: Vd Adjustment C. The drum potential sensor detects 150V or more on the drum (Vd) for 0.7 msec. when the high voltage charge is supplied to the drum for the initial sampling before exposure. |
| Causes: | • Drum potential sensor harness, connector is loose, broken, defective • Drum potential sensor dirty • Drum potential sensor defective • Drum connector, harness loose, broken, defective • Drum worn |
| Remedy: | 1. Clean or replace the drum potential sensor. 2. Replace the drum unit. |
| Error code: | 430 |
| Description: | Quenching lamp error At the completion of auto process control initialization, the potential of the drum surface detected by the potential sensor is more than -400V, the prescribed value. |
| Causes: | • Quenching lamp defective • Quenching lamp harness disconnected • Quenching lamp connector loose, defective |
| Error code: | 440 |
| Description: | Transfer Output Error. A high voltage feedback voltage of less than 0.5 V was detected for 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 460 |
| Description: | DC Separation Corona Output Error A dc separation feedback voltage of less than 0.5 V was detected after more than 200 ms. |
| Causes: | • High voltage cable disconnected, damaged • T/S power pack defective |
| Error code: | 461 |
| Description: | Humidity sensor error The output is 4.5 V (or higher) or 0.3 V (or lower) for 12 seconds. |
| Causes: | • Short circuit in the humidity sensor • Defective circuit • Defective connector |
| Error code: | 480 |
| Display: | Remove paper 480: Stacker full |
| Description: | Agitator Motor Error |
| Causes: | The agitator motor error is detected twice for 10 msec during the initialization at power-on or after the cover is closed. |
| Remedy: | • Disconnected or defective harness • Defective agitator motor 1. Check or replace the harness. 2. Replace the agitator motor. |
| Error code: | 481 |
| Description: | OPC belt sensor error |
| Causes: | • Defective OPC belt unit • Dirty OPC belt • Loose connection • Defective OPC belt sensor • Defective input output device • Defective BCU |
| Error code: | 503 |
| Display: | Service Call 503: Error |
| Description: | Tray 3 must be rebuilt |
| Causes: | (A model other than D581) Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. (D581) Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 504 |
| Description: | Tray 4 must be rebuilt |
| Causes: | The 2nd tray of D580, 1st tray of D580 when D579 and D580 are attached, the bottom D579 when two units of D579 are attached, or D631 when D581 and D631 are attached. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection D581 when D579 and D581 are attached.Defective stack transport clutch or connector disconnection. Transfer motor error/disconnection. Defective end fence home position sensor or connector disconnection. Defective tray lift motor or connector disconnection. Defective upper limit sensor or connector disconnection. Pickup SOL error/disconnection. Right tray sensor error/disconnection. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 515 |
| Display: | ERROR 515 DETECTION ERROR |
| Description: | DADF belt should be replaced |
| Causes: | • Rear fence motor defective or poor connection • Paper or other obstacle interfering with operation of the sensors • Paper or other obstacle trapped between tray and motor • Motor mechanical overload due to obstruction • Return sensor or HP sensor defective or dirty Note • This problem will not issue the SC code on the operation panel. • The machine will prompt the operator to reset tray by opening and closing it. • If the problem persists, the machine will display again and the tray cannot be used. |
| Error code: | 520 |
| Description: | Replace optics filter |
| Causes: | • Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective |
| Error code: | 521 |
| Description: | Replace particle filter |
| Causes: | • Physical obstruction blocking motor • Motor harness damaged, defective • Motor defective |
| Error code: | 530 |
| Description: | LSU Fan Motor Error |
| Causes: | A LOCK signal is not detected for more than ten seconds while the motor START signal is on and if this error occurs twice consecutively, this SC is issued. |
| Remedy: | • Disconnected or defective motor harness. • Defective LSU fan motor 1. Check or replace the motor harness. 2. Replace the LSU fan motor. |
| Error code: | 541 |
| Description: | Thermistor Error |
| Causes: | The thermistor output is less than 0°C for 7 seconds. |
| Remedy: | • Disconnected thermistor • Defective harness connection 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 542 |
| Description: | Print Ready Temperature Error |
| Causes: | • The heating roller temperature increase during a set time is not correct. • The fusing temperature does not reach the print ready temperature within a set time after the fusing lamp has turned on. |
| Remedy: | • Defective thermistor • Incorrect power supply input at the main power socket • Defective fusing lamp 1. Check the voltage of the wall outlet. 2. Replace the fusing unit 3. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 543 |
| Description: | High Temperature Detection Error |
| Causes: | This SC is issued if one of following conditions occurs: • The thermistor (center) detects 255?XC or thermistor (end) detects 245?XC. • The thermistor (center) detects a 3?XC increment or more for five seconds at 220?XC or more or the thermistor (end) detects a 4?XC increment or more for five seconds at 210?XC or more.ne |
| Remedy: | • Defective I/O control (EGB) • Defective EGB 1. Replace the EGB • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 544 |
| Description: | Fusing Temperature: Error 2 (Hardware Detection) The fusing thermistor that monitors the temperature of the hot roller detected a fusing temperature of 235oC (455oF), due to a Triac short which interfered with fusing temperature control. |
| Causes: | • MCU defective • PSU defective • Fusing unit defective |
| Error code: | 545 |
| Description: | Heating Lamp Full-Power Error |
| Causes: | The fusing lamp is fully-powered for a certain time while the fusing unit stays in the stand-by mode and is not rotating. |
| Remedy: | • Deformed thermistor • Thermistor not in the correct position • Defective fusing lamp 1. Replace the fusing unit. 2. Replace the fusing lamp. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. |
| Error code: | 546 |
| Description: | Fusing Temperature: Error 4 The machine detected that the fusing temperature was fluctuating out of range for more than 60 sec. (7 readings detected temperature fluctuating more than ±20C) |
| Causes: | • Thermistor connection loose, disconnected, defective • Hot roller thermistor not positioned correctly • Fusing lamp connections loose, disconnected, defective • MCU defective |
| Error code: | 547 |
| Description: | Zero Cross Error |
| Causes: | The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. |
| Remedy: | • Defective fusing lamp relay 1. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 551 |
| Description: | Pressure roller center thermistor error 1. During the hot roller temperature control sequence, or while the hot roller and pressure roller were rotating, the pressure roller center thermistor measured a value higher than 3.3V 10 consecutive times at 600 ms intervals. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 552 |
| Description: | Fusing sleeve belt warm-up error 2 The fusing sleeve belt temperature does not reach 81C for 6 seconds after the inverter turned on.) |
| Causes: | Dirty thermopile lenses. Deformed thermistor. |
| Error code: | 553 |
| Description: | Pressure roller center thermistor error 2 During the hot roller temperature control sequence, the pressure roller center thermistor measures a value lower than 0.2V. |
| Causes: | • Pressure roller center thermistor not positioned properly • Pressure roller center thermistor connector loose, broken, defective • Pressure roller center thermistor defective • MCU defective |
| Error code: | 554 |
| Description: | Fusing sleeve belt overheat: End (hardware error) The fusing sleeve belt thermistor detects 250°C or more. |
| Causes: | Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system. |
| Remedy: | • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. • Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: The fusing unit cannot be used because an abnormal high temperature was detected. • After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC. |
| Error code: | 555 |
| Description: | Fusing Heater error: End The fusing heater keeps full power for 9 seconds or more. |
| Causes: | Defective thermistors. Broken heater cables. |
| Error code: | 556 |
| Description: | Unstable fusing temperature (rear) The fusing temperature varies 50° C or more within 1 second, and this occurs 2 consecutive times. |
| Causes: | • Thermistor defective or out of position • Power supply unit defective |
| Error code: | 557 |
| Description: | Zero Cross Frequency Error |
| Causes: | The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. |
| Remedy: | • Defective fusing lamp relay • Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit. 3. Turn the main power switch off and on. • Execute "Engine Maintenance Menu" to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated. The power should be turned off and on after the recovery procedure. |
| Error code: | 570 |
| Description: | Charge bias leak High voltage unit sends a signal of charge bias leak. |
| Causes: | • Defective charge roller • Defective high voltage unit |
| Error code: | 571 |
| Description: | Pressure roller thermistor error: Center The center temperature of the pressure roller measured by the thermistor does not reach 0°C for 8 seconds. |
| Causes: | Defective thermopile. Defective thermistor. Loose connection. |
| Error code: | 572 |
| Description: | Belt temperature error The temperature sensor at the belt unit detects unusual temperature for 0.8 seconds. |
| Causes: | • Disconnect harness • Defective temperature sensor at the ink head |
| Remedy: | 1. Check the connector (CN139, CONIJ-CN503 and CN507). 2. Replace the temperature sensor at the ink head. |
| Error code: | 620 |
| Display: | ERROR 620 POSITIVE P.NotEnough |
| Description: | Communication timeout error between BICU and finisher The BICU did receive a response within 100 ms after 3 attempts after sending data to the finisher. |
| Causes: | • Serial line connecting BICU and finisher unstable • External noise • BICU board and finisher main board connection defective or loose • Finisher main board defective • BICU board defective |
| Remedy: | 1. Check or replace the cable between IPU and ADF. 2. Replace the ADF. 3. Replace the IPU. |
| Error code: | 630 |
| Description: | CSS communication error A communication error occurred during communication with the CSS. |
| Causes: | • Communication line error |
| Remedy: | Logging only. |
| Error code: | 632 |
| Description: | Key/card counter device error 1 After 1 data frame is sent to the device, an ACK signal is not received within 100 ms, and is not received after 3 retries. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 633 |
| Description: | Key/card counter device error 2 During communication with the device, the MCU received a break (Low) signal. |
| Causes: | • Serial line from the device to the main machine is unstable, disconnected, or defective |
| Error code: | 634 |
| Description: | Key/card counter device error 3 The backup battery of the counter device RAM is low. |
| Causes: | • RAM backup battery exhausted • Counter device defective |
| Error code: | 635 |
| Description: | Key/card counter device error 4. After installation of the device a message alerts user to a battery voltage abnormal error. |
| Causes: | • Device control board defective • Device control board backup battery defective |
| Error code: | 640 |
| Description: | Communication error: Engine Controller (Check sum error) Sum value is added each command frame. Sum check means: STX xx xx xx xx sum ETX -> The least significant 7 bits of xx + xx + xx+ xx is compared with the sum Example: STX 80h 81h 82h 83h 06h ETX -> 80h + 81h + 82h + 83h = 206h If sum value is 06h, data is correct. This SC is not displayed when it occurs; count is executed only by logging. |
| Causes: | Hard error with PCI |
| Remedy: | 1. Turn the main switch off and on. |
| Error code: | 641 |
| Description: | BICU control data transfer abnormal A sampling of the control data sent from the BICU reveals an abnormality. |
| Causes: | • Defective controller board • External noise • Defective BCU |
| Remedy: | 1. Replace the controller board. 2. Replace the BCU. |
| Error code: | 670 |
| Description: | Engine startup error The MCU failed to respond within the prescribed time when the machine was turned on. |
| Causes: | • Connections between MCU and controller board are loose, disconnected, or damaged • MCU defective • Controller board defective |
| Error code: | 672 |
| Description: | Controller startup error After power on, the line between the controller and the operation panel did not open for normal operation. -or- After normal startup, communication with the controller stopped. |
| Causes: | • Controller installed incorrectly • Controller board defective • Operation panel harness disconnected or defective |
| Error code: | 685 |
| Description: | SBU/IPU communication error While data is sent between the scanner and BICU board, a communication error has occurred. |
| Causes: | • Defective scanner unit cable • Defective SBU board • Defective BICU board |
| Error code: | 687 |
| Description: | Memory address command error |
| Causes: | • Among the I/F commands with the controller, the image transfer available report (for each command) cannot be received. • The image data cannot be prepared at the controller due to a problem. • Communication error • An error has occurred inside the controller. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 720 |
| Description: | Fan folder transport motor error A transport motor lock signal was detected for more than 5 sec. while the motor was running. |
| Causes: | • Transport motor harness connector loose, disconnected, broken • Motor overload due to an obstruction • Transport motor defective • Fan folder unit MCU defective |
| Error code: | 722 |
| Description: | Finisher jogger motor error The finisher jogger HP sensor did not return to the home position, or move out of the home position, within 1.25 sec. Staple mode cannot be used. |
| Causes: | • Jogger motor connector or harness loose, broken, defective • Jogger motor defective • Jogger HP sensor connector or harness loose, broken, defective • Jogger HP sensor defective |
| Error code: | 724 |
| Description: | Finisher staple hammer motor error Stapling does not finish within 150 ms after the staple hammer motor turned on. Staple mode cannot be used. |
| Causes: | • Staple jam • Stapler overload caused by trying to staple too many sheets • Staple hammer motor connector or harness loose, broken, defective • Staple hammer motor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the staple hammer motor HP sensor if the motor is rotating. 4. Replace the finisher main board. |
| Error code: | 725 |
| Description: | Finisher exit guide plate motor error After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defective |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the guide plate motor mechanism. 3. Replace the guide plate position sensor and/or guide plate motor. 4. Replace the finisher main board. |
| Error code: | 726 |
| Description: | Front shift jogger motor error (B703) The sides fences do not retract within the prescribed time after the shift jogger motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift jogger motor disconnected, defective • Shift jogger motor overloaded due to obstruction • Shift jogger HP sensor disconnected, defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift jogger HP sensor 4. Replace the shift jogger motor. 5. Replace the finisher main board. |
| Error code: | 727 |
| Description: | Rear shift jogger motor (B703) The side fences do not retract within the prescribed time after the shift jogger motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code |
| Causes: | Motor harness disconnected, loose, defective Motor defective Motor overload HP defective boar |
| Error code: | 728 |
| Description: | Shift jogger retraction motor error (B703) The side fences do not retract within the prescribed time after the retraction motor switches on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Motor harness disconnected, loose, defective • Motor defective • Motor overload • HP defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift tray jogger lift HP sensor. 4. Replace the shift jogger retraction motor. 5. Replace the finisher main board. |
| Error code: | 730 |
| Description: | Finisher Tray 1 shift motor error The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. |
| Causes: | • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in shift motor mechanism. 3. Replace the shift tray HP sensor and/or shift motor 4. Replace the finisher main board. |
| Error code: | 731 |
| Description: | Finisher exit guide motor error After the finisher exit guide motor turned on, the exit guide sensor did not activate within 800 ms. |
| Causes: | • Finisher exit guide motor defective harness or connector loose, broken, defective • Finisher exit guide motor defective • Finisher exit guide sensor defective |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the upper tray exit motor. 4. Replace the finisher main board. |
| Error code: | 732 |
| Description: | Finisher shift roller motor error The shift roller HP sensor does not activate within the prescribed time after the shift roller motor turns on. After 2 counts, the SC is logged as a jam. |
| Causes: | • Shift roller HP sensor defective • Sensor harness disconnected, defective • Shift roller motor defective • Finisher main board defective • Shift roller motor overload |
| Remedy: | 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the shift tray exit motor. 4. Replace the finisher main board. |
| Error code: | 740 |
| Description: | Finisher corner stapler motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 3000-sheet finisher • Staple movement is not finished after a certain time. For the 1000-sheet booklet finisher • The stapler motor does not switch off within the prescribed time after operating. • The HP sensor of the staple unit does not detect the home position after the staple unit moves to its home position. • The HP sensor of the staple unit detects the home position after the staple unit moves from its home position. |
| Causes: | • Staple jam • Motor overload • Defective stapler motor |
| Remedy: | 1. Check the connections and cables for the components mentioned above. 2. Replace the HP sensor and/or stapler motor 3. Replace the finisher main board. |
| Error code: | 750 |
| Description: | 1000/3000-sheet (booklet) finisher: Tray lift motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. The upper tray paper height sensor does not change its status with the specified time after the tray raises or lowers. |
| Causes: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor |
| Remedy: | 1. Check the connections to the shift tray motor. 2. Defective shift tray motor. |
| Error code: | 770 |
| Description: | Shift motor error The shift motor HP sensor does not detect any change for 1.86 seconds after the shift motor has turned on at power on or during its operation. |
| Causes: | Defective shift motor. Defective shift motor HP sensors. |
| Remedy: | Turn the main power switch off and on. |
| Error code: | 791 |
| Description: | Bridge unit error The machine recognizes the finisher, but does not recognize the bridge unit. |
| Causes: | The bridge unit is not installed. Defective bridge unit. Re-install the bridge unit. Turn the main power switch off and on. |
| Remedy: | • Re-install the bridge unit. • Turn the main power switch off and on. |
| Error code: | 792 |
| Description: | Finisher error The machine does not recognize the finisher, but recognizes the bridge unit. |
| Causes: | The finisher`s connection is faulty. The finisher is not attached to a device equipped with the bridge unit. Defective finisher. |
| Remedy: | Reconnect the finisher or bridge unit, and then turn the main power switch off and then back on. |
| Error code: | 793 |
| Description: | Finisher gathering roller motor error |
| Causes: | • Motor overload • Loose connection of the gathering roller motor • Defective gathering roller motor |
| Remedy: | • Check the connections to the gathering roller motor. • Replace the gathering roller motor. |
| Error code: | 800 |
| Description: | Startup without video output end error (K) Video transfer to the engine is started, but the engine did not issue a video transmission end command within the specified time. |
| Causes: | • Controller board defective |
| Error code: | 801 |
| Display: | SYSTEM HALT (*) 801 : (C)OPCODE |
| Description: | Video output error (Y) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 802 |
| Display: | SYSTEM HALT (*) 802 : (C)SLOT |
| Description: | Video output error (M) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 803 |
| Display: | SYSTEM HALT (*) 803 : (C)CPU ADDR |
| Description: | Video output error (C) |
| Causes: | Data transfer starts to the BCU, but the transfer completion command does not return to the controller within the required time. Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 804 |
| Display: | SYSTEM HALT (*) 804 : (C)DMA ADDR |
| Description: | Startup without video input end (K) A video transmission was requested from the scanner, but the scanner did not issue a video transmission end command within the specified time. |
| Causes: | • Controller board defective |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 805 |
| Display: | SYSTEM HALT (*) 805 : (C)ZERO DIV |
| Description: | Startup without video input end error (Y) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one. |
| Error code: | 806 |
| Display: | SYSTEM HALT (*) 806 : FW/SIO bit |
| Description: | Startup without video input end error (M) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 807 |
| Display: | SYSTEM HALT (*) 807 : FW/SIO wbsy |
| Description: | Startup without video input end error (C) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 808 |
| Display: | SYSTEM HALT (*) 808 : FW/STP-MTR |
| Description: | Startup without video input end error (R) Video transfer to the engine is started, but a video transmission end command is not issued by the scanner within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 809 |
| Display: | SYSTEM HALT (*) 809 : FW/XY param |
| Description: | Startup without video input end error (G) Video transfer to the engine is started, but a video transmission end command is not issued by the engine within the specified time. |
| Causes: | • Defective controller board |
| Error code: | 810 |
| Display: | SYSTEM HALT (*) 810 : FW/KEY RDI |
| Description: | Startup without video input end error (B) Video transfer to the engine is started, but a video transmission end command is not issued by the engine within the specified time. |
| Causes: | • Defective controller board |
| Remedy: | 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one. |
| Error code: | 818 |
| Display: | SYSTEM HALT (*) 818 : FW/EEP SIZE |
| Description: | Watch-dog error While the system program is running, other processes do not operate at all. |
| Causes: | • Defective controller • Software error |
| Remedy: | 1. Replace the controller. |
| Error code: | 819 |
| Display: | SYSTEM HALT (*) 819 : FW/HROM SIZ |
| Description: | Service Cycle Power |
| Causes: | • Incorrect combination of EGB and controller board. • An unexpected error occurs in the EEPROM on the controller board. |
| Remedy: | • Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller boardng fan |
| Error code: | 820 |
| Description: | Self-Diagnostic Error: CPU The CPU returned an unexpected error during the self-diagnostic test. |
| Causes: | • Controller board defective • Insufficient memory • Expanded memory defective |
| Error code: | 821 |
| Description: | Self-diagnostic error 2: ASIC The ASIC provides the central point for the control of bus arbitration for CPU access, for option bus and SDRAM access, for SDRAM refresh, and for management of the internal bus gate. |
| Causes: | • Controller board defective |
| Remedy: | For more details about this SC code error, execute SP5990 to print an SMC report so that you can read the error code. The error code is not displayed on the operation panel. |
| Error code: | 822 |
| Description: | Self-diagnostic error 3: HDD An error occurred when the self-check was performed when the machine was switched on after the HDD was replaced. (The diagnostic command was issued to the HDD device but the result was an error). |
| Causes: | • HDD defective • HDD harness disconnected, defective • Controller board defective |
| Error code: | 823 |
| Description: | USB/ Network Device Error |
| Causes: | An interface error in the USB connection or NIB connection occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 824 |
| Display: | XY MOVE CTRL |
| Description: | EEPROM Error |
| Causes: | An EEPROM check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 826 |
| Display: | SYSTEM HALT (*) 826 : FW/SV MDL |
| Description: | Self-diagnostic Error 5: RTC/Optional NVRAM The NVRAM or optional NVRAM returned an error during the self-diagnostic test. |
| Causes: | • Make sure NVRAM is seated correctly in its socket • Replace the NVRAM on the controller board |
| Error code: | 827 |
| Display: | SYSTEM HALT (*) 827 : FW/PRN MDL |
| Description: | On-Board Memory Check Error |
| Causes: | An on-board memory check error at power-on occurs. |
| Remedy: | • Controller board detective 1. Replace the controller board. |
| Error code: | 828 |
| Display: | SYSTEM HALT (*) 828 : FW/SV MDL |
| Description: | ROM Checksum Error |
| Causes: | A ROM checksum error at power-on occurs. |
| Remedy: | 1. Replace the controller board. |
| Error code: | 829 |
| Display: | SYSTEM HALT (*) 829 : FW/ERASE TIMEOV |
| Description: | Self-diagnostic Error 9: Optional RAM The optional RAM returned an error during the self-diagnostic test. |
| Causes: | • Replace the optional memory board • Controller board defective |
| Error code: | 835 |
| Display: | SYSTEM HALT (*) 835 : FW/PRN MDL |
| Description: | Self-diagnostic error: Centronic device |
| Causes: | [1102] Loopback connector is connected but check results in an error. • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [110C] Loopback connector is connected but check results in an error. • ASIC device error • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [1120] Centronic loopback connector is not connected for detailed self-diagnostic test. • Centronic loopback connector not connected correctly • Centronic loopback connector defective • ASIC device defective Replace the controller board. |
| Error code: | 836 |
| Display: | SYSTEM HALT (*) 836 : FW/SV MDL |
| Description: | Self-diagnostics error: Font ROM (standard) |
| Causes: | Turn the main switch off and on. Replace the standard ROM-DIMM. |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the controller board. |
| Error code: | 837 |
| Display: | SYSTEM HALT (*) 837 : FW/PRN MDL |
| Description: | Self-diagnostic error - Optional font ROM The data in the font ROM (optional ROM-DIMM) is damaged. |
| Causes: | • Defective optional ROM-DIMM. |
| Remedy: | 1. Turn the main switch off and on. 2. Replace the optional ROM-DIMM. |
| Error code: | 838 |
| Display: | SYSTEM HALT (*) 838 : FW/SV MDL |
| Description: | Self-diagnostic Error 10: Clock Generator A verify error occurred when setting data was read from the clock generator via the I2C bus. |
| Causes: | • Replace the controller board |
| Error code: | 850 |
| Description: | Net I/F error Duplicate IP addresses. Illegal IP address. Driver unstable and cannot be used on the network |
| Causes: | • IP address setting incorrect • NIB (PHY) board defective • Controller board defective |
| Remedy: | Turn the main switch off and on. |
| Error code: | 851 |
| Description: | IEEE 1394 I/F Error IEEE1394 cannot be used due to a faulty driver setting or poor I/F connection. |
| Causes: | • Faulty PCI connection • IEEE1394 board defective • Controller board defective |
| Error code: | 853 |
| Description: | Wireless LAN Error 1 During machine start-up, the machine can access the board that holds the wireless LAN, but not to the wireless LAN card. |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 854 |
| Description: | Wireless LAN Error 2 During machine operation, the machine can get access to the board that holds the wireless LAN, but not to the wireless LAN card (802.11b or Bluetooth). |
| Causes: | • Wireless LAN card missing (was removed) |
| Error code: | 855 |
| Description: | Wireless LAN error 3 An error was detected on the wireless LAN card. |
| Causes: | • Wireless LAN card defective • Wireless LAN card connection incorrect |
| Error code: | 856 |
| Description: | Wireless LAN error 4. An error was detected on the wireless LAN board. |
| Causes: | • Wireless LAN board defective • PCI connector to MB loose |
| Error code: | 860 |
| Description: | HDD startup error at power on HDD is connected but a driver error is detected. -or- The driver does not respond with the status of the HDD within 30 s. |
| Causes: | • HDD is not initialized • Level data corrupted • HDD is defective |
| Error code: | 861 |
| Description: | HDD re-try failure At power on the HDD was detected. Power supply to the HDD was interrupted after the system entered the energy save mode, but after the HDD was awakened from the energy save mode it did not return to the ready status within 30 sec. |
| Causes: | • Harness between HDD and controller board disconnected, defective • HDD power connector disconnected • HDD defective • Controller board defective |
| Error code: | 862 |
| Description: | Bad sector number error The number of bad sectors in the HDD (image data area) goes over 101. |
| Causes: | • Defective HDD |
| Remedy: | Format the HDD with SP5832-001. Replace the HDD. |
| Error code: | 863 |
| Description: | HDD data read failure The data written to the HDD cannot be read normally, due to bad sectors generated during operation. |
| Causes: | • HDD defective |
| Remedy: | • If the bad sectors are generated at the image partition, the bad sector information is written to NVRAM. • The next time the HDD is accessed, these bad sectors will not be accessed for read/write operation. The HDD will probably require replacement soon. |
| Error code: | 864 |
| Description: | HDD data CRC error. During HDD operation, the HDD cannot respond to a CRC error query. Data transfer did not execute normally while data was being written to the HDD. |
| Causes: | • HDD defective |
| Error code: | 865 |
| Description: | HDD access error HDD responded to an error during operation for a condition other than those for SC863, 864. |
| Causes: | • HDD defective |
| Error code: | 870 |
| Description: | Address book data error Address book data on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network. The address book data cannot be read from the HDD or SD card where it is stored, or the data read from the media is defective. |
| Causes: | • Turn the machine power off/on. If this does not solve the problem, do the Procedure below. • HDD defective |
| Remedy: | 1. Do SP5846-50 (UCS Settings – Initialize all Directory Info.) to reset all address book data. 2. After 3 sec. reformat the HDD with SP5821-1. 3. Turn the main power switch off/on. |
| Error code: | 880 |
| Description: | File Format Converter (MLB) error A request to access the MLB was not answered within the specified time (60 sec.). |
| Causes: | • File format converter board defective |
| Error code: | 900 |
| Description: | RIP Software |
| Remedy: | 1 Printer POR Turn the printer off and on several times. If Error Code 900 continues to display, go to step 2. 2 System board Turn the machine off and on several times, waiting a few minutes between power on and power off. If Error Code 900 continues to display, go to step 3. 3 Factory defaults Restore factory defaults. See “EP Defaults”. This resets the non-critical areas of the user NVRAM. If Error Code 900 continues to display, go to step 4. 4 Sub error codes With Error Code 900 displayed, press and 2. Record the complete list of Sub Error Codes on the display, then call your next level of support or call Toshba. |
| Error code: | 901 |
| Display: | Power OFF/ON 901:Error |
| Description: | Engine flash error |
| Causes: | Indicates that the flash which the system board code is programmed into is bad. Replace the system board. |
| Remedy: | Replace the system board. |
| Error code: | 902 |
| Display: | Power OFF/ON 902:Error |
| Description: | Engine software error |
| Causes: | These errors indicate an unrecoverable system software error. |
| Remedy: | Replace the system board. |
| Error code: | 925 |
| Display: | Power Off/on 925: Error |
| Description: | Fuser Error |
| Causes: | Defective HDD. Hard disk data inconsistencies due to power interruption during writing to the hard disk. Defective software. |
| Remedy: | Wrong fuser lamp installed. 1 Fuser lamp (incorrect lamp/ 925 Service Error) Install the correct voltage and wattage lamp or fuser assembly. See “Fuser assembly removal”. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. 2 Fuser lamp fuser top cover assembly Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See “Fuser assembly removal” • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly. 3 LVPS LVPS to fuser AC cable CAUTION: When taking measurements for AC power, observe all safety precautions. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable. If the voltage is incorrect, turn the power off, and remove the LVPS. Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. If correct, check the continuity of the LVPS to fuser AC cable. If incorrect, replace the cable. If the AC line voltage at CN1 is incorrect, check fuse F2. If the fuse is blown, replace the fuse. If the fuse is not blown, replace the LVPS assembly. |
| Error code: | 990 |
| Display: | Inspection is required. 990 : Error |
| Description: | <device> |
| Causes: | • Firmware defective: re-boot • Update firmware |
| Remedy: | Indicates an equipment check condition has occurred in the specified device, but the device is unable to identify the exact component failure. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 991 |
| Description: | <device> Card |
| Causes: | Software defective, re-boot |
| Remedy: | The specified device has detected an equipment check in its system card. Note: <device> can be one of the following: duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin. |
| Error code: | 995 |
| Description: | Finisher Main Feed Motor abnormal |
| Causes: | -01 D • Defective BCU • NVRAM Replacement error • Install the previous NVRAM • Input the serial number with SP5-811-004, and turn the main power switch off and on. -02 D • Defective NVRAM • Defective controller Perform SP5-825 to download the appropriate data to the NVRAM, and then turn the main power switch off and then back on. -03 D The serial number cannot be identified due to a mistake during controller replacement or mechanical failure. Replace the controller with the correct type. -04 D - Place all parts in the initial state, and then replace the parts according to the procedures described in the manuals. |
| Remedy: | 1 Is there jammed paper or other obstructions in the paper path? Clear the paper path. Go to step 2. 2 Check to ensure the connector PJ6 on the finisher control board and the feed motor assembly cable are properly connected. Are the cables properly connected? Go to step 3. Properly connect the cables. 3 Make sure the finisher set switch is activated. Measure for +24 V dc (–10%) between pins 7 and 8 and +5 V dc (–10%) between pins 7 and 6 on the feed motor assembly cable connector CN1. Is either voltage missing? Go to step 4. Go to step 5. 4 Disconnect the feed motor assembly cable and PJ6 on the finisher control board. Measure continuity on the cable for all positions. Is there continuity? Go to step 6. Replace the cable. 5 Replace the feed motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 6 Measure for +24 V dc between pins 1 and 2 on connector PJ3 on the finisher control board. Measure for +5 V dc between pins 1 and 3 on PJ2 on the finisher control board. Is either voltage missing? Replace the power supply. Replace the finisher control board. |
| Error code: | 997 |
| Description: | Finisher Tractor Motor Error |
| Causes: | • Software bug • A RAM or DIMM option required for the application is not installed or not installed correctly. |
| Remedy: | 1 Are there obstructions or foreign objects in the accumulator or face down paper path? Remove the objects or obstructions. Go to step 2. 2 Are the connectors CN3 at the tractor motor and PJ4 on the finisher control board securely connected? Go to step 3. Securely connect the connectors. 3 Make sure the finisher set switch is activated. Measure +24 V dc between pin 1 of tractor motor connector CN3 and frame ground. Is +24 V dc (–10%)? Go to step 4. Go to step 5. 4 Replace the tractor motor assembly. Did this resolve the problem? Problem solved. Replace the finisher control board. 5 Disconnect CN3 and PJ4 on the finisher control board and perform a continuity check on all positions. Is there continuity on all positions? Go to step 6. Replace the cable. 6 Check for +24 V dc between pins 1 and 2 of PJ3 on the finisher control board. Is +24 V dc present? Replace the finisher control board. Replace the power supply. |
| Error code: | 998 |
| Description: | Tray Elevator Motor Error |
| Causes: | • Software bug • A RAM or DIMM option needed for the application not installed, or not installed correctly • Controller board defective |
| Remedy: | 1 Are the connectors CN4 at the tray elevator motor and connector PJ4 on the finisher control board properly connected? Go to step 2. Properly connect the connectors. 2 Make sure that the finisher set switch is activated. Power the printer off. Measure for approximately +24 V dc (–10%) between pins 1 and 2 of connector CN4 at the tray elevator motor. Power the printer on and observe the voltage meter during the first 12 seconds of power up. Is +24 V dc present while the printer is powering up? Replace the tray elevator motor. Go to step 3. 3 Disconnect CN4 at the tray elevator motor. Disconnect PJ4 on the finisher control board. Measure for continuity between CN4 pin 1 and PJ4 pin 7. Measure for continuity between CN4 pin 2 and PJ4 pin 8. Is there continuity in both locations? Go to step 4. Replace the cable. 4 Measure for +24 V dc (–10%) between pins 1 and 2 on connector PJ6. Is +24 V dc present? Replace the finisher control board. Replace the finisher power supply. |
| Error code: | 999 |
| Display: | Service call 999: Error |
| Description: | Stapler Motor Error |
| Causes: | • Color registration (MUSIC) failure |
| Remedy: | 1 Are staples jammed in the stapler? Go to step 2. Go to step 3. 2 Clear the staple jam and run the staple test in diagnostic mode or run a staple job. Does the problem reoccur? Replace the staple cartridge and to go step 4. Problem solved. 3 Are the connectors CN5 on the stapler and PJ1 on the finisher control board securely connected? Go to step 5. Securely connect the connectors. 4 Did replacement of the stapler cartridge resolve the problem? Problem resolved. Replace the stapler. 5 Make sure the finisher set switch is activated. Measure for 5 V dc between pins 11 and 12 on stapler connector CN5. Is 5 V dc present? Replace the stapler. Replace the finisher control board. 6 Did replacement of the finisher control board correct the problem? Problem solved. Go to step 7. 7 Is there continuity on the stapler to finisher control board cable? Replace the power supply. Replace the cable. |
Название
RICOH TYPE T2 Тонер-картридж черный
RICOH TYPE T2 Тонер-картридж желтый
RICOH TYPE T2 Тонер-картридж пурпурный
RICOH TYPE T2 Тонер-картридж голубой
RICOH Блок проявки черный
RICOH Блок проявки пурпурный
RICOH Блок проявки голубой
RICOH Блок проявки желтый
RICOH Блок фотобарабана
