Kyocera TASKalfa 4501i
Рейтинг
Модули
Covers 2
Drive Section 2 (55/45 ppm)
Paper Feed Section 1 (55/45 ppm)
PAPER FEED SECTION 2
Inner Section 1-1
FRAMES
(Электронные компоненты)
Paper Conveying Section 2
Paper Conveying Section 3
ADF 1
Paper Cassettes
Exit Section
Drive Section 1
Paper Feed Section 1 (35 ppm)
PAPER FEED
CASSETTE ASSEMBLY
COVERS
Operation Section
Drive Section 2 (35 ppm)
Covers 1
Fuser Section
Paper Conveying Section 1-1
Inner Section 2
Covers 3
Inner Section 1-2
Image Formation & Developer Section
Scanner & Laser Scanner Section
(Узел термозакрепления)
Electrical Components 1
Paper Conveying Section 1-2
ELECTRICAL COMPONENTS 2
Paper Conveying Section 1-3
COOLING SECTION
Детали Drive Section 2 (35 ppm)
| Деталь: | FILTER LEFT SIDE |
| Парткод: | 302LC33370 |
| Цена: | 3 900 ₽ |
| Деталь: | MAGNET CLIP DISH |
| Парткод: | 302GR04370 |
| Деталь: | SEAL MAGNET |
| Парткод: | 302GR04380 |
| Деталь: | MAGNET CATCH |
| Парткод: | 302H004660 |
| Деталь: | LID LEFT COVER REAR |
| Парткод: | 302LC04110 |
| Деталь: | COVER LEFT UPPER |
| Парткод: | 302N404050 |
| Деталь: | COVER ISU REAR |
| Парткод: | 302LC04151 |
| Деталь: | COVER FRONT UPPER |
| Парткод: | 302N404030 |
| Деталь: | COVER FRONT UPPER B |
| Парткод: | 302N404260 |
| Деталь: | COVER FRONT UPPER RIGHT |
| Парткод: | 302LC04182 |
| Деталь: | SEAL FRONT FAN A |
| Парткод: | 302LH33040 |
| Деталь: | COVER LEFT |
| Парткод: | 302LH04031 |
| Деталь: | LID USB FRONT |
| Парткод: | 302N404240 |
| Деталь: | MOUNT COVER LEFT |
| Парткод: | 302LC04480 |
| Деталь: | COVER DP CONNECTOR |
| Парткод: | 302N404370 |
| Деталь: | LID DP CONNECTOR |
| Парткод: | 302LC04330 |
| Деталь: | COVER ISU LEFT SUB |
| Парткод: | 302LC04340 |
| Деталь: | CASE CLIP |
| Парткод: | 302N404130 |
| Деталь: | COVER INNER FAN |
| Парткод: | 302LH04021 |
| Деталь: | LID CARD |
| Парткод: | 302N404040 |
| Деталь: | COVER INNER CONVEYING F |
| Парткод: | 302LC29090 |
| Деталь: | COVER RIGHT FRONT |
| Парткод: | 302LC29081 |
| Деталь: | LABEL OPERATION CAUTION B |
| Парткод: | 302LC34031 |
| Деталь: | FILTER TOP |
| Парткод: | 302N433010 |
| Цена: | 5 000 ₽ |
| Деталь: | COVER FILTER EXIT |
| Парткод: | 302K933181 |
| Деталь: | LID COVER LEFT |
| Парткод: | 302N404380 |
| Деталь: | PARTS FILTER BELT UNIT(V) SP |
| Парткод: | 302LC94130 |
| Деталь: | PARTS FILTER FAN ASSY(Z) SP |
| Парткод: | 302LF94300 |
| Деталь: | WIRE USB KEYBOARD |
| Парткод: | 302N446220 |
| Деталь: | WIRE USB CARD READER |
| Парткод: | 302N446230 |
| Деталь: | SPRING USB HOLD |
| Парткод: | 302K905900 |
| Деталь: | MOUNT USB LEFT |
| Парткод: | 302N404180 |
| Деталь: | PLATE EARTH VF B |
| Парткод: | 302FB07930 |
| Деталь: | FILTER EXIT UNIT |
| Парткод: | 302K994101 |
| Цена: | 4 300 ₽ |
| Деталь: | HOLDER FEED DRIVE |
| Парткод: | 302K931411 |
| Деталь: | SHAFT MID DRIVE |
| Парткод: | 302K931441 |
| Деталь: | COUPLING DRIVE |
| Парткод: | 302K931530 |
| Деталь: | SPRING DRUM JOINT |
| Парткод: | 302H712650 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | SHAFT FEED DRIVE |
| Парткод: | 302K931431 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | SHAFT ASSIST DRIVE |
| Парткод: | 302K931480 |
| Деталь: | GEAR Z28L |
| Парткод: | 302K931490 |
| Деталь: | PARTS CLUTCH 50 Z35R SP |
| Парткод: | 303M894090 |
| Деталь: | PIN FEED DRIVE |
| Парткод: | 302K931450 |
| Деталь: | GEAR Z28R |
| Парткод: | 302K931500 |
| Деталь: | GEAR Z27L |
| Парткод: | 302K931550 |
| Деталь: | GEAR Z27L MAIN |
| Парткод: | 302JZ31170 |
| Деталь: | GEAR Z35R |
| Парткод: | 302K931510 |
| Деталь: | GEAR Z40L-Z34L |
| Парткод: | 302K931520 |
| Деталь: | GEAR Z61R-Z34R |
| Парткод: | 302K931470 |
| Деталь: | WIRE ASSIST CLUTCH |
| Парткод: | 302K946690 |
| Деталь: | PLATE FEED DRIVE |
| Парткод: | 302K931420 |
| Деталь: | PARTS MOTOR-BL W30 SP |
| Парткод: | 302K994330 |
| Деталь: | PLATE EARTH FEED |
| Парткод: | 302K931540 |
| Деталь: | PARTS PWB FEED 2 ASSY SP |
| Парткод: | 302N494170 |
| Деталь: | WIRE FEED MOTOR |
| Парткод: | 302K946441 |
| Деталь: | WIRE FEED CLUTCH |
| Парткод: | 302K946AB0 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | HOLDER CONT DRIVE K |
| Парткод: | 302K931710 |
| Деталь: | PARTS LSU RETAINER MOTOR ASSY SP |
| Парткод: | 302K994140 |
| Деталь: | SEAL MOTOR DC |
| Парткод: | 302LC31511 |
| Деталь: | PLATE DC MOTOR 10 |
| Парткод: | 302K902610 |
| Деталь: | WORM WHEEL Z56L-Z20S |
| Парткод: | 302K931760 |
| Деталь: | SHAFT CONT DRIVE |
| Парткод: | 302K931780 |
| Деталь: | GEAR Z34S JOINT |
| Парткод: | 302K931830 |
| Деталь: | PLATE CONT DRIVE |
| Парткод: | 302K931720 |
| Деталь: | PARTS PWB RFID ASSY SP |
| Парткод: | 302K394070 |
| Деталь: | SPRING PADDLE CONT D |
| Парткод: | 302H731650 |
| Деталь: | COUPLING CONT D |
| Парткод: | 302H731640 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | WIRE CONTAINER MOTOR |
| Парткод: | 302LF46350 |
| Деталь: | WIRE FEED POWER |
| Парткод: | 302K946930 |
| Деталь: | GEAR Z35S |
| Парткод: | 302K903130 |
| Деталь: | GEAR Z20S JOINT FEED B |
| Парткод: | 302H006120 |
| Деталь: | GEAR Z20S |
| Парткод: | 302LC03130 |
| Деталь: | GEAR Z30S COUPLING |
| Парткод: | 302LC03140 |
| Деталь: | GEAR Z18S |
| Парткод: | 302K903140 |
| Деталь: | MOUNT DRIVE |
| Парткод: | 302LC03160 |
| Деталь: | SPRING COUPLING |
| Парткод: | 302LC03200 |
| Деталь: | PLATE DRIVE |
| Парткод: | 302LC03170 |
| Деталь: | BUSHING 6,REGISTRATION |
| Парткод: | 2BC06520 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | SHAFT DRIVE C |
| Парткод: | 302LH03150 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | PARTS FEED DRIVE H UNIT SP |
| Парткод: | 302N493030 |
| Деталь: | PARTS CONT DRIVE UNIT K SP |
| Парткод: | 302LF94080 |
| Деталь: | GEAR Z28 FEED |
| Парткод: | 302N406170 |
| Деталь: | PULLEY FEED |
| Парткод: | 302N406030 |
| Цена: | 440 ₽ |
| Деталь: | GEAR Z32 FEED OW |
| Парткод: | 302N406100 |
| Деталь: | GEAR Z32 PICKUP |
| Парткод: | 302N406110 |
| Деталь: | SPRING SWITCHBACK |
| Парткод: | 302LC28240 |
| Деталь: | PLATE FRAME UPPER |
| Парткод: | 302N406010 |
| Деталь: | PLATE FRAME LOWER |
| Парткод: | 302N406020 |
| Деталь: | ACTUATOR PAPER EMPTY |
| Парткод: | 302K906321 |
| Деталь: | SHAFT FEED PRIMARY B |
| Парткод: | 302N406210 |
| Деталь: | PARTS ROLLER ASSIST SP |
| Парткод: | 302K994420 |
| Деталь: | SHAFT RETARD |
| Парткод: | 302N406090 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | COUPLING DRIVE |
| Парткод: | 302K931530 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 302K994580 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | PULLEY RETARD |
| Парткод: | 302N406040 |
| Цена: | 450 ₽ |
| Деталь: | LEVER RETARD LOCK |
| Парткод: | 302N406160 |
| Деталь: | PLATE RETARD ADJUST |
| Парткод: | 302K906420 |
| Деталь: | SPRING LOCK MPF |
| Парткод: | 302F708310 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | HOLDER PULLEY |
| Парткод: | 302K906700 |
| Деталь: | PULLEY DU LOW |
| Парткод: | 302F929260 |
| Деталь: | SHAFT ASSIST PULLEY |
| Парткод: | 302K906710 |
| Деталь: | HOLDER RETARD |
| Парткод: | 302K906151 |
| Деталь: | BUSH 6 |
| Парткод: | 302K324450 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | LOWER BUSHING,PAPER FEED |
| Парткод: | 34806040 |
| Деталь: | TORQUE-LIMITER 390 |
| Парткод: | 302K906750 |
| Деталь: | PLATE RETARD HOLDER |
| Парткод: | 302K906300 |
| Деталь: | FULCRUM-PIN RETARD |
| Парткод: | 302N406150 |
| Деталь: | LEVER RETARD RELEASE |
| Парткод: | 302N406130 |
| Деталь: | SPRING RETARD |
| Парткод: | 302N406200 |
| Деталь: | SHEET PRIMARY FEED HI |
| Парткод: | 302K906721 |
| Деталь: | GUIDE PRIM FEED WIRE |
| Парткод: | 302K906250 |
| Деталь: | WIRE PRIMARY FEED UNIT |
| Парткод: | 302N446280 |
| Деталь: | GUIDE FRONT LOWER |
| Парткод: | 302N406060 |
| Деталь: | SPRING RETARD LOCK |
| Парткод: | 302N406140 |
| Деталь: | HOLDER SENSOR FEED |
| Парткод: | 302K906290 |
| Деталь: | SPONGE WIRE MPT |
| Парткод: | 302H708150 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | HOLDER PICKUP |
| Парткод: | 302N406050 |
| Деталь: | PIN PICK UP IDLE |
| Парткод: | 302K906080 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | SHAFT PICKUP PRIMARY |
| Парткод: | 302N406070 |
| Деталь: | ONEWAY-CLUTCH 6 |
| Парткод: | 302N406120 |
| Деталь: | SPRING PICK UP |
| Парткод: | 302K906260 |
| Деталь: | PLATE PRIMARY FEED DRIVE |
| Парткод: | 302K906111 |
| Деталь: | COUPLING PRIMARY FEED DRIVE |
| Парткод: | 302K906140 |
| Деталь: | MOUNT PRIMARY FEED R |
| Парткод: | 302K906270 |
| Деталь: | HOLDER PRIM FEED PULLEY |
| Парткод: | 302K906280 |
| Деталь: | SHAFT FEED LOW |
| Парткод: | 302K906510 |
| Деталь: | SHEET SOLENOID |
| Парткод: | 303NF06350 |
| Деталь: | GUIDE PRIMARY FEED |
| Парткод: | 302K906051 |
| Деталь: | CUSHION,CONTACT GLASS |
| Парткод: | 29812291 |
| Деталь: | MOUNT PRIMARY FEED |
| Парткод: | 302K906100 |
| Деталь: | PARTS PRIMARY FEED UNIT HI SP |
| Парткод: | 302N494020 |
| Цена: | 14 600 ₽ |
| Деталь: | PARTS GUIDE PRIMARY FEED SET SP |
| Парткод: | 302K994B90 |
| Деталь: | GUIDE FEED LOW |
| Парткод: | 302K906610 |
| Деталь: | SPRING TENSION |
| Парткод: | 2DC12170 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | HOLDER FEED LOW PULLEY |
| Парткод: | 302K906640 |
| Деталь: | SHAFT FEED LOW |
| Парткод: | 302K906510 |
| Деталь: | PULLEY MIDDLE A |
| Парткод: | 302H722760 |
| Деталь: | COVER FEED LOW |
| Парткод: | 302K906600 |
| Деталь: | LID SIDE FEED |
| Парткод: | 302K906691 |
| Деталь: | SHAFT FEED LOW HOOK |
| Парткод: | 302K906681 |
| Деталь: | HANDLE FEED LOW |
| Парткод: | 302K906660 |
| Деталь: | HOOK FEED LOW |
| Парткод: | 302K906670 |
| Деталь: | SPRING LID |
| Парткод: | 302FZ20021 |
| Деталь: | BAND B |
| Парткод: | 2BG06480 |
| Деталь: | PLATE FEED LOW |
| Парткод: | 302K906500 |
| Деталь: | PARTS ROLLER FEED LOW SP |
| Парткод: | 302K994430 |
| Деталь: | BUSH 8 |
| Парткод: | 28107310 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000006+H01 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | WIRE GUIDE FEED LOW |
| Парткод: | 302K946430 |
| Деталь: | ACTUATOR FEED LOW |
| Парткод: | 302K906560 |
| Деталь: | SPRING FEED ACT |
| Парткод: | 302K906520 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | GUIDE WIRE FEED LOW |
| Парткод: | 302LC06210 |
| Деталь: | PARTS PAD ROLLER SET SP |
| Парткод: | 302K994D70 |
| Деталь: | SPRING HV |
| Парткод: | 302K939360 |
| Деталь: | PLATE HV |
| Парткод: | 302K924620 |
| Деталь: | SHAFT DRIVE MIDDLE |
| Парткод: | 302N224010 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | BRACKET KEY MIDDLE B |
| Парткод: | 302LC24050 |
| Деталь: | BRACKET KEY MIDDLE C |
| Парткод: | 302LK24020 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | GEAR Z27L Z24L |
| Парткод: | 302K924690 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PARTS ROLLER MIDDLE L SP |
| Парткод: | 302LC94550 |
| Деталь: | PARTS MOTOR HB MID SP |
| Парткод: | 302K994310 |
| Деталь: | PLATE MIDDLE MOUNT B |
| Парткод: | 302LC24040 |
| Деталь: | PLATE MIDDLE MOUNT |
| Парткод: | 302LK24010 |
| Деталь: | BUSH 6 |
| Парткод: | 302K324450 |
| Деталь: | GEAR Z20S |
| Парткод: | 302K924600 |
| Деталь: | GEAR Z19S IDLE |
| Парткод: | 302K924640 |
| Деталь: | GEAR Z47R Z14S |
| Парткод: | 302LC24030 |
| Деталь: | FRAME MIDDLE FEED |
| Парткод: | 302K924530 |
| Деталь: | PARTS CLUTCH 50 Z35R SP |
| Парткод: | 303M894090 |
| Деталь: | PLATE EARTH MIDDLE |
| Парткод: | 302K924570 |
| Деталь: | WIRE GUIDE FEED MIDDLE |
| Парткод: | 302K946451 |
| Деталь: | WIRE GUIDE FEED MIDDLE |
| Парткод: | 302LK46451 |
| Деталь: | SWITCH REGISTRATION |
| Парткод: | 2FG27110 |
| Деталь: | HOLDER SENSOR MIDDLE |
| Парткод: | 302K924870 |
| Деталь: | SENSOR,CONVEYING |
| Парткод: | 3H327410 |
| Деталь: | HOLDER SENSOR REGIST |
| Парткод: | 302K924861 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | FILM FEED UPPER |
| Парткод: | 302LF33580 |
| Деталь: | SHEET COVER SENSOR |
| Парткод: | 302K924890 |
| Деталь: | SHEET REGIST L C |
| Парткод: | 302K924881 |
| Деталь: | SHEET REGIST L A |
| Парткод: | 302K924560 |
| Деталь: | MOUNT CLEANER REGIST |
| Парткод: | 302LF24140 |
| Деталь: | SPACER FRAME REAR |
| Парткод: | 302LF22590 |
| Деталь: | SHEET PROTECTOR TONER F |
| Парткод: | 302LF22650 |
| Деталь: | SHEET PROTECTOR TONER R |
| Парткод: | 302LF22660 |
| Деталь: | PARTS ROLLER REGIST H SP |
| Парткод: | 302K994A00 |
| Деталь: | PARTS ROLLER REGIST L SP |
| Парткод: | 302K994450 |
| Деталь: | STOPPER 8 |
| Парткод: | 302K921120 |
| Деталь: | GEAR Z24L |
| Парткод: | 302K924510 |
| Деталь: | PARTS CLUTCH 50 Z35R SP |
| Парткод: | 302KV44041 |
| Цена: | 900 ₽ |
| Деталь: | BEARING 696ZZNR |
| Парткод: | 7BE006155J31H01 |
| Деталь: | GEAR Z60L |
| Парткод: | 302LC31750 |
| Деталь: | PARTS CLEANER REGIST ASSY SP |
| Парткод: | 302LF94160 |
| Цена: | 3 500 ₽ |
| Деталь: | PLATE MIDDLE FEED |
| Парткод: | 302K924542 |
| Деталь: | PARTS REGIST GUIDE ASSY SP |
| Парткод: | 302LC94680 |
| Деталь: | GUIDE TRANSFER FRONT A |
| Парткод: | 302LF22070 |
| Деталь: | SPACER FRAME FRONT |
| Парткод: | 302LF22580 |
| Деталь: | PARTS GUIDE FEED MIDDLE ASSY SP |
| Парткод: | 302K994131 |
| Деталь: | PARTS GUIDE FEED REGIST ASSY SP |
| Парткод: | 302N994020 |
| Деталь: | PARTS GUIDE FEED REGIST ASSY SP |
| Парткод: | 302NB94020 |
| Деталь: | PARTS REGIST GUIDE SET SP |
| Парткод: | 302LC94691 |
| Деталь: | CASE TONER HOPPER |
| Парткод: | 302LF15012 |
| Деталь: | SPONGE HOPPER A |
| Парткод: | 302LF15170 |
| Деталь: | SPONGE HOPPER B |
| Парткод: | 302K915360 |
| Деталь: | CAP TONER |
| Парткод: | 302K915470 |
| Деталь: | OIL SEAL |
| Парткод: | 302KY12020 |
| Деталь: | SCREW TONER SUPPLY |
| Парткод: | 302K915070 |
| Деталь: | CAP SCREW |
| Парткод: | 302FZ23260 |
| Деталь: | SEAL HOPPER LOW |
| Парткод: | 302K915381 |
| Деталь: | SHUTTER HOPPER LOW |
| Парткод: | 302K915230 |
| Деталь: | SPRING PIPE LOW |
| Парткод: | 302H703140 |
| Деталь: | TONER EMPTY DETECTION SENSOR |
| Парткод: | 3033915181 |
| Деталь: | PADDLE TONER SUPPLY A |
| Парткод: | 302K915110 |
| Деталь: | PADDLE TONER SUPPLY B |
| Парткод: | 302K915120 |
| Деталь: | SPRING TONER SENSOR A |
| Парткод: | 302K915390 |
| Деталь: | GEAR Z15S IDLE |
| Парткод: | 302LF15030 |
| Деталь: | GEAR Z60S |
| Парткод: | 302LF15070 |
| Деталь: | GEAR Z30S |
| Парткод: | 302K915180 |
| Деталь: | LID TONER HOPPER |
| Парткод: | 302LF15020 |
| Деталь: | SEAL HOPPER UP |
| Парткод: | 302K915370 |
| Деталь: | SHUTTER HOPPER UP |
| Парткод: | 302K915460 |
| Деталь: | BUSHING, TRANSFER |
| Парткод: | 2A116180 |
| Деталь: | SHAFT DRIVE |
| Парткод: | 302K915330 |
| Деталь: | GEAR Z14S |
| Парткод: | 302K915400 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | SHAFT TONER SUPPLY |
| Парткод: | 302LF15050 |
| Деталь: | BUSH SCREW |
| Парткод: | 302K915450 |
| Деталь: | GEAR Z21S-Z15S |
| Парткод: | 302K915160 |
| Деталь: | GEAR Z32R-Z14S |
| Парткод: | 302K915210 |
| Деталь: | GEAR Z21S |
| Парткод: | 302K915200 |
| Деталь: | GEAR Z48L |
| Парткод: | 302K915190 |
| Деталь: | GEAR Z32L |
| Парткод: | 302K915080 |
| Деталь: | MOUNT PI |
| Парткод: | 302K921410 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | PARTS CONV RELEASE MOTOR ASSY SP |
| Парткод: | 302LC94190 |
| Деталь: | HOLDER TONER MOTOR |
| Парткод: | 302LF15080 |
| Деталь: | SEAL MOTOR DC |
| Парткод: | 302LC31511 |
| Деталь: | PLATE DC MOTOR 6 |
| Парткод: | 302K908660 |
| Деталь: | WIRE TONER LEVEL SENSOR |
| Парткод: | 302K946A80 |
| Деталь: | PLATE INNER FRAME |
| Парткод: | 302LF03021 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210003++H01 |
| Деталь: | LEVER HOOK |
| Парткод: | 302LF03080 |
| Деталь: | SPRING LEVER L |
| Парткод: | 302LF03410 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | SPRING LEVER R |
| Парткод: | 302LF03400 |
| Деталь: | DUCT DLP |
| Парткод: | 302LF03250 |
| Деталь: | SEAL DUCT DLP A |
| Парткод: | 302LF03900 |
| Деталь: | WIRE RETAINER B |
| Парткод: | 302LH46220 |
| Деталь: | WIRE RETAINER |
| Парткод: | 302NB46010 |
| Деталь: | FILM WIRE A |
| Парткод: | 302LH03100 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | PARTS FAN COOLING LSU 60 SP |
| Парткод: | 302LC94380 |
| Деталь: | SPONGE FAN |
| Парткод: | 302K903250 |
| Деталь: | SHEET DUCT DLP |
| Парткод: | 302LF03070 |
| Деталь: | SCREW FAN |
| Парткод: | 302H733430 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | SEAL INNER COOLING C |
| Парткод: | 302LC33540 |
| Деталь: | SEAL DUCT DLP B |
| Парткод: | 302LF03910 |
| Деталь: | DUCT DRUM |
| Парткод: | 302LF03371 |
| Деталь: | LEVER CASS SHUTTER |
| Парткод: | 302LF03011 |
| Деталь: | LID DRUM DUCT |
| Парткод: | 302LF03380 |
| Деталь: | WORK PLATE CASS |
| Парткод: | 302LF03460 |
| Деталь: | NUT FUSER A /FS-1800/3800 A4 |
| Парткод: | 5MMS111SL002 |
| Деталь: | COVER INNER |
| Парткод: | 302LH03041 |
| Деталь: | SEAL DUCT DLP D |
| Парткод: | 302LH03600 |
| Деталь: | COVER FILTER DLP |
| Парткод: | 302LF03440 |
| Деталь: | FILTER DUCT DLP |
| Парткод: | 302LF03450 |
| Деталь: | COVER FILTER DRUM |
| Парткод: | 302LF03420 |
| Деталь: | FILTER DUCT DRUM |
| Парткод: | 302LF03430 |
| Деталь: | SEAL DUCT DRUM A |
| Парткод: | 302LF03930 |
| Деталь: | SEAL DUCT DRUM B |
| Парткод: | 302LF03940 |
| Деталь: | SEAL INNER |
| Парткод: | 302LF03991 |
| Деталь: | FILM INNER FRAME |
| Парткод: | 302LF03281 |
| Деталь: | SEAL COOLING FAN A |
| Парткод: | 302K903860 |
| Деталь: | SEAL COOLING FAN B |
| Парткод: | 302K903870 |
| Деталь: | PARTS INNER UNIT SP |
| Парткод: | 302LH94033 |
| Деталь: | PARTS INNER UNIT SP |
| Парткод: | 302NB94010 |
| Деталь: | SLIDER CASSETTE RIGHT |
| Парткод: | 302N209500 |
| Деталь: | CAP HANDLE |
| Парткод: | 302FZ02580 |
| Деталь: | SEAL HANDLE |
| Парткод: | 302FZ03110 |
| Деталь: | SLIDER CASSETTE LEFT |
| Парткод: | 302N209510 |
| Деталь: | MOUNT SLIDER LF |
| Парткод: | 302N209530 |
| Деталь: | MOUNT SLIDER LR |
| Парткод: | 302N209540 |
| Деталь: | SLIDER CONVEYING |
| Парткод: | 302K924300 |
| Деталь: | MOUNT SLIDER CONVEYING |
| Парткод: | 302K924311 |
| Деталь: | MOUNT CONVEYING |
| Парткод: | 302LH29020 |
| Деталь: | MOUNT CONVEYING |
| Парткод: | 302LL29020 |
| Деталь: | FRAME FRONT FUSER A |
| Парткод: | 302LC02152 |
| Деталь: | NUT ADJUST |
| Парткод: | 302LC02270 |
| Деталь: | HOLDER FUSER ADJUST |
| Парткод: | 302LC02240 |
| Деталь: | MOUNT FUSER ADJUST |
| Парткод: | 302LC02250 |
| Деталь: | Plate Fuser |
| Парткод: | 302FZ02720 |
| Деталь: | STAY UPPER TOP RIGHT |
| Парткод: | 302LC02221 |
| Деталь: | ADJUSTER SCANNER |
| Парткод: | 302K902950 |
| Деталь: | MOUNT RUBBER SCANNER |
| Парткод: | 302K902960 |
| Деталь: | GROUND SCANNER REAR |
| Парткод: | 302H017310 |
| Деталь: | PIN ROLLER RELEASE LEVER |
| Парткод: | 302FB16320 |
| Деталь: | STAY ISU TOP LEFT |
| Парткод: | 302N402010 |
| Деталь: | FRAME FUSER UNIT |
| Парткод: | 302LH02170 |
| Деталь: | PLATE SEPARATE FUSER |
| Парткод: | 302LH02100 |
| Деталь: | PARTITION FIXING HEAT |
| Парткод: | 302LH33030 |
| Деталь: | SHEET COVER PWB FEED |
| Парткод: | 302K902990 |
| Деталь: | FILM BASE CASSETTE |
| Парткод: | 302K902571 |
| Деталь: | RAIL EXIT REAR |
| Парткод: | 302K902850 |
| Деталь: | PLATAE EARTH |
| Парткод: | 302LC28200 |
| Деталь: | LEVER RELEASE FUSER DRIVE |
| Парткод: | 302K931690 |
| Деталь: | SPRING LEVER RELEASE |
| Парткод: | 302K931980 |
| Деталь: | PLATE SHIELD BOX |
| Парткод: | 302K939080 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210003++H01 |
| Деталь: | RAIL CONTAINER L |
| Парткод: | 302LC03370 |
| Деталь: | RAIL CONTAINER R |
| Парткод: | 302LH03720 |
| Деталь: | FILM RAIL CONTAINER |
| Парткод: | 302LH33150 |
| Деталь: | PIN HOOK |
| Парткод: | 302K924450 |
| Деталь: | SHEET SEPARATE FUSER COOLING |
| Парткод: | 302LH33020 |
| Деталь: | FRAME FRONT FUSER B |
| Парткод: | 302LC02160 |
| Деталь: | PLATE MOUNT DP |
| Парткод: | 302K902250 |
| Деталь: | BASE RUBBER,SCANNER SECTION |
| Парткод: | 2AV12280 |
| Деталь: | GROUND BASE SCANNER |
| Парткод: | 302H017380 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | PLATE KEY MIDDLE B |
| Парткод: | 302LC24060 |
| Деталь: | PLATE KEY MIDDLE C |
| Парткод: | 302LK24030 |
| Деталь: | PROTECTOR PLATE HANDLE |
| Парткод: | 302LC02810 |
| Деталь: | HANDLE RIGHT |
| Парткод: | 302LC02561 |
| Деталь: | SHAFT HOOK PULLEY |
| Парткод: | 302K909630 |
| Деталь: | LEVER CASSETTE HOOK |
| Парткод: | 302K909640 |
| Деталь: | SPRING CASSETTE HOOK |
| Парткод: | 302LH02050 |
| Деталь: | PULLEY EJECT |
| Парткод: | 303LW24060 |
| Деталь: | SHAFT HOOK FULCRUM |
| Парткод: | 303NF02280 |
| Деталь: | HOLDER DECK HOOK |
| Парткод: | 303NF02301 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | SHEET LEFT READING |
| Парткод: | 303M424200 |
| Деталь: | STAY CASSETTE FRONT |
| Парткод: | 302N209520 |
| Деталь: | SHEET FRAME FUSER F |
| Парткод: | 302KA02120 |
| Деталь: | RETAINING PIN TRAY |
| Парткод: | 303H321080 |
| Деталь: | PARTS SLIDER CASSETTE LEFT ASSY SP |
| Парткод: | 302N294020 |
| Деталь: | Control-panel assembly (Western) |
| Парткод: | 302N994011 |
| Цена: | 32 400 ₽ |
| Деталь: | Formatter, exchange, HP Color LaserJet 3000dn and 3000dtn Series only (256 MB) |
| Парткод: | 302N994041 |
| Цена: | 56 700 ₽ |
| Деталь: | Печь, в сборе (220В) |
| Парткод: | FK-6307B |
| Цена: | 22 800 ₽ |
| Деталь: | FILM RETARD |
| Парткод: | 302K908610 |
| Деталь: | BASE MPF LOWER |
| Парткод: | 302K908021 |
| Деталь: | ACTUATOR FEED MPF |
| Парткод: | 302K908280 |
| Деталь: | SPRING ACTUATOR BYPASS |
| Парткод: | 302FZ22870 |
| Деталь: | HOLDER RETARD MPF |
| Парткод: | 302K908240 |
| Деталь: | FELT DUPLEX |
| Парткод: | 3H610240 |
| Деталь: | SHAFT RETARD MPF B |
| Парткод: | 302K908501 |
| Деталь: | JOINT RETARD DRIVE |
| Парткод: | 302K906180 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | GEAR RETARD MPF Z24L |
| Парткод: | 302K908420 |
| Деталь: | SHAFT RETARD MPF A |
| Парткод: | 302K908491 |
| Деталь: | SHAFT RETARD MPF |
| Парткод: | 302LC08030 |
| Деталь: | PULLEY,SEPARATION |
| Парткод: | 2AR07230 |
| Цена: | 360 ₽ |
| Деталь: | TORQUE-LIMITER 390 |
| Парткод: | 302K906750 |
| Деталь: | TORQUE-LIMITER 360 |
| Парткод: | 302GR06110 |
| Деталь: | SPRING RETARD MPF |
| Парткод: | 302K908540 |
| Деталь: | SPRING RETARD MPF |
| Парткод: | 302LC08040 |
| Деталь: | COUPLING PRIMARY FEED DRIVE |
| Парткод: | 302K906140 |
| Деталь: | PULLEY FACE UP |
| Парткод: | 302F925160 |
| Деталь: | SPRING HOLDER PULLEY |
| Парткод: | 302K924770 |
| Деталь: | BASE MPF UPPER |
| Парткод: | 302K908012 |
| Деталь: | HOLDER MIDDLE PULLEY |
| Парткод: | 302K908250 |
| Деталь: | SPRING MIDDLE |
| Парткод: | 302LF08010 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | SHAFT FEED |
| Парткод: | 302K324460 |
| Деталь: | PULLEY MIDDLE A |
| Парткод: | 302H722760 |
| Деталь: | SPRING MIDDLE R |
| Парткод: | 302K908700 |
| Деталь: | GEAR FEED Z26H |
| Парткод: | 302F906030 |
| Деталь: | SHAFT PICKUP MPF |
| Парткод: | 302K908300 |
| Деталь: | GEAR Z30R PICKUP |
| Парткод: | 302K908350 |
| Деталь: | PARTS GEAR Z30R ONE-WAY SP |
| Парткод: | 302K994540 |
| Деталь: | PULLEY,PAPER FEED |
| Парткод: | 2AR07220 |
| Цена: | 1 600 ₽ |
| Деталь: | SHAFT FEED MPF A |
| Парткод: | 302K908471 |
| Деталь: | JOINT DRIVE |
| Парткод: | 302FB06151 |
| Деталь: | SPRING PICKUP MPF |
| Парткод: | 302K908530 |
| Деталь: | HOLDER FEED MPF |
| Парткод: | 302K908230 |
| Деталь: | ACTUATOR PAPER SET |
| Парткод: | 302K908290 |
| Деталь: | SPRING PAPER SET |
| Парткод: | 302K908570 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | MOUNT PI |
| Парткод: | 302K908460 |
| Деталь: | WIRE MPF |
| Парткод: | 302K946370 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | SHAFT FEED MPF B |
| Парткод: | 302K908480 |
| Деталь: | GUIDE DU LOWER |
| Парткод: | 302K908320 |
| Деталь: | CASE LIFT MOTOR A |
| Парткод: | 302K908261 |
| Деталь: | PARTS MPT LIFT MOTOR ASSY SP |
| Парткод: | 302LC94200 |
| Деталь: | PLATE DC MOTOR 6 |
| Парткод: | 302K908660 |
| Деталь: | GEAR Z46S-Z18S |
| Парткод: | 302K908370 |
| Деталь: | WORM-WHEEL 36 Z18S |
| Парткод: | 302K908360 |
| Деталь: | GEAR LIFT Z25S |
| Парткод: | 302K908390 |
| Деталь: | GEAR LIFT Z64S |
| Парткод: | 302K908380 |
| Деталь: | LEVER LIFT |
| Парткод: | 302K908310 |
| Деталь: | GEAR RETARD MPF Z17L |
| Парткод: | 302K908410 |
| Деталь: | PIN RETARD MPF |
| Парткод: | 302K908450 |
| Деталь: | GEAR Z27R ONEWAY |
| Парткод: | 303LL31440 |
| Деталь: | COVER CLUTCH |
| Парткод: | 302K908270 |
| Деталь: | PARTS CLUTCH 50 Z35R SP |
| Парткод: | 303M894090 |
| Деталь: | DAMPER MPF B |
| Парткод: | 302K908630 |
| Деталь: | DAMPER MPF A |
| Парткод: | 302K908620 |
| Деталь: | SPRING DAMPER |
| Парткод: | 302K908640 |
| Деталь: | GUIDE MIDDLE MPF |
| Парткод: | 302K908440 |
| Деталь: | SHEET MPF F |
| Парткод: | 302N408010 |
| Деталь: | SHEET MPF R |
| Парткод: | 302N408020 |
| Деталь: | FILM MIDDLE GUIDE |
| Парткод: | 302K908590 |
| Деталь: | FILM DU GUIDE B |
| Парткод: | 302K908692 |
| Деталь: | COVER DU |
| Парткод: | 302K929070 |
| Деталь: | GUIDE COVER DU |
| Парткод: | 302K929080 |
| Деталь: | LID FILTER DU |
| Парткод: | 302K929380 |
| Деталь: | PARTS MPT ASSY SP |
| Парткод: | 302K994012 |
| Деталь: | PARTS MPT ASSY SP |
| Парткод: | 302LC94022 |
| Деталь: | PARTS COVER GUIDE DU L ASSY SP |
| Парткод: | 302LC94470 |
| Деталь: | STOPPER BYPASS TABLE |
| Парткод: | 2FB07330 |
| Деталь: | PARTS PWB MPF SIZE ASSY SP |
| Парткод: | 302K994620 |
| Деталь: | TRAY MPF A |
| Парткод: | 302K908030 |
| Деталь: | TRAY MPF B |
| Парткод: | 302K908040 |
| Деталь: | TRAY MPF C |
| Парткод: | 302K908050 |
| Деталь: | TRAY MPF D |
| Парткод: | 302K908060 |
| Деталь: | RACK CURSOR MPF |
| Парткод: | 302K908120 |
| Деталь: | ACTUATOR SIZE DETECTION |
| Парткод: | 302K908211 |
| Деталь: | TERMINAL PAPER SIZE |
| Парткод: | 3HL06110 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000006+H01 |
| Деталь: | LABEL MPF CAUTION A |
| Парткод: | 302LC34061 |
| Деталь: | LABEL MPF PAPER LIMIT |
| Парткод: | 302LC34080 |
| Деталь: | SPRING-COMPRESSION LIFT |
| Парткод: | 302K908200 |
| Деталь: | SHAFT LIFT MPF |
| Парткод: | 302K908190 |
| Деталь: | ARM LIFT A |
| Парткод: | 302K908130 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | ARM LIFT B |
| Парткод: | 302K908140 |
| Деталь: | HOLDER MPF TABLE |
| Парткод: | 302K908650 |
| Деталь: | SPRING PF |
| Парткод: | 303LL07471 |
| Деталь: | SPRING-TORSION SIZE DETECTION |
| Парткод: | 302K908220 |
| Деталь: | HOLDER SIZE DETECTION |
| Парткод: | 302K908580 |
| Деталь: | GUIDE WIRE TRAY |
| Парткод: | 302K908160 |
| Деталь: | WIRE MPF SIZE DETECTION |
| Парткод: | 302K946600 |
| Деталь: | SPONGE WIRE MPT |
| Парткод: | 302H708150 |
| Деталь: | BASE LIFT |
| Парткод: | 302K908080 |
| Деталь: | PAD BOTTOM |
| Парткод: | 302F909210 |
| Деталь: | WIRE MPF TRAY |
| Парткод: | 302K946380 |
| Деталь: | SPRING DRUM JOINT |
| Парткод: | 302H712650 |
| Деталь: | CURSOR MPF R |
| Парткод: | 302K908110 |
| Деталь: | CURSOR MPF F |
| Парткод: | 302K908100 |
| Деталь: | COVER CURSOR |
| Парткод: | 302K908090 |
| Деталь: | IDLE GEAR 40,TONER SUPPLY |
| Парткод: | 65815060 |
| Деталь: | SEAL FRAME ISU |
| Парткод: | 302K917100 |
| Деталь: | LABEL MPF SIZE INDICATOR IN |
| Парткод: | 302LC34100 |
| Деталь: | LABEL MPF SIZE INDICATOR ME |
| Парткод: | 302LC34090 |
| Деталь: | PARTS MPT TRAY UNIT SP |
| Парткод: | 302K994051 |
| Деталь: | Ремень подачи бумаги в автоподатчике документов |
| Парткод: | 303LL07531 |
| Цена: | 1 900 ₽ |
| Деталь: | GEAR GUIDE SIDE |
| Парткод: | 302BM07410 |
| Деталь: | RACK CURSOR |
| Парткод: | 302K909060 |
| Деталь: | PARTS GEAR CURSOR SP |
| Парткод: | 302K994550 |
| Деталь: | ACTUATOR PAPER LEVEL DETECTION |
| Парткод: | 302K909270 |
| Деталь: | LABEL PAPER SIZE A |
| Парткод: | 302K934011 |
| Деталь: | LABEL PAPER SIZE B |
| Парткод: | 302K934021 |
| Деталь: | LIFT LOCK |
| Парткод: | 302GR09991 |
| Деталь: | LABEL CASSETTE PAPER MAX |
| Парткод: | 302K934090 |
| Деталь: | LABEL CASSETTE CURSOR LOCK |
| Парткод: | 302K934100 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | CASSETTE BASE |
| Парткод: | 302N209010 |
| Деталь: | CUSHION,CASSETTE WORK PLATE |
| Парткод: | 33907210 |
| Деталь: | ARM SIZE DETECTION |
| Парткод: | 302N209030 |
| Деталь: | LABEL CASSETTE OPERATION |
| Парткод: | 302K934030 |
| Деталь: | CURSOR END |
| Парткод: | 302N209020 |
| Деталь: | PLATE WORK |
| Парткод: | 302K909090 |
| Деталь: | SHAFT WORK PLATE |
| Парткод: | 302K909190 |
| Деталь: | CAP TURN PLATE |
| Парткод: | 302K909140 |
| Деталь: | SPRING EXIT PULLEY |
| Парткод: | 302H728100 |
| Деталь: | LEVER SIDE SW |
| Парткод: | 302K909251 |
| Деталь: | SPRING DU |
| Парткод: | 302FZ29131 |
| Деталь: | CAM CURSOR RAIL |
| Парткод: | 302K909100 |
| Деталь: | CURSOR REAR |
| Парткод: | 302K909041 |
| Деталь: | RAIL CURSOR |
| Парткод: | 302K909021 |
| Деталь: | LEVER CURSOR LOCK REAR |
| Парткод: | 302K909121 |
| Деталь: | LOCK REAR CURSOR |
| Парткод: | 302K909151 |
| Деталь: | SHAFT CURSOR GEAR |
| Парткод: | 302K909131 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | CURSOR FRONT |
| Парткод: | 302K909031 |
| Деталь: | LEVER CURSOR |
| Парткод: | 302K909050 |
| Деталь: | SPRING LOOP SOLENOID |
| Парткод: | 303JC02050 |
| Деталь: | LABEL SET PAPER |
| Парткод: | 302K934040 |
| Деталь: | PAD BOTTOM |
| Парткод: | 302K909260 |
| Деталь: | LABEL CASSETTE NUMBER 1 |
| Парткод: | 302K934050 |
| Деталь: | LABEL CASSETTE NUMBER 2 |
| Парткод: | 302K934060 |
| Деталь: | HANDLE CASSETTE |
| Парткод: | 302LC04380 |
| Деталь: | EMBLEM CASSETTE |
| Парткод: | 302LC04390 |
| Деталь: | COVER CASSETTE A |
| Парткод: | 302N404200 |
| Деталь: | COVER CASSETTE B |
| Парткод: | 302N404210 |
| Деталь: | SHEET CASSETTE PAPER SIZE A |
| Парткод: | 302K934700 |
| Деталь: | SHEET CASSETTE PAPER SIZE B |
| Парткод: | 302K934710 |
| Деталь: | SHEET CASSETTE PAPER MEDIA KL-A |
| Парткод: | 302K934730 |
| Деталь: | SHEET CASSETTE PAPER MEDIA KL-B |
| Парткод: | 302K934740 |
| Деталь: | SHEET CASSETTE PAPER MEDIA KL-C |
| Парткод: | 302K934750 |
| Деталь: | SHEET CASSETTE PAPER MEDIA KL-D |
| Парткод: | 302K934760 |
| Деталь: | SHEET CASSETTE PAPER MEDIA KL-E |
| Парткод: | 302K934770 |
| Деталь: | CT-8706 |
| Парткод: | 302N293010 |
| Деталь: | PARTS PLATE PAPER BOTTOM UNIT SP |
| Парткод: | 302K994C20 |
| Деталь: | PARTS COVER CASSETTE A ASSY SP |
| Парткод: | 302N494040 |
| Деталь: | PARTS COVER CASSETTE B ASSY SP |
| Парткод: | 302N494050 |
| Деталь: | PULLEY MID /B-11 FRAME A4 |
| Парткод: | 2FM02210 |
| Деталь: | GEAR FD Z31 /B-11 FRAME A4 |
| Парткод: | 2FM02320 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | PULLEY DU LOW |
| Парткод: | 302F929260 |
| Деталь: | SPRING EXIT PUSH |
| Парткод: | 302FZ28270 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | GEAR Z23S EXIT |
| Парткод: | 302H728080 |
| Деталь: | SPRING PULLEY A |
| Парткод: | 302HN28120 |
| Деталь: | PULLEY MIDDLE |
| Парткод: | 302JF22010 |
| Деталь: | SPRING-TORSION SWITCHBACK |
| Парткод: | 302K928190 |
| Деталь: | PARTS MOTOR PM FEED SP |
| Парткод: | 302K994300 |
| Деталь: | PARTS SOLENOID FEED SHIFT SP |
| Парткод: | 302K994370 |
| Деталь: | PARTS ROLLEREXIT SP |
| Парткод: | 302LC94350 |
| Деталь: | PARTS GEAR Z40R Z14S IDLE SP |
| Парткод: | 302LC94360 |
| Деталь: | ACTUATOR EXIT SENSOR |
| Парткод: | 302LC28091 |
| Деталь: | SPRING-COMPRESSION |
| Парткод: | 302LC28100 |
| Деталь: | SPRING-EXTENSION |
| Парткод: | 302LC28110 |
| Деталь: | SPRING-COMPRESSION |
| Парткод: | 302LC28150 |
| Деталь: | ACTUATOR SWITCHBACK |
| Парткод: | 302LC28211 |
| Деталь: | WIRE EXIT |
| Парткод: | 302LC46360 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | STATIC ELIMINATOR,EJECT |
| Парткод: | 63212210 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | SPRING SWITCHBACK |
| Парткод: | 302LC28240 |
| Деталь: | FRAME EXIT LOWER |
| Парткод: | 302LC28011 |
| Деталь: | GUIDE CHANGE UPPER |
| Парткод: | 302LC28041 |
| Деталь: | GUIDE CHANGE LOWER |
| Парткод: | 302LC28051 |
| Деталь: | PLATE EARTH EXIT |
| Парткод: | 302LC28140 |
| Деталь: | GUIDE EXIT MIDDLE |
| Парткод: | 302LC28030 |
| Деталь: | CUSHION EJECT GUIDE B |
| Парткод: | 303JY28280 |
| Деталь: | SHAFT FEED |
| Парткод: | 302K324460 |
| Деталь: | EXIT PUSH |
| Парткод: | 302FZ28260 |
| Деталь: | PARTS ROLLER EXIT SP |
| Парткод: | 302LH94290 |
| Деталь: | GUIDE ACTUATOR |
| Парткод: | 302LC28221 |
| Деталь: | SHAFT GEAR BELT |
| Парткод: | 303MA16560 |
| Деталь: | PLATE EXIT F |
| Парткод: | 302LC28060 |
| Деталь: | COVER EXIT FRONT |
| Парткод: | 302LC28120 |
| Деталь: | FRAME EXIT UPPER |
| Парткод: | 302LC28023 |
| Деталь: | GUIDE EXIT PUSH |
| Парткод: | 302LH28010 |
| Деталь: | STAY EXIT LOW |
| Парткод: | 302LC28230 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | PARTS EXIT UNIT B SP |
| Парткод: | 302LH94272 |
| Деталь: | GEAR Z160R |
| Парткод: | 302K931030 |
| Деталь: | BEARING 6800ZZ(7MM) |
| Парткод: | 7BE010197431H01 |
| Деталь: | STOPPER 8 |
| Парткод: | 302K921120 |
| Деталь: | CUT-WASHER 8X17 |
| Парткод: | 302K931840 |
| Деталь: | HOLDER DRUM DRIVE |
| Парткод: | 302K931012 |
| Деталь: | PLATE DRUM DRIVE |
| Парткод: | 302K931021 |
| Деталь: | PLATE EARTH DRUM |
| Парткод: | 302K931070 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | PLATE MOTOR DRUM |
| Парткод: | 302K931100 |
| Деталь: | PARTS MOTOR-BL W20 DRUM Z11 SP |
| Парткод: | 302LC94461 |
| Деталь: | HOLDER BEARING SUPPORT |
| Парткод: | 302K931060 |
| Деталь: | SPRING DRUM JOINT |
| Парткод: | 302LC31070 |
| Деталь: | COUPLING DRUM |
| Парткод: | 302K931130 |
| Деталь: | SHAFT DRUM DRIVE |
| Парткод: | 302K931040 |
| Деталь: | WIRE DRUM MOT |
| Парткод: | 302LF46290 |
| Деталь: | BUSH DRUM DRIVE |
| Парткод: | 302N631050 |
| Деталь: | GEAR Z90R JOINT |
| Парткод: | 302K931620 |
| Деталь: | SPRING PADDLE CONT D |
| Парткод: | 302H731650 |
| Деталь: | JOINT FUSER DRIVE |
| Парткод: | 302K931640 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | CUT WASHER 5X10 |
| Парткод: | 302LC31640 |
| Деталь: | GEAR Z54S-Z26S |
| Парткод: | 302LC31620 |
| Деталь: | SPRING JOINT |
| Парткод: | 302K931660 |
| Деталь: | GEAR Z50S JOINT |
| Парткод: | 302K931630 |
| Деталь: | WIRE FUSER MOTOR |
| Парткод: | 302K946540 |
| Деталь: | PLATE FUSER DRIVE |
| Парткод: | 302LH31612 |
| Деталь: | GEAR Z30S |
| Парткод: | 302LH31620 |
| Деталь: | CUT WASHER |
| Парткод: | 5MVS665KB001 |
| Деталь: | PARTS MOTOR-BL W10 SP |
| Парткод: | 302LC94290 |
| Деталь: | PARTS MOTOR-BL W20 SP |
| Парткод: | 302K994321 |
| Деталь: | PLATE REGIST DRIVE |
| Парткод: | 302LH31010 |
| Деталь: | BUSHING,TRANSFER |
| Парткод: | 2A116180 |
| Деталь: | WIRE REGIST MOTOR |
| Парткод: | 302K946550 |
| Деталь: | MOUNT DRUM DRIVE |
| Парткод: | 302LF31630 |
| Деталь: | WIRE DLP MOT |
| Парткод: | 302LH46280 |
| Деталь: | PARTS MOTOR PM REGIST SP |
| Парткод: | 302K994980 |
| Деталь: | PARTS DRUM DRIVE H SP |
| Парткод: | 302N993020 |
| Деталь: | PARTS FUSER DRIVE UNIT SP |
| Парткод: | 302LH94102 |
| Деталь: | PARTS DLP MOTOR ASSY(G) SP |
| Парткод: | 302LH94110 |
| Деталь: | HOLDER FEED PULLEY |
| Парткод: | 302LC06090 |
| Деталь: | GEAR FEED Z26H |
| Парткод: | 302F906030 |
| Деталь: | PULLEY PICKUP ASSY |
| Парткод: | 302HN06080 |
| Цена: | 480 ₽ |
| Деталь: | SHAFT PRIMARY FEED |
| Парткод: | 302LC06150 |
| Деталь: | GEAR FEED Z30H OW |
| Парткод: | 302LC06160 |
| Деталь: | PULLEY FEED ASSY |
| Парткод: | 302F906230 |
| Цена: | 750 ₽ |
| Деталь: | FRAME PRIMARY UPPER |
| Парткод: | 302LC06020 |
| Деталь: | GUIDE PRIMARY FEED |
| Парткод: | 302LC06101 |
| Деталь: | BUSH FEED /A-49 FEED A4 |
| Парткод: | 5MVM176DN026 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | SPRING FEED PULLEY |
| Парткод: | 302LC06080 |
| Деталь: | PLATE FEED EARTH |
| Парткод: | 302LC06070 |
| Деталь: | SHAFT FEED PULLEY |
| Парткод: | 302LC06040 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | JOINT FEED PULLEY |
| Парткод: | 302LC06050 |
| Деталь: | RETARD ROLLER ASSY |
| Парткод: | 302F909171 |
| Цена: | 900 ₽ |
| Деталь: | HOLDER RETARD |
| Парткод: | 302LC06110 |
| Деталь: | PLATE PRIMARY LOW |
| Парткод: | 302LC06030 |
| Деталь: | SPRING RETARD |
| Парткод: | 302LC06121 |
| Деталь: | SHEET PRIMARY FEED |
| Парткод: | 302LC06180 |
| Деталь: | PLATE FRAME EARTH |
| Парткод: | 302LC06190 |
| Деталь: | WIRE PRIMARY FEED UNIT |
| Парткод: | 302LK46390 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302K994580 |
| Деталь: | HOLDER SENSOR FEED |
| Парткод: | 302K906290 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | ACTUATOR PAPER EMPTY |
| Парткод: | 302LC06061 |
| Деталь: | PARTS PRIMARY FEED UNIT LOW SP |
| Парткод: | 302LC94040 |
| Деталь: | Блок проявки |
| Парткод: | DV-6305 |
| Цена: | 22 000 ₽ |
| Деталь: | Узел переноса заряда в драм-картридже, в сборе |
| Парткод: | MC-6720 |
| Деталь: | Средняя направляющая узла подачи бумаги, в сборе |
| Парткод: | 302K994132 |
| Цена: | 4 900 ₽ |
| Деталь: | Узел первичной вертикальной подачи бумаги, в сборе |
| Парткод: | 302N494021 |
| Цена: | 14 700 ₽ |
| Деталь: | Крышка планшетного сканера |
| Парткод: | 1202H70UN0 |
| Цена: | 4 200 ₽ |
| Деталь: | FILM LCD WIRE |
| Парткод: | 302N405210 |
| Деталь: | CUSHION LCD |
| Парткод: | 302H705610 |
| Деталь: | SPONGE LCD B |
| Парткод: | 302K505280 |
| Деталь: | PARTS PWB OPERATION ASSY SP |
| Парткод: | 302N494180 |
| Деталь: | KEY MENU |
| Парткод: | 302N405080 |
| Деталь: | PARTS LCD OPERATION SP |
| Парткод: | 302N494090 |
| Деталь: | PARTS PWB PANEL MAIN ASSY SP |
| Парткод: | 302N494150 |
| Деталь: | COVER OPERATION A |
| Парткод: | 302N405010 |
| Деталь: | KEY 10 |
| Парткод: | 302LC05050 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | KEY FUNCTION |
| Парткод: | 302N405070 |
| Деталь: | SHEET WIRE CONV E |
| Парткод: | 302H722690 |
| Деталь: | KEY START |
| Парткод: | 302LC05090 |
| Деталь: | KEY STOP |
| Парткод: | 302LC05100 |
| Деталь: | KEY RESET |
| Парткод: | 302LC05110 |
| Деталь: | KEY POWER |
| Парткод: | 302N405090 |
| Деталь: | LID OPERATION SHEET A |
| Парткод: | 302N405140 |
| Деталь: | LID OPERATION SHEET B |
| Парткод: | 302N405150 |
| Деталь: | PARTS TABLET OPERATION SP |
| Парткод: | 302N494100 |
| Деталь: | FILM FFC |
| Парткод: | 302LC05420 |
| Деталь: | KEY HOME |
| Парткод: | 302N405100 |
| Деталь: | KEY DISPLAY |
| Парткод: | 302N405110 |
| Деталь: | KEY RIGHT SIDE |
| Парткод: | 302N405120 |
| Деталь: | HOLDER LCD |
| Парткод: | 302LC05270 |
| Деталь: | SEAL FRAME SIDE B |
| Парткод: | 302H717440 |
| Деталь: | WIRE FFC KEY PWB |
| Парткод: | 302N446050 |
| Деталь: | LENS LED |
| Парткод: | 302N405200 |
| Деталь: | MOUNT MAIN PWB |
| Парткод: | 302N405020 |
| Деталь: | GUIDE WIRE OPERATION |
| Парткод: | 302N405160 |
| Деталь: | WIRE PANEL JOINT |
| Парткод: | 302N446030 |
| Деталь: | WIRE PANEL DATA |
| Парткод: | 302N446010 |
| Деталь: | WIRE MAIN-OPERATION |
| Парткод: | 302N446020 |
| Деталь: | PARTS SPEAKER SP |
| Парткод: | 302LC94370 |
| Деталь: | WIRE USB HOST |
| Парткод: | 302N446040 |
| Деталь: | SPRING USB HOLD |
| Парткод: | 302K905900 |
| Деталь: | COVER OPERATION B |
| Парткод: | 302N405190 |
| Деталь: | PANEL OPERATION |
| Парткод: | 302N905010 |
| Деталь: | SHEET OPERATION EN |
| Парткод: | 302N905510 |
| Деталь: | SHEET OPERATION KDA EN |
| Парткод: | 302N905630 |
| Деталь: | MOUNT SLIDE |
| Парткод: | 302GR05120 |
| Деталь: | BUSH SLIDE OPE |
| Парткод: | 302H005340 |
| Деталь: | PIN HINGE OPE C |
| Парткод: | 302H005690 |
| Деталь: | BUSH PIN OPE |
| Парткод: | 302H705350 |
| Деталь: | HANDLE OPERATION |
| Парткод: | 302LC05370 |
| Деталь: | SPRING CLEANING SOLENOID |
| Парткод: | 75018250 |
| Деталь: | SLIDER OPERATION-UNIT |
| Парткод: | 302LC05240 |
| Деталь: | BASE OPERATION-UNIT |
| Парткод: | 302LC05231 |
| Деталь: | MOUNT OPERATION-UNIT |
| Парткод: | 302LC05221 |
| Деталь: | PLATE EARTH ISU |
| Парткод: | 302K302A50 |
| Деталь: | COVER SLIDE |
| Парткод: | 302LC05301 |
| Деталь: | HOLDER WIRE A |
| Парткод: | 303LL02180 |
| Деталь: | HOLDER SPEAKER |
| Парткод: | 302N405180 |
| Деталь: | GUIDE WIRE OPERATION |
| Парткод: | 302LC05350 |
| Деталь: | WIRE PANEL-LVU |
| Парткод: | 302LC46770 |
| Деталь: | SHEET OPERATION KDA FR |
| Парткод: | 302N905640 |
| Деталь: | SHEET OPERATION KDA ES |
| Парткод: | 302N905650 |
| Деталь: | SHEET OPERATION KDA PT |
| Парткод: | 302N905660 |
| Деталь: | SHEET OPERATION DE |
| Парткод: | 302N905530 |
| Деталь: | SHEET OPERATION FR |
| Парткод: | 302N905540 |
| Деталь: | SHEET OPERATION TL |
| Парткод: | 302N905550 |
| Деталь: | SHEET OPERATION ES |
| Парткод: | 302N905560 |
| Деталь: | SHEET OPERATION PT |
| Парткод: | 302N905570 |
| Деталь: | SHEET OPERATION NL |
| Парткод: | 302N905580 |
| Деталь: | SHEET OPERATION RU |
| Парткод: | 302N905590 |
| Деталь: | PARTS OPERATION UNIT SP |
| Парткод: | 302N994010 |
| Деталь: | HOLDER FEED DRIVE |
| Парткод: | 302K931411 |
| Деталь: | SHAFT MID DRIVE |
| Парткод: | 302K931441 |
| Деталь: | COUPLING DRIVE |
| Парткод: | 302K931530 |
| Деталь: | SPRING DRUM JOINT |
| Парткод: | 302H712650 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | SHAFT FEED DRIVE |
| Парткод: | 302K931431 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | WIRE FEED CLUTCH |
| Парткод: | 302K946AB0 |
| Деталь: | GEAR Z28L |
| Парткод: | 302K931490 |
| Деталь: | PARTS CLUTCH 50 Z35R SP |
| Парткод: | 303M894090 |
| Деталь: | PIN FEED DRIVE |
| Парткод: | 302K931450 |
| Деталь: | GEAR Z28R |
| Парткод: | 302K931500 |
| Деталь: | GEAR Z27L |
| Парткод: | 302K931550 |
| Деталь: | GEAR Z27L MAIN |
| Парткод: | 302JZ31170 |
| Деталь: | GEAR Z35R |
| Парткод: | 302K931510 |
| Деталь: | GEAR Z40L-Z34L |
| Парткод: | 302K931520 |
| Деталь: | GEAR Z79R-Z34R |
| Парткод: | 302LC31410 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | PLATE FEED DRIVE |
| Парткод: | 302K931420 |
| Деталь: | PARTS MOTOR-BL W20 SP |
| Парткод: | 302K994320 |
| Деталь: | PLATE EARTH FEED |
| Парткод: | 302K931540 |
| Деталь: | PARTS PWB FEED 2 ASSY SP |
| Парткод: | 302N694040 |
| Деталь: | WIRE FEED MOTOR |
| Парткод: | 302LC46440 |
| Деталь: | WIRE FEED POWER |
| Парткод: | 302K946930 |
| Деталь: | GEAR Z35S |
| Парткод: | 302K903130 |
| Деталь: | HOLDER CONT DRIVE K |
| Парткод: | 302K931710 |
| Деталь: | PARTS LSU RETAINER MOTOR ASSY SP |
| Парткод: | 302K994140 |
| Деталь: | SEAL MOTOR DC |
| Парткод: | 302LC31511 |
| Деталь: | PLATE DC MOTOR 10 |
| Парткод: | 302K902610 |
| Деталь: | WORM WHEEL Z56L-Z20S |
| Парткод: | 302K931760 |
| Деталь: | SHAFT CONT DRIVE |
| Парткод: | 302K931780 |
| Деталь: | GEAR Z34S JOINT |
| Парткод: | 302K931830 |
| Деталь: | PLATE CONT DRIVE |
| Парткод: | 302K931720 |
| Деталь: | PARTS PWB RFID ASSY SP |
| Парткод: | 302K394070 |
| Деталь: | SPRING PADDLE CONT D |
| Парткод: | 302H731650 |
| Деталь: | COUPLING CONT D |
| Парткод: | 302H731640 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | WIRE CONTAINER MOTOR |
| Парткод: | 302LF46350 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | GEAR Z20S JOINT FEED B |
| Парткод: | 302H006120 |
| Деталь: | GEAR Z20S |
| Парткод: | 302LC03130 |
| Деталь: | GEAR Z30S COUPLING |
| Парткод: | 302LC03140 |
| Деталь: | GEAR Z18S |
| Парткод: | 302K903140 |
| Деталь: | MOUNT DRIVE |
| Парткод: | 302LC03160 |
| Деталь: | SPRING COUPLING |
| Парткод: | 302LC03200 |
| Деталь: | PLATE DRIVE |
| Парткод: | 302LC03170 |
| Деталь: | BUSHING 6,REGISTRATION |
| Парткод: | 2BC06520 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | SHAFT DRIVE C |
| Парткод: | 302LH03150 |
| Деталь: | PARTS FEED DRIVE L SP |
| Парткод: | 302L693080 |
| Деталь: | PARTS CONT DRIVE UNIT K SP |
| Парткод: | 302LF94080 |
| Деталь: | COVER TOP TRAY |
| Парткод: | 302N404020 |
| Цена: | 7 200 ₽ |
| Деталь: | COVER RIGHT LOWER F |
| Парткод: | 302LC04052 |
| Деталь: | COVER RIGHT MIDDLE R |
| Парткод: | 302LC04064 |
| Деталь: | COVER RIGHT LOWER R |
| Парткод: | 302LC04072 |
| Деталь: | COVER EXIT |
| Парткод: | 302N404070 |
| Деталь: | COVER TRAY REAR |
| Парткод: | 302N404080 |
| Деталь: | COVER ISU BOTTOM |
| Парткод: | 302N404090 |
| Деталь: | COVER INNER LEFT |
| Парткод: | 302LC04251 |
| Деталь: | COVER INNER FEED F |
| Парткод: | 302LC04260 |
| Деталь: | Cover Handle |
| Парткод: | 302LC04280 |
| Деталь: | COVER MAIN SWITCH |
| Парткод: | 302LC04290 |
| Деталь: | MOUNT FRONT COVER LEFT |
| Парткод: | 302LC04410 |
| Деталь: | STOPPER ORIGINAL |
| Парткод: | 302LC04720 |
| Деталь: | STRAP FRONT COVER |
| Парткод: | 302LC04651 |
| Деталь: | LABEL SW CAUTION EN |
| Парткод: | 302LC34050 |
| Деталь: | EMBLEM |
| Парткод: | 302LC04272 |
| Деталь: | SHEET EMBLEM 5501 |
| Парткод: | 302N904030 |
| Деталь: | SHEET EMBLEM 4501 |
| Парткод: | 302NA04010 |
| Деталь: | SHEET EMBLEM 3501 |
| Парткод: | 302NB04010 |
| Деталь: | PLATE MAGNET |
| Парткод: | 2FB04270 |
| Деталь: | SHEET COVER FRONT |
| Парткод: | 302LC04730 |
| Деталь: | COVER FRONT |
| Парткод: | 302N904020 |
| Деталь: | PARTS COVER FRONT SP |
| Парткод: | 302LC94520 |
| Деталь: | STOPPER CONTAINER |
| Парткод: | 302LC04460 |
| Деталь: | PLATE EARTH FRAME REAR |
| Парткод: | 302N402020 |
| Деталь: | WIRE FRONT LOW |
| Парткод: | 302LC46230 |
| Деталь: | PARTS,HUMIDITY SENSOR,SP |
| Парткод: | 302H094300 |
| Деталь: | COVER HUMIDITY SENSOR |
| Парткод: | 302LC02710 |
| Деталь: | SHEET HUMIDITY SENSOR A |
| Парткод: | 302LC02720 |
| Деталь: | SHEET HUMIDITY SENSOR B |
| Парткод: | 302LC02730 |
| Деталь: | SPONGE LOWER RIGHT |
| Парткод: | 302LF33870 |
| Деталь: | COVER FRONT RIGHT LOWER |
| Парткод: | 302LC04241 |
| Деталь: | SPACER USB |
| Парткод: | 302LW04260 |
| Деталь: | SHEET COVER FRONT B |
| Парткод: | 302LC04740 |
| Деталь: | LABEL SW CAUTION SET A |
| Парткод: | 302LC34160 |
| Деталь: | FK-6306 B |
| Парткод: | 302LH93100 |
| Деталь: | FK-6307 B |
| Парткод: | 302LH93110 |
| Деталь: | FRAME CONVEYING F |
| Парткод: | 302K929011 |
| Деталь: | SHAFT CONVEYING HOOK UP |
| Парткод: | 302K929100 |
| Деталь: | LEVER COVER RIGHT |
| Парткод: | 302K929090 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | PLATE CONVEYING TOP |
| Парткод: | 302K929051 |
| Деталь: | PLATE CONVEYING LOW |
| Парткод: | 302K929040 |
| Деталь: | FRAME CONVEYING R |
| Парткод: | 302K929020 |
| Деталь: | ARM HOOK F |
| Парткод: | 302K929400 |
| Деталь: | HOOK CONVEYING UP |
| Парткод: | 302K929120 |
| Деталь: | SPRING HOOK UP |
| Парткод: | 302K929190 |
| Деталь: | HOOK CONVEYING LOW F |
| Парткод: | 302K929140 |
| Деталь: | SPRING HOOK |
| Парткод: | 3HL07240 |
| Деталь: | CAM HOOK FRONT |
| Парткод: | 302K929170 |
| Деталь: | PIN CONVEYING F |
| Парткод: | 302K929630 |
| Деталь: | GUIDE UNIT F |
| Парткод: | 302LH29010 |
| Деталь: | GUIDE UNIT F |
| Парткод: | 302LL29010 |
| Деталь: | ARM HOOK R |
| Парткод: | 302K929410 |
| Деталь: | HOOK CONVEYING LOW R |
| Парткод: | 302K929150 |
| Деталь: | CAM HOOK REAR |
| Парткод: | 302K929160 |
| Деталь: | PLATE CONVEYING UP |
| Парткод: | 302K929030 |
| Деталь: | Cover arm |
| Парткод: | 302K929710 |
| Деталь: | GEAR Z30R-Z27L |
| Парткод: | 302K929240 |
| Деталь: | PLATE JOINT |
| Парткод: | 302K929600 |
| Деталь: | GUIDE GEAR |
| Парткод: | 302K929610 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | MOUNT DU DRIVE |
| Парткод: | 302K929062 |
| Деталь: | MOUNT DU DRIVE |
| Парткод: | 302LK29062 |
| Деталь: | SPRING LEVER EF |
| Парткод: | 302F902180 |
| Деталь: | GUIDE UNIT R |
| Парткод: | 302K929580 |
| Деталь: | PARTS PWB JUNCTION ASSY SP |
| Парткод: | 302K994201 |
| Деталь: | SPRING HOLDER PULLEY |
| Парткод: | 302K924770 |
| Деталь: | PULLEY MPT BYPASS |
| Парткод: | 302FZ07020 |
| Деталь: | PLATE EARTH DU |
| Парткод: | 302K929690 |
| Деталь: | PARTS ROLLER DU UP SP |
| Парткод: | 302K994491 |
| Деталь: | PARTS ROLLER DU UP SP |
| Парткод: | 302LK94070 |
| Деталь: | BUSH 8 |
| Парткод: | 28107310 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302HG12310 |
| Деталь: | GUIDE DU LOWER B |
| Парткод: | 302LC29022 |
| Деталь: | GEAR Z45L |
| Парткод: | 302LC31760 |
| Деталь: | MOUNT MOTOR DU UP |
| Парткод: | 302LC29110 |
| Деталь: | BUSH DU EW |
| Парткод: | 302K924830 |
| Деталь: | PARTS MOTOR PM REGIST SP |
| Парткод: | 302K994980 |
| Деталь: | COVER CLUTCH B |
| Парткод: | 302LC29070 |
| Деталь: | PARTS CLUTCH 50 Z35R SP |
| Парткод: | 303M894090 |
| Деталь: | GUIDE DU UPPER B |
| Парткод: | 302LC29012 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | ACTUATOR DU B |
| Парткод: | 302LC29051 |
| Деталь: | SPRING-TORSION SWITCHBACK |
| Парткод: | 302K928190 |
| Деталь: | PARTS,FAN COOLING CONVEYING SP |
| Парткод: | 302FZ94420 |
| Деталь: | SHEET GUIDE DU FAN |
| Парткод: | 302LH29030 |
| Деталь: | WIRE DU UPPER |
| Парткод: | 302K946240 |
| Деталь: | WIRE DU UPPER |
| Парткод: | 302LL46240 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | SHAFT FEED |
| Парткод: | 302K324460 |
| Деталь: | PULLEY DU LOW |
| Парткод: | 302F929260 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | SPRING-COMPRESSION |
| Парткод: | 302LC29100 |
| Деталь: | COVER RIGHT GUIDE |
| Парткод: | 302K929490 |
| Деталь: | COVER WIRE |
| Парткод: | 302K929750 |
| Деталь: | PIN CONVEYING R |
| Парткод: | 302K929640 |
| Деталь: | HOLDER DRAWER |
| Парткод: | 302K924390 |
| Деталь: | PLATE DRAWER |
| Парткод: | 302K929620 |
| Деталь: | WIRE CONVEYING |
| Парткод: | 302LF46520 |
| Деталь: | COVER INNER CONVEYING A |
| Парткод: | 302LF29030 |
| Деталь: | WIRE MPF JOINT |
| Парткод: | 302LC46480 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | PIN DRIVE B |
| Парткод: | 302HN31680 |
| Деталь: | GEAR Z23R-Z23L |
| Парткод: | 302K929550 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | WIRE CONVEYING MOTOR |
| Парткод: | 302LF46AL0 |
| Деталь: | SHEET DU GUIDE LOWER |
| Парткод: | 302LH29050 |
| Деталь: | GEAR Z23R PULLEY P18 S2M |
| Парткод: | 302K929280 |
| Деталь: | BELT S2M Z204 |
| Парткод: | 302K929320 |
| Деталь: | COLLAR DEVELOPING UNIT |
| Парткод: | 75714210 |
| Деталь: | GEAR Z27L |
| Парткод: | 302LK29030 |
| Деталь: | GEAR Z45L |
| Парткод: | 302K929250 |
| Деталь: | GEAR Z42R |
| Парткод: | 302K929260 |
| Деталь: | GEAR Z25L |
| Парткод: | 302K929270 |
| Деталь: | PARTS CONVEYING H UNIT(G) SP |
| Парткод: | 302LH94042 |
| Деталь: | PARTS CONVEYING L UNIT(G) SP |
| Парткод: | 302LL94012 |
| Деталь: | TRAY WASTE |
| Парткод: | 302LC03711 |
| Деталь: | PULLEY WASTE TRAY |
| Парткод: | 302LC03510 |
| Деталь: | LEVER WASTE TRAY |
| Парткод: | 302H703390 |
| Деталь: | HOLDER JOINT WASTE |
| Парткод: | 302LC03790 |
| Деталь: | BUSH BEVEL |
| Парткод: | 302LC03750 |
| Деталь: | SHAFT DRIVE D |
| Парткод: | 302LC03780 |
| Деталь: | GEAR BEVEL Z24 |
| Парткод: | 302LC03770 |
| Деталь: | TORQUE LIMITER 360 |
| Парткод: | 302GR06110 |
| Деталь: | GEAR Z18S COUPLING |
| Парткод: | 302LC03120 |
| Деталь: | PIN MOUNT DRIVE |
| Парткод: | 302LC03430 |
| Деталь: | GEAR Z25S |
| Парткод: | 302LC03100 |
| Деталь: | MOUNT WASTE DRIVE |
| Парткод: | 302LC03720 |
| Деталь: | GEAR JOINT Z30S |
| Парткод: | 302LC03210 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 2BG22990 |
| Деталь: | BUSH 4-7 |
| Парткод: | 302LC03230 |
| Деталь: | MOUNT TRAY DRIVE |
| Парткод: | 302LC03740 |
| Деталь: | GEAR BEVEL Z24 JOINT |
| Парткод: | 302LC03760 |
| Деталь: | SHEET WASTE TRAY |
| Парткод: | 302LC03311 |
| Деталь: | LABEL PUSH A |
| Парткод: | 302H734170 |
| Деталь: | SEAL WASTE TRAY |
| Парткод: | 302LC03A70 |
| Деталь: | FRAME WASTE TRAY |
| Парткод: | 302LH03061 |
| Деталь: | SPRING HOOK WASTE |
| Парткод: | 302H703450 |
| Деталь: | SHAFT HOOK |
| Парткод: | 302LC03680 |
| Деталь: | HOOK TRAY R |
| Парткод: | 302LC03660 |
| Деталь: | HOOK TRAY L |
| Парткод: | 302LC03670 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | RAIL WASTE R |
| Парткод: | 302LH03090 |
| Деталь: | RAIL WASTE L |
| Парткод: | 302LC03320 |
| Деталь: | HOLDER TONER SENSOR |
| Парткод: | 302LH03080 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1A173LCH01 |
| Деталь: | LEVER TONER SENSOR |
| Парткод: | 302LC03590 |
| Деталь: | WIRE RETAINER |
| Парткод: | 302LH46190 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | SPRING TRAY WASTE |
| Парткод: | 302H703510 |
| Деталь: | WT-860/WASTE TONER BOTTLE |
| Парткод: | 1902LC0UN0 |
| Деталь: | COVER INNER |
| Парткод: | 302N904010 |
| Деталь: | NUT FUSER A /FS-1800/3800 A4 |
| Парткод: | 5MMS111SL002 |
| Деталь: | COVER CONNECTOR |
| Парткод: | 302LC03500 |
| Деталь: | MAGNET CATCH |
| Парткод: | 302H004660 |
| Деталь: | WIRE RETAINER JOINT |
| Парткод: | 302LH46200 |
| Деталь: | LABEL TONER OPERATION |
| Парткод: | 302LH34020 |
| Деталь: | PARTS WASTE TRAY UNIT SP |
| Парткод: | 302LC94480 |
| Деталь: | PARTS WASTE BOTTLE CASE ASSY SP |
| Парткод: | 302LH94130 |
| Деталь: | LID KMAS |
| Парткод: | 2C912430 |
| Деталь: | LID DP BOARD |
| Парткод: | 302LC04770 |
| Деталь: | LABEL MPF CAUTION B |
| Парткод: | 302LC34070 |
| Деталь: | LABEL MPF PUSH |
| Парткод: | 302LC34110 |
| Деталь: | COVER RIGHT |
| Парткод: | 302K929201 |
| Деталь: | COVER RIGHT UPPER |
| Парткод: | 302LC04042 |
| Деталь: | COVER RIGHT MIDDLE |
| Парткод: | 302LC04081 |
| Деталь: | COVER REAR LOWER |
| Парткод: | 302N904040 |
| Деталь: | COVER REAR UPPER |
| Парткод: | 302N404390 |
| Деталь: | COVER INNER CONVEYING B |
| Парткод: | 302K929590 |
| Деталь: | LID FAX BOARD |
| Парткод: | 302LC04471 |
| Деталь: | LABEL MPF SET A |
| Парткод: | 302LC34180 |
| Деталь: | BUSHING,TRANSFER |
| Парткод: | 2A116180 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | DUCT WASTE B |
| Парткод: | 302LH03520 |
| Деталь: | PADDLE WASTE A |
| Парткод: | 302LH03240 |
| Деталь: | PADDLE WASTE B |
| Парткод: | 302LH03540 |
| Деталь: | SEAL SCREW |
| Парткод: | 302H703430 |
| Деталь: | SEAL PADDLE |
| Парткод: | 302LH03590 |
| Деталь: | DUCT WASTE A |
| Парткод: | 302LH03511 |
| Деталь: | GEAR Z23S |
| Парткод: | 302LH03550 |
| Деталь: | CUT WASHER 4 |
| Парткод: | 302FB09830 |
| Деталь: | SEAL SHUTTER WASTE |
| Парткод: | 302LC03080 |
| Деталь: | SPACER LED /43587J2063 A4 |
| Парткод: | 5MVS313SB002 |
| Деталь: | PARTS TONER FULL DETECT ASSY SP |
| Парткод: | 302K994150 |
| Деталь: | COVER SHUTTER |
| Парткод: | 302LC03570 |
| Деталь: | LID COVER SHUTTER |
| Парткод: | 302LC03460 |
| Деталь: | SPRING WASTE SHUTTER |
| Парткод: | 302LC03A80 |
| Деталь: | SHUTTER WASTE |
| Парткод: | 302LC03070 |
| Деталь: | PARTS CLN WT MOTOR ASSY SP |
| Парткод: | 302LC94180 |
| Деталь: | HOLDER DC MOTOR |
| Парткод: | 302LH03530 |
| Деталь: | WORM-WHEEL 36 Z18S |
| Парткод: | 302K908360 |
| Деталь: | GEAR Z21 IDLE |
| Парткод: | 302K914410 |
| Деталь: | GEAR Z44S-Z18S |
| Парткод: | 302LH03130 |
| Деталь: | GEAR Z40S |
| Парткод: | 302LH03120 |
| Деталь: | FILM WIRE B |
| Парткод: | 302LH03570 |
| Деталь: | WIRE MOTOR JOINT |
| Парткод: | 302LH46300 |
| Деталь: | SEAL DUCT CASS A |
| Парткод: | 302LH03960 |
| Деталь: | SEAL DUCT CASS B |
| Парткод: | 302LF03970 |
| Деталь: | SEAL DUCT DRUM C |
| Парткод: | 302LH03980 |
| Деталь: | PARTS INNER UNIT SP |
| Парткод: | 302LH94033 |
| Деталь: | PARTS INNER UNIT SP |
| Парткод: | 302NB94010 |
| Деталь: | MC-6705 |
| Парткод: | 302LF93021 |
| Деталь: | DV-6305 |
| Парткод: | 302LH93034 |
| Деталь: | SHUTTER PIPE UP |
| Парткод: | 302H703100 |
| Деталь: | SEAL PIPE DLP UP |
| Парткод: | 302H703130 |
| Деталь: | SPRING PIPE UP |
| Парткод: | 302H703240 |
| Деталь: | SEAL CONT SHUTTER |
| Парткод: | 302H703570 |
| Деталь: | SPRING SHUTTER |
| Парткод: | 302K914370 |
| Деталь: | SHUTTER HOPPER UP |
| Парткод: | 302K915240 |
| Деталь: | SEAL SHUTTER |
| Парткод: | 302K915320 |
| Деталь: | PIPE DLP UP |
| Парткод: | 302H703542 |
| Деталь: | BASE GUIDE CONTAINER |
| Парткод: | 302N903710 |
| Деталь: | RAIL CONTAINER L |
| Парткод: | 302LH03730 |
| Деталь: | SHAFT CAM |
| Парткод: | 302LF02220 |
| Деталь: | MOUNT CAM |
| Парткод: | 302LF02240 |
| Деталь: | CAM DLP PRESS |
| Парткод: | 302LF02230 |
| Деталь: | SPRING CAM |
| Парткод: | 302LF02250 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | BUSH 8 |
| Парткод: | 302H024830 |
| Деталь: | PLATE PRESS LEVER |
| Парткод: | 302LF02210 |
| Деталь: | LEVER DLP RAIL |
| Парткод: | 302LF02260 |
| Деталь: | SPRING LEVER DLP |
| Парткод: | 302LF02180 |
| Деталь: | ARM RAIL R |
| Парткод: | 302N702120 |
| Деталь: | SPRING HV |
| Парткод: | 302K939360 |
| Деталь: | SPRING HV |
| Парткод: | 302K939200 |
| Деталь: | TERMINAL MAG |
| Парткод: | 302LF02150 |
| Деталь: | TERMINAL SLEEVE |
| Парткод: | 302LF02160 |
| Деталь: | SHAFT DLP DRIVE |
| Парткод: | 302K931180 |
| Деталь: | SPRING COUPLING DLP |
| Парткод: | 302BG22531 |
| Деталь: | COUPLING DLP DRIVE |
| Парткод: | 302FZ31250 |
| Деталь: | COLLAR DLP COUPLING |
| Парткод: | 302FZ31280 |
| Деталь: | PIN CASSETTE RAIL |
| Парткод: | 2FB06710 |
| Деталь: | GEAR Z74R |
| Парткод: | 302K931190 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | RETAINER DLP DRIVE |
| Парткод: | 302LF02190 |
| Деталь: | PLATE EARTH DRIVE |
| Парткод: | 302LF02390 |
| Деталь: | SEAL TONER DUCT |
| Парткод: | 302N702050 |
| Деталь: | COVER TONER DUCT |
| Парткод: | 302N702130 |
| Деталь: | DUCT COOLING |
| Парткод: | 302LF02420 |
| Деталь: | SEAL COOLING DUCT |
| Парткод: | 302LF02430 |
| Деталь: | RAIL DLP |
| Парткод: | 302LF02100 |
| Деталь: | ARM RAIL F |
| Парткод: | 302LF02110 |
| Деталь: | WIRE DEVELOPER JOINT |
| Парткод: | 302LF46640 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | PULLEY,DRUM SEPARATION |
| Парткод: | 2A118370 |
| Цена: | 90 ₽ |
| Деталь: | COVER DRUM |
| Парткод: | 302LF02281 |
| Деталь: | STAY DRUM COVER |
| Парткод: | 302LF02350 |
| Деталь: | ARM COVER DRUM FRONT |
| Парткод: | 302LF02291 |
| Деталь: | MOUNT COVER DRUM FRONT |
| Парткод: | 302LF02370 |
| Деталь: | ARM COVER DRUM REAR |
| Парткод: | 302LF02301 |
| Деталь: | MOUNT COVER DRUM REAR |
| Парткод: | 302LF02360 |
| Деталь: | SPRING-TORSION ARM A FRONT |
| Парткод: | 302LF02310 |
| Деталь: | SPRING-TORSION ARM B FRONT |
| Парткод: | 302LF02330 |
| Деталь: | SPRING-TORSION ARM A REAR |
| Парткод: | 302LF02320 |
| Деталь: | SPRING-TORSION ARM B REAR |
| Парткод: | 302LF02340 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | DK-6306 |
| Парткод: | 302N993030 |
| Деталь: | PARTS IMAGE SCANNER L SP |
| Парткод: | 302N693020 |
| Деталь: | SENSOR ORIGINAL |
| Парткод: | 302H044110 |
| Деталь: | PARTS MOUNT LED ASSY SP |
| Парткод: | 302N493040 |
| Деталь: | PARTS CONTACT-GLASS ASSY(I) SP |
| Парткод: | 302K994030 |
| Деталь: | PARTS CONTACT-GLASS ASSY(C) SP |
| Парткод: | 302K994040 |
| Деталь: | PARTS PWB ISC ASSY SP |
| Парткод: | 302N494200 |
| Деталь: | WIRE FFC CCD |
| Парткод: | 302K946670 |
| Деталь: | WIRE FFC LED |
| Парткод: | 302K946710 |
| Деталь: | COVER ISU FRONT |
| Парткод: | 302N404190 |
| Деталь: | COVER ISU LEFT |
| Парткод: | 302LC04130 |
| Деталь: | COVER ISU RIGHT |
| Парткод: | 302LC04141 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | MOUNT LEFT PULLEY |
| Парткод: | 302KK17031 |
| Деталь: | PULLEY SCANNER |
| Парткод: | 302H717160 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | PLATE PULLEY |
| Парткод: | 302GR17860 |
| Деталь: | PULLEY LEFT FRAME |
| Парткод: | 302K917150 |
| Деталь: | PIN WIRE PULLEY B |
| Парткод: | 302GR17350 |
| Деталь: | GUIDE WIRE ISU |
| Парткод: | 302K917381 |
| Деталь: | MOUNT DP HINGE |
| Парткод: | 302N217010 |
| Деталь: | BEARING 688ZZ |
| Парткод: | 7BE008165431H01 |
| Деталь: | HOLDER BEARING 688ZZ |
| Парткод: | 302K931960 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | PULLEY ISU Z59 |
| Парткод: | 302K917021 |
| Деталь: | DRUM PULLEY |
| Парткод: | 302H717251 |
| Деталь: | WIRE SCANNER FRONT |
| Парткод: | 302H717381 |
| Деталь: | WIRE SCANNER REAR |
| Парткод: | 302H717391 |
| Деталь: | SHAFT ISU |
| Парткод: | 302K917060 |
| Деталь: | FRAME MIRROR B |
| Парткод: | 302K917091 |
| Деталь: | MIRROR B |
| Парткод: | 2FB1218 |
| Деталь: | MIRROR HOLDER |
| Парткод: | 75712080 |
| Деталь: | PULLEY SCANNER |
| Парткод: | 302H017180 |
| Деталь: | PLATE ADJUST B |
| Парткод: | 302K317830 |
| Деталь: | GUIDE FFC LED B |
| Парткод: | 302K317160 |
| Деталь: | SLIDER SCANNER |
| Парткод: | 2DC12230 |
| Деталь: | WIRE SCANNER MOTOR |
| Парткод: | 302N446240 |
| Деталь: | PLATE SLIT PI |
| Парткод: | 302K917080 |
| Деталь: | SPRING SCANNER TENSION |
| Парткод: | 302C912291 |
| Деталь: | FRAME MIRROR A |
| Парткод: | 302K317061 |
| Деталь: | MIRROR A |
| Парткод: | 302KK17320 |
| Деталь: | SPRING,MIRROR HOLDER |
| Парткод: | 2BC12190 |
| Деталь: | RETAINER WIRE |
| Парткод: | 2C912150 |
| Деталь: | GUIDE FFC LED C |
| Парткод: | 302K317172 |
| Деталь: | SHEET FFC LED |
| Парткод: | 302K317791 |
| Деталь: | GUIDE FFC LED D |
| Парткод: | 302K317310 |
| Деталь: | MOUNT RELEASE SWITCH |
| Парткод: | 302K917130 |
| Деталь: | SWITCH RELEASE |
| Парткод: | 302K917120 |
| Деталь: | SPRING RELEASE SWITCH |
| Парткод: | 302GR17380 |
| Деталь: | BELT ISU |
| Парткод: | 302K917040 |
| Деталь: | PARTS MOTOR ISU SP |
| Парткод: | 302N294010 |
| Деталь: | MOUNT ISU DRIVE |
| Парткод: | 302K917030 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | WIRE CCD POWER |
| Парткод: | 302K946680 |
| Деталь: | WIRE ORIGINAL SENSOR |
| Парткод: | 302K946750 |
| Деталь: | FERRITE CORE |
| Парткод: | 7YBFZZ65C001H01 |
| Деталь: | MOUNT PWB |
| Парткод: | 302K917230 |
| Деталь: | LK-6708 |
| Парткод: | 302N993010 |
| Деталь: | GUIDE WIRE FRONT PWB |
| Парткод: | 302LF39050 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | WIRE OPEN SENSOR |
| Парткод: | 302K946730 |
| Деталь: | WIRE HP SENSOR |
| Парткод: | 302K946A90 |
| Деталь: | MOUNT PI |
| Парткод: | 302K317330 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | COVER ISU |
| Парткод: | 302K917400 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZGSSTG58014H01 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZG65TSV+010H01 |
| Деталь: | SEAL FRAME SIDE B |
| Парткод: | 302H717440 |
| Деталь: | FILM FRAME |
| Парткод: | 302K317660 |
| Деталь: | SEAL FRAME ISU C |
| Парткод: | 302K317650 |
| Деталь: | SEAL FRAME ISU A |
| Парткод: | 302K317450 |
| Деталь: | SEAL FRAME ISU B |
| Парткод: | 302K317460 |
| Деталь: | WIRE CCD DATA |
| Парткод: | 302K946700 |
| Деталь: | WIRE ISC-MAIN |
| Парткод: | 302K946720 |
| Деталь: | FILM FRAME SIDE F |
| Парткод: | 302K917170 |
| Деталь: | FILM FRAME SIDE R |
| Парткод: | 302K917180 |
| Деталь: | CAP PULLEY ISU |
| Парткод: | 302K917240 |
| Деталь: | PIN SCANNER RETAINING |
| Парткод: | 302GR17180 |
| Деталь: | Control-panel assembly (Western) |
| Парткод: | 302N994011 |
| Цена: | 32 400 ₽ |
| Деталь: | Formatter, exchange, HP Color LaserJet 3000dn and 3000dtn Series only (256 MB) |
| Парткод: | 302N994041 |
| Цена: | 56 700 ₽ |
| Деталь: | Печь, в сборе (220В) |
| Парткод: | FK-6307B |
| Цена: | 22 800 ₽ |
| Деталь: | SPRING HV |
| Парткод: | 302K939360 |
| Деталь: | TERMINAL HV SEPARATION |
| Парткод: | 302LF39010 |
| Деталь: | PARTS MOUNT LED UNIT SP |
| Парткод: | 302LF94140 |
| Деталь: | COVER PWB IH |
| Парткод: | 302K939450 |
| Деталь: | SHIELD PWB |
| Парткод: | 302N939010 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | PARTS PWB HEATER 100 ASSY SP |
| Парткод: | 302N994060 |
| Деталь: | PARTS PWB HEATER 200 ASSY SP |
| Парткод: | 302N994070 |
| Деталь: | PARTS MOTOR LIFT ASSY SP |
| Парткод: | 302K394190 |
| Цена: | 6 000 ₽ |
| Деталь: | PARTS PWB FRONT MONO ASSY SP |
| Парткод: | 302LH94260 |
| Деталь: | PARTS PWB LSU JUNC MONO ASSY SP |
| Парткод: | 302N994080 |
| Деталь: | WIRE FFC LSU |
| Парткод: | 302N946020 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210003++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | TERMINAL HV DRUM |
| Парткод: | 302LF39020 |
| Деталь: | SPRING HV DRUM |
| Парткод: | 302LF39080 |
| Деталь: | PARTS HUMIDITY ASSY (G) SP |
| Парткод: | 302LH94120 |
| Деталь: | WIRE HEATER JOINT |
| Парткод: | 302LH46120 |
| Деталь: | WIRE HEATER PWB |
| Парткод: | 302N946010 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | GUIDE WIRE ISU |
| Парткод: | 302K939550 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | GUIDE WIRE INLET |
| Парткод: | 302K939381 |
| Деталь: | PLATE INLET B2 |
| Парткод: | 302N439070 |
| Деталь: | WIRE INLET ASSY 1 |
| Парткод: | 302N446270 |
| Деталь: | WIRE HVU TC |
| Парткод: | 302LF46320 |
| Деталь: | WIRE HVU MC |
| Парткод: | 302LF46340 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210004++H01 |
| Деталь: | Holder FFC |
| Парткод: | 302LF02380 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610017++H01 |
| Деталь: | GUIDE WIRE FRONT PWB |
| Парткод: | 302LF39050 |
| Деталь: | HOLDER PWB |
| Парткод: | 302K939230 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510007++H01 |
| Деталь: | WIRE FRONT POWER |
| Парткод: | 302LF46940 |
| Деталь: | PLATE MAIN SW |
| Парткод: | 302N439050 |
| Деталь: | WIRE FUSER JOINT |
| Парткод: | 302LH46591 |
| Деталь: | WIRE JOBSEPARATOR JOINT |
| Парткод: | 302LC46580 |
| Деталь: | WIRE HVU MAIN |
| Парткод: | 302N946060 |
| Деталь: | WIRE HVU MAIN |
| Парткод: | 302NB46020 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | SW.SEESAW |
| Парткод: | 7SC020403+++H01 |
| Деталь: | WIRE INTERLOCK |
| Парткод: | 302N946040 |
| Деталь: | WIRE MAIN SWITCH |
| Парткод: | 302N946030 |
| Деталь: | ACCESS.BUSHING |
| Парткод: | 7YZM110001++H01 |
| Деталь: | WIRE CONTAINER JOINT |
| Парткод: | 302LF46630 |
| Деталь: | WIRE EXIT FAN |
| Парткод: | 302N946050 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | GUIDE WIRE FUSER |
| Парткод: | 302LH39011 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | WIRE LIFT MOTOR |
| Парткод: | 302K946410 |
| Деталь: | COVER WIRE FUSER |
| Парткод: | 302K939521 |
| Деталь: | MOUNT PAPER LEVEL SENSOR |
| Парткод: | 302K909510 |
| Деталь: | PARTS SENSOR OPT SP |
| Парткод: | 303M894260 |
| Деталь: | WIRE PAPER SENSOR |
| Парткод: | 302K946420 |
| Деталь: | MOUNT SIZE SENSOR |
| Парткод: | 302K909520 |
| Деталь: | HOLDER SIZE DETECTION |
| Парткод: | 302K909541 |
| Деталь: | PIN PAPER SIZE A |
| Парткод: | 302K909580 |
| Деталь: | PIN PAPER SIZE B |
| Парткод: | 302K909590 |
| Деталь: | PIN PAPER SIZE C |
| Парткод: | 302K909600 |
| Деталь: | WIRE CASSETTE SIZE |
| Парткод: | 302K946400 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000006+H01 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP03072001+H01 |
| Деталь: | POWER CORD(120) |
| Парткод: | 3019527401 |
| Деталь: | POWER CORD(230) |
| Парткод: | 2AR27800 |
| Деталь: | AC CORD ASSY AS |
| Парткод: | 7AAACCAS+10H001 |
| Деталь: | PARTS PAPER LEVEL SENSOR ASSY SP |
| Парткод: | 302K994C80 |
| Деталь: | PARTS SIZE DETECTION ASSY SP |
| Парткод: | 302K994120 |
| Деталь: | PLATE CONTACT HV |
| Парткод: | 302K924290 |
| Деталь: | CAP PRESS TRANSFER |
| Парткод: | 302LF24010 |
| Деталь: | SPRING-COMPRESSION BELT ASSY B |
| Парткод: | 302LF24030 |
| Деталь: | SPRING-COMPRESSION BELT ASSY A |
| Парткод: | 302LF24020 |
| Деталь: | PLATE EARTH REGIST |
| Парткод: | 302K924250 |
| Деталь: | SHEET WIRE SENSOR |
| Парткод: | 302LF24160 |
| Деталь: | WIRE DU LOW |
| Парткод: | 302LF46310 |
| Деталь: | RETAINER LOOP SENSOR |
| Парткод: | 302K924100 |
| Деталь: | PARTS SENSOR OPT. SP |
| Парткод: | 302LC94410 |
| Деталь: | BUSH REGIST |
| Парткод: | 302K924901 |
| Деталь: | SPRING-COMPRESSION REGIST F |
| Парткод: | 302K924040 |
| Деталь: | SPRING-COMPRESSION REGIST R |
| Парткод: | 302K924050 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | BEARING MR106ZZ |
| Парткод: | 7BE006103431H01 |
| Деталь: | GEAR Z22R |
| Парткод: | 302K924060 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | SPRING EARTH CONVEYING |
| Парткод: | 302LF22600 |
| Деталь: | UNDER CLEANER REGIST |
| Парткод: | 2BL07950 |
| Цена: | 1 500 ₽ |
| Деталь: | ROLLER REGIST R |
| Парткод: | 302LF24150 |
| Деталь: | SHEET REGIST R |
| Парткод: | 302LF24190 |
| Деталь: | SPRING HOLDER PULLEY |
| Парткод: | 302K924770 |
| Деталь: | PULLEY MPT BYPASS |
| Парткод: | 302FZ07020 |
| Деталь: | PLATE EARTH RELEASE |
| Парткод: | 302K924810 |
| Деталь: | PARTS SOLENOID ID SENSOR SP |
| Парткод: | 302K994390 |
| Деталь: | MOUNT ID SENSOR |
| Парткод: | 302LF22390 |
| Деталь: | PARTS ID SENSOR ASSY SP |
| Парткод: | 302K994160 |
| Деталь: | MOUNT SENSOR UNIT |
| Парткод: | 302LF22540 |
| Деталь: | SHUTTER ID SENSOR |
| Парткод: | 302LF22550 |
| Деталь: | FELT CLEANER ID |
| Парткод: | 302HN02970 |
| Деталь: | ARM SOLENOID |
| Парткод: | 302LF22530 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | SPRING EXTENSION SHUTTER |
| Парткод: | 302LF22610 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210006++H01 |
| Деталь: | GEAR Z45L |
| Парткод: | 302LC31760 |
| Деталь: | BUSH DU EW |
| Парткод: | 302K924830 |
| Деталь: | PARTS MOTOR PM REGIST SP |
| Парткод: | 302K994980 |
| Деталь: | PARTS CLUTCH 50 Z35R SP |
| Парткод: | 303M894090 |
| Деталь: | PARTS ROLLER DU MID SP |
| Парткод: | 302K994480 |
| Деталь: | PLATE EARTH DU MIDDLE |
| Парткод: | 302K929660 |
| Деталь: | BELT S2M A145 |
| Парткод: | 302K929310 |
| Деталь: | MOUNT MOTOR DU MIDDLE |
| Парткод: | 302K929720 |
| Деталь: | LOCK COVER R /40283V0068 A4 |
| Парткод: | 5MVX421DN003 |
| Деталь: | POLYSLIDER CUT WASHER 4 |
| Парткод: | 302FZ21720 |
| Деталь: | SPRING-COMPRESSION COVER DU |
| Парткод: | 302K929680 |
| Деталь: | SPRING ACT DU |
| Парткод: | 302H729120 |
| Деталь: | ACTUATOR DU |
| Парткод: | 302K929330 |
| Деталь: | MOUNT PI |
| Парткод: | 302K924841 |
| Деталь: | SWITCH,COVER OPEN |
| Парткод: | 66127010 |
| Деталь: | WIRE DU SENSOR |
| Парткод: | 302K946460 |
| Деталь: | WIRE DU SENSOR |
| Парткод: | 302LK46460 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | FRAME DU |
| Парткод: | 302K924410 |
| Деталь: | SPRING DU |
| Парткод: | 302F925780 |
| Деталь: | PULLEY MIDDLE A |
| Парткод: | 302H722760 |
| Деталь: | PARTS ROLLER DU LOW SP |
| Парткод: | 302K994470 |
| Деталь: | PARTS ROLLER DU LOW SP |
| Парткод: | 302LK94060 |
| Деталь: | PLATE EARTH DU2 |
| Парткод: | 302K924920 |
| Деталь: | PULLEY 26 DU |
| Парткод: | 302H029110 |
| Деталь: | CUT-WASHER 6 |
| Парткод: | 302K921420 |
| Деталь: | BUSH 8 |
| Парткод: | 28107310 |
| Деталь: | SENSOR 248NL1 |
| Парткод: | 2C927210 |
| Деталь: | SHAFT FEED |
| Парткод: | 302K324460 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | 2FM04150 |
| Деталь: | SPRING DU |
| Парткод: | 302K929770 |
| Деталь: | BASE CONVEYING |
| Парткод: | 302K924011 |
| Деталь: | HOLDER CONTACT BELT |
| Парткод: | 302LF24091 |
| Деталь: | SPRING CONTACT BELT UNIT |
| Парткод: | 302LF24060 |
| Деталь: | PLATE CONTACT TRANSFER |
| Парткод: | 302LF24070 |
| Деталь: | PLATE CONTACT CLEANING |
| Парткод: | 302LF24081 |
| Деталь: | SPRING CONTACT TRANSFER |
| Парткод: | 302LF24040 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZG65TSV+020H01 |
| Деталь: | PARTS CONVEYING H UNIT(G) SP |
| Парткод: | 302LH94042 |
| Деталь: | PARTS CONVEYING L UNIT(G) SP |
| Парткод: | 302LL94012 |
| Деталь: | PARTS ID SENSOR ASSY SP |
| Парткод: | 302LF94070 |
| Деталь: | SHIELD BOX |
| Парткод: | 302N439010 |
| Деталь: | RAIL PWB |
| Парткод: | 302K939030 |
| Деталь: | BRACKET MAIN |
| Парткод: | 302N439030 |
| Деталь: | FILM REAR STAY |
| Парткод: | 302LH02080 |
| Деталь: | PARTS PWB KUIO ASSY SP |
| Парткод: | 302K994270 |
| Деталь: | WIRE FFC KUIO |
| Парткод: | 302N446090 |
| Деталь: | WIRE KUIO POWER |
| Парткод: | 302K946910 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390011++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302N994030 |
| Деталь: | PARTS PWB MAIN ASSY SP EU |
| Парткод: | 302N994040 |
| Деталь: | PARTS STORAGE DEVICE SP |
| Парткод: | 302LH93070 |
| Деталь: | WIRE HDD POWER |
| Парткод: | 302K946A10 |
| Деталь: | WIRE HDD DATA1 |
| Парткод: | 302N446130 |
| Деталь: | BRACKET HDD |
| Парткод: | 302N439020 |
| Деталь: | HOLDER FAN MAIN |
| Парткод: | 302K939043 |
| Деталь: | FAN BOX COOLING |
| Парткод: | 302FZ44040 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210005++H01 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210002++H01 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210003++H01 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510019++H01 |
| Деталь: | FILM SHIELD BOX |
| Парткод: | 302N439060 |
| Деталь: | CLAMP, LCT-1.5SIEM(TAKEUCHI) |
| Парткод: | M70AF010 |
| Деталь: | WIRE KEY COUNTER |
| Парткод: | 302K946AJ0 |
| Деталь: | PARTS MEMORY MODULE SP |
| Парткод: | 302LH94230 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | PLATE OPTION |
| Парткод: | 302K339050 |
| Деталь: | SCREW OP / M3 X 8 CRFREE A4 |
| Парткод: | 5MMT263SN012++R |
| Деталь: | BUSHING FAN |
| Парткод: | 302JD19140 |
| Деталь: | PIN HDD |
| Парткод: | 302MV39340 |
| Деталь: | PARTS PWB ENGINE ASSY SP |
| Парткод: | 302N994050 |
| Деталь: | PARTS UNIT HIGH VOLTAGE MAIN SP |
| Парткод: | 302LF94260 |
| Деталь: | PARTS UNIT HIGH VOLTAGE MAIN SP |
| Парткод: | 302LJ94010 |
| Цена: | 8 100 ₽ |
| Деталь: | WIRE FFC FEED1 |
| Парткод: | 302N446170 |
| Деталь: | WIRE FFC FEED2 |
| Парткод: | 302N446180 |
| Деталь: | WIRE FFC FEED3 |
| Парткод: | 302N446190 |
| Деталь: | PARTS PWB FEED 1 ASSY SP |
| Парткод: | 302N494160 |
| Деталь: | PARTS PWB FEED 1 ASSY SP |
| Парткод: | 302N694030 |
| Деталь: | WIRE FFC MAIN-ENGINE |
| Парткод: | 302N446100 |
| Деталь: | PARTS UNIT LOW VOLTAGE SP |
| Парткод: | 302N494080 |
| Деталь: | PLATE PWB LVU |
| Парткод: | 302K939401 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510007++H01 |
| Деталь: | WIRE CASSETTE HEATER LOOP |
| Парткод: | 302K946AR0 |
| Деталь: | PLATE OPTION COIN-VENDOR |
| Парткод: | 302K939430 |
| Деталь: | WIRE PF JOINT |
| Парткод: | 302LF46A70 |
| Деталь: | WIRE PF CASSETTE HEATER |
| Парткод: | 302K946A60 |
| Деталь: | LID VENDOR |
| Парткод: | 302FB26290 |
| Деталь: | WIRE MAIN-LVU |
| Парткод: | 302N446070 |
| Деталь: | WIRE LVU RIGHT |
| Парткод: | 302N446110 |
| Деталь: | GUIDE FFC FEED 1 |
| Парткод: | 302K939140 |
| Деталь: | PLATE PWB FEED |
| Парткод: | 302K939150 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610004++H01 |
| Деталь: | WIRE FEED JOINT |
| Парткод: | 302K946571 |
| Деталь: | WIRE FEED JOINT |
| Парткод: | 302LK46571 |
| Деталь: | PLATE COVER CONNECTOR |
| Парткод: | 302LC39030 |
| Деталь: | CLAMP,LCT-1.5SIEM(TAKEUCHI) |
| Парткод: | M70AF010 |
| Деталь: | MOUNT DRAWER A |
| Парткод: | 302K924340 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC60M2199+H01 |
| Деталь: | PIN DRAWER |
| Парткод: | 302K924350 |
| Деталь: | WIRE DU JOINT |
| Парткод: | 302LF46610 |
| Деталь: | MOUNT DRAWER B |
| Парткод: | 302K924380 |
| Деталь: | SPRING DRAWER |
| Парткод: | 302K924360 |
| Деталь: | SHEET COVER FUSER PWB |
| Парткод: | 302LC02780 |
| Деталь: | SHEET PWB HVU MAIN |
| Парткод: | 302LF02410 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610008++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | SHEET WIRE HVU MAIN |
| Парткод: | 302LF39090 |
| Деталь: | FILM WIRE ENGINE |
| Парткод: | 302LF39070 |
| Деталь: | HOLDER ATTACHMENT |
| Парткод: | 302K931210 |
| Деталь: | WIRE HVU DLP |
| Парткод: | 302LH46330 |
| Деталь: | WIRE T1 POWER |
| Парткод: | 302LF46950 |
| Деталь: | WIRE BRIDGE JOINT |
| Парткод: | 302N446290 |
| Деталь: | WIRE CASSETTE HEATER |
| Парткод: | 302LF46890 |
| Деталь: | GUIDE FFC FEED 2 |
| Парткод: | 302K939170 |
| Деталь: | HOLDER WIRE A |
| Парткод: | 303LL02180 |
| Деталь: | WIRE ENGINE POWER |
| Парткод: | 302K946960 |
| Деталь: | PARTS MOTOR-BL W10 SP |
| Парткод: | 302LC94291 |
| Деталь: | PLATE TRANSFER DRIVE |
| Парткод: | 302LF22120 |
| Деталь: | STAY TRANSFER |
| Парткод: | 302LF22220 |
| Деталь: | FRAME TRANSFER |
| Парткод: | 302LF22091 |
| Деталь: | Plate Bias |
| Парткод: | 302LF22310 |
| Деталь: | SHEET CONTACT HV |
| Парткод: | 302LF22620 |
| Деталь: | SPRING TRANSFER |
| Парткод: | 302LF22280 |
| Деталь: | ROLLER TRANSFER |
| Парткод: | 302LF22010 |
| Деталь: | PLATE HOLDER REAR |
| Парткод: | 302LF22290 |
| Деталь: | ROLLER TRANSFER DRIVE |
| Парткод: | 302LF22020 |
| Деталь: | BELT TRANSFER |
| Парткод: | 302LF22060 |
| Деталь: | ROLLER TRANSFER IDLE |
| Парткод: | 302LF22030 |
| Деталь: | PLATE HOLDER FRONT |
| Парткод: | 302LF22320 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | GEAR Z30R |
| Парткод: | 302LF22100 |
| Деталь: | BEARING MR106ZZ |
| Парткод: | 7BE006103431H01 |
| Деталь: | CUT-WASHER 4 |
| Парткод: | 302K924820 |
| Цена: | 160 ₽ |
| Деталь: | VARISTOR TC ASSY |
| Парткод: | 302FZ01310 |
| Деталь: | GEAR Z31R-Z42R |
| Парткод: | 302LF22210 |
| Деталь: | GEAR Z21L-Z39L |
| Парткод: | 302LF22110 |
| Деталь: | GUIDE TRANSFER FRONT B |
| Парткод: | 302LF22080 |
| Деталь: | SPRING TRANS GUIDE |
| Парткод: | 302LF22570 |
| Деталь: | COVER MOTOR |
| Парткод: | 302LF22200 |
| Деталь: | BUSH TRANSFER |
| Парткод: | 302LF22400 |
| Деталь: | COVER TRANSFER |
| Парткод: | 302LF22470 |
| Деталь: | GUIDE TRANSFER REAR |
| Парткод: | 302LF22230 |
| Деталь: | FILM GUIDE REAR |
| Парткод: | 302LF22260 |
| Деталь: | HOLDER TRANSFER REAR |
| Парткод: | 302LF22240 |
| Деталь: | STATIC-ELIMINATOR TRANSFER |
| Парткод: | 302LF22250 |
| Деталь: | SPACER PRESS TRANSFER |
| Парткод: | 302LF22380 |
| Деталь: | HOLDER TRANSFER FRONT |
| Парткод: | 302LF22140 |
| Деталь: | HOLDER TRANSFER REAR |
| Парткод: | 302LF22150 |
| Деталь: | RETAINER TRANSFER FRONT |
| Парткод: | 302LF22450 |
| Деталь: | RETAINER TRANSFER REAR |
| Парткод: | 302LF22460 |
| Деталь: | PARTS CONVEYING H UNIT(G) SP |
| Парткод: | 302LH94042 |
| Деталь: | PARTS CONVEYING L UNIT(G) SP |
| Парткод: | 302LL94012 |
| Деталь: | PARTS BELT ASSY SP |
| Парткод: | 302LF94060 |
| Деталь: | PARTS FAN COOLING DLP 70 SP |
| Парткод: | 302K994350 |
| Деталь: | FAN LSU 60-25 |
| Парткод: | 302GR44080 |
| Цена: | 2 800 ₽ |
| Деталь: | SEAL DUCT EXIT |
| Парткод: | 302K933580 |
| Деталь: | DUCT EXIT RIGHT |
| Парткод: | 302K933151 |
| Деталь: | FILM FUSER DUCT |
| Парткод: | 302LC33510 |
| Деталь: | DUCT EXIT LEFT |
| Парткод: | 302K933161 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610001++H01 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | FAN MOTOR |
| Парткод: | 302HN44010 |
| Деталь: | HOLDER FAN LOW VOLT |
| Парткод: | 302K933281 |
| Деталь: | WIRE LVU FAN |
| Парткод: | 302K946640 |
| Деталь: | SHEET GUIDE WIRE FRONT |
| Парткод: | 302LH33050 |
| Деталь: | DUCT FUSER LOW |
| Парткод: | 302LC33471 |
| Деталь: | SEAL FRAME MIDDLE A |
| Парткод: | 302HG02450 |
| Деталь: | DUCT FUSER REAR |
| Парткод: | 302K933190 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610002++H01 |
| Деталь: | DUCT FUSER RIGHT |
| Парткод: | 302K933560 |
| Деталь: | DUCT FUSER LEFT |
| Парткод: | 302K933572 |
| Деталь: | DUCT LSU LOW |
| Парткод: | 302LF33050 |
| Деталь: | DUCT LSU UP |
| Парткод: | 302LF33060 |
| Деталь: | SEAL DUCT LSU |
| Парткод: | 302LF33090 |
| Деталь: | WIRE LSU COOLING FAN |
| Парткод: | 302LH46171 |
| Деталь: | WIRE STOPPER |
| Парткод: | 302K931080 |
| Деталь: | PARTS,FAN IMAGE SP |
| Парткод: | 302FZ94660 |
| Деталь: | SPRING DUCT |
| Парткод: | 302LF02441 |
| Деталь: | TUBE DUCT |
| Парткод: | 302LF02450 |
| Деталь: | STOPPER TUBE |
| Парткод: | 302LF02460 |
| Деталь: | PARTS,FAN COOLING CONVEYING SP |
| Парткод: | 302FZ94420 |
| Деталь: | DUCT FAN BELT LEFT |
| Парткод: | 302LC33020 |
| Деталь: | SHEET FAN BELT |
| Парткод: | 302LC33210 |
| Деталь: | DUCT FAN BELT RIGHT |
| Парткод: | 302LC33010 |
| Деталь: | PARTS LID TONER FAN ASSY(ZG) SP |
| Парткод: | 302LF94410 |
| Деталь: | DUCT TONER LOW |
| Парткод: | 302LF33020 |
| Деталь: | DUCT TONER UP |
| Парткод: | 302LF33030 |
| Деталь: | SEAL TONER DUCT B |
| Парткод: | 302LF33210 |
| Деталь: | SEAL TONER DUCT C |
| Парткод: | 302LF33220 |
| Деталь: | SEAL DISPOSAL C |
| Парткод: | 302LF33290 |
| Деталь: | MOUNT TONER FAN |
| Парткод: | 302LF33360 |
| Деталь: | DUCT TONER SIDE |
| Парткод: | 302N733020 |
| Деталь: | DUCT LSU FRONT LEFT A |
| Парткод: | 302LF33131 |
| Деталь: | DUCT LSU FRONT LEFT B |
| Парткод: | 302LF33141 |
| Деталь: | SPONGE DUCT LSU LEFT |
| Парткод: | 302LF33460 |
| Деталь: | DUCT LSU SIDE |
| Парткод: | 302LF33150 |
| Деталь: | DUCT LSU REAR LEFT A |
| Парткод: | 302LF33110 |
| Деталь: | DUCT LSU REAR LEFT B |
| Парткод: | 302LF33120 |
| Деталь: | FAN COOLING DLP 70 |
| Парткод: | 302FZ44020 |
| Деталь: | WIRE COOLING FAN |
| Парткод: | 302LF46151 |
| Деталь: | PARTS DISPOSAL TONER UNIT SP |
| Парткод: | 302N794020 |
| Деталь: | FILTER LEFT SIDE |
| Парткод: | 302LC33370 |
| Цена: | 3 900 ₽ |
| Деталь: | PARTS FAN FUSER FRONT UNIT SP |
| Парткод: | 302K994090 |
| Деталь: | PARTS FILTER TONER UNIT(Z/G) SP |
| Парткод: | 302N794010 |
Коды ошибок
0030
0060
0070
0100
0120
0150
0160
0170
0180
0350
0620
0630
0640
0650
0660
0670
0800
0830
0840
0870
0920
0980
1000
1010
1020
1030
1040
1100
1110
1140
1400
1410
1710
1800
1900
2101
2201
2211
2300
2500
2550
2600
2810
3100
3210
3220
3300
3310
3500
3600
3700
3800
3900
4001
4011
4101
4201
5101
6000
6020
6030
6040
6050
6200
6220
6230
6250
6320
6400
6610
6910
7001
7101
7200
7210
7221
7231
7241
7251
7301
7401
7460
7601
7602
7800
7901
7911
7941
8010
8020
8030
8090
8100
8110
8120
8130
8140
8150
8160
8170
8180
8190
8200
8210
8230
8240
8250
8300
8310
8320
8330
8340
8350
8360
8370
8410
8420
8430
8500
8510
8520
8800
8900
8930
9000
9010
9040
9050
9060
9070
9080
9100
9110
9120
9130
9140
9150
9160
9170
9500
9510
9520
9940
9950
F000
F010
F040
F041
F050
F051
F278
Описание
| Error code: | 0030 |
| Description: | FAX control PWB system error Processing with the fax software was disabled due to a software problem. |
| Causes: | Defective FAX control PWB. |
| Remedy: | FAX control PWB 1. Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on. 2. Reinstall the fax software. 3. Replace the FAX control PWB. |
| Error code: | 0060 |
| Display: | FUSER MOTOR |
| Description: | Engine PWB mismatch Unmatching engine and engine sub boards. Defective engine subboard |
| Causes: | Defective engine sub PWB. |
| Remedy: | Engine PWB 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Replace the engine PWB. |
| Error code: | 0070 |
| Description: | FAX control PWB incompatible detection error Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
| Causes: | Defective FAX software. Defective FAX control PWB. |
| Remedy: | FAX control PWB (The FAX PWB installed will not be the one designed for the machine.) 1. Install the FAX system designed for the model. 2. Reinstall the fax software. |
| Error code: | 0100 |
| Display: | MAINTENANCE CALL 0100 |
| Description: | Backup memory device error |
| Causes: | Defective flash memory. Defective main PWB. |
| Remedy: | EEPROM (main PWB) 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the EEPROM on the main circuit PWB is peroperly installed on the main circuit PWB and, if not, re-install it. 3. Replace the main PWB |
| Error code: | 0120 |
| Description: | There is a problem with Thermistor for Pre-Heater. |
| Causes: | Thermistor Cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0150 |
| Description: | Even though the machine carries out the regular movement, the output of Slider Sensor does not reach the expected value. |
| Causes: | Slider Motor has a problem. Slider Sensor has a problem. Wiring or Flexible Cable has short circuitted or cut-line. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Slider Motor replacement Slider Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0160 |
| Description: | Even though the machine carries out the regular movement, the output of Pressure Pump 1 Sensor does not reach the expected value. |
| Causes: | Pressure Pump 1 Motor has a problem. Pressure Pump 1 Sensor has a problem. Pressure Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Pressure Pump 1 Magnet Pressure Pump 1 Motor replacement Pressure Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0170 |
| Description: | Even though the machine carries out the regular movement, the output of Supply Pump 1 Sensor does not reach the expected value. |
| Causes: | Supply Pump 1 Motor has a problem. Supply Pump 1 Sensor has a problem. Supply Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Supply Pump 1 Magnet Supply Pump 1 Motor replacement Supply Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0180 |
| Description: | Even though the machine carries out the regular movement, the output of Maintenance Liquid Pump Sensor does not reach the expected value. |
| Causes: | Maintenance Liquid Pump Motor has a problem. Maintenance Liquid Pump Sensor has a problem. Maintenance Liquid Pump Magnet has dropped out. Wiring or Flexible Cable has short circuitted |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Maintenance Liquid Pump Motor replacement Maintenance Liquid Pump Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0350 |
| Description: | Panel PWB communication error (electronic volume I2C communication error) NACK is received during I2C communication -> retried 5 times -> rebooting command sent -> retried 5 times If NACK is still received. |
| Causes: | Operation PWB. Main PWB |
| Remedy: | Operation PWB 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Operation PWB (YC10) and Main PWB (YC6) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. Main PWB Replace the main PWB. |
| Error code: | 0620 |
| Description: | FAX image DIMM error 1. The Fax image DIMM has not been installed. 2. Fax image DIMM access error. |
| Causes: | DIMM installed incorrectly. Defective main PWB. |
| Remedy: | FAX image DIMM 1. Install the FAX image DIMM supplied in the FAX system onto the main PWB. 2. Firmly install the FAX image DIMM again onto the main board. 3. Check the FAX image DIMM terminals and remove any foreign objects that may be adhered to it. 4. Replace with a new FAX image DIMM. Main PWB. Replace the main PWB. |
| Error code: | 0630 |
| Description: | DMA error DMA transmission of image data does not complete within the specified period of time. |
| Causes: | Poor contact in the connector terminals. Defective main PWB. |
| Remedy: | DP CIS 1. Reconnect the CIS signal line. 2. Confirm that the CIS connector terminals are firmly connected. Insert the connector all the way in. 3. If the wiring is disconnected, shorted or grounded, replace the wiring. DP main PWB Main PWB 1. Confirm that the wiring connector is firmly connectHDD number difference 1. Confirm whether the HDD number is correct in U024_Composition and change it if different. HDD 1piece: Single HDD 2pieces: Multied and, if necessary, connect the connector all the way in. 2. If the wiring is disconnected, shorted or grounded, replace the wiring. Wiring that connects the CIS and the DP controller PWB. Wiring that connects the DP main PWB and the main PWB. 3. Replace the DP main PWB. 4. Replace the main PWB. |
| Error code: | 0640 |
| Description: | Hard disk error The hard disk cannot be accessed. |
| Causes: | Defective hard disk. Defective main PWB. |
| Remedy: | HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Lack of HDD capacity 1. Confirm the total capacity of the HDD if it is more than 320GB. Change the HDD or add it in case of lacking in capacity. Main PWB Replace the main PWB. |
| Error code: | 0650 |
| Display: | Scanner home failure CODE (0650) Turn power off, on |
| Description: | Scanner Home Failure • A low motor lock signal is not detected even after the lapse of a predetermined period of time after the Polygon Motor has been started. • The motor lock signal remains HIGH for a predetermined consecutive period of time while the Polygon Motor remains energized. |
| Causes: | • Engine Control Board, PL13.0.20 • Image Processor Board, PL2.0.4 |
| Remedy: | 1 Check connector P/J2 on the Image Processor Board. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Replace the Scanner. Does the problem persist? Go to step 3. Complete. 3 Replace the Engine Control Board. Does the problem persist? Go to step 4. Complete. 4 Replace the Power Supply. Complete. |
| Error code: | 0660 |
| Description: | Hard disk encryption key error |
| Causes: | EEPROM. HDD. Main PWB |
| Remedy: | EEPROM 1. Execute U004 if this occurs after the EEPROM has been changed. HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Main PWB Replace the main PWB. |
| Error code: | 0670 |
| Description: | Hard disk overwriting erasure error |
| Causes: | HDD. Main PWB. |
| Remedy: | HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Main PWB Replace the main PWB. |
| Error code: | 0800 |
| Display: | Print Unable 08 Turn the power off and then back on again. |
| Description: | Image processing error JAM010X is detected twice. |
| Causes: | Defective main PWB. |
| Remedy: | Main PWB Replace the main PWB. |
| Error code: | 0830 |
| Description: | FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB |
| Causes: | Defective FAX software. Defective FAX control PWB. |
| Remedy: | FAX software 1. Reinstall the fax software. FAX control PWB 1. Execute initializing by U600.(Refer to the FAX service manual) 2. Replace the FAX control PWB. |
| Error code: | 0840 |
| Description: | Faults of RTC (“Time for maintenance T” is displayed) [Check at power up] The RTC setting has reverted to a previous state. The machine has not been powered for 5 years (compared to the settings stored periodically in the EEPROM). The RTC setting is older than 00:01 on January 1, 2000. [Checked periodically (in 5- minute interval) after powered up] The RTC setting has reverted to a state older than the last time it was checked. 10 minutes have been passed since the previous check. After C840 is detected, the machine enters in disconnection mode after the main power switch has been switched on and off and indicates ‘Maintenance T.’ |
| Causes: | The battery is disconnected from the main PWB Defective main PWB. |
| Remedy: | Battery (main PWB) 1. Make sure that the back-up batteries on the main PWB are not short-circuited. 2. Reset Maintenance T by executing U906. 3. If the same C call is displayed when power is switched on and off, replace the back up battery. 4. If communication error (due to a noise, etc.) is present with the RTC on the main circuit PWB, check the PWB is properly grounded. Main PWB Replace the main PWB |
| Error code: | 0870 |
| Description: | PCFAX control PWB to main PWB high capacity data transfer error High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times. |
| Causes: | Improper installation FAX control PWB. Defective FAX control PWB or main PWB. |
| Remedy: | FAX control PWB 1. Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on. 2. Replace the FAX control PWB. HDD Execute U024 to initialize the HDD. Main PWB Replace the main PWB. |
| Error code: | 0920 |
| Description: | Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX control PWB. |
| Causes: | Defective FAX control PWB. |
| Remedy: | FAX control PWB 1. Execute initializing by U600 (Refer to the FAX service manual). 2. Replace the FAX control PWB. |
| Error code: | 0980 |
| Description: | 24 V power down detect If a 24V power disconnection signal is observed and a 12V power disconnection signal is observed simultaneously for one second. |
| Causes: | Defective power source PWB. |
| Remedy: | Power source PWB 1. Check the +24V output is given at YC12- 1 to 3 of the power circuit PWB. 2. Replace the power source PWB |
| Error code: | 1000 |
| Description: | MP lift motor error If the MP lift sensor 1 (upper limit detect) or 2 (bottom detect) is not detectable to be turned on while the MP lift motor is ascending or descending. |
| Causes: | Defective MP plate elevation mechanism. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective MP lift motor. Defective engine PWB. |
| Remedy: | Manual feed lift base elevating mechanism 1. Check that the paper lift base of the manual feed tray can smoothly ascend and descent, if not, repair or replace. 2. Check that the lift lever is located so that it can ascend or descend by the lift motor cam and that it not damaged and, if necessary, re-install or replace the manual feed table. MP lift motor 1. Check that the paper elevator has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MP lift motor and Relay PWB (YC3) Relay PWB (YC12) and Feed PWB1 (YC17) Feed PWB1 (YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the MP lift motor. MP lift sensor1 MP lift sensor2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MP lift sensor1,2 and Relay PWB (YC3) Relay PWB (YC12) and Feed PWB1(YC17) Feed PWB1 (YC1) and Engine PWB (YC6) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the MP lift sensor1 or MP lift sensor2. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1010 |
| Display: | Problem with Printhead L/R Chk printing results |
| Description: | Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1020 |
| Description: | Lift motor 2 error After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 2. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 2 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 2. Lift sensor 2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 2 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor2. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1030 |
| Display: | GARO W1221 |
| Description: | PF lift motor 1 error (paper feeder) After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 1. Replace the PF lift motor 1. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1040 |
| Display: | GL2: W0501 The memory is full. |
| Description: | PF lift motor 2 error (paper feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 2 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 2. Replace the PF lift motor 2. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1100 |
| Display: | Prepare for maint cart replacement. |
| Description: | Paper Jam There is paper jammed in the All-In-One. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Clear the paper jam, and resend the print job. |
| Error code: | 1110 |
| Description: | PF lift motor 2 error (large capacity feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 23 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively. However, the first 1 s after PF lift motor 2 is turned on is excluded from detection. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Paper feeder lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. PF Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift motor 2 and PF main PWB (YC7) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the PF Lift motor2. PF Lift sensor2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift sensor 2 and PF main PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the PF Lift sensor 2. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1140 |
| Description: | SD lift motor error (side deck) After cassette 5 is inserted, SD lift sensor does not turn on within 30 s. The lock signal of the motor is detected continuously for 200 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective SD lift motor. Defective SD main PWB. |
| Remedy: | Paper feeder lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. SD Lift motor 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SD Lift motor and SD main PWB (YC8) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the SD Lift motor. SD Lift sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. SD Lift sensor and SD main PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the SD Lift sensor. SD main PWB Replace the SD main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1400 |
| Display: | Condensation Leave switched ON. Fully open the Front Cover. Wait 30 minutes, switch OFF and close cover, then switch ON. |
| Description: | Rotary guide motor error The guide sensor is not detected to be on at the home position detection with the rotary guide for three times in a row. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective BR guide motor. Defective BR main PWB. Defective engine PWB. |
| Remedy: | Rotary guide motor 1. Check the rotary guide and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Rotary guide motor and BR PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the rotary guide motor. BR PWB Replace the BR PWB. |
| Error code: | 1410 |
| Description: | Rotary de-curler error If the de-curler won’t turn On/ Off despite it has been activated for 400 steps during waiting for the de-curler sensor to be On/Off three times in a row (3 times in succession). |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective BR decurler motor. Defective BR main PWB. Defective engine PWB. |
| Remedy: | Rotary de-curler motor 1. Check the rotary de-curler and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Rotary de-curler motor and BR PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the rotary de-curler motor. BR PWB Replace the BR PWB. |
| Error code: | 1710 |
| Description: | Side multi tray incompatible detection error The side multi tray has been installed with a device to which it is incompatible. |
| Causes: | The side multi tray is installed with a device to which it is incompatible. |
| Remedy: | The side multi tray is installed with a device to which it is incompatible. Install the side multi-tray with the target model. |
| Error code: | 1800 |
| Description: | Paper feeder communication error A communication error from paper feeder is detected 10 times in succession. |
| Causes: | Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB. |
| Remedy: | Paper feeder Check the wiring connection status with the main unit and, if necessary, try connecting it again. PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF main PWB (YC13) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the PF main PWB (Refer to the service manual for the paper feeder). Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1900 |
| Description: | Paper feeder EEPROM error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective PF main PWB. Device damage of EEPROM. |
| Remedy: | PF main PWB (EEPROM) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2101 |
| Description: | Developer motor error After developer motor is driven, the ready signal does not turn to L within 2 s. After developer motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective developer motor. Defective engine PWB. |
| Remedy: | Developer unit 1. Check that the developer waste lock has been released and, if not, release the lock. 2. Check that the gears and spiral screw of the developer unit are not damaged. 3. Confirm that the developer roller can rotate. 4. If it won`t rotate, replace the developer unit. Developer motor 1. To check the motor operation, execute DLP(K) by U030. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer motor and Feed PWB 1 (YC8) Feed PWB 1 (YC2) and Engine PWB (YC5) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Developer motor. Engine PWB. 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2201 |
| Description: | drum motor steady-state error After drum motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor. Defective engine PWB. |
| Remedy: | Drum unit 1. Confirm that the drum or the drum screw can rotate. 2. If it won’t rotate, replace the drum unit. Drum motor 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. drum motor and Feed PWB 1 (YC9) Feed PWB 1 (YC2) and Engine PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the drum motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2211 |
| Description: | Drum motor startup error Drum motor is not stabilized within 2 s since the motor is activated. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor K. Defective engine PWB. |
| Remedy: | Drum unit 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the drum or the drum screw can rotate. 3. If it won’t rotate, replace the drum unit. Drum motor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. drum motor and Feed PWB 1 (YC9) Feed PWB 1 (YC2) and Engine PWB (YC5) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the drum motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2300 |
| Description: | Fuser motor error After fuser motor is driven, the ready signal does not turn to L within 2 s. After fuser motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective fuser motor. Defective engine PWB. |
| Remedy: | Fuser motor 1. To check the motor operation, execute U030 Fuser (Fuser motor). 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser motor and Feed PWB 1(YC18) Feed PWB 1(YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the fuser motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Feed PWB 1 Replace the Feed PWB 1. Fuser unit Replace the fuser unit. |
| Error code: | 2500 |
| Description: | Paper feed motor error After paper feed motor is driven, the ready signal does not turn to L within 2 s. After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective paper feed motor. Defective engine PWB. |
| Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Feed PWB 2(YC2) Feed PWB 2(YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2550 |
| Description: | Transfer motor error After Transfer motor is driven, the ready signal does not turn to L within 2 s. After Transfer motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective fuser motor. Defective engine PWB. |
| Remedy: | Transfer motor 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Transfer motor and Relay PWB(YC6) Relay PWB(YC5) and Feed PWB 1 (YC13) Feed PWB 1 (YC2) and Engine PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Transfer motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2600 |
| Description: | PF paper feed motor error (large capacity feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 LCF- Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2810 |
| Description: | Inner waste toner motor error Initialized when an error is constantly observed for 2 seconds after the inner waste toner motor is activated. An error is detected twice for 2.5 seconds after rebooting. The lock detect signal won’t be H level three times in a row within 200 ms at 1.25 ms cycles after the inner waste toner motor has been driven. |
| Causes: | Defective connector cable or poor contact in the connector Defective drive transmission system of motor. Defective waste toner motor. Defective engine PWB. |
| Remedy: | Waste toner box 1. Rotate the waste toner spiral by the hand and check that they are not unusually loaded. 2. If the spiral won’t rotate, replace the waste toner tank. Waste toner motor 1. Rotate the drive gear by the hand and check that they are not unusually loaded. 2. Clean the drive gears and the axle holder. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Waste toner motor and Front PWB (YC16) Front PWB (YC3) and Engine PWB (YC7) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the waste toner motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 3100 |
| Description: | Scanner carriage error The home position is not correct when the power is turned on, at the end of a reading process of the table and document processor. |
| Causes: | Defective connector cable or poor contact in the connector. Defective home position sensor. Defective scanner motor. Defective ISC PWB. Defective main PWB. |
| Remedy: | The scanner mirror frame is being locked after setup. Check whether the scanner mirror frame has been unlocked and unlock if necessary. Scanner motor 1. To check the scanner motor, execute U073. 2. Move the scanner by the hand to check whether it is unusually difficult to move. 3. Check that the optical wire rope is not disengaged and engage the wire. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Scanner motor and ISC PWB (YC5) ISC PWB (YC3) and Main PWB (YC11) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the scanner motor. Home position sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Home position sensor and ISC PWB (YC8) 3. Replace the home position sensor. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3210 |
| Description: | CIS lamp error When input value at the time of CIS illumination does not exceed the threshold value between 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CIS. Defective DPSHD PWB. Defective DP relay PWB. |
| Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. Execute CCD of U061 lamp check. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CIS and execute U091 and U411. DPSHD PWB Replace the DPSHD PWB. DP relay PWB Replace the DP relay PWB. |
| Error code: | 3220 |
| Description: | CCD lamp activation error The threshold is calculated for colors at initialization and the pixel which does not exceed that value is greater than 1000. |
| Causes: | CIS. ISC PWB. Main PWB. |
| Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. If the LED lamp won’t light, replace the LED PWB and execut U411. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3300 |
| Description: | Optical system (AGC) error One of the gains is FF or 00 during the CCD lamp AGC is being processed. |
| Causes: | Defective connector cable or poor contact in the connector. Defective exposure lamp Defective CCD PWB. Defective ISC PWB. Defective main PWB. |
| Remedy: | LED lamp PWB 1. To check the lamp, execute U061 CCD. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. If the LED lamp won’t light, replace the LED PWB and execut U411. CCD PWB Replace the ISU and execute U411. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3310 |
| Description: | CIS AGC error After AGC, correct input is not obtained at CIS. |
| Causes: | Defective CIS. Defective DPSHD PWB. Defective DP relay PWB. |
| Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. To check the lamp, execute U061 CCD. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CIS and execute U091 and U411. DPSHD PWB Replace the DPSHD PWB. |
| Error code: | 3500 |
| Description: | Communication error between scanner and ASIC An error code is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective ISC PWB. Defective main PWB. |
| Remedy: | ISC PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ISC PWB (YC3) and Main PWB (YC11) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3600 |
| Description: | Scanner sequence error |
| Causes: | Defective ISC PWB. |
| Remedy: | ISC PWB 1. Execute U021 memory initializing. 2. Replace the ISC PWB and execute U411. |
| Error code: | 3700 |
| Description: | Scanner device error |
| Causes: | CCD connector inserted incorrectly. |
| Remedy: | CCD (ISU) Since the ISU is mounted with a CCD of different type, install the ISU that matches with the model. |
| Error code: | 3800 |
| Description: | AFE error When writing the data, read and write data does not match 3 times in succession. No response is received in 100 ms from AEF. |
| Causes: | Defective ISC PWB. |
| Remedy: | ISC PWB 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. CCD PWB (YC2) and ISC PWB (YC9) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the ISC PWB and execute U411. CCD PWB Replace the ISU and execute U411. |
| Error code: | 3900 |
| Description: | Backup memory read/write error (ISC PWB) Read and write data does not match. |
| Causes: | Defective backup memory or PWB. |
| Remedy: | Backup memory (ISC PWB) 1. Turn the main power switch off and after 5 seconds, turn it on. 2. Replace the ISC PWB and execute U411. |
| Error code: | 4001 |
| Display: | ERROR E146-4001 Call for service. |
| Description: | Polygon motor synchronization error After polygon motor is driven, the ready signal does not turn to L within 30 s. The polygon motor speed won’t stabilize within 10 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Polygon motor (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor and Engine PWB (YC15) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4011 |
| Description: | Polygon motor steady-state error After Polygon motor is stabilized, the ready signal is at the H level for 15 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Polygon motor (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor and Engine PWB (YC15) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4101 |
| Description: | BD initialization error K After Polygon motor is driven, the BD signal is not detected for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB. Defective engine PWB. |
| Remedy: | PD PWB K (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4201 |
| Display: | Replace Drum:BK |
| Description: | BD steady-state error K The BD signal is not detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB. Defective engine PWB. |
| Remedy: | PD PWB K (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, shorted or grounded, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 5101 |
| Description: | Main high-voltage error K Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower highvoltage board). |
| Causes: | Defective connector cable or poor contact in the connector. Defective high voltage PWB Defective engine PWB. |
| Remedy: | Drum unit 1. Confirm that the drum or the drum screw can rotate. 2. If it won’t rotate, replace the drum unit. 3. Check that the discharger lamp is properly connected. Charger roller unit 1. Check that the high-voltage contacts are not distorted or adhered with foreign objects. 2. Reinstall the chrager roller unit.Or, replace the charger roller unit. High voltage PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. High voltage PWB (YC2) and Engine PWB (YC16) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the High voltage PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6000 |
| Description: | Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6030 |
| Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6040 |
| Description: | Fuser heater error Input from fuser center thermistor 1 is abnormal value continuously for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Center thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6050 |
| Description: | Abnormally low fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up, during ready or during print. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 1. Defective fuser heater. Defective engine PWB. |
| Remedy: | Power source 1. Check that the operating voltage falls within +/-10%. 2. Check no voltage drop is caused. The heater is deactivated at 70V or lower. 3. Relocate the AC outlet that supplies power. Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 1. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6200 |
| Display: | No Drum Unit Install the Drum Unit. |
| Description: | Broken fuser edge heater wire Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up. The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser center thermistor 1 1. Replace the Fuser unit. |
| Error code: | 6220 |
| Description: | Abnormally high fuser edge thermistor temperature Fuser thermistor 2 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 2. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6230 |
| Description: | Broken fuser edge thermistor wire The Input signal from the fuser thermistor 2 is 992 or more (A/D value) continuously for 1 s when the temperature at the fuser thermistor 1 is higher than 100°C/212°F. Fuser thermistor 2 detects a lower then 50°C/122°F for 15s during warming up. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 2 wire. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6250 |
| Description: | Abnormally low fuser edge thermistor temperature Fuser thermistor 2 detects a temperature lower than 100°C/212°F for 1 s during ready or print. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 2. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Fuser unit and Engine PWB (YC26) If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6320 |
| Description: | Abnormally high fuser middle thermistor 3 temperature Fuser middle thermistor 3 detects a temperature higher than 215°C/419°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 3. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6400 |
| Display: | No Belt Unit Open the Front Cover, pull out all Drum Units completely and install the Belt Unit. |
| Description: | Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s. |
| Causes: | Fuser unit. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser heater PWB (YC2) and feed PWB 1 (YC27) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser heater PWB. |
| Error code: | 6610 |
| Description: | Fuser release sensor error When the fuser release motor is driven, the fuser release sensor does not turn on/off for 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective fuser release motor. Defective engine PWB. |
| Remedy: | Fuser release motor 1. To check the motor operation, execute U030 Fuser Release. 2. Check that the drive gear can be rotated and the separation is possible. 3. If the motor won’t rotate, confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Fuser unit. Fuser release sensor 1. Check that the sensor is correctly positioned. 2. Check that the sensor is not contaminated or damaged. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6910 |
| Description: | Engine software ready error The device won’t engage in ready state in 60 minutes after warming-up has began. (A previous timeout process has not been cancelled. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser rear fan motor. Defective engine PWB. |
| Remedy: | Engine PWB 1. Turn the main power switch off and after 5 seconds, turn it on. 2. Reinstall the engine software. 3. Replace the engine PWB. |
| Error code: | 7001 |
| Description: | Toner motor error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective toner motor. Defective engine PWB. |
| Remedy: | Toner container 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Screw sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor and Front PWB (YC5) Front PWB (YC2) and Engine PWB (YC7) 3. Replace the Screw sensor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7101 |
| Description: | Toner sensor error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective toner sensor. Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the Developer unit are not damaged and the spiral can rotate. 5. Replace the Developer unit. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7200 |
| Display: | Jam MP Tray Remove the jammed paper from MP Tray and press [Retry]. |
| Description: | Broken outer temperature sensor 2 wire The sensor input sampling is greater than 230. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 2 1. Confirm Ext/Int is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor 2 and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the outer temperature sensor 2. Front PWB Replace the front PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7210 |
| Description: | Short-circuited outer temperature sensor The sensor input sampling is less than 69. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 2 1. Confirm Ext/Int is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor 2 and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the outer temperature sensor 2. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7221 |
| Description: | Broken LSU thermistor wire The sensor input sampling is greater than 230. |
| Causes: | Defective connector cable or poor contact in the connector. Defective LSU thermistor. Defective engine PWB. |
| Remedy: | LSU thermistor 1. Confirm LSU is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the laser scanner unit. LSU relay PWB REPLACE the LSU relay PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7231 |
| Description: | Short-circuited LSU thermistor The sensor input sampling is less than 69. |
| Causes: | Defective connector cable or poor contact in the connector. Defective LSU thermistor. Defective engine PWB. |
| Remedy: | LSU thermistor 1. Confirm LSU is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the laser scanner unit. LSU relay PWB Replace the LSU relay PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7241 |
| Description: | Broken developer thermistor wire The sensor input sampling is greater than 230. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer thermistor. Defective engine PWB. |
| Remedy: | Developer thermistor 1. Confirm Developing is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Developer unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7251 |
| Description: | Short-circuited developer thermistor The sensor input sampling is less than 69. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer thermistor. Defective engine PWB. |
| Remedy: | Developer thermistor 1. Confirm Developing is displayed by U139 temperature and humidity. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Developer unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7301 |
| Description: | Toner hopper motor error During the Toner hopper motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective toner hopper sensor. Defective toner hopper motor. Defective engine PWB. |
| Remedy: | Toner hopper motor 1. If the motor won’t rotate, confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner hopper motor and Front PWB (YC5) Front PWB (YC3) and Engine PWB (YC7) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the toner hopper motor. Screw sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor and Front PWB (YC5) Front PWB (YC2) and Engine PWB (YC7) 3. Replace the Screw sensor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7401 |
| Description: | Developer unit type mismatch error Improper adaptation of the machine and developer unit is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
| Remedy: | Different type of the developer unit is installed. Install the developer unit of the correct type. Developer unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
| Error code: | 7460 |
| Description: | Developer shutter error Power is turned on while the developer shutter is locked. |
| Causes: | The developer shutter has been locked. Defective connector cable or poor contact in the connector. |
| Remedy: | The developer shutter has been locked. Release the developer shutter. Developer shutter sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer shutter sensor and Front PWB (YC4) Front PWB (YC3) and Engine PWB (YC7) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
| Error code: | 7601 |
| Description: | ID sensor 1 error [Front] Dark potential error FrontDarkP and FrontDarkS are greater than 0.80V. Light potential error FrontBrightS is smaller than FrontDarkS. FrontBrightP is smaller than [FrontDarkP + 0.5V]. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | ID sensor1 1. Execute U464 Calib for setting ID compensation operation and check the displayed values by U465 Boas Calib for ID compensation reference. 2. Clean the ID sensor on its surface. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ID sensor 1 (front) and relay PWB (YC10) Relay PWB (YC1) and Feed PWB 1 (YC14) Feed PWB 1 (YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. Feed PWB 1 Replace the Feed PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7602 |
| Description: | ID sensor 2 error [Rear] Dark potential error RearDarkP and RearDarkS are greater than 0.80V. Light potential error RearBrightS is smaller than RearDarkS. RearBrightP is smaller than [RearDarkP + 0.5V]. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | ID sensor 2 1. Execute U464 Calib for setting ID compensation operation and check the displayed values by U465 Boas Calib for ID compensation reference. 2. Clean the ID sensor on its surface. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ID sensor2 (rear) and relay PWB (YC10) Relay PWB (YC1) and Feed PWB 1 (YC14) Feed PWB 1 (YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. Feed PWB 1 Replace the Feed PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7800 |
| Description: | Broken outer temperature sensor wire The device did not respond for more than 5 ms during reading, in 5 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Outer temperature sensor. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7901 |
| Description: | Drum EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB. |
| Remedy: | DR PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DR PWB and Front PWB (YC6) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7911 |
| Description: | Developer unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer unit. |
| Remedy: | Developer unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7941 |
| Description: | Laser scanner unit EEPROM error Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective APC PWB. |
| Remedy: | APC PWB 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. APC PWB and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, shorted or grounded, replace the FFC wiring. 3. Replace the laser scanner unit. LSU relay PWB Replace the LSU relay PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 8010 |
| Description: | Punch motor error 1 When the punch motor is driven, punch home position sensor does not turn on within 200 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch home position sensor. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch home position sensor 1. Execute U241 Punch - Punch HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch home position sensor and Punch PWB (YC8) 4. Replace the Punch home position sensor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8020 |
| Description: | Punch motor error 2 Home position is not obtained in 3 s after home position is initialized or in standby. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8030 |
| Description: | Punch motor error 3 Home position does not turn from On to Off in 50 ms after home position has been initialized. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8090 |
| Description: | DF paddle motor error When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF paddle sensor. Defective DF paddle motor. Defective DF main PWB. |
| Remedy: | DF paddle motor 1. Execute U240 Motor - Beat to check the finisher operation. 2. Check that the paddle can rotate. 3. Check that the drive from the motor reaches the paddle. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF paddle motor and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF paddle motor. DF paddle sensor 1. Execute U241 Finisher - Bundle Eject HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF paddle sensor and DF main PWB (YC22) 4. Replace the DF paddle sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8100 |
| Description: | DF eject release motor error When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF bundle discharge sensor. Defective DF eject release motor. Defective DF main PWB. |
| Remedy: | DF eject release motor DF bundle discharge unit sensor 1. Execute U240 Motor - Eject Unlock (Full) to check the finisher operation. 2. Check that the eject guide of the process tray is opened and, if not, correct the guide. 3. Check that the drive from the motor reaches the eject guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF bundle discharge unit sensor and DF main PWB (YC22) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF eject release motor. DF bundle discharge unit sensor 1. Execute U241 Finisher - Bundle Eject HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF bundle discharge unit sensor and DF main PWB (YC22) 4. Replace the DF bundle eject unit sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8110 |
| Description: | DF shift motor 1 error DF shift sensor 1 won’t turn on when it has travelled 160 mm after DF shift motor 1 is driven. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF shift sensor 1. Defective DF shift motor 1. Defective DF main PWB. |
| Remedy: | DF shift motor 1 [front] 1. Execute U240 Motor - Sort Test to check the finisher operation. 2. Manipulate the front shift guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the front shift guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift motor 1[front] and DF main PWB (YC14) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF shift motor 1 [front]. DF shift sensor 1 [front] 1. Execute U241 Finisher - Shift Front HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift sensor 1[front] and DF main PWB (YC23) 4. Replace the DF shift sensor 1 [front]. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8120 |
| Description: | DF shift motor 2 error DF shift sensor 2 won’t turn on when it has travelled 160 mm after DF shift motor 2 is driven. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF shift sensor 2. Defective DF shift motor 2. Defective DF main PWB. |
| Remedy: | DF shift motor 2 [rear] 1. Execute U240 Motor - Sort Test to check the finisher operation. 2. Manipulate the rear shift guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the rear shift guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift motor 2 [rear] and DF main PWB (YC14) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF shift motor 2 [rear]. DF shift sensor 2 [rear] 1. Execute U241 Finisher - Shift Tail HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift sensor 2 [rear] and DF main PWB (YC23) 4. Replace the DF shift set sensor2 [rear]. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8130 |
| Description: | DF shift release motor error When the DF shift release motor is driven, DF shift release sensor does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF shift release sensor. Defective DF shift release motor. Defective DF main PWB. |
| Remedy: | DF shift release motor 1. Check that cancelling the maintenance mode after executing U240 Motor - Sort for the finisher operation check lets the rear and forth cursors return to the home position. 2. Manipulate the front and rear shift guide to check it is smoothly operable. 3. Check that the drive from the motor reaches the shift guide front and rear. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift release motor and DF main PWB (YC14) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF shift release motor. DF shift release sensor 1. Execute U241 Finisher - Shift Unlock HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF shift release sensor and DF main PWB (YC23) 4. Replace the DF shift release sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8140 |
| Description: | DF tray motor error 1 When the main tray has ascended, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF Main PWB(YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF Main PWB(YC22) DF tray upper surface sensor and DF Main PWB(YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8150 |
| Description: | DF tray motor error 2 When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF main PWB (YC22) DF tray upper surface sensor and DF main PWB (YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8160 |
| Description: | DF tray motor error 3 When the main tray has descended, DF tray sensor 4 does not turn on within 20 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF tray sensor 3. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 4 1. Execute U241 Finisher - Tray Middle to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 4 and DF main PWB (YC23) 4. Replace the DF tray sensor 4. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8170 |
| Description: | DF side registration motor 1 error 1 When initial operation, DF side registration sensor 1 does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8180 |
| Description: | DF side registration motor 1 error 2 JAM6810 (jam in front of width alignment) is detected twice. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1. 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8190 |
| Description: | DF side registration motor 2 error 1 When initial operation, DF side registration sensor 2 does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 2. Defective DF side registration motor 2. Defective DF main PWB. |
| Remedy: | DF side registration motor 2 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the rear side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the rear side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 2 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 2. DF side registration sensor 2 1. Execute U241 Finisher - Width tail HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 2 and DF main PWB (YC22) 4. Replace the DF side registration sensor 2. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8200 |
| Description: | DF side registration motor 2 error 2 JAM6910 (jam in rear of width alignment) is detected twice. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 2. Defective DF side registration motor 2. Defective DF main PWB. |
| Remedy: | DF side registration motor 2 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the rear side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the rear side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 2 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 2. DF side registration sensor 2 1. Execute U241 Finisher - Width tail HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 2 and DF main PWB (YC22) 4. Replace the DF side registration sensor 2. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8210 |
| Description: | DF slide motor error When initial operation, DF staple sensor does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF slide motor. Defective DF main PWB. |
| Remedy: | DF slide motor 1. Execute U240 Motor - Staple Move to check the finisher operation. 2. Manipulate the staple unit back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the staple unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF slide motor and DF main PWB (YC12) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF slide motor. DF staple sensor 1. Execute U241 Finisher - Width Staple HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF staple sensor and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF staple sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8230 |
| Description: | DF staple motor error 1 Staple JAM (DF) has been detected twice in a row. (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF staple motor. Defective DF main PWB. |
| Remedy: | DF staple motor 1. Remove the staple unit and check that stapling is possible without a jam. 2. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Staple unit and DF main PWB (YC17) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the staple unit. (Refer to the service manual for the document finisher). DF staple sensor Replace the staple unit. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8240 |
| Description: | DF staple motor error 2 Staple JAM (DF) has been detected twice in a row. (The second JAM detection condition fullfilled with a lock detection signal maintained 1 V for 500 ms continuously, while the stapler motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple motor. Defective DF main PWB. |
| Remedy: | DF staple motor 1. Remove the staple unit and check that stapling is possible without a jam. 2. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Staple unit and DF main PWB (YC17) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the staple unit. (Refer to the service manual for the document finisher). DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8250 |
| Description: | DF tray motor error 4 The lock signal of the motor is detected continuously for 10 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF tray motor and DF main PWB (YC16) DF tray sensor 3 and DF main PWB (YC23) Defective DF tray motor. Replace the DF tray motor. Defective DF main PWB. Replace the DF main PWB and check for correct operation. |
| Error code: | 8300 |
| Description: | CF unit communication error Communication with the center- folding unit is not possible. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF set sensor. Defective PWB. |
| Remedy: | CF unit set switch 1. Execute U241 Booklet - Set to check the finisher switch. 2. Check that the switch and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF main PWB (YC7) and DF main PWB (YC9) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CF unit set switch. CF main PWB Replace the CF main PWB DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8310 |
| Description: | CF side registration motor 2 error When initial operation, CF side registration sensor 2 does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF side registration sensor 2. Defective CF side registration motor 2. Defective CF main PWB. |
| Remedy: | CF side registration motor 2 1. Execute U240 Booklet - Width Test to check finisher operation check. 2. Manipulate the side registration upper guide back and forth to check it can smoothly move back and forth. 3. Check that the drive from the motor reaches the side registration upper guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration motor 2 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF side registration motor. CF side registration sensor 2 1. Execute U241 Booklet - Width Up HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration sensor 2 and CF main PWB (YC20) 4. Replace the CF side registration sensor 2. CF main PWB Replace the CF main PWB |
| Error code: | 8320 |
| Description: | CF adjustment motor error When initial operation, CF adjustment sensor does not turn on within 2.5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF adjustment sensor 1, 2. Defective CF adjustment motor 1, 2. Defective CF main PWB. |
| Remedy: | CF adjustment motor1,2 1. Execute U240 Booklet - Bundle Up / Down to check the finisher operation. 2. Manipulate the fold moving belt up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the fold moving belt. (Check if the belt is bent.) 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF adjustment motor 1,2 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF adjustment motor1,2 CF adjustment sensor1,2 1. Execute U241 Booklet - bundle Up / Down HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF adjustment sensor 1,2 and CF main PWB (YC20) 4. Replace the CF adjustment sensor1,2. CF main PWB Replace the CF main PWB. |
| Error code: | 8330 |
| Description: | CF blade motor error When initial operation, CF blade sensor does not turn on within 1500 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF blade sensor. Defective CF blade motor. Defective CF main PWB. |
| Remedy: | CF blade motor 1. Execute U240 Booklet - Blade to check the finisher operation. 2. Manipulate the fold blade up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the fold blade. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF blade motor and CF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF blade motor. CF blade sensor 1. Execute U241 Booklet - Blade HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF blade sensor and CF main PWB (YC20) 4. Replace the CF blade sensor. CF main PWB Replace the CF main PWB |
| Error code: | 8340 |
| Description: | CF staple motor error 1 Staple JAM (center-folding unit) has been detected twice in a row. (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF staple sensor. Defective CF staple motor. Defective CF main PWB. |
| Remedy: | CF staple motor 1. Execute U240 Booklet - Staple to check the finisher operation. 2. Manipulate the staple up and down check it is smoothly operable. 3. Check that the drive from the motor reaches the staple unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF staple unit and CF main PWB (YC13) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF staple motor. CF staple sensor Replace the CF staple unit. CF main PWB Replace the CF main PWB. |
| Error code: | 8350 |
| Description: | CF side registration motor 1 error When initial operation, CF side registration sensor 1 does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF side registration sensor 1. Defective CF side registration motor 1. Defective CF main PWB |
| Remedy: | CF side registration motor 1 1. Execute U240 Booklet - Width Test to check the finisher operation. 2. Manipulate the side registration lower guide back and forth to check it can smoothly operable. 3. Check that the drive from the motor reaches the side registration lower guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration motor 1 and CF main PWB (YC10) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF side registration motor 1. CF side registration sensor 1 1. Execute U241 Booklet - Width Down HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF side registration sensor 1 and CF main PWB (YC20) 4. Replace the CF side registration sensor 1. CF main PWB Replace the CF main PWB |
| Error code: | 8360 |
| Description: | CF main motor error During driving the motor, the lock signal is detected for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF main motor. Defective CF main PWB. |
| Remedy: | CF main motor 1. Execute U240 Booklet - Folding to check the finisher operation. 2. Manipulate the conveying roller to check it can smoothly rotate. 3. Check that the drive from the motor reaches the conveying roller. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF main motor and CF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the CF main motor. CF main PWB Replace the CF main PWB |
| Error code: | 8370 |
| Description: | CF staple motor error 2 (4000-sheet finisher) Staple JAM (DF) has been detected twice in a row. (The home position could not be detected in 600 ms since the motor was driven after jam was detected twice.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective CF staple motor. Defective CF main PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CF staple unit and CF main PWB (YC13) Defective CF staple motor. Replace the CF staple unit. Defective CF main PWB. Replace the CF main PWB and check for correct operation. |
| Error code: | 8410 |
| Description: | Punch slide motor error 1 The punch slide sensor won’t turn On when home position has been moved by 30 mm. |
| Causes: | Defective connector cable or poor contact in the connector. Defective slide sensor. Defective punch slide motor. Defective PWB. |
| Remedy: | Punch slide motor 1. Execute U240 Booklet - Punch Move to check the finisher operation. 2. Manipulate the punch slide part of the punch unit back and forth to check it can smoothly move. 3. Check that the drive from the motor reaches punch part. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide motor and Punch PWB (YC3) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch slide motor. Punch slide sensor 1. Execute U241 Punch - Punch HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide sensor and Punch PWB (YC6) 4. Replace the punch slide sensor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8420 |
| Description: | Punch slide motor error 2 In detection of paper edges, the paper edge cannot be detected in 30 mm move. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch slide motor. Defective PWB. |
| Remedy: | Punch slide motor 1. Execute U240 Booklet - Punch Move to check the finisher operation. 2. Manipulate the punch slide part of the punch unit back and forth to check it can smoothly move. 3. Check that the drive from the motor reaches punch part. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide motor and Punch PWB (YC3) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch slide motor. Punch paper edge sensor 1,2 1. Execute U241 Punch - Edge Face 1,2,3,4 to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch paper edge sensor 1,2 and Punch PWB (YC5,YC7) 4. Replace the punch paper edge sensor 1,2. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the Punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8430 |
| Description: | Punch unit communication error Communication with the punch unit is not possible. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8500 |
| Description: | Mailbox communication error Communication failed to be established after the mailbox was hooked up. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | MB main PWB 1. Turn the main power switch off and after 5 seconds, turn it on. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB main PWB (YC3) and DF main PWB (YC6) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the MB main PWB DF main PWB Replace the DF main PWB |
| Error code: | 8510 |
| Description: | MB conveying motor error 1 When initial operation, MB home position sensor does not turn on within 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective MB home position sensor. Defective MB conveying motor. Defective MB main PWB. |
| Remedy: | MB conveying motor 1. If the transfer roller won’t rotate smoothly, repair its mechanism. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB conveying motor and MB main PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the MB conveying motor. MB home position sensor 1. Execute U241 Mail Box - Motor HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB home position sensor and MB main PWB (YC2) 4. Replace the MB home position sensor. MB main PWB Replace the MB main PWB |
| Error code: | 8520 |
| Description: | MB conveying motor error 2 When standby operation, MB home position sensor does not turn off within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective MB home position sensor. Defective MB conveying motor Defective MB main PWB. |
| Remedy: | MB conveying motor 1. Execute Mail Box - Conv of U240 finisher operation check. 2. Manipulate the conveying roller of the mailbox to check it can smoothly rotate. 3. Check that the drive from the motor reaches the conveying roller. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB conveying motor and MB main PWB (YC5) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the MB conveying motor. MB home position sensor 1. Execute U241 Mail Box - Motor HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. MB home position sensor and MB main PWB (YC2) 4. Replace the MB home position sensor. MB main PWB Replace the MB main PWB |
| Error code: | 8800 |
| Description: | Document finisher main program error Document finisher main program error at power up. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | DF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF main PWB (YC4) and Engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the DF main PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 8900 |
| Description: | Document finisher backup error Read and write data does not match 3 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Improper installation EEPROM. Defective DF main PWB. |
| Remedy: | DF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF main PWB (YC4) and Engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the DF main PWB |
| Error code: | 8930 |
| Description: | Center-folding unit backup error Read and write data does not match 3 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Improper installation EEPROM. Defective CF main PWB. |
| Remedy: | CF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CF main PWB (YC7) and DF main PWB (YC9) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Install the EEPROM properly. 4. Replace the CF main PWB |
| Error code: | 9000 |
| Description: | Document processor communication error Communication with the document processor is not possible. |
| Causes: | Defective connector cable or poor contact in the connector Defective PWB. |
| Remedy: | DP main PWB 1. Check that the versions of the main unit firmware and the DP firmware are identical. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP main PWB(YC1) and ISC PWB(YC12) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the DP main PWB ISC PWB Replace the ISC PWB. |
| Error code: | 9010 |
| Description: | Coin vender communication error A communication error from coin vender is detected 10 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Data setup failure. Defective coin vender control PWB. Defective PWB. |
| Remedy: | U206 setting Set maintenance mode U206 to off when a coin vender is not installed. Coin vender control PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Coin vender control PWB and Engine PWB (YC23) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Coin vender control PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 9040 |
| Description: | DP lift motor going up error When the DP lift motor is driven, DP lift sensor 1 does not turn on within 1500 pulse. (Three recovery times.) The above has been detected 5 times. * : The number of detection should be weighted with one for the rise at job start and two for the irregular rise during transporting. The accumulated number must be cleared at completion of a normal rise. The default threshold is 5. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DP lift sensor 1. Defective DP lift motor. Defective DP main PWB. |
| Remedy: | DP lift motor 1. Execute U906 Separating Operation Release. 2. Execute U243 Lift Motor to check the DP motor operation. 3. Check that the original document lift guide can move upwards. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift motor and DP main PWB (YC5) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DP lift motor. DP lift sensor 1 1. Execute U244 Lift L-Limit to check DP switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift sensor 1 and DP main PWB (YC4) 4. Replace the DP lift sensor 1. DP main PWB Replace the DP main PWB |
| Error code: | 9050 |
| Description: | DP lift motor going down error When the DP lift motor is driven, DP lift sensor 2 does not turn on within 1500 pulse. (Three recovery times.) The above has been detected 1 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DP lift sensor 2. Defective DP lift motor. Defective DP main PWB. |
| Remedy: | DP lift motor 1. Execute U906 Separating Operation Release. 2. Execute U243 Lift Motor to check the DP motor operation. 3. Check that the original document lift guide can move downwards. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift motor and DP main PWB (YC5) If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DP lift motor. DP lift sensor 2 1. Execute U244 Lift L-Limit to check DP switch. 2. Confirm that the DP lift sensor 2 has been firmly fitted. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift sensor 2 and DP main PWB (YC2) 4. Replace the DP lift sensor2. DP main PWB Replace the DP main PWB |
| Error code: | 9060 |
| Description: | DP EEPROM error Mismatch of reading data from two locations occurs 3 times successively. Mismatch between writing data and reading data occurs 3 times successively. |
| Causes: | Defective DP main PWB. Device damage of EEPROM. |
| Remedy: | DP main PWB 1. Execute U906 Separating Operation Release. 2. Confirm that the EEPROM has been properly installed. 3. Replace the DP main PWB Device damage of EEPROM Contact the Service Support. |
| Error code: | 9070 |
| Description: | Communication error between DP and SHD A communication error is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DPSHD PWB. |
| Remedy: | DP SHD PWB 1. Execute U906 Separating Operation Release. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP SHD PWB (YC1) and DP main PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the DP SHD PWB. |
| Error code: | 9080 |
| Description: | LED fault detection A block is existent below a peak which was obtained by activating the LEDs in the four CIS blocks at power on, which is less than 80hex. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CIS Defective DPSHD PWB. |
| Remedy: | DP CIS 1. Execute CIS automatic original document alignment by U411. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CIS and DP SHD PWB (YC2) DP SHD PWB (YC1) and DP main PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the CIS and execute U411. DP SHD PWB Replace the DP SHD PWB. |
| Error code: | 9100 |
| Description: | Coin vender control PWB error Communication error has been detected at the coin mec of the coin vender control PWB. |
| Causes: | Defective coin vender control PWB. |
| Remedy: | Coin vender control PWB Replace the coin mec. |
| Error code: | 9110 |
| Description: | Coin vender rejector error Communication error has been detected in connection with the coin mec and the rejector. |
| Causes: | Rejector installed incorrectly. Defective rejector. |
| Remedy: | Rejector 1. Check that the rejector is firmly installed and, if not, install firmly. 2. Replace the rejector. |
| Error code: | 9120 |
| Description: | Sensor error in coin vender change (Yen 10) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Coin jam in the change tube Check visually and remedy. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9130 |
| Description: | Sensor error in coin vender change (Yen 50) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Coin jam in the change tube Check visually and remedy. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9140 |
| Description: | Sensor error in coin vender change (Yen 100) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Coin jam in the change tube Check visually and remedy. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9150 |
| Description: | Sensor error in coin vender change (Yen 500) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Change tube Check no exchange jam is observed at the outlet and, if necessary, repair it. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9160 |
| Description: | Coin vender pay-out error Coin is paid out despite the pay-out motor is determined not active. |
| Causes: | Defective pay-out motor. |
| Remedy: | Pay-out motor Replace the coin mec. |
| Error code: | 9170 |
| Description: | Coin vender pay-out sensor error Coin is paid out despite the pay-out motor is determined not active. |
| Causes: | Change jam at the pay-out. Defective pay-out motor. Defective pay-out sensor. |
| Remedy: | Pay-out area Check no exchange jam is observed at the outlet and, if necessary, repair it. Pay-out motor Replace the coin mec. Pay-out sensor Replace the coin mec. |
| Error code: | 9500 |
| Description: | ISC PWB error A |
| Causes: | Main PWB. ISC PWB. |
| Remedy: | Main PWB ISC PWB 1. Reinsert the connector if its connection is loose. Main PWB (YC25) and ISC PWB (YC4) 2. Replace the main PWB. 3. Replace the ISC PWB 4. Contact the Service Support. |
| Error code: | 9510 |
| Description: | ISC PWB error B |
| Causes: | Main PWB. DP SHD PWB. |
| Remedy: | Main PWB DP SHD PWB 1. Reinsert the connector if its connection is loose. DP relay PWB (YC2) and DP SHD PWB (YC3) 2. Replace the main PWB. 3. Replace the DP SHD PWB. 4. Contact the Service Support. |
| Error code: | 9520 |
| Description: | ISC PWB error C |
| Causes: | Main PWB. ISC PWB. |
| Remedy: | Main PWB ISC PWB 1. Reinsert the connector if its connection is loose. Main PWB (YC25) and ISC PWB (YC4) 2. Replace the main PWB. 3. Replace the ISC main PWB 4. Contact the Service Support. |
| Error code: | 9940 |
| Description: | Confidential document guard uninstalled error The confidential document guard PWB is removed while the confidential document guard PWB is valid. |
| Causes: | Confidential document guard PWB |
| Remedy: | Confidential document guard PWB 1. Check that the confidential document guard PWB is firmly installed and, if not, install firmly. 2. Replace the confidential document guard PW. |
| Error code: | 9950 |
| Description: | ISC PWB error C FPGA configuration error CPU version information error This is caused when the PWB of a double-side scanning DP is connected, the confidential guard PWB is inserted, and the harness is not correctly connected |
| Causes: | Confidential document guard PWB |
| Remedy: | Confidential document guard PWB 1. Replace the confidential document guard PW. 2. Replace the main PWB. |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F041 |
| Description: | Over than available setting number tray detection error |
| Causes: | Over than available setting number tray is installed. |
| Remedy: | Remove the available setting number tray. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F051 |
| Description: | Scanner engine program error |
| Causes: | The scanner program cannot start up |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The scanner engine RAM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the SSD The SSD is not properly attached. Reattach the SSD. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F278 |
| Description: | Secondary power source error |
| Causes: | The operation became unstable since the primary supply power dropped out temporarily and recovered. |
| Remedy: | 1 Resetting the main power The power reset was performed immediately. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected or the wire is faulty. Clean the connectors on the LVU and reinsert the wire connectors. If there is no continuity, replace the wire. 3 Replacing the LVU The LVU is faulty. Replace the LVU. |
