Kyocera TASKalfa 2551ci
Рейтинг
Модули
(Узел термозакрепления)
Paper Conveying Section 3
Paper Conveying Section 1
Electrical Components 1
Frames 4
Drive Section 5
Fuser Section
Covers 2
Paper Feed Section 5
Image Formation Section
PAPER CASSETTE
PANEL
Covers 1
FRAMES 2
Operation Sectionents 3
Paper Feed Section 1
(Комплекты)
FRAMES 1
Frames 5
DRIVE SECTION 2
TRANSFER SECTION
Scanner Section 1
Inner Section 1
Frames 3
Drive Section 1
ELECTRICAL COMPONENTS 2
MECH-031
Exit Section
Inner Section 2
PAPER FEED
Electrical Components 3
PAPER FEED SECTION 2
COVERS and LABELS
Laser Scanner Sectionon
(Электронные компоненты)
COOLING SECTION
Paper Conveying Section 2
Paper Conveying Section 4
Paper Feed Section 4
Paper Feed Section 3
SCANNER SECTION 2
Developer Section
DRIVE SECTION 4
(Узел переноса)
DRIVE SECTION 3
ADF 1
DUPLEX
Детали ELECTRICAL COMPONENTS 2
| Деталь: | ELA UNIT-TRANSFER |
| Парткод: | TR-8315B |
| Цена: | 4 200 ₽ |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325C |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325K |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325M |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325Y |
| Деталь: | Formatter, exchange, HP Color LaserJet 3000dn and 3000dtn Series only (256 MB) |
| Парткод: | 302NP94151 |
| Цена: | 81 100 ₽ |
| Деталь: | LASER SCANNER ASSY |
| Парткод: | LK-8325 |
| Цена: | 22 600 ₽ |
| Деталь: | Правая часть узла термозакрепления, в сборе (220В) |
| Парткод: | FK-8325 |
| Цена: | 28 900 ₽ |
| Деталь: | Левая часть узла термозакрепления, в сборе (220В) |
| Парткод: | FK-8507 |
| Цена: | 15 900 ₽ |
| Деталь: | Комплект для технического обслуживания |
| Парткод: | MK-8325B |
| Деталь: | Комплект для технического обслуживания |
| Парткод: | MK-8325A |
| Деталь: | HOLDER TRANSFER |
| Парткод: | -302K024050 |
| Деталь: | PLATE SEPARATION |
| Парткод: | -302K324150 |
| Деталь: | HOLDER SEPARATION |
| Парткод: | -302K024060 |
| Деталь: | LEVER HOOK F |
| Парткод: | -302MV24010 |
| Деталь: | SPRING TRANSFER R |
| Парткод: | -302MV24050 |
| Деталь: | BUSH TRANSFER ROLL R |
| Парткод: | -302K324430 |
| Деталь: | SPRING TRANSFER F |
| Парткод: | -302K024170 |
| Деталь: | BUSH TRANSFER ROLL F |
| Парткод: | -302K324240 |
| Деталь: | SPRING GUIDE |
| Парткод: | -302K024200 |
| Деталь: | SPRING GUIDE R |
| Парткод: | -302K024340 |
| Деталь: | GUIDE TRANSFER RIGHT |
| Парткод: | -302K024120 |
| Деталь: | PARTS ROLLER TRANSFER SP |
| Парткод: | -302MV94330 |
| Деталь: | LEVER TRANSFER |
| Парткод: | -302K024091 |
| Деталь: | SHEET TRANSFER |
| Парткод: | -302K024350 |
| Деталь: | GEAR TRANSFER Z25 |
| Парткод: | -302K024410 |
| Деталь: | HOOK TRANSFER F |
| Парткод: | -302K024070 |
| Деталь: | LABEL I |
| Парткод: | -302MV34180 |
| Деталь: | TERMINAL TRANSFER A |
| Парткод: | -302K024130 |
| Деталь: | HOOK TRANSFER R |
| Парткод: | -302K024080 |
| Деталь: | LEVER HOOK R |
| Парткод: | -302MV24020 |
| Деталь: | TR-8315B |
| Парткод: | 302MV93080 |
| Деталь: | GUIDE RIGHT COVER |
| Парткод: | -302K029016 |
| Деталь: | BUSH 8 |
| Парткод: | -302H024830 |
| Деталь: | SHAFT DU |
| Парткод: | -302K329220 |
| Деталь: | PARTS GEAR DU Z27L SP |
| Парткод: | -302K394400 |
| Деталь: | PULLEY DU 26 |
| Парткод: | -302K329280 |
| Деталь: | PULLEY DU 26 B |
| Парткод: | -302K029030 |
| Деталь: | STOPPER 6 |
| Парткод: | -2BC06910 |
| Деталь: | BELT FEED |
| Парткод: | -302MV07110 |
| Деталь: | BELT S2M-Z108 |
| Парткод: | -302KV29090 |
| Деталь: | BELT S2M 230 |
| Парткод: | -303J131270 |
| Деталь: | PARTS ROLLER DU SP |
| Парткод: | -302K394250 |
| Деталь: | PARTS ROLLER DU B SP |
| Парткод: | -302K094390 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | -5MVX111DN007 |
| Деталь: | BUSH DU |
| Парткод: | -302K329270 |
| Деталь: | SPONGE RIGHT COVER |
| Парткод: | -302K029100 |
| Деталь: | JOINT JUNCTION HOOK |
| Парткод: | -302K304571 |
| Деталь: | WIRE EARTH DU B |
| Парткод: | -302K029070 |
| Деталь: | WIRE EARTH DU A |
| Парткод: | -302K029060 |
| Деталь: | COVER RIGHT MIDDLE |
| Парткод: | -302MV04271 |
| Деталь: | LABEL COVER CAUTION |
| Парткод: | -302MV34250 |
| Деталь: | LABEL BYPASS CAUTION |
| Парткод: | -302MV34260 |
| Деталь: | HOOK RIGHT COVER |
| Парткод: | -302K304520 |
| Деталь: | COVER RIGHT HOOK |
| Парткод: | -302MV04300 |
| Деталь: | NUT FUSER A /FS-1800/3800 A4 |
| Парткод: | -5MMS111SL002 |
| Деталь: | STRAP RIGHT COVER |
| Парткод: | -302K304591 |
| Деталь: | LABEL HIGH TEMP |
| Парткод: | -302MV34400 |
| Деталь: | GUIDE EXIT RIGHT |
| Парткод: | -302K029050 |
| Деталь: | SPONGE GUIDE |
| Парткод: | -302K029090 |
| Деталь: | PULLEY DU |
| Парткод: | -302K329020 |
| Деталь: | SPRING DU FEED |
| Парткод: | -302K029080 |
| Деталь: | LABEL COVER CAUTION 9NATIONS |
| Парткод: | -302MV34410 |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | WASHER M3X10X0.8T |
| Парткод: | 7BC00030A080H01 |
| Деталь: | PARTS COVER RIGHT ASSY SP |
| Парткод: | 302MV94450 |
| Деталь: | PARTS HVU1 SP |
| Парткод: | 302K094260 |
| Цена: | 11 600 ₽ |
| Деталь: | HOLDER RFID |
| Парткод: | 302K002B00 |
| Деталь: | PARTS PWB RFID ASSY SP |
| Парткод: | 302K094200 |
| Деталь: | HOLDER PWB MIDDLE |
| Парткод: | 302K002551 |
| Деталь: | PARTS PWB TRANSFER CONNECT ASSY SP |
| Парткод: | 302K094190 |
| Деталь: | WIRE ENGINE2 - TC CONNECT |
| Парткод: | 302K046350 |
| Деталь: | WIRE WT SENS 1 |
| Парткод: | 302K046400 |
| Деталь: | WIRE HUMIT 1 |
| Парткод: | 302NP46270 |
| Деталь: | WIRE HIGH VOL1 |
| Парткод: | 302NP46230 |
| Деталь: | SHIELD HI VOLTAGE TC1 |
| Парткод: | 302K039050 |
| Деталь: | BRACKET HV |
| Парткод: | 302K039070 |
| Деталь: | SPRING CONTACT TC1 |
| Парткод: | 302K039150 |
| Деталь: | PARTS HVU2 SP |
| Парткод: | 302K094270 |
| Деталь: | WIRE ENGINE MAIN-LSU CONNECT 1 |
| Парткод: | 302NP46280 |
| Деталь: | PARTS PWB ENGINE ASSY SP |
| Парткод: | 302NP94100 |
| Деталь: | WIRE SUB PWB |
| Парткод: | 302K046090 |
| Деталь: | WIRE EXIT UNIT1 |
| Парткод: | 302NP46070 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610010++H01 |
| Деталь: | WIRE RELAY |
| Парткод: | 302K046640 |
| Деталь: | SHIELD PWB IH |
| Парткод: | -302K039030 |
| Деталь: | ACCESS.SPACER |
| Парткод: | -7YZM510018++H01 |
| Деталь: | COVER PWB IH |
| Парткод: | -302NP39040 |
| Деталь: | SHIELD GASKET |
| Парткод: | -7ZGSSTG34070H01 |
| Деталь: | WIRE LVU-IH PRIMARY |
| Парткод: | 302NP46350 |
| Деталь: | WIRE ENGINE-IH |
| Парткод: | 302K046620 |
| Деталь: | WIRE OPTION CONNECT |
| Парткод: | 302NP46170 |
| Деталь: | PARTS FAN MOTOR SP |
| Парткод: | 302K094300 |
| Деталь: | WIRE FFC ENGINE-MAIN SIG |
| Парткод: | 302NP46010 |
| Деталь: | WIRE ENGINE POWER1 |
| Парткод: | 302NP46030 |
| Деталь: | WIRE FEED UNIT PI 1 |
| Парткод: | 302K046030 |
| Деталь: | WIRE FEED UNIT 1 |
| Парткод: | 302K046010 |
| Деталь: | WIRE MPF SIZE 1 |
| Парткод: | 302MV46430 |
| Деталь: | WIRE FFC ENGINE 1-2 SIG |
| Парткод: | 302NP46020 |
| Деталь: | PARTS PWB OPTION CONNECT ASSY SP |
| Парткод: | 302NP94130 |
| Деталь: | FERRITE CORE |
| Парткод: | 7YBER0R0E001H01 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | +BIND T.T S SCREW 3X30 SR |
| Парткод: | 7BB700330H |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | PARTS PWB IH 200 ASSY SP |
| Парткод: | 302MV94420 |
| Деталь: | PARTS PWB IH 100 ASSY SP |
| Парткод: | 302MV94410 |
| Деталь: | SPRING HV SLEEVE Y |
| Парткод: | 302K039280 |
| Деталь: | SPRING HV MAG Y |
| Парткод: | 302K039240 |
| Деталь: | SPRING HV MAIN Y |
| Парткод: | 302K039200 |
| Деталь: | SPRING HV SLEEVE C |
| Парткод: | 302K039270 |
| Деталь: | SPRING HV MAG C |
| Парткод: | 302K039230 |
| Деталь: | SPRING HV MAIN C |
| Парткод: | 302K039190 |
| Деталь: | SPRING HV SLEEVE M |
| Парткод: | 302K039260 |
| Деталь: | SPRING HV MAG M |
| Парткод: | 302K039220 |
| Деталь: | SPRING HV MAIN M |
| Парткод: | 302K039180 |
| Деталь: | SPRING HV SLEEVE BK |
| Парткод: | 302K039250 |
| Деталь: | SPRING HV MAG BK |
| Парткод: | 302K039210 |
| Деталь: | SPRING HV MAIN BK |
| Парткод: | 302K039170 |
| Деталь: | SPRING HV TRANSFER |
| Парткод: | 302K039290 |
| Деталь: | SPRING HV SEPARATION |
| Парткод: | 302K039300 |
| Деталь: | SPRING DRUM PWB |
| Парткод: | 302K039160 |
| Деталь: | LID TERMINAL |
| Парткод: | 302K039140 |
| Деталь: | PIN TONER SUPPLY |
| Парткод: | 302K015250 |
| Деталь: | GEAR IDLE Z22S |
| Парткод: | 302K015230 |
| Деталь: | GEAR JOINT Z26S |
| Парткод: | 302K015240 |
| Деталь: | COVER GEAR SUPPLY |
| Парткод: | 302K015460 |
| Деталь: | PARTS PWB DRUM DLP CONNECT ASSY SP |
| Парткод: | 302NP94190 |
| Деталь: | RAIL MIDDLE TRANSFER R |
| Парткод: | 302K002601 |
| Деталь: | SLIDER MIDDLE TRANSFER R |
| Парткод: | 302K002940 |
| Деталь: | SPRING MIDDLE TRANSFER SLIDER |
| Парткод: | 302K002960 |
| Деталь: | LABEL MIDDLE TRANSFER |
| Парткод: | 302MV34080 |
| Деталь: | WORK-PLATE MIDDLE TRANSFER COUPLING |
| Парткод: | 302K002950 |
| Деталь: | SPRING MIDDLE TRANSFER COUPLING |
| Парткод: | 302K002970 |
| Деталь: | PARTS TONER SUPPLY ASSY SP |
| Парткод: | 302K094050 |
| Деталь: | SEAL TONER SUPPLY A |
| Парткод: | 302K015350 |
| Деталь: | BASE CONTAINER |
| Парткод: | 302K002050 |
| Деталь: | SEAL TONER |
| Парткод: | 302K002D51 |
| Деталь: | RAIL CONTAINER L |
| Парткод: | 302K002A40 |
| Деталь: | DAMPER CONTAINER |
| Парткод: | 302K002A60 |
| Деталь: | SPRING DAMPER CONT |
| Парткод: | 302K002B70 |
| Деталь: | RAIL CONTAINER R |
| Парткод: | 302K002A50 |
| Деталь: | SHUTTER TONER SUPPLY A |
| Парткод: | 302K015200 |
| Деталь: | SEAL SHUTTER SUPPLY |
| Парткод: | 302K015340 |
| Деталь: | BALL TN FEED |
| Парткод: | 302K015500 |
| Деталь: | SPRING TN FEED |
| Парткод: | 302K015490 |
| Деталь: | SPRING SHUTTER SUPPLY A |
| Парткод: | 302K015320 |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | BASE MIDDLE DRIVE R |
| Парткод: | -302K031040 |
| Деталь: | SPRING MAIN DRIVE B |
| Парткод: | -302K031420 |
| Деталь: | PLATE MIDDLE DRIVE |
| Парткод: | -302K031070 |
| Деталь: | PARTS MOTOR-BL W20 SP |
| Парткод: | -302K994321 |
| Деталь: | PLATE MOTOR MIDDLE |
| Парткод: | -302K031100 |
| Деталь: | BUSH 6 EW |
| Парткод: | -302H024370 |
| Деталь: | POLYSLIDER WASHER |
| Парткод: | -2FT18370 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | -5MVX111DN003 |
| Деталь: | GUIDE WIRE MIDDLE DRIVE |
| Парткод: | -302K031470 |
| Деталь: | PARTS GEAR MIDDLE TRANS Z89R SP |
| Парткод: | -302MV94390 |
| Деталь: | ONE WAY CLUTCH /A-49 MPFz A4 |
| Парткод: | -5AAVCLTCH018 |
| Деталь: | PARTS GEAR MIDDLE TRANS Z90R-Z37L SP |
| Парткод: | -302MV94400 |
| Деталь: | GEAR FUSER Z74R-Z24 |
| Парткод: | -302K031260 |
| Деталь: | SPRING FUSER |
| Парткод: | -302K031610 |
| Деталь: | GEAR FUSER Z45 |
| Парткод: | -302K031270 |
| Деталь: | GEAR FUSER Z24 |
| Парткод: | -302K031600 |
| Деталь: | GEAR FUSER Z25 |
| Парткод: | -302K031280 |
| Деталь: | GEAR DLP Z45R |
| Парткод: | -302K031210 |
| Деталь: | GEAR DLP Z87R-Z66L |
| Парткод: | -302K031150 |
| Деталь: | GEAR DLP Z53R |
| Парткод: | -302K031200 |
| Деталь: | BASE MIDDLE DRIVE F |
| Парткод: | -302K031030 |
| Деталь: | PARTS DRIVE MIDDLE TRANS SP |
| Парткод: | -302K094640 |
| Деталь: | WIRE BELT-FUSER MOT |
| Парткод: | 302K046180 |
| Деталь: | HOLDER TONER DRIVE B |
| Парткод: | 302K015022 |
| Деталь: | PARTS DC MOTOR SP |
| Парткод: | 302NP94220 |
| Деталь: | CONNECTOR 292254-2 |
| Парткод: | 7YCC02B1003+H01 |
| Деталь: | SHEET HOLDER TONER DRIVE |
| Парткод: | 302K015540 |
| Деталь: | PARTS DC MOTOR SP |
| Парткод: | 302K094100 |
| Цена: | 6 300 ₽ |
| Деталь: | WIRE TONER SUPPLY MOT |
| Парткод: | 302K046130 |
| Деталь: | GEAR Z50S |
| Парткод: | 302K015040 |
| Деталь: | SPRING JOINT CONTAINER |
| Парткод: | 302K015270 |
| Деталь: | GEAR Z20S-Z26L |
| Парткод: | 302K015030 |
| Деталь: | HOLDER TONER DRIVE A |
| Парткод: | 302K015010 |
| Деталь: | LID WIRE GUIDE |
| Парткод: | 303LT02020 |
| Деталь: | + BIND M SCREW 3X4 |
| Парткод: | 7BB000304H |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | DR-895B |
| Парткод: | 302K093131 |
| Деталь: | FK-8507 IH |
| Парткод: | 302LC93090 |
| Деталь: | FK-8506 IH |
| Парткод: | 302LC93080 |
| Деталь: | FK-8325 |
| Парткод: | 302NP93080 |
| Деталь: | STOPPER BYPASS TABLE |
| Парткод: | 2FB07330 |
| Деталь: | SPRING FRONT COVER L |
| Парткод: | 302MV04320 |
| Деталь: | HOLDER SWITCH |
| Парткод: | 302NP04200 |
| Деталь: | EMBLEM |
| Парткод: | 302LC04272 |
| Деталь: | SHEET EMBLEM |
| Парткод: | 302NP34010 |
| Деталь: | SHEET COVER FRONT |
| Парткод: | 302NP34040 |
| Деталь: | COVER INNER BASE |
| Парткод: | 302K302260 |
| Деталь: | PARTS COVER FRONT ASSY 25 SP |
| Парткод: | 302NP940 |
| Деталь: | COVER SW FEED |
| Парткод: | 302MV07080 |
| Деталь: | GUIDE COVER INNER |
| Парткод: | -302MV07051 |
| Деталь: | COVER RIGHT LOW |
| Парткод: | -302NL04340 |
| Деталь: | HOLDER SPRING |
| Парткод: | -302MV07070 |
| Деталь: | Cover Handle |
| Парткод: | -302NL06060 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | -2FM04150 |
| Деталь: | SPRING FEED LOW |
| Парткод: | -303NN24180 |
| Деталь: | SHAFT FEED B |
| Парткод: | -302BG06152 |
| Деталь: | PULLEY 15 DUPLEX |
| Парткод: | -3HY07120 |
| Деталь: | SPRING LID |
| Парткод: | -302FZ20021 |
| Деталь: | HOOK FEED LOW |
| Парткод: | -302K906670 |
| Деталь: | SHAFT FEED LOW HOOK |
| Парткод: | -302NL06070 |
| Деталь: | HANDLE FEED LOW |
| Парткод: | -303PC06060 |
| Деталь: | HOLDER HOOK F |
| Парткод: | 302NL06040 |
| Деталь: | HOLDER HOOK R |
| Парткод: | 302NL06050 |
| Деталь: | BAND B |
| Парткод: | 2BG06480 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000001+H01 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | SPRING EARTH SW |
| Парткод: | 303NN24250 |
| Деталь: | WIRE RIGHT COVER SW |
| Парткод: | 302MV46520 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | + BIND T.T P SCREW 4X10 |
| Парткод: | 7BB200410H |
| Деталь: | +BIND M SCREW 3X6 R |
| Парткод: | 7BB600306H |
| Деталь: | PARTS COVER RIGHT LOW ASSY SP |
| Парткод: | 302NP94230 |
| Деталь: | MC-8325 |
| Парткод: | -302NP93020 |
| Деталь: | DK-8325 |
| Парткод: | 302NP93030 |
| Деталь: | PLATE NUMBER |
| Парткод: | 2BL04310 |
| Деталь: | PLATE NUMBER 2 |
| Парткод: | 2BL04370 |
| Деталь: | SHEET CASSETTE C |
| Парткод: | 302MV34300 |
| Деталь: | SHEET CASSETTE I |
| Парткод: | 302MV34430 |
| Деталь: | LABEL OPERATION L |
| Парткод: | -302MV34330 |
| Деталь: | EMBLEM CASSETTE |
| Парткод: | -302NL09070 |
| Деталь: | COVER CASSETTE |
| Парткод: | -302NL09050 |
| Деталь: | HANDLE CASSETTE |
| Парткод: | -302NL09080 |
| Деталь: | CASSETTE |
| Парткод: | -302NL09010 |
| Деталь: | LABEL OPERATION S |
| Парткод: | -302MV34340 |
| Деталь: | LABEL CASSETTE SIZE A |
| Парткод: | -302MV34310 |
| Деталь: | LABEL CASSETTE SIZE B |
| Парткод: | -302MV34360 |
| Деталь: | LABEL OPERATION CURSOR |
| Парткод: | -302MV34320 |
| Деталь: | PLATE SIDE SWITCH |
| Парткод: | -302MV09050 |
| Деталь: | SPRING SIDE SWITCH |
| Парткод: | -302K309220 |
| Деталь: | ARM SIZE DETECTION |
| Парткод: | -302MV09040 |
| Деталь: | CURSOR END |
| Парткод: | -302K309270 |
| Деталь: | SPRING CURSOR R |
| Парткод: | -2C907360 |
| Деталь: | SLIDER CURSOR END |
| Парткод: | -302K309141 |
| Деталь: | SPRING SIZE SET |
| Парткод: | -302K309360 |
| Деталь: | STOPPER SIZE SET |
| Парткод: | -302K309350 |
| Деталь: | CURSOR CASSETTE REAR |
| Парткод: | -302MV09080 |
| Деталь: | LEVER CURSOR SET |
| Парткод: | -302K309190 |
| Деталь: | SPRING CURSOR SET |
| Парткод: | -302K309370 |
| Деталь: | LABEL PAPER LIMIT |
| Парткод: | -302MV34370 |
| Деталь: | CURSOR CASSETTE FRONT |
| Парткод: | -302MV09090 |
| Деталь: | LEVER RELEASE CURSOR F |
| Парткод: | -302K309200 |
| Деталь: | SPRING RELEASE CURSOR F |
| Парткод: | -302K309210 |
| Деталь: | SPRING SIZE SET F |
| Парткод: | -302K309380 |
| Деталь: | SIZE FIX |
| Парткод: | -302HN09240 |
| Деталь: | PARTS GEAR Z18 SP |
| Парткод: | -302K394380 |
| Деталь: | SHAFT DRIVE LIFT |
| Парткод: | -302K309180 |
| Деталь: | PLATE LIFT BASE CASSETTE |
| Парткод: | -302K309170 |
| Деталь: | STOPPER 6 |
| Парткод: | -2BC06910 |
| Деталь: | SPRING CASSETTE LIFT EARTH |
| Парткод: | -302K309300 |
| Деталь: | BASE CASSETTE |
| Парткод: | -302MV09021 |
| Деталь: | PAD CASSETTE |
| Парткод: | -2C907140 |
| Деталь: | LABEL PAPER SET |
| Парткод: | -302MV34350 |
| Деталь: | LIFT BASE CASSETTE SUB |
| Парткод: | -302K309150 |
| Деталь: | SPRING LEVER LIFT CASSETTE SUB |
| Парткод: | -302K309160 |
| Деталь: | PLATE CASSETTE LEFT |
| Парткод: | -302NL09090 |
| Деталь: | PLATE CASSETTE RIGHT |
| Парткод: | -302NL09100 |
| Деталь: | PULLEY MPT BYPASS |
| Парткод: | -302FZ07020 |
| Деталь: | PULLEY,CASSETTE RAIL |
| Парткод: | -302FG07020 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | -5MVX111DN003 |
| Деталь: | +TP-FLAT T.T P SCREW 4X10 |
| Парткод: | 7BB202410H |
| Деталь: | SPRING PIN |
| Парткод: | 5MBP2514WXSP |
| Деталь: | +FLAT HEAD T.T P SCREW 3X8 |
| Парткод: | 7BB203308H |
| Деталь: | CT-8325 |
| Парткод: | 302NP93010 |
| Деталь: | Электромагнитная муфта |
| Парткод: | 302KV44041 |
| Цена: | 900 ₽ |
| Деталь: | Жидкокристаллический дисплей панели управления |
| Парткод: | 302N494090 |
| Деталь: | COVER INNER FRONT LOWER |
| Парткод: | 302MV04230 |
| Деталь: | LID CONTROLLER |
| Парткод: | 302NL04200 |
| Деталь: | COVER EXIT REAR |
| Парткод: | 302NP04040 |
| Деталь: | COVER TRAY |
| Парткод: | 302NP04030 |
| Деталь: | STOPPER PAPER |
| Парткод: | 302H004560 |
| Деталь: | COVER TRAY LEFT |
| Парткод: | 302NP04180 |
| Деталь: | COVER LEFT TOP |
| Парткод: | 302NP04110 |
| Деталь: | LID COVER LEFT |
| Парткод: | 302FZ04240 |
| Деталь: | COVER RIGHT TOP |
| Парткод: | 302NL04090 |
| Деталь: | COVER LEFT LOW |
| Парткод: | 302NP04100 |
| Деталь: | FOOT |
| Парткод: | 302MV02190 |
| Деталь: | COVER FRONT TOP |
| Парткод: | 302MV04020 |
| Деталь: | LABEL DEHUMIDIFIER SWITCH |
| Парткод: | -302NL34090 |
| Деталь: | COVER MAIN SW |
| Парткод: | -302H704170 |
| Деталь: | LABEL SW CAUTION EN |
| Парткод: | -302LC34620 |
| Деталь: | STOPPER PAPER C |
| Парткод: | -302K317820 |
| Деталь: | LID DF CONNECTOR |
| Парткод: | 302MN04100 |
| Деталь: | LID AK |
| Парткод: | 302NL04250 |
| Деталь: | LABEL SW CAUTION SET A |
| Парткод: | 302LC34630 |
| Деталь: | +TP-FLAT T.T S SCREW 3X8 SR(BLACK) |
| Парткод: | 7BB782308H |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | PARTS COVER REAR ASSY E SP |
| Парткод: | 302NP94010 |
| Деталь: | PARTS COVER RIGHT REAR ASSY EN SP |
| Парткод: | 302NP94050 |
| Деталь: | PARTS TRAY EJECT ASSY SP |
| Парткод: | 302MV94550 |
| Деталь: | WIRE BRIDGE 1 |
| Парткод: | 302NP46140 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | MOUNT ENGINE PWB B |
| Парткод: | 302NP39100 |
| Деталь: | FRAME REAR UPPER |
| Парткод: | 302K002151 |
| Деталь: | SLIDER ASSY |
| Парткод: | 302K026090 |
| Деталь: | SPRING EARTH EXIT |
| Парткод: | 302K002671 |
| Деталь: | FRAME FRONT UPPER |
| Парткод: | 302K002141 |
| Деталь: | ADJUSTER FUSER |
| Парткод: | 302K325350 |
| Деталь: | MOUNT FUSER FRONT |
| Парткод: | 302K002290 |
| Деталь: | COVER FUSER MOUNT REAR |
| Парткод: | 302K026030 |
| Деталь: | WIRE FUSER UNIT 1 |
| Парткод: | 302NP46260 |
| Деталь: | HOLDER DRAWER FUSER |
| Парткод: | 302K002660 |
| Деталь: | LEVER FUSER RELEASE FRONT |
| Парткод: | 302MV26010 |
| Деталь: | COVER FUSER MOUNT FRONT |
| Парткод: | 302K026020 |
| Деталь: | SHAFT RAIL |
| Парткод: | 302K026130 |
| Деталь: | GEAR IDLE Z20S |
| Парткод: | 302K026120 |
| Деталь: | SPRING EARTH FUSER RAIL |
| Парткод: | 302K026080 |
| Деталь: | LEVER FUSER RELEASE REAR |
| Парткод: | 302MV26020 |
| Деталь: | SPRING FUSER LOCK LEVER |
| Парткод: | 302K026060 |
| Деталь: | SPRING FUSER LOCK LEVER R |
| Парткод: | 302K026180 |
| Деталь: | LABEL H2 |
| Парткод: | 302MV34170 |
| Деталь: | LABEL PUSH |
| Парткод: | 302MV34240 |
| Деталь: | SHEET RAIL |
| Парткод: | 302K026190 |
| Деталь: | LEVER TRANSFER SHIELD |
| Парткод: | 302K026150 |
| Деталь: | BASE FUSER MOUNT |
| Парткод: | 302K026010 |
| Деталь: | BRACKET DRAWER |
| Парткод: | 302NL02080 |
| Деталь: | WIRE RFID PWB |
| Парткод: | 302NP46240 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | +TP-FLAT T.T P SCREW 3X8 |
| Парткод: | 7BB202308H |
| Деталь: | FILM LCD WIRE |
| Парткод: | -302N405210 |
| Деталь: | CUSHION LCD |
| Парткод: | -302H705610 |
| Деталь: | SPONGE LCD B |
| Парткод: | -302K505280 |
| Деталь: | PARTS PWB OPERATION ASSY SP |
| Парткод: | -302N494180 |
| Деталь: | KEY MENU |
| Парткод: | -302N405080 |
| Деталь: | PARTS LCD OPERATION SP |
| Парткод: | -302N494090 |
| Деталь: | PARTS PWB PANEL MAIN ASSY SP |
| Парткод: | -302N494150 |
| Деталь: | COVER OPERATION A |
| Парткод: | -302NL05010 |
| Деталь: | KEY 10 |
| Парткод: | -302LC05050 |
| Деталь: | KEY COLOR |
| Парткод: | -302N405060 |
| Деталь: | KEY FUNCTION |
| Парткод: | -302N405070 |
| Деталь: | SHEET WIRE CONV E |
| Парткод: | -302H722690 |
| Деталь: | KEY START |
| Парткод: | -302LC05090 |
| Деталь: | KEY STOP |
| Парткод: | -302LC05100 |
| Деталь: | KEY RESET |
| Парткод: | -302LC05110 |
| Деталь: | KEY POWER |
| Парткод: | -302N405090 |
| Деталь: | LID OPERATION SHEET A |
| Парткод: | -302N405140 |
| Деталь: | LID OPERATION SHEET B |
| Парткод: | -302N405150 |
| Деталь: | PARTS TABLET OPERATION SP |
| Парткод: | -302N494100 |
| Деталь: | SHEET COLOR |
| Парткод: | -302N405520 |
| Деталь: | KEY HOME |
| Парткод: | -302N405100 |
| Деталь: | KEY DISPLAY |
| Парткод: | -302N405110 |
| Деталь: | KEY RIGHT SIDE |
| Парткод: | -302N405120 |
| Деталь: | HOLDER LCD |
| Парткод: | -302LC05270 |
| Деталь: | PARTS SPEAKER SP |
| Парткод: | -302LC94370 |
| Деталь: | WIRE FFC KEY PWB |
| Парткод: | -302N446050 |
| Деталь: | LENS LED |
| Парткод: | -302N405200 |
| Деталь: | MOUNT MAIN PWB |
| Парткод: | -302NL05030 |
| Деталь: | GUIDE WIRE OPERATION |
| Парткод: | -302NL05040 |
| Деталь: | WIRE PANEL JOINT |
| Парткод: | -302NP46450 |
| Деталь: | WIRE PANEL DATA |
| Парткод: | -302NP46390 |
| Деталь: | HOLDER WIRE D |
| Парткод: | -303LL02330 |
| Деталь: | FILM FFC |
| Парткод: | -302LC05420 |
| Деталь: | WIRE USB HOST |
| Парткод: | 302NP46400 |
| Деталь: | SPRING USB HOLD |
| Парткод: | 302K905900 |
| Деталь: | COVER OPERATION B |
| Парткод: | 302NL05020 |
| Деталь: | PANEL OPERATION |
| Парткод: | 302N405130 |
| Деталь: | SHEET OPERATION EN |
| Парткод: | 302N405510 |
| Деталь: | SHEET OPERATION KDA EN |
| Парткод: | 302N405630 |
| Деталь: | MOUNT USB |
| Парткод: | 302MV05050 |
| Деталь: | MOUNT OPERATION |
| Парткод: | 302NL05050 |
| Деталь: | PLATE EARTH ISU |
| Парткод: | 302K302A50 |
| Деталь: | WIRE MAIN-OPERATION |
| Парткод: | 302NP46380 |
| Деталь: | FILM COVER LOW |
| Парткод: | 302MV05090 |
| Деталь: | CLAMP,EMT-3N(TAKEUCHI) |
| Парткод: | M7005010 |
| Деталь: | +TP-FLAT T.T S SCREW 3X8 SR(BLACK) |
| Парткод: | 7BB782308H |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | + BIND M SCREW 3X6 |
| Парткод: | 7BB000306H |
| Деталь: | PARTS OPERATION UNIT SP |
| Парткод: | 302NP94070 |
| Деталь: | PARTS PRIMARY FEED ASSY SP |
| Парткод: | 302MV94061 |
| Деталь: | ELA UNIT-TRANSFER |
| Парткод: | TR-8315B |
| Цена: | 4 200 ₽ |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325C |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325K |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325M |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325Y |
| Деталь: | Formatter, exchange, HP Color LaserJet 3000dn and 3000dtn Series only (256 MB) |
| Парткод: | 302NP94151 |
| Цена: | 81 100 ₽ |
| Деталь: | LASER SCANNER ASSY |
| Парткод: | LK-8325 |
| Цена: | 22 600 ₽ |
| Деталь: | Правая часть узла термозакрепления, в сборе (220В) |
| Парткод: | FK-8325 |
| Цена: | 28 900 ₽ |
| Деталь: | Левая часть узла термозакрепления, в сборе (220В) |
| Парткод: | FK-8507 |
| Цена: | 15 900 ₽ |
| Деталь: | Комплект для технического обслуживания |
| Парткод: | MK-8325B |
| Деталь: | Комплект для технического обслуживания |
| Парткод: | MK-8325A |
| Деталь: | SHEET GUIDE FEED |
| Парткод: | 302K002D70 |
| Деталь: | SENSOR OPT |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000001+H01 |
| Деталь: | PLATE SIZE DETECTION |
| Парткод: | 302K309410 |
| Деталь: | STAY FRONT RIGHT |
| Парткод: | 302MV02200 |
| Деталь: | RAIL MIDDLE TRANSFER F |
| Парткод: | 302K002531 |
| Деталь: | LABEL MIDDLE TRANSFER |
| Парткод: | 302MV34080 |
| Деталь: | HANDLE |
| Парткод: | 302JF02160 |
| Деталь: | SEAL HANDLE |
| Парткод: | 302FZ03110 |
| Деталь: | CAP HANDLE |
| Парткод: | 302FZ02580 |
| Деталь: | PIN FRONT HANDLE |
| Парткод: | 302MV02240 |
| Деталь: | STOPPER 4 |
| Парткод: | 302FZ25740 |
| Деталь: | HEATER DEHUMIDIFIER 240 |
| Парткод: | 302K302440 |
| Деталь: | HEATER DEHUMIDIFIER 120 |
| Парткод: | 302K302430 |
| Деталь: | LABEL HIGH TEMPERATURE CAUTION |
| Парткод: | 302KP34220 |
| Деталь: | CAP DECK PIN |
| Парткод: | 302K302920 |
| Деталь: | GUIDE WIRE MAIN SW |
| Парткод: | 302NL39060 |
| Деталь: | MOUNT DECK PI |
| Парткод: | 302K302840 |
| Деталь: | MOUNT DECK DRAWER |
| Парткод: | 302K302910 |
| Деталь: | WIRE PF DRAWER 200 |
| Парткод: | 302K346660 |
| Деталь: | WIRE PF DRAWER |
| Парткод: | 302K346470 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610009++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610010++H01 |
| Деталь: | GUIDE WIRE LVU B |
| Парткод: | 302MV39270 |
| Деталь: | STAY POWER |
| Парткод: | 302MV39230 |
| Деталь: | SPRING MAIN DRIVE B |
| Парткод: | 302K031420 |
| Деталь: | SHAFT HANDLE |
| Парткод: | 302MV02220 |
| Деталь: | MOUNT REAR HANDLE |
| Парткод: | 302MV02231 |
| Деталь: | DUCT CORD |
| Парткод: | 302K002650 |
| Деталь: | WIRE PAPER EMPTY/BOTTOM UP |
| Парткод: | 302K046290 |
| Деталь: | WIRE PF SIG |
| Парткод: | 302MV46320 |
| Деталь: | WIRE CASSETTE2 PI |
| Парткод: | 302NP46080 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510006++H01 |
| Деталь: | WIRE FEED UNIT PI2 |
| Парткод: | 302MV46560 |
| Деталь: | SLIDER MIDDLE TRANSFER F |
| Парткод: | 302K002930 |
| Деталь: | SPRING MIDDLE TRANSFER SLIDER |
| Парткод: | 302K002960 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210002++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610011++H01 |
| Деталь: | SPONGE LOWER RIGHT SP |
| Парткод: | 302LF33B10 |
| Деталь: | PARTS AC CORD EU SP |
| Парткод: | 302AR94050 |
| Деталь: | AC CORD ASSY AS |
| Парткод: | 7AAACCAS+10H001 |
| Деталь: | POWER CORD(120) |
| Парткод: | 3019527401 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | + BIND T.T S SCREW 4X6 |
| Парткод: | 7BB100406H |
| Деталь: | MOUNT SCANNER REAR |
| Парткод: | 302NP02110 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210003++H01 |
| Деталь: | HOLDER CORD RIGHT |
| Парткод: | 302MV02341 |
| Деталь: | SW. SEESAW |
| Парткод: | 7SC020403+++H01 |
| Деталь: | MOUNT SCANNER RIGHT |
| Парткод: | 302MV02092 |
| Деталь: | MOUNT OPTION |
| Парткод: | 302MV02131 |
| Деталь: | MOUNT SCANNER FRONT |
| Парткод: | 302NL02240 |
| Деталь: | COVER EXIT FRONT TOP |
| Парткод: | 302MV04290 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | SHEET SCANNER FRONT |
| Парткод: | 302NL02360 |
| Деталь: | MOUNT RIGHT INTERLOCK |
| Парткод: | 302K002210 |
| Деталь: | SW.MICRO |
| Парткод: | 7SM010101+++H01 |
| Деталь: | SPRING BYPASSFFED |
| Парткод: | 302H008140 |
| Деталь: | PIN FUSER COVER |
| Парткод: | 2FB20860 |
| Деталь: | WIRE MAIN SWITCH |
| Парткод: | 302NP46120 |
| Деталь: | WIRE AC CASSETTE SW |
| Парткод: | 302NP46110 |
| Деталь: | COVER EXIT HARNESS |
| Парткод: | 302K002A00 |
| Деталь: | PUSH SWITCH 03 SN /SW-192 N |
| Парткод: | 5ESP03090001+01 |
| Деталь: | MOUNT INLET (CHN) |
| Парткод: | 302MV39380 |
| Деталь: | WIRE DF |
| Парткод: | 302NP46330 |
| Деталь: | SPACER,SFS-2.6S-B1WM(JST) |
| Парткод: | M0208010 |
| Деталь: | SW. SEESAW |
| Парткод: | 7SC010105+++H01 |
| Деталь: | LID VENDOR |
| Парткод: | 302FB26290 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210005++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610009++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610010++H01 |
| Деталь: | WIRE CASSETTE SIZE SW |
| Парткод: | 302K046280 |
| Деталь: | WIRE INLET |
| Парткод: | 302NP46100 |
| Деталь: | STAY SHIELD POWER |
| Парткод: | 302K002750 |
| Деталь: | WIRE MPF SIZE 2 |
| Парткод: | 302MV46440 |
| Деталь: | MOUNT SCANNER ADJUST |
| Парткод: | 302K302210 |
| Деталь: | MOUNT MAIN SW |
| Парткод: | 302NP39050 |
| Деталь: | LID DEHUMIDIFIER SW |
| Парткод: | 302K302890 |
| Деталь: | SPACER SCANNER ADJUST |
| Парткод: | 302K302200 |
| Деталь: | COVER WIRE EJECT |
| Парткод: | 303JY28390 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | +TP-FLAT T.T S SCREW 3X8 SR |
| Парткод: | 7BB702308H |
| Деталь: | PARTS MOTOR-BL W30 SP |
| Парткод: | -302K994331 |
| Деталь: | PLATE MOTOR DLP |
| Парткод: | -302K031090 |
| Деталь: | PARTS MOTOR-BL W20 DRUM SP |
| Парткод: | -302LC94301 |
| Деталь: | PLATE MOTOR MAIN |
| Парткод: | -302K031080 |
| Деталь: | BASE MAIN DRIVE R |
| Парткод: | -302K031020 |
| Деталь: | SPRING MAIN DRIVE B |
| Парткод: | -302K031420 |
| Деталь: | BUSH 6 EW |
| Парткод: | -302H024370 |
| Деталь: | SHAFT DLP |
| Парткод: | -302K031350 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | -5MVX111DN003 |
| Деталь: | PARTS CLUTCH 50 Z45L SP |
| Парткод: | -302K094320 |
| Деталь: | HOLDER CLUTCH |
| Парткод: | -302K031450 |
| Деталь: | PLATE MAIN DRIVE R |
| Парткод: | -302K031060 |
| Деталь: | PIN DRIVE B |
| Парткод: | -302HN31680 |
| Деталь: | PIN DRIVE A |
| Парткод: | -302HN31670 |
| Деталь: | PIN DRIVE MT |
| Парткод: | -302HN31640 |
| Деталь: | PARTS GEAR DRUM Z180L SP |
| Парткод: | -302MV94360 |
| Деталь: | PARTS GEAR DRUM Z100R SP |
| Парткод: | -302MV94370 |
| Деталь: | PARTS GEAR DRUM Z120L SP |
| Парткод: | -302MV94380 |
| Деталь: | SPRING MAIN DRIVE A |
| Парткод: | -302K031410 |
| Деталь: | COLLAR MIDDLE CLN A |
| Парткод: | -302K031380 |
| Деталь: | GEAR CLN Z30R-Z32 |
| Парткод: | -302K031290 |
| Деталь: | PULLEY MIDDLE CLN Z30 |
| Парткод: | -302K031330 |
| Деталь: | PULLEY MIDDLE CLN IDLE |
| Парткод: | -302K031340 |
| Деталь: | BASE TENSION R |
| Парткод: | -302K031440 |
| Деталь: | BASE TENSION F |
| Парткод: | -302K031431 |
| Деталь: | BELT S2M Z371 |
| Парткод: | -302KV02A90 |
| Деталь: | BUSH SCREW |
| Парткод: | -302H702590 |
| Деталь: | GEAR MIDDLE CLN Z37R |
| Парткод: | -302K031320 |
| Деталь: | SHAFT MIDDLE CLN |
| Парткод: | -302K031370 |
| Деталь: | GEAR MIDDLE CLN Z27L-Z21L |
| Парткод: | -302K031300 |
| Деталь: | GEAR MIDDLE CLN Z30R |
| Парткод: | -302K031310 |
| Деталь: | PLATE MAIN DRIVE F |
| Парткод: | -302K031050 |
| Деталь: | GEAR DLP Z45R |
| Парткод: | -302K031140 |
| Деталь: | GEAR DLP Z37L |
| Парткод: | -302K031170 |
| Деталь: | GEAR DLP Z31R |
| Парткод: | -302K031180 |
| Деталь: | GEAR DLP Z87R-Z66L |
| Парткод: | -302K031150 |
| Деталь: | GEAR DLP Z53R-Z45R |
| Парткод: | -302K031160 |
| Деталь: | GEAR DLP Z45L |
| Парткод: | -302K031190 |
| Деталь: | BASE MAIN DRIVE F |
| Парткод: | -302K031010 |
| Деталь: | COLLAR MIDDLE CLN B |
| Парткод: | -302K031390 |
| Деталь: | SPRING MIDDLE CLN |
| Парткод: | -302K031480 |
| Деталь: | JOINT SHAFT CASSETTE |
| Парткод: | -302HN31660 |
| Деталь: | SHIELD GASKET |
| Парткод: | -7ZGSSTG47023H01 |
| Деталь: | WIRE DRUM-DLP MOT |
| Парткод: | 302K046140 |
| Деталь: | + BIND M SCREW 3X4 |
| Парткод: | 7BB000304H |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | DR-895A |
| Парткод: | 302K093122 |
| Деталь: | TR-8315A |
| Парткод: | 302MV93070 |
| Деталь: | SENSOR OPT |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | SWITCH RELEASE |
| Парткод: | 302NL17020 |
| Деталь: | MOUNT ISC |
| Парткод: | 302NL17040 |
| Деталь: | GUIDE FFC CCD |
| Парткод: | 302MV17040 |
| Деталь: | SENSOR ORIGINAL |
| Парткод: | 302H044110 |
| Деталь: | WIRE CCD POWER |
| Парткод: | 302MV46600 |
| Деталь: | WIRE ORIGINAL SENSOR |
| Парткод: | 302K946750 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390002++H01 |
| Деталь: | WIRE FFC LED |
| Парткод: | 302MV46630 |
| Деталь: | GUIDE FFC LED C |
| Парткод: | 302K317172 |
| Деталь: | SHEET FFC LED |
| Парткод: | 302K317791 |
| Деталь: | WIRE FFC CCD |
| Парткод: | 302NL46380 |
| Деталь: | FERRITE CORE |
| Парткод: | 7YBFZZ65C001H01 |
| Деталь: | PARTS PWB ISC ASSY SP |
| Парткод: | 302NP94180 |
| Деталь: | MOTOR REVERSE |
| Парткод: | 302HN44100 |
| Деталь: | PARTS GEAR Z18-Z63R SP |
| Парткод: | 302K394370 |
| Деталь: | GEAR Z54 |
| Парткод: | 302K317350 |
| Деталь: | MOUNT DRIVE |
| Парткод: | 302NL17010 |
| Деталь: | WIRE SCANNER MOT |
| Парткод: | 302NP46500 |
| Деталь: | WIRE HP SENSOR |
| Парткод: | 302NP46490 |
| Деталь: | HOLDER SWITCH |
| Парткод: | 302NL17030 |
| Деталь: | WIRE OPEN SENSOR |
| Парткод: | 302NP46480 |
| Деталь: | MOUNT JUNCTION PWB |
| Парткод: | 302NL17070 |
| Деталь: | PARTS ISU |
| Парткод: | 302NP93130 |
| Деталь: | PARTS PWB DP JUNCTION ASSY SP |
| Парткод: | 302NP94160 |
| Деталь: | WIRE DP JUNCTION |
| Парткод: | 302NP46420 |
| Деталь: | FILM FFC CCD |
| Парткод: | 302MV17110 |
| Деталь: | COVER LENS |
| Парткод: | 302MV17030 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZG65TSV+010H01 |
| Деталь: | STOPPER 5 |
| Парткод: | 2BC06980 |
| Деталь: | MOUNT DP |
| Парткод: | 302NL17050 |
| Деталь: | PIN FUSER COVER |
| Парткод: | 2FB20860 |
| Деталь: | PARTS CONTACT-GLASS ASSY(C) SP |
| Парткод: | 302MV94110 |
| Деталь: | PARTS CONTACT-GLASS ASSY(I) SP |
| Парткод: | 302MV94100 |
| Деталь: | FILM FFC CCD B |
| Парткод: | 302MV17130 |
| Деталь: | PARTS PWB SCANNER LED ASSY SP |
| Парткод: | -302NP94170 |
| Деталь: | MOUNT LED |
| Парткод: | -302K317470 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | +PAN M SCREW WITH SW W 3X8 R |
| Парткод: | 7BB606308H |
| Деталь: | PARTS MOUNT LED ASSY SP |
| Парткод: | 302NP93090 |
| Деталь: | PARTS CLEANING REGIST ASSY SP |
| Парткод: | 302MV94030 |
| Деталь: | SPRING RETAINER L |
| Парткод: | 302K002460 |
| Деталь: | COVER INNER FRONT |
| Парткод: | 302NP02040 |
| Деталь: | BKT COVER INNER FRONT |
| Парткод: | 302K002990 |
| Деталь: | COVER INNER DUCT |
| Парткод: | 302K002D30 |
| Деталь: | PIECE CONTAINER K |
| Парткод: | 302K002B10 |
| Деталь: | LABEL BLACK |
| Парткод: | 302K034090 |
| Деталь: | PIECE CONTAINER M |
| Парткод: | 302K002B20 |
| Деталь: | LABEL MAGENTA |
| Парткод: | 302K034100 |
| Деталь: | PIECE CONTAINER C |
| Парткод: | 302K002B30 |
| Деталь: | LABEL CYAN |
| Парткод: | 302K034110 |
| Деталь: | PIECE CONTAINER Y |
| Парткод: | 302K002B40 |
| Деталь: | LABEL YELLOW |
| Парткод: | 302K034120 |
| Деталь: | HOOK LEVER Y |
| Парткод: | 302NP03040 |
| Деталь: | PIECE RAIL BK |
| Парткод: | 302K002830 |
| Деталь: | PIECE RAIL M |
| Парткод: | 302K002840 |
| Деталь: | PIECE RAIL C |
| Парткод: | 302K002850 |
| Деталь: | PIECE RAIL Y |
| Парткод: | 302K002680 |
| Деталь: | PARTS PWB THERMISTOR ASSY SP |
| Парткод: | 302NP94120 |
| Деталь: | WIRE HUMIT 2 |
| Парткод: | 302K046830 |
| Деталь: | LID GUIDE FFC LED |
| Парткод: | 302K317490 |
| Деталь: | HOLDER RETAINER |
| Парткод: | 302K002371 |
| Деталь: | SPRING DRUM EARTH A |
| Парткод: | 302K002440 |
| Деталь: | SPRING DRUM EARTH B |
| Парткод: | 302K002640 |
| Деталь: | SPRING DRUM EARTH C |
| Парткод: | 302K002730 |
| Деталь: | REINFORCEMENT RETAINER |
| Парткод: | 302K002611 |
| Деталь: | PLATE RETAINER |
| Парткод: | 302NP03020 |
| Деталь: | BUSH RETAINER |
| Парткод: | 302K002630 |
| Деталь: | SHAFT RETAINER |
| Парткод: | 302K002420 |
| Деталь: | LEVER RETAINER |
| Парткод: | 302MV02280 |
| Деталь: | HOOK RETAINER L |
| Парткод: | 302K002430 |
| Деталь: | HOOK RETAINER R |
| Парткод: | 302K002390 |
| Деталь: | SPRING RETAINER R |
| Парткод: | 302K002451 |
| Деталь: | SPRING RETAINER L2 |
| Парткод: | 302K002E80 |
| Деталь: | SEAL WASTE |
| Парткод: | 302K002560 |
| Деталь: | LABEL E |
| Парткод: | 302MV34110 |
| Деталь: | PIN RETAINER |
| Парткод: | 302K002400 |
| Деталь: | SEAL ADJUST BK |
| Парткод: | 302K002240 |
| Деталь: | SEAL RETAINER |
| Парткод: | 302MV03030 |
| Деталь: | HOOK LEVER |
| Парткод: | 302NP03030 |
| Деталь: | +TP-FLAT T.T S SCREW 3X8 SR(BLACK) |
| Парткод: | 7BB782308H |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | +TP-CUP M SCREW 3X6 R |
| Парткод: | 7BB607306H |
| Деталь: | +BIND T.T S SCREW 3X10 SR |
| Парткод: | 7BB700310H |
| Деталь: | RAIL FEED |
| Парткод: | 303NN02370 |
| Деталь: | PULLEY CASSETTE RAIL |
| Парткод: | 302NL09030 |
| Деталь: | PIN CASSETTE RAIL |
| Парткод: | 2FB06710 |
| Деталь: | STAY FRONT FRAME |
| Парткод: | 302MV02040 |
| Деталь: | GUIDE ACTUATOR |
| Парткод: | 302K002590 |
| Деталь: | HOLDER SENSOR |
| Парткод: | 302MV06020 |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | WIRE LIMIT JUNCTION UPPER |
| Парткод: | 303NN46130 |
| Деталь: | STAY UPPER FEED |
| Парткод: | 303NN02143 |
| Деталь: | GUIDE PRIMARY FEED |
| Парткод: | 303NN02450 |
| Деталь: | ACTUATOR PAPER EMPTY |
| Парткод: | 302K002230 |
| Деталь: | WIRE LIFT FULL |
| Парткод: | 302K046300 |
| Деталь: | HOLDER CORD SENSOR |
| Парткод: | 302K002980 |
| Деталь: | RAIL DRUM R |
| Парткод: | 302K002340 |
| Деталь: | RAIL DRUM L |
| Парткод: | 302K002350 |
| Деталь: | RAIL DRUM BK |
| Парткод: | 302K002360 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | SHAFT BELT CLEANING DRIVE |
| Парткод: | 302K031730 |
| Деталь: | GEAR BELT CLEANING DRIVE Z30L |
| Парткод: | 302K031720 |
| Деталь: | GEAR BELT CLEANING DRIVE Z20L |
| Парткод: | 302K031740 |
| Деталь: | HOLDER CORD |
| Парткод: | 302NP39130 |
| Деталь: | WIRE DF POWER |
| Парткод: | 302NP46060 |
| Деталь: | ACCESS SADDLE |
| Парткод: | 7YZM610003++H01 |
| Деталь: | STAY HANDLE LEFT |
| Парткод: | 302K002110 |
| Деталь: | HANDLE COVER LEFT |
| Парткод: | 302MV02160 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610009++H01 |
| Деталь: | HOLDER CORD REAR |
| Парткод: | 302K002820 |
| Деталь: | PARTS PIPE TRANSFER CLEANING ASSY SP |
| Парткод: | 302K094041 |
| Деталь: | HOLDER CORD FRONT |
| Парткод: | 302K002C40 |
| Деталь: | MOUNT INTERLOCK SW |
| Парткод: | 302NP02060 |
| Деталь: | INTER LOCK SWITCH |
| Парткод: | 2FB27160 |
| Деталь: | WIRE FRONT/RIGHT SW |
| Парткод: | 302NP46160 |
| Деталь: | SHAFT TRANSFER CLEANING DRIVE |
| Парткод: | 302MV21110 |
| Деталь: | HOLDER CORD SENSOR SUB |
| Парткод: | 302K002770 |
| Деталь: | PIN FRONT CASSETTE RAIL |
| Парткод: | 302GR02240 |
| Деталь: | MOUNT DF CONNECTOR |
| Парткод: | 302NP39080 |
| Деталь: | SW.PUSH |
| Парткод: | 7SP01000004+H01 |
| Деталь: | PAD RAIL |
| Парткод: | 303MH06010 |
| Деталь: | SEAL WIRE A |
| Парткод: | 302H012330 |
| Деталь: | RAIL CASSETTE LEFT |
| Парткод: | 302NP02050 |
| Деталь: | RAIL CASSETTE RIGHT |
| Парткод: | 302NL02210 |
| Деталь: | LEVER LIFT CASSETTE |
| Парткод: | 302K302760 |
| Деталь: | HOLDER CASSETTE HOOK |
| Парткод: | 302NL09020 |
| Деталь: | LEVER CASSETTE HOOK |
| Парткод: | 302K909640 |
| Деталь: | PULLEY EJECT |
| Парткод: | 303LW24060 |
| Деталь: | SHAFT HOOK FULCRUM |
| Парткод: | 303NF02280 |
| Деталь: | SHAFT HOOK PULLEY |
| Парткод: | 302K909630 |
| Деталь: | SPRING CASSETTE HOOK |
| Парткод: | 302NL09060 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | PARTS MOTOR LIFT ASSY SP |
| Парткод: | 302K394190 |
| Цена: | 6 000 ₽ |
| Деталь: | PARTS MOTOR-BL W10 SP |
| Парткод: | -302LC94291 |
| Деталь: | PLATE MOTOR LOW |
| Парткод: | -302MV31030 |
| Деталь: | HOLDER DRIVE LOW A |
| Парткод: | -302MV31010 |
| Деталь: | SPRING EARTH FEED LOW |
| Парткод: | -302MV31040 |
| Деталь: | BUSH DRIVE |
| Парткод: | -302HN31590 |
| Деталь: | CLUTCH 50 Z35R |
| Парткод: | -302KV44041 |
| Деталь: | SHAFT CLUTCH FEED |
| Парткод: | -302K331240 |
| Деталь: | SHAFT GEAR |
| Парткод: | -303NN31060 |
| Деталь: | GEAR Z27L IDLE |
| Парткод: | -303NN31050 |
| Деталь: | GEAR Z40R IDLE |
| Парткод: | -302K331081 |
| Деталь: | GEAR Z77R Z23L |
| Парткод: | -303NN31040 |
| Деталь: | GEAR Z33R Z44R |
| Парткод: | -303NN31070 |
| Деталь: | HOLDER DRIVE LOW B |
| Парткод: | -302MV31020 |
| Деталь: | SPRING FEED |
| Парткод: | -302HN31410 |
| Деталь: | SPRING JOINT SHAFT |
| Парткод: | -303NN31080 |
| Деталь: | JOINT SHAFT CASSETTE |
| Парткод: | -302HN31660 |
| Деталь: | WIRE CASSETTE2 MOT/CLT 2 |
| Парткод: | 302MV46530 |
| Деталь: | WIRE RIGHT COVER 2 |
| Парткод: | 302MV46400 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | + BIND M SCREW 3X4 |
| Парткод: | 7BB000304H |
| Деталь: | DR-8315D |
| Парткод: | 302MV93110 |
| Деталь: | BOX CONTROLLER |
| Парткод: | 302NP39010 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210002++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610011++H01 |
| Деталь: | LID CONTROLLER |
| Парткод: | 302NL39100 |
| Деталь: | LID DP |
| Парткод: | 302NL39110 |
| Деталь: | LID FAX BOARD |
| Парткод: | 302NL39120 |
| Деталь: | LID WIRE GUIDE |
| Парткод: | 303LT02020 |
| Деталь: | FAN BOX COOLING |
| Парткод: | 302FZ44040 |
| Деталь: | BUSHING FAN |
| Парткод: | 302JD19140 |
| Деталь: | PLATE OPTION |
| Парткод: | 302K339050 |
| Деталь: | RAIL PWB |
| Парткод: | 302K939030 |
| Деталь: | SEAL MOTOR DC |
| Парткод: | 302LC31511 |
| Деталь: | Holder FFC |
| Парткод: | 302LF02380 |
| Деталь: | GUIDE WIRE FRONT PWB |
| Парткод: | 302LF39050 |
| Деталь: | BRACKET HDD |
| Парткод: | 302MV39040 |
| Деталь: | HOLDER FAN MAIN |
| Парткод: | 302MV39050 |
| Деталь: | PIN HDD |
| Парткод: | 302MV39340 |
| Деталь: | SPRING EARTH HDD |
| Парткод: | 302MV39350 |
| Деталь: | WIRE EARTH |
| Парткод: | 302MV46640 |
| Деталь: | BRACKET MAIN |
| Парткод: | 302NL39090 |
| Деталь: | WIRE KUIO POWER |
| Парткод: | 302NP46460 |
| Деталь: | WIRE FFC KUIO |
| Парткод: | 302NP46470 |
| Деталь: | SCREW OP / M3 X 8 CRFREE A4 |
| Парткод: | 5MMT263SN012++R |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210005++H01 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390011++H01 |
| Деталь: | DUCT OUT DLP D |
| Парткод: | 302MV33010 |
| Деталь: | WIRE HDD POWER |
| Парткод: | 302MV46210 |
| Деталь: | WIRE LVU-MAIN POWER |
| Парткод: | 302NP46040 |
| Деталь: | WIRE HDD SIG |
| Парткод: | 302NP46530 |
| Деталь: | PARTS PWB KUIO ASSY SP |
| Парткод: | 302K994270 |
| Деталь: | PARTS STORAGE DEVICE SP |
| Парткод: | 302MV93130 |
| Деталь: | PARTS PWB MAIN ASSY SP |
| Парткод: | 302NP94140 |
| Деталь: | PARTS PWB MAIN ASSY EU SP |
| Парткод: | 302NP94150 |
| Деталь: | PARTS MEMORY MODULE SP |
| Парткод: | 302LC94390 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610010++H01 |
| Деталь: | HOLDER WIRE D |
| Парткод: | 303LL02330 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | Вал переноса заряда |
| Парткод: | 302MV94330 |
| Цена: | 7 300 ₽ |
| Деталь: | PULLEY DU LOW |
| Парткод: | -302F929260 |
| Деталь: | SPRING GUIDE PULLEY |
| Парткод: | -302K028280 |
| Деталь: | PARTS ROLLER EXIT REVERSE SP |
| Парткод: | -302K094350 |
| Деталь: | BUSH SCREW |
| Парткод: | -302H702590 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | -5MVX111DN003 |
| Деталь: | BUSH 6 EW |
| Парткод: | -302H024370 |
| Деталь: | SPRING EXIT EARTH A |
| Парткод: | -302K028200 |
| Деталь: | PARTS GEAR Z22S EXIT SP |
| Парткод: | -302K394350 |
| Деталь: | GUIDE CHANGE |
| Парткод: | -302K028060 |
| Деталь: | SPRING SOLENOID A |
| Парткод: | -302K028190 |
| Деталь: | SHEET EXIT FRAME |
| Парткод: | -302K028300 |
| Деталь: | CAP SPRING /B-11 ENCLOSURE A4 |
| Парткод: | -2FM04150 |
| Деталь: | SPRING EXIT PULLEY |
| Парткод: | -302K028210 |
| Деталь: | SHAFT FEED |
| Парткод: | -302K324460 |
| Деталь: | GUIDE EXIT PUSH JS |
| Парткод: | -302K328290 |
| Деталь: | SPRING GUIDE EXIT PUSH |
| Парткод: | -302K328260 |
| Деталь: | GUIDE EXIT PUSH |
| Парткод: | -302K328090 |
| Деталь: | SENSOR OPT. |
| Парткод: | -7NXGP1S173LCH01 |
| Деталь: | WIRE EXIT UNIT2 |
| Парткод: | -302K046060 |
| Деталь: | COVER EXIT SENSOR |
| Парткод: | -302K028070 |
| Деталь: | PARTS SWITCH EXIT PAPER EMPTY SP |
| Парткод: | -302MV94650 |
| Деталь: | PLATE EXIT |
| Парткод: | -302KK28110 |
| Деталь: | SHEET PLATE EXIT |
| Парткод: | -302K028320 |
| Деталь: | ACTUATOR EXIT OVERFLOW LOW |
| Парткод: | -302K028080 |
| Деталь: | SPRING EXIT EARTH C |
| Парткод: | -302K028250 |
| Деталь: | PARTS ROLLER EXIT FD SP |
| Парткод: | -302K094340 |
| Деталь: | SHAFT GEAR BELT |
| Парткод: | -303MA16560 |
| Деталь: | GEAR Z23S EXIT |
| Парткод: | -302K028260 |
| Деталь: | SPRING EXIT EARTH D |
| Парткод: | -302K028270 |
| Деталь: | GEAR IDLE Z18S |
| Парткод: | -302KP29090 |
| Деталь: | PARTS GEAR Z74R-Z22S EXIT SP |
| Парткод: | -302K394340 |
| Деталь: | PARTS SOLENOID FEED SHIFT SP |
| Парткод: | -303LJ94150 |
| Деталь: | LEVER SOLENOID |
| Парткод: | -302K028160 |
| Деталь: | PLATE EXIT MOTOR |
| Парткод: | -302K028180 |
| Деталь: | RUBBER EXIT |
| Парткод: | -302K028310 |
| Деталь: | MOTOR REVERSE |
| Парткод: | -302HN44100 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | -7YZM610009++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | -7YZM610007++H01 |
| Деталь: | SPRING EXIT EARTH B |
| Парткод: | -302K028240 |
| Деталь: | ACTUATOR EXIT OVERFLOW UP |
| Парткод: | -302K028090 |
| Деталь: | STATIC ELIMINATOR,EJECT |
| Парткод: | -63212210 |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | + BIND M SCREW 3X3 |
| Парткод: | 7BB000303H |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | + BIND T.T P SCREW 4X10 |
| Парткод: | 7BB200410H |
| Деталь: | PARTS EXIT UNIT SP |
| Парткод: | 302K094010 |
| Деталь: | CASE WASTE A |
| Парткод: | 302K003022 |
| Деталь: | SEAL CASE WASTE C |
| Парткод: | 302K003280 |
| Деталь: | SEAL CASE WASTE D |
| Парткод: | 302K003331 |
| Деталь: | BUSH WASTE |
| Парткод: | 302K003160 |
| Деталь: | SHAFT WASTE DRIVE |
| Парткод: | 302K003170 |
| Деталь: | JOINT WASTE C |
| Парткод: | 302K003140 |
| Деталь: | GEAR WASTE Z13L |
| Парткод: | 302K003110 |
| Деталь: | SCREW WASTE |
| Парткод: | 302K003050 |
| Деталь: | GEAR SCREW WASTE Z13L |
| Парткод: | 302K003060 |
| Деталь: | BUSH SCREW WASTE |
| Парткод: | 302K003290 |
| Деталь: | CASE WASTE B |
| Парткод: | 302K003031 |
| Деталь: | SEAL CASE WASTE B |
| Парткод: | 302K003270 |
| Деталь: | SEAL CASE WASTE A |
| Парткод: | 302K003260 |
| Деталь: | COVER SENSOR |
| Парткод: | 302K003320 |
| Деталь: | PLATE WASTE |
| Парткод: | 302MV03020 |
| Деталь: | LOCK WASTE A |
| Парткод: | 302K003092 |
| Деталь: | LOCK WASTE B |
| Парткод: | 302K003102 |
| Деталь: | SPRING LOCK WASTE |
| Парткод: | 302K003231 |
| Деталь: | SEAL SHUTTER WASTE |
| Парткод: | 302K003250 |
| Деталь: | CASE SENSOR |
| Парткод: | 302K003041 |
| Деталь: | PARTS TONER FULL DETECT ASSY SP |
| Парткод: | 302K094280 |
| Деталь: | SPACER LED /43587J2063 A4 |
| Парткод: | 5MVS313SB002 |
| Деталь: | SHUTTER WASTE TONER |
| Парткод: | 302K003070 |
| Деталь: | SPRING SHUTTER WASTE |
| Парткод: | 302K003200 |
| Деталь: | HOUSING WASTE |
| Парткод: | 302NP03010 |
| Деталь: | PLATE HOUSING WASTE |
| Парткод: | 302K003620 |
| Деталь: | LEVER WASTE |
| Парткод: | 302MV03040 |
| Деталь: | LABEL D |
| Парткод: | 302MV34100 |
| Деталь: | SPRING LEVER WASTE |
| Парткод: | 302K003220 |
| Деталь: | LABEL PUSH |
| Парткод: | 302MV34240 |
| Деталь: | ARM WASTE |
| Парткод: | 302K002B50 |
| Деталь: | SPRING ARM WASTE |
| Парткод: | 302K002B60 |
| Деталь: | STRAP COVER FRONT R |
| Парткод: | 302K304230 |
| Деталь: | STRAP COVER FRONT L |
| Парткод: | 302K304320 |
| Деталь: | WT-895 |
| Парткод: | 302K093110 |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | Ролик подачи бумаги |
| Парткод: | 302F906230 |
| Цена: | 750 ₽ |
| Деталь: | Ролик отделения бумаги |
| Парткод: | 302F909171 |
| Цена: | 900 ₽ |
| Деталь: | Ролик захвата бумаги |
| Парткод: | 302HN06080 |
| Цена: | 480 ₽ |
| Деталь: | Резина ролика отделения бумаги |
| Парткод: | CET4322PT |
| Цена: | 110 ₽ |
| Деталь: | Резина ролика захвата бумаги |
| Парткод: | CET7806BPT |
| Цена: | 110 ₽ |
| Деталь: | Резина ролика подачи бумаги |
| Парткод: | CET7829 |
| Цена: | 150 ₽ |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510007++H01 |
| Деталь: | PARTS UNIT LOW VOLTAGE 200 SP |
| Парткод: | 302NP94090 |
| Цена: | 21 400 ₽ |
| Деталь: | PARTS UNIT LOW VOLTAGE 100 SP |
| Парткод: | 302NP94080 |
| Деталь: | BOX POWER |
| Парткод: | 302NP39020 |
| Деталь: | SHEET BOX POWER |
| Парткод: | 302MV39320 |
| Деталь: | BRACKET FAN POWER |
| Парткод: | 302MV39250 |
| Деталь: | PARTS,FAN COOLING CONVEYING SP |
| Парткод: | 302FZ94420 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610010++H01 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610012++H01 |
| Деталь: | LID POWER |
| Парткод: | 302MV39220 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC02B1111 + H01 |
| Деталь: | ACCESS.SPACER |
| Парткод: | 7YZM510021++H01 |
| Деталь: | SEAL MOTOR DC |
| Парткод: | 302LC31511 |
| Деталь: | WIRE DP |
| Парткод: | 302NP46360 |
| Деталь: | SPACER,SFS-2.6S-B1WM(JST) |
| Парткод: | M0208010 |
| Деталь: | MOUNT DP CONNECTOR |
| Парткод: | 302NP39150 |
| Деталь: | ACCESS.EDGING |
| Парткод: | 7YZM210005++H01 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610009++H01 |
| Деталь: | SHUTTER ID SENSOR CLEANING |
| Парткод: | 302K002870 |
| Деталь: | FELT CLEANER ID |
| Парткод: | 302HN02970 |
| Деталь: | SPRING ID CLEANING |
| Парткод: | 302K002C60 |
| Деталь: | CASE ID SENSOR CLEANING |
| Парткод: | 302K002860 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXGP1S173LCH01 |
| Деталь: | WIRE ID SENS MOT/PI |
| Парткод: | 302K046420 |
| Деталь: | WORM-WHEEL ID SENSOR CLEANING |
| Парткод: | 302K002880 |
| Деталь: | GEAR ID SENSOR CLEANING Z71R |
| Парткод: | 302K002890 |
| Деталь: | ARM ID SENSOR CLEANING |
| Парткод: | 302K002900 |
| Деталь: | PARTS MOTOR-DC ASSY C SP |
| Парткод: | 302K094090 |
| Деталь: | CONNECTOR |
| Парткод: | 7YCC02B1202+H01 |
| Деталь: | PARTS ID SENSOR ASSY SP |
| Парткод: | 302K094290 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | ACTUATOR REGIST |
| Парткод: | 302K306140 |
| Деталь: | SPRING ACTUATOR REGIST |
| Парткод: | 302K306150 |
| Деталь: | GUIDE FEED CASSETTE |
| Парткод: | 302K002172 |
| Деталь: | SPRING EARTH MIDDLE |
| Парткод: | 302K002540 |
| Деталь: | BUSH MIDDLE |
| Парткод: | 302K002C00 |
| Деталь: | PARTS ROLLER MIDDLE SP |
| Парткод: | 302K094330 |
| Деталь: | GEAR Z27L CLUTCH |
| Парткод: | 302HS31120 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | SHEET GUIDE FEED |
| Парткод: | 302K002D70 |
| Деталь: | SHEET REGIST |
| Парткод: | 302K002500 |
| Деталь: | WIRE RESIST |
| Парткод: | 302K046380 |
| Деталь: | WIRE ID SENSOR |
| Парткод: | 302K046310 |
| Деталь: | PLATE ID SENSOR |
| Парткод: | 302K002130 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | Крышка планшетного сканера |
| Парткод: | 1202H70UN0 |
| Цена: | 4 200 ₽ |
| Деталь: | Ограничитель формата бумаги в кассете на 500 листов |
| Парткод: | 302K309270 |
| Цена: | 120 ₽ |
| Деталь: | GEAR Z27S Z27R |
| Парткод: | 302K902401 |
| Деталь: | GEAR Z14R |
| Парткод: | 302K902391 |
| Деталь: | PARTS MOTOR-DC ASSY C SP |
| Парткод: | 302K094090 |
| Деталь: | PARTS GEAR Z32L SP |
| Парткод: | 302K994520 |
| Деталь: | PARTS PWB LSU CONNECT ASSY SP |
| Парткод: | 302K094170 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | LK-8325 |
| Парткод: | 302NP93120 |
| Деталь: | SPRING-COMPRESSION LSU RETAINING |
| Парткод: | 302K902480 |
| Деталь: | PIN LSU RETAINING |
| Парткод: | 302K902470 |
| Деталь: | ACCESS.CLAMP |
| Парткод: | 7YZM390003++H01 |
| Деталь: | WIRE ENGINE MAIN-LSU CONNECT 2 |
| Парткод: | 302K046200 |
| Деталь: | WIRE MAIN-LSU CONNECT 2 |
| Парткод: | 302K046220 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | + BIND M SCREW 3X4 |
| Парткод: | 7BB000304H |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | ELA UNIT-TRANSFER |
| Парткод: | TR-8315B |
| Цена: | 4 200 ₽ |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325C |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325K |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325M |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325Y |
| Деталь: | Formatter, exchange, HP Color LaserJet 3000dn and 3000dtn Series only (256 MB) |
| Парткод: | 302NP94151 |
| Цена: | 81 100 ₽ |
| Деталь: | LASER SCANNER ASSY |
| Парткод: | LK-8325 |
| Цена: | 22 600 ₽ |
| Деталь: | Правая часть узла термозакрепления, в сборе (220В) |
| Парткод: | FK-8325 |
| Цена: | 28 900 ₽ |
| Деталь: | Левая часть узла термозакрепления, в сборе (220В) |
| Парткод: | FK-8507 |
| Цена: | 15 900 ₽ |
| Деталь: | Комплект для технического обслуживания |
| Парткод: | MK-8325B |
| Деталь: | Комплект для технического обслуживания |
| Парткод: | MK-8325A |
| Деталь: | DUCT INPUT DLP A |
| Парткод: | 302K033060 |
| Деталь: | PARTS FAN COOLING LSU 60 SP |
| Парткод: | 302LC94380 |
| Деталь: | PARTS,FAN COOLING CONVEYING SP |
| Парткод: | 302FZ94420 |
| Деталь: | WIRE FAN MOT DLP/LSU |
| Парткод: | 302K046370 |
| Деталь: | DUCT INPUT DLP B |
| Парткод: | 302K033070 |
| Деталь: | SPRING DUCT |
| Парткод: | 302K033090 |
| Деталь: | DUCT INPUT DLP C |
| Парткод: | 302K033080 |
| Деталь: | PARTS DUCT OUTPUT DLP IN ASSY SP |
| Парткод: | 302MV94050 |
| Деталь: | STAY SHIELD IH |
| Парткод: | 302K002740 |
| Деталь: | DUCT EXIT |
| Парткод: | 302K033012 |
| Деталь: | DUCT HIGH VOLTAGE |
| Парткод: | 302K002C21 |
| Деталь: | GUIDE FUSER |
| Парткод: | 302MV02360 |
| Деталь: | SPRING IH |
| Парткод: | 302K926220 |
| Деталь: | CAP SPRING |
| Парткод: | 302LK26050 |
| Деталь: | PIN READING GUIDE |
| Парткод: | 303LL24250 |
| Деталь: | DUCT IH COIL |
| Парткод: | 302K002C70 |
| Деталь: | SPONGE IH COIL |
| Парткод: | 302K002D00 |
| Деталь: | DUCT CONTAINER B |
| Парткод: | 302MV33020 |
| Деталь: | DUCT CONTAINER C |
| Парткод: | 302MV33030 |
| Деталь: | BRACKET FAN DLP |
| Парткод: | 302K002261 |
| Деталь: | PARTS,FAN COOLING DLP 70 SP |
| Парткод: | 302FZ94380 |
| Деталь: | PARTS FAN COOLING LSU 60 SP |
| Парткод: | 302K994360 |
| Деталь: | SEAL DLP FAN |
| Парткод: | 302K002D60 |
| Деталь: | DUCT CONTAINER A |
| Парткод: | 302K002790 |
| Деталь: | WIRE IH-DLP FAN |
| Парткод: | 302MV46680 |
| Деталь: | DUCT IH |
| Парткод: | 302K002191 |
| Деталь: | DUCT IH COVER |
| Парткод: | 302K002781 |
| Деталь: | DUCT OUT DLP C |
| Парткод: | 302K033040 |
| Деталь: | PARTS FAN MOTOR SP |
| Парткод: | 302NG94220 |
| Деталь: | WIRE FAN MOT LVU |
| Парткод: | 302MV46070 |
| Деталь: | PARTS FAN MOTOR SET SP |
| Парткод: | 302MV94560 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | + BIND T.T P SCREW 3X12 |
| Парткод: | 7BB200312H |
| Деталь: | +BIND T.T S SCREW 3X20 SR |
| Парткод: | 7BB700320H |
| Деталь: | BASE CONVEYING |
| Парткод: | -302K024014 |
| Деталь: | TERMINAL TRANSFER B |
| Парткод: | -302K024140 |
| Деталь: | TERMINAL SEPARATION A |
| Парткод: | -302K024151 |
| Деталь: | GUIDE CONVEYING |
| Парткод: | -302K024110 |
| Деталь: | SPRING EARTH CONVEYING |
| Парткод: | -302K024160 |
| Деталь: | SENSOR,CONVEYING |
| Парткод: | -3H327410 |
| Деталь: | WIRE CONVEYING UNIT PI |
| Парткод: | -302K046890 |
| Деталь: | HOLDER SENSOR |
| Парткод: | -302K024380 |
| Деталь: | LEVER CONVEYING F |
| Парткод: | -302K024232 |
| Деталь: | SPRING CONVEYING F |
| Парткод: | -302K324110 |
| Деталь: | LEVER CONVEYING R |
| Парткод: | -302K024242 |
| Деталь: | SPRING CONVEYING R |
| Парткод: | -302K324360 |
| Деталь: | FRAME DU |
| Парткод: | -302K024271 |
| Деталь: | ACTUATOR DU |
| Парткод: | -302K329040 |
| Деталь: | RETAINER ACTUATOR |
| Парткод: | -302K329060 |
| Деталь: | SENSOR OPT. |
| Парткод: | -7NXGP1S173LCH01 |
| Деталь: | PARTS FAN MOTOR SET SP |
| Парткод: | -302MV94560 |
| Деталь: | COVER DUCT FRONT |
| Парткод: | -302K024310 |
| Деталь: | COVER DUCT REAR |
| Парткод: | -302K024320 |
| Деталь: | SHEET FAN PRESS |
| Парткод: | -302K024330 |
| Деталь: | PULLEY DU |
| Парткод: | -302K329020 |
| Деталь: | SPRING DU FEED |
| Парткод: | -302K329030 |
| Деталь: | WIRE CONVEYING UNIT |
| Парткод: | -302K046041 |
| Деталь: | FRAME DU B |
| Парткод: | -302K024280 |
| Деталь: | BASE CONVEYING SUB |
| Парткод: | -302K024300 |
| Деталь: | PARTS ROLLER REGIST RIGHT SP |
| Парткод: | -302K094420 |
| Деталь: | BUSH REGIST F |
| Парткод: | -302K324180 |
| Деталь: | BUSH REGIST R |
| Парткод: | -302K324270 |
| Деталь: | SHEET REGIST R |
| Парткод: | -302K024220 |
| Деталь: | SHEET REGIST LOW |
| Парткод: | -302K024431 |
| Деталь: | SPRING REGIST F |
| Парткод: | -302K024440 |
| Деталь: | PARTS GEAR REGIST Z24R SP |
| Парткод: | -302K394330 |
| Деталь: | COLLAR TRANS ROLLER |
| Парткод: | -302H722470 |
| Деталь: | BUSH SPRING FEED |
| Парткод: | -302KV24090 |
| Деталь: | SPRING MIDDLE PULLEY |
| Парткод: | -302K024190 |
| Деталь: | SHAFT FEED |
| Парткод: | -302K324460 |
| Деталь: | PULLEY MIDDLE |
| Парткод: | -302MV24030 |
| Деталь: | COVER HARNESS |
| Парткод: | -302K024250 |
| Деталь: | SPRING REGIST R |
| Парткод: | -302K024450 |
| Деталь: | SHAFT RIGHT COVER F |
| Парткод: | 302K304550 |
| Деталь: | SHAFT RIGHT COVER R |
| Парткод: | 302K304560 |
| Деталь: | FILM CONVEYING SHAFT |
| Парткод: | 302K304630 |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | +TP-CUP M SCREW 3X12 R |
| Парткод: | 7BB607312H |
| Деталь: | PARTS CONVEYING UNIT SP |
| Парткод: | 302MV94431 |
| Деталь: | ACTUATOR SIZE DETECTION |
| Парткод: | -302K908211 |
| Деталь: | SPRING-TORSION SIZE DETECTION |
| Парткод: | -302K908220 |
| Деталь: | HOLDER SIZE DETECTION |
| Парткод: | -302K908580 |
| Деталь: | SENSOR OPT. |
| Парткод: | -7NXGP1S173LCH01 |
| Деталь: | WIRE MPF SIZE UNIT 2 |
| Парткод: | -302MV46510 |
| Деталь: | TABLE MPF B |
| Парткод: | -302MV08430 |
| Деталь: | SPONGE WIRE MPT |
| Парткод: | -302H708150 |
| Деталь: | TABLE MPF A |
| Парткод: | -302MV08420 |
| Деталь: | TABLE MPF |
| Парткод: | -302MV08410 |
| Деталь: | CURSOR FRONT MPF |
| Парткод: | -302MV08440 |
| Деталь: | CURSOR REAR MPF |
| Парткод: | -302MV08450 |
| Деталь: | GEAR 18 BYPASS |
| Парткод: | -2C906080 |
| Деталь: | TERMINAL PAPER SIZE |
| Парткод: | -2C906090 |
| Деталь: | PCB MPF SIZE ASSY |
| Парткод: | -2C901050 |
| Деталь: | GUIDE FRONT MPF WIRE |
| Парткод: | -302MV08460 |
| Деталь: | ORIGINAL SIZE SWITCH |
| Парткод: | -76727010 |
| Деталь: | GUIDE REAR MPF WIRE |
| Парткод: | -302MV08470 |
| Деталь: | STOPPER BYPASS TABLE |
| Парткод: | -2FB07330 |
| Деталь: | SPRING MPF |
| Парткод: | -302MV08500 |
| Деталь: | COVER MPF |
| Парткод: | -302MV08400 |
| Деталь: | STRAP LINK MPF |
| Парткод: | -302K308460 |
| Деталь: | STOPPER STRAP |
| Парткод: | -302K308470 |
| Деталь: | LABEL BYPASS TABLE |
| Парткод: | -302MV34270 |
| Деталь: | SHEET MPF WIRE A |
| Парткод: | -302MV08520 |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | PARTS MPF TABLE ASSY SP |
| Парткод: | 302MV94080 |
| Деталь: | STAY RIGHT HANDLE |
| Парткод: | 302K302140 |
| Деталь: | GUIDE FEED INNER |
| Парткод: | 302MV07040 |
| Деталь: | SENSOR OPT |
| Парткод: | -7NXGP1S173LCH01 |
| Деталь: | BASE MPF |
| Парткод: | -302MV08010 |
| Деталь: | PARTS GEAR MPF Z28 SP |
| Парткод: | -302K394320 |
| Деталь: | SEAL SIDE MPF |
| Парткод: | -302K308480 |
| Деталь: | WIRE MPF SIZE UNIT 1 |
| Парткод: | -302MV46450 |
| Деталь: | WIRE MPF |
| Парткод: | -302MV46580 |
| Деталь: | ACTUATOR MPF |
| Парткод: | -302K308020 |
| Деталь: | SPRING ACTUATOR |
| Парткод: | -302K308250 |
| Деталь: | SPRING LIFT R |
| Парткод: | -302K308120 |
| Деталь: | SPRING LIFT F |
| Парткод: | -302K308130 |
| Деталь: | LIFT PLATE |
| Парткод: | -302K308101 |
| Деталь: | PAD LIFT |
| Парткод: | -302K308110 |
| Деталь: | SEAL GUIDE PAD |
| Парткод: | -302K308340 |
| Деталь: | ARM LIFT |
| Парткод: | -302K308140 |
| Деталь: | SPRING EARTH |
| Парткод: | -302K308240 |
| Деталь: | GUIDE UPPER MPF |
| Парткод: | -302K308030 |
| Деталь: | WIRE EARTH MPF |
| Парткод: | -302K308260 |
| Деталь: | BUSH 10 |
| Парткод: | -302K308070 |
| Деталь: | LABEL J |
| Парткод: | -302MV34190 |
| Деталь: | SHAFT MPF |
| Парткод: | -302K308080 |
| Деталь: | PARTS PAD SEPARATION ASSY SP |
| Парткод: | -302MV94010 |
| Деталь: | ROLLER MPF |
| Парткод: | - -302K308150 |
| Деталь: | PULLEY MPF |
| Парткод: | - -302MV08030 |
| Деталь: | SPRING MPF ROLL |
| Парткод: | - -302K308270 |
| Деталь: | PIN FEED ROLL |
| Парткод: | - -302MV08020 |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | PARTS MPF UNIT SP |
| Парткод: | 302MV94070 |
| Деталь: | PARTS ROLLER MPF ASSY SP |
| Парткод: | -302MV94020 |
| Деталь: | GUIDE FEED OUT |
| Парткод: | 302MV07011 |
| Деталь: | PARTS ROLLER FEED UPPER SP |
| Парткод: | 302MV94310 |
| Деталь: | BUSH DU |
| Парткод: | 302K329270 |
| Деталь: | STOPPER 3 /2BT1107 A4 |
| Парткод: | 5MVX111DN007 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | PULLEY 26-6 DUPLEX |
| Парткод: | 303MR29040 |
| Деталь: | PULLEY PA |
| Парткод: | 302HN24400 |
| Деталь: | ACTUATOR DECK FEED |
| Парткод: | 302K302831 |
| Деталь: | SPRING EARTH FEED |
| Парткод: | 302MV07120 |
| Деталь: | GUIDE FEED LOW |
| Парткод: | 302MV07020 |
| Деталь: | PARTS ROLLER FEED LOWER SP |
| Парткод: | 302MV94320 |
| Деталь: | JOINT PULLEY 26-6 |
| Парткод: | 303NN24110 |
| Деталь: | ACTUATOR REGIST |
| Парткод: | 302K306140 |
| Деталь: | SPRING ACTUATOR REGIST |
| Парткод: | 302K306150 |
| Деталь: | GUIDE FEED |
| Парткод: | 302MV07030 |
| Деталь: | GUIDE TRANSFER LEFT |
| Парткод: | 302K002A20 |
| Деталь: | PARTS ROLLER REGIST LEFT SP |
| Парткод: | 302K394230 |
| Деталь: | BUSH 8 |
| Парткод: | 302H024830 |
| Деталь: | BUSH 8 EW |
| Парткод: | 302H024360 |
| Цена: | 30 ₽ |
| Деталь: | PARTS GEAR REGIST Z28L-Z18L SP |
| Парткод: | 302K394310 |
| Деталь: | STOPPER 6 |
| Парткод: | 2BC06910 |
| Деталь: | SPRING EARTH REG C |
| Парткод: | 302K002D40 |
| Деталь: | GUIDE REGIST FRONT |
| Парткод: | 302K002271 |
| Деталь: | VARISTOR TC |
| Парткод: | 302K345120 |
| Деталь: | SPRING EARTH REG D |
| Парткод: | 302K002490 |
| Деталь: | SPRING EARTH REG B |
| Парткод: | 302K002480 |
| Деталь: | SPRING EARTH REG A |
| Парткод: | 302K002470 |
| Деталь: | GUIDE REGIST REAR |
| Парткод: | 302K002280 |
| Деталь: | TERMINAL SEPARATION B |
| Парткод: | 302K002520 |
| Деталь: | TERMINAL TRANSFER C |
| Парткод: | 302K002510 |
| Деталь: | BELT FEED |
| Парткод: | 302MV07110 |
| Деталь: | SHEET GUIDE CASSETTE |
| Парткод: | 302K002E00 |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | COVER ISU REAR |
| Парткод: | 302NL04150 |
| Деталь: | COVER ISU RIGHT |
| Парткод: | 302NL04140 |
| Деталь: | COVER ISU LEFT |
| Парткод: | 302NL04131 |
| Деталь: | COVER ISU LEFT SUB |
| Парткод: | 302LC04340 |
| Деталь: | LABEL OPERATION CAUTION B |
| Парткод: | -302LC34031 |
| Деталь: | COVER ISU FRONT |
| Парткод: | 302NP04120 |
| Деталь: | CASE CLIP |
| Парткод: | 302N404130 |
| Деталь: | SEAL MAGNET |
| Парткод: | 302GR04380 |
| Деталь: | MAGNET CLIP DISH |
| Парткод: | 302GR04370 |
| Деталь: | LID USB FRONT |
| Парткод: | 302N404241 |
| Деталь: | LID ISU FRONT |
| Парткод: | 302NL04220 |
| Деталь: | LID CARD |
| Парткод: | 302N404040 |
| Деталь: | MOUNT USB |
| Парткод: | 302NL04230 |
| Деталь: | BUSH SLIDE OPE |
| Парткод: | 302H005340 |
| Деталь: | WIRE USB CARD READER |
| Парткод: | 302NP46520 |
| Деталь: | SPRING USB HOLD |
| Парткод: | 302K905900 |
| Деталь: | LID DP |
| Парткод: | 302NL04210 |
| Деталь: | WIRE USB KEY BOARD |
| Парткод: | 302NP46510 |
| Деталь: | PIN COVER |
| Парткод: | 303MH04040 |
| Деталь: | +TP-FLAT T.T S SCREW 3X8 SR(BLACK) |
| Парткод: | 7BB782308H |
| Деталь: | + BIND M SCREW 3X6 |
| Парткод: | 7BB000306H |
| Деталь: | +BIND T.T S SCREW 3X12 SR |
| Парткод: | 7BB700312H |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | PARTS COVER ISU FRONT A ASSY E SP |
| Парткод: | 302NP94200 |
| Деталь: | DV-8325K |
| Парткод: | 302NP93050 |
| Деталь: | DV-8325M |
| Парткод: | 302NP93060 |
| Деталь: | DV-8325C |
| Парткод: | 302NP93040 |
| Деталь: | DV-8325Y |
| Парткод: | 302NP93070 |
| Деталь: | HOLDER FEED DRIVE A |
| Парткод: | -302K031501 |
| Деталь: | SPRING EARTH F |
| Парткод: | -302K031570 |
| Деталь: | PARTS MOTOR-BL W20 SP |
| Парткод: | -302K994321 |
| Деталь: | PLATE FEED DRIVE |
| Парткод: | -302K031560 |
| Деталь: | CONNECTOR 292254-2 |
| Парткод: | -7YCC02B1003+H01 |
| Деталь: | BUSH DRIVE |
| Парткод: | -302HN31590 |
| Деталь: | SOLENOID MPF |
| Парткод: | -302HN44160 |
| Деталь: | PIN DRIVE MT |
| Парткод: | -302HN31640 |
| Деталь: | PIN DRIVE A |
| Парткод: | -302K331260 |
| Деталь: | CLUTCH 50 Z35R |
| Парткод: | -302KV44041 |
| Деталь: | SHAFT CLUTCH FEED |
| Парткод: | -302K331240 |
| Деталь: | GEAR Z30L OUTPUT CL |
| Парткод: | -302K031550 |
| Деталь: | GEAR Z32L |
| Парткод: | -302K331130 |
| Деталь: | GEAR Z84R-Z27L |
| Парткод: | -302K031520 |
| Деталь: | GEAR Z61R-Z32R |
| Парткод: | -302K031530 |
| Деталь: | GEAR Z32L IDLE |
| Парткод: | -302K031540 |
| Деталь: | GEAR Z40R IDLE |
| Парткод: | -302K331081 |
| Деталь: | GEAR Z43L IDLE |
| Парткод: | -302K331090 |
| Деталь: | GEAR Z30R IDLE |
| Парткод: | -302K331140 |
| Деталь: | GEAR MIDDLE CLN Z27L-Z21L |
| Парткод: | -302K031300 |
| Деталь: | GEAR Z48R-Z22S |
| Парткод: | -302K331160 |
| Деталь: | GEAR Z42R-Z36R |
| Парткод: | -302K331150 |
| Деталь: | GEAR Z45S INPUT MPF A |
| Парткод: | -302K331180 |
| Деталь: | SPRING INPUT MPF |
| Парткод: | -302HN31650 |
| Деталь: | GEAR Z45S INPUT MPF B |
| Парткод: | -302K331190 |
| Деталь: | HOLDER FEED DRIVE B |
| Парткод: | -302K031511 |
| Деталь: | BUSH DRIVE 8 |
| Парткод: | -302K331230 |
| Деталь: | GEAR Z28S |
| Парткод: | -302K331170 |
| Деталь: | SPRING FEED |
| Парткод: | -302HN31410 |
| Деталь: | JOINT SHAFT CASSETTE |
| Парткод: | -302HN31660 |
| Деталь: | CAM MPF |
| Парткод: | -302K331200 |
| Деталь: | WIRE FEED UNIT 2 |
| Парткод: | -302K046020 |
| Деталь: | + BIND M SCREW 3X4 |
| Парткод: | 7BB000304H |
| Деталь: | + BIND T.T P SCREW 3X8 |
| Парткод: | 7BB200308H |
| Деталь: | +BIND T.T S SCREW 3X8 SR |
| Парткод: | 7BB700308H |
| Деталь: | DR-895C |
| Парткод: | 302K093142 |
| Деталь: | ELA UNIT-TRANSFER |
| Парткод: | TR-8315B |
| Цена: | 4 200 ₽ |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325C |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325K |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325M |
| Деталь: | MEA UNIT-DEV Y |
| Парткод: | DV-8325Y |
| Деталь: | Formatter, exchange, HP Color LaserJet 3000dn and 3000dtn Series only (256 MB) |
| Парткод: | 302NP94151 |
| Цена: | 81 100 ₽ |
| Деталь: | LASER SCANNER ASSY |
| Парткод: | LK-8325 |
| Цена: | 22 600 ₽ |
| Деталь: | Правая часть узла термозакрепления, в сборе (220В) |
| Парткод: | FK-8325 |
| Цена: | 28 900 ₽ |
| Деталь: | Левая часть узла термозакрепления, в сборе (220В) |
| Парткод: | FK-8507 |
| Цена: | 15 900 ₽ |
| Деталь: | Комплект для технического обслуживания |
| Парткод: | MK-8325B |
| Деталь: | Комплект для технического обслуживания |
| Парткод: | MK-8325A |
| Деталь: | GUIDE WIRE MAIN DRIVE |
| Парткод: | 302K031462 |
| Деталь: | GUIDE WIRE ENGINE SUB |
| Парткод: | 302K039320 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610013 |
| Деталь: | LID ENGINE SUB |
| Парткод: | 302K039100 |
| Деталь: | PARTS PWB ENGINE CONNECT ASSY SP |
| Парткод: | 302NP94110 |
| Деталь: | WIRE ENGINE2 - DRUM/DLP CONNECT |
| Парткод: | 302K046340 |
| Деталь: | WIRE ENGINE1-2 MOT |
| Парткод: | 302NP46200 |
| Деталь: | GUIDE WIRE SUB |
| Парткод: | 302K031620 |
| Деталь: | LID WIRE GUIDE |
| Парткод: | 303LT02020 |
| Деталь: | WIRE ENGINE-LVU |
| Парткод: | 302MV46410 |
| Деталь: | Ремень подачи бумаги в автоподатчике документов |
| Парткод: | 303LL07531 |
| Цена: | 1 900 ₽ |
| Деталь: | Ролик захвата бумаги в узле автоматической подачи документов |
| Парткод: | 36211110 |
| Цена: | 750 ₽ |
| Деталь: | Пружина |
| Парткод: | 302HN31650 |
| Цена: | 150 ₽ |
Коды ошибок
0030
0070
0100
0120
0130
0140
0150
0160
0170
0180
0350
0620
0630
0640
0650
0660
0670
0800
0830
0840
0870
0920
0980
1010
1020
1030
1040
1100
1110
1800
1900
2101
2102
2111
2112
2201
2202
2211
2212
2300
2310
2500
2510
2550
2560
2600
2610
2700
3100
3210
3220
3300
3310
3500
3600
3700
3800
3900
4001
4002
4003
4004
4011
4012
4013
4014
4101
4102
4103
4104
4201
4202
4203
4204
4600
6000
6020
6030
6040
6050
6120
6130
6150
6200
6220
6230
6250
6410
6600
6710
6720
6730
6740
6750
6760
6770
6930
6950
6990
7101
7102
7103
7104
7401
7402
7403
7404
7411
7412
7413
7414
7420
7601
7602
7611
7612
7613
7614
7620
7800
7810
7901
7902
7903
7904
7911
7912
7913
7914
8010
8020
8030
8090
8100
8140
8150
8160
8170
8180
8190
8200
8210
8230
8240
8260
8410
8420
8430
8800
8900
8990
9000
9010
9040
9050
9060
9070
9080
9100
9110
9120
9130
9140
9150
9160
9170
9500
9510
9520
9530
9540
9550
F000
F010 ... F013
F020 ... F023
F040
F041
F050
F051
Описание
| Error code: | 0030 |
| Description: | FAX control PWB system error Processing with the fax software was disabled due to a software problem. |
| Causes: | Defective FAX control PWB. |
| Remedy: | FAX control PWB 1. Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on. 2. Reinstall the fax software. 3. Replace the FAX control PWB. |
| Error code: | 0070 |
| Description: | FAX control PWB incompatible detection error Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
| Causes: | Defective FAX software. Defective FAX control PWB. |
| Remedy: | FAX control PWB (The FAX PWB installed will not be the one designed for the machine.) 1. Install the FAX system designed for the model. 2. Reinstall the fax software. |
| Error code: | 0100 |
| Display: | MAINTENANCE CALL 0100 |
| Description: | Backup memory device error |
| Causes: | Defective flash memory. Defective main PWB. |
| Remedy: | EEPROM (main PWB) 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the EEPROM on the main circuit PWB is peroperly installed on the main circuit PWB and, if not, re-install it. 3. Replace the main PWB |
| Error code: | 0120 |
| Description: | There is a problem with Thermistor for Pre-Heater. |
| Causes: | Thermistor Cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0130 |
| Description: | There is a problem with Thermistor for Print Heater. |
| Causes: | Thermistor cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0140 |
| Description: | There is a problem with Thermistor for dryer. |
| Causes: | Thermistor cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0150 |
| Description: | Even though the machine carries out the regular movement, the output of Slider Sensor does not reach the expected value. |
| Causes: | Slider Motor has a problem. Slider Sensor has a problem. Wiring or Flexible Cable has short circuitted or cut-line. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Slider Motor replacement Slider Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0160 |
| Description: | Even though the machine carries out the regular movement, the output of Pressure Pump 1 Sensor does not reach the expected value. |
| Causes: | Pressure Pump 1 Motor has a problem. Pressure Pump 1 Sensor has a problem. Pressure Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Pressure Pump 1 Magnet Pressure Pump 1 Motor replacement Pressure Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0170 |
| Description: | Even though the machine carries out the regular movement, the output of Supply Pump 1 Sensor does not reach the expected value. |
| Causes: | Supply Pump 1 Motor has a problem. Supply Pump 1 Sensor has a problem. Supply Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Supply Pump 1 Magnet Supply Pump 1 Motor replacement Supply Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0180 |
| Description: | Even though the machine carries out the regular movement, the output of Maintenance Liquid Pump Sensor does not reach the expected value. |
| Causes: | Maintenance Liquid Pump Motor has a problem. Maintenance Liquid Pump Sensor has a problem. Maintenance Liquid Pump Magnet has dropped out. Wiring or Flexible Cable has short circuitted |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Maintenance Liquid Pump Motor replacement Maintenance Liquid Pump Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0350 |
| Description: | Panel PWB communication error (electronic volume I2C communication error) NACK is received during I2C communication -> retried 5 times -> rebooting command sent -> retried 5 times If NACK is still received. |
| Causes: | Operation PWB. Main PWB |
| Remedy: | Operation PWB 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Operation PWB (YC10) and Main PWB (YC6) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. Main PWB Replace the main PWB. |
| Error code: | 0620 |
| Description: | FAX image DIMM error 1. The Fax image DIMM has not been installed. 2. Fax image DIMM access error. |
| Causes: | DIMM installed incorrectly. Defective main PWB. |
| Remedy: | FAX image DIMM 1. Install the FAX image DIMM supplied in the FAX system onto the main PWB. 2. Firmly install the FAX image DIMM again onto the main board. 3. Check the FAX image DIMM terminals and remove any foreign objects that may be adhered to it. 4. Replace with a new FAX image DIMM. Main PWB. Replace the main PWB. |
| Error code: | 0630 |
| Description: | DMA error DMA transmission of image data does not complete within the specified period of time. |
| Causes: | Poor contact in the connector terminals. Defective main PWB. |
| Remedy: | DP CIS 1. Reconnect the CIS signal line. 2. Confirm that the CIS connector terminals are firmly connected. Insert the connector all the way in. 3. If the wiring is disconnected, shorted or grounded, replace the wiring. DP main PWB Main PWB 1. Confirm that the wiring connector is firmly connectHDD number difference 1. Confirm whether the HDD number is correct in U024_Composition and change it if different. HDD 1piece: Single HDD 2pieces: Multied and, if necessary, connect the connector all the way in. 2. If the wiring is disconnected, shorted or grounded, replace the wiring. Wiring that connects the CIS and the DP controller PWB. Wiring that connects the DP main PWB and the main PWB. 3. Replace the DP main PWB. 4. Replace the main PWB. |
| Error code: | 0640 |
| Description: | Hard disk error The hard disk cannot be accessed. |
| Causes: | Defective hard disk. Defective main PWB. |
| Remedy: | HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Lack of HDD capacity 1. Confirm the total capacity of the HDD if it is more than 320GB. Change the HDD or add it in case of lacking in capacity. Main PWB Replace the main PWB. |
| Error code: | 0650 |
| Display: | Scanner home failure CODE (0650) Turn power off, on |
| Description: | Scanner Home Failure • A low motor lock signal is not detected even after the lapse of a predetermined period of time after the Polygon Motor has been started. • The motor lock signal remains HIGH for a predetermined consecutive period of time while the Polygon Motor remains energized. |
| Causes: | • Engine Control Board, PL13.0.20 • Image Processor Board, PL2.0.4 |
| Remedy: | 1 Check connector P/J2 on the Image Processor Board. Is the connector seated properly? Go to step 2. Reseat the connector. If the problem persists, go to step 2. 2 Replace the Scanner. Does the problem persist? Go to step 3. Complete. 3 Replace the Engine Control Board. Does the problem persist? Go to step 4. Complete. 4 Replace the Power Supply. Complete. |
| Error code: | 0660 |
| Description: | Hard disk encryption key error |
| Causes: | EEPROM. HDD. Main PWB |
| Remedy: | EEPROM 1. Execute U004 if this occurs after the EEPROM has been changed. HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Main PWB Replace the main PWB. |
| Error code: | 0670 |
| Description: | Hard disk overwriting erasure error |
| Causes: | HDD. Main PWB. |
| Remedy: | HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Main PWB Replace the main PWB. |
| Error code: | 0800 |
| Display: | Print Unable 08 Turn the power off and then back on again. |
| Description: | Image processing error JAM010X is detected twice. |
| Causes: | Defective main PWB. |
| Remedy: | Main PWB Replace the main PWB. |
| Error code: | 0830 |
| Description: | FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB |
| Causes: | Defective FAX software. Defective FAX control PWB. |
| Remedy: | FAX software 1. Reinstall the fax software. FAX control PWB 1. Execute initializing by U600.(Refer to the FAX service manual) 2. Replace the FAX control PWB. |
| Error code: | 0840 |
| Description: | Faults of RTC (“Time for maintenance T” is displayed) [Check at power up] The RTC setting has reverted to a previous state. The machine has not been powered for 5 years (compared to the settings stored periodically in the EEPROM). The RTC setting is older than 00:01 on January 1, 2000. [Checked periodically (in 5- minute interval) after powered up] The RTC setting has reverted to a state older than the last time it was checked. 10 minutes have been passed since the previous check. After C840 is detected, the machine enters in disconnection mode after the main power switch has been switched on and off and indicates ‘Maintenance T.’ |
| Causes: | The battery is disconnected from the main PWB Defective main PWB. |
| Remedy: | Battery (main PWB) 1. Make sure that the back-up batteries on the main PWB are not short-circuited. 2. Reset Maintenance T by executing U906. 3. If the same C call is displayed when power is switched on and off, replace the back up battery. 4. If communication error (due to a noise, etc.) is present with the RTC on the main circuit PWB, check the PWB is properly grounded. Main PWB Replace the main PWB |
| Error code: | 0870 |
| Description: | PCFAX control PWB to main PWB high capacity data transfer error High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times. |
| Causes: | Improper installation FAX control PWB. Defective FAX control PWB or main PWB. |
| Remedy: | FAX control PWB 1. Turn the main power swtch off and after 5 seconds, re-mount the FAX controller PWB, then turn power on. 2. Replace the FAX control PWB. HDD Execute U024 to initialize the HDD. Main PWB Replace the main PWB. |
| Error code: | 0920 |
| Description: | Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX control PWB. |
| Causes: | Defective FAX control PWB. |
| Remedy: | FAX control PWB 1. Execute initializing by U600 (Refer to the FAX service manual). 2. Replace the FAX control PWB. |
| Error code: | 0980 |
| Description: | 24 V power down detect If a 24V power disconnection signal is observed and a 12V power disconnection signal is observed simultaneously for one second. |
| Causes: | Defective power source PWB. |
| Remedy: | Power source PWB 1. Check the +24V output is given at YC12- 1 to 3 of the power circuit PWB. 2. Replace the power source PWB |
| Error code: | 1010 |
| Display: | Problem with Printhead L/R Chk printing results |
| Description: | Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1020 |
| Description: | Lift motor 2 error After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 2. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 2 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 2. Lift sensor 2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 2 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor2. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1030 |
| Display: | GARO W1221 |
| Description: | PF lift motor 1 error (paper feeder) After cassette 3 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 1. Replace the PF lift motor 1. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1040 |
| Display: | GL2: W0501 The memory is full. |
| Description: | PF lift motor 2 error (paper feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected 5 times successively. During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found. Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 2 and PF main PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective PF lift motor 2. Replace the PF lift motor 2. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1100 |
| Display: | Prepare for maint cart replacement. |
| Description: | Paper Jam There is paper jammed in the All-In-One. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 1. Defective PF main PWB. |
| Remedy: | Clear the paper jam, and resend the print job. |
| Error code: | 1110 |
| Description: | PF lift motor 2 error (large capacity feeder) After cassette 4 is inserted, PF lift sensor 2 does not turn on within 23 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively. However, the first 1 s after PF lift motor 2 is turned on is excluded from detection. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF lift motor 2. Defective PF main PWB. |
| Remedy: | Paper feeder lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. PF Lift motor 2 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift motor 2 and PF main PWB (YC7) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the PF Lift motor2. PF Lift sensor2 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF Lift sensor 2 and PF main PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the PF Lift sensor 2. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 1800 |
| Description: | Paper feeder communication error A communication error from paper feeder is detected 10 times in succession. |
| Causes: | Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB. |
| Remedy: | Paper feeder Check the wiring connection status with the main unit and, if necessary, try connecting it again. PF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF main PWB (YC13) and Engine PWB (YC19) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the PF main PWB (Refer to the service manual for the paper feeder). Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1900 |
| Description: | Paper feeder EEPROM error When writing the data, read and write data does not match 3 times in succession. |
| Causes: | Defective PF main PWB. Device damage of EEPROM. |
| Remedy: | PF main PWB (EEPROM) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2101 |
| Description: | Developer motor error After developer motor is driven, the ready signal does not turn to L within 2 s. After developer motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective developer motor. Defective engine PWB. |
| Remedy: | Developer unit 1. Check that the developer waste lock has been released and, if not, release the lock. 2. Check that the gears and spiral screw of the developer unit are not damaged. 3. Confirm that the developer roller can rotate. 4. If it won`t rotate, replace the developer unit. Developer motor 1. To check the motor operation, execute DLP(K) by U030. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer motor and Feed PWB 1 (YC8) Feed PWB 1 (YC2) and Engine PWB (YC5) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Developer motor. Engine PWB. 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2102 |
| Description: | Developer motor C error After developer motor C is driven, the ready signal does not turn to L within 5 s. After developer motor C is stabilized, the ready signal is at the H level for 5 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective developer motor C. Defective engine PWB. |
| Remedy: | Developer unit C 1. Check that the developer waste lock has been released and, if not, release the lock. 2. Check that the gears and spiral screw of the developer unit are not damaged. 3. Confirm that the developer roller can rotate. 4. If it won`t rotate, replace the developer unit. Developer motor C 1. To check the motor operation, execute DLP(C) by U030. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer motor C and Motor control PWB (YC7) Motor control PWB (YC3) and Engine PWB (YC9) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Developer motor C. Motor control PWB Replace the Motor control PWB Engine PWB. 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2111 |
| Description: | Developer motor startup error (C,M,Y) After the motor starting, the stable signal is not turned ON within 3 s. |
| Remedy: | Developer unit 1. Check that the developer roller can be rotated by hand, and if it is locked, replace the developer unit. Developer motor 1. Check if the couplings and gears rotate smoothly, and if necessary replace them. 2. Reinsert the connector. 3. Check continuity within the connector wire. If none, replace the wire. Developer motor and Engine relay PWB (YC12) Engine relay PWB (YC1) and Main/ Engine PWB (YC4) 4. Replace the developer motor Engine relay PWB Replace the engine relay PWB. Main/Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the Main/Engine PWB. |
| Error code: | 2112 |
| Description: | Developer motor startup error (M/C/Y) After the motor starts up, the ready signal is not turned ON for continuous 2 s |
| Causes: | Defective connector cable or poor contact in the connector Defective drive transmission system. Defective motor. Defective PWB. |
| Remedy: | Developer unit 1. Check that the developer roller can be rotated by hand, and if it is locked, replace the developer unit. Developer motor 1. Check if the couplings and gears rotate smoothly, and if necessary replace them. 2. Reconnect the connector if its connection is loose. 3. Check the continuity within the connector wire. If none, replace the wire. Developer motor - Engine PWB(YC16): 30 ppm model - Engine PWB(YC23): 35/40 ppm models 4. Replace the developer motor. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 2201 |
| Description: | drum motor steady-state error After drum motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor. Defective engine PWB. |
| Remedy: | Drum unit 1. Confirm that the drum or the drum screw can rotate. 2. If it won’t rotate, replace the drum unit. Drum motor 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. drum motor and Feed PWB 1 (YC9) Feed PWB 1 (YC2) and Engine PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the drum motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2202 |
| Description: | Drum motor C steady-state error The motor revolution fluctuates more than +/-6.2% of the normal revolution for 5s continuously, after the drum motor C has stabilized. The counter achieved by timer capture is less than 2200 in 10 times in a row. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor C. Defective engine PWB. |
| Remedy: | Drum unit 1. Execute U030 Belt Meand (transfer Motor) and check that the drum motor can rotate. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the drum or the drum screw can rotate. 4. If it won’t rotate, replace the drum unit. Drum motor C 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Drum motor C and Motor control PWB (YC4) Motor control PWB (YC3) and Engine PWB (YC9) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum motor C. Motor control PWB Replace the Motor control PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2211 |
| Description: | Drum motor startup error Drum motor is not stabilized within 2 s since the motor is activated. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor K. Defective engine PWB. |
| Remedy: | Drum unit 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the drum or the drum screw can rotate. 3. If it won’t rotate, replace the drum unit. Drum motor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. drum motor and Feed PWB 1 (YC9) Feed PWB 1 (YC2) and Engine PWB (YC5) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the drum motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2212 |
| Description: | Drum motor C startup error Drum motor C is not stabilized within 5 s since the motor is activated. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective drum motor C. Defective engine PWB. |
| Remedy: | Drum unit 1. To check the motor operation, execute U030 Belt Mea nd (transfer motor).. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Decrease Vpp using U100. Change “set ac gain” of U100 from Auto to mode1. 4. Confirm that the drum or the drum screw can rotate. 5. If it won’t rotate, replace the drum unit. Drum motor C 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Drum motor C and Motor control PWB (YC5) Motor control PWB (YC3) and Engine PWB (YC9) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum motor C. Motor control PWB Replace the Motor control PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2300 |
| Description: | Fuser motor error After fuser motor is driven, the ready signal does not turn to L within 2 s. After fuser motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective fuser motor. Defective engine PWB. |
| Remedy: | Fuser motor 1. To check the motor operation, execute U030 Fuser (Fuser motor). 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser motor and Feed PWB 1(YC18) Feed PWB 1(YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the fuser motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Feed PWB 1 Replace the Feed PWB 1. Fuser unit Replace the fuser unit. |
| Error code: | 2310 |
| Description: | Fuser motor startup error Fuser motor is not stabilized within 2 s since the motor is activated. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system. Defective motor. Defective PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser motor and engine PWB (YC3) Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective motor. Replace the fuser motor. Defective PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 2500 |
| Description: | Paper feed motor error After paper feed motor is driven, the ready signal does not turn to L within 2 s. After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective paper feed motor. Defective engine PWB. |
| Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Feed PWB 2(YC2) Feed PWB 2(YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2510 |
| Description: | Paper feed motor startup error Paper feed motor is not stabilized within 1 s since the motor is activated. |
| Causes: | Paper feed motor. Engine PWB |
| Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Engine PWB (YC13) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2550 |
| Description: | Transfer motor error After Transfer motor is driven, the ready signal does not turn to L within 2 s. After Transfer motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective fuser motor. Defective engine PWB. |
| Remedy: | Transfer motor 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Transfer motor and Relay PWB(YC6) Relay PWB(YC5) and Feed PWB 1 (YC13) Feed PWB 1 (YC2) and Engine PWB (YC5) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Transfer motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2560 |
| Description: | Conveying motor startup error Conveying motor is not stabilized within 2 s since the motor is activated. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system. Defective motor Defective PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Conveying motor and engine PWB (YC2) Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective motor. Replace the conveying motor. Defective PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 2600 |
| Description: | PF paper feed motor error (large capacity feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 LCF- Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2610 |
| Description: | PF paper feed motor error (paper feeder) After PF paper feed motor is driven, the ready signal does not turn to L within 2 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective PF paper feed motor. Defective PF main PWB. |
| Remedy: | PF paper feed motor 1. To check the feed unit operation, execute U247 2PF - Motor ON. 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. PF paper feed motor and PF main PWB (YC16) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. PF main PWB Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 2700 |
| Description: | 3-color release motor error When the color release motor is driven, the color release sensor does not turn on/off for 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective color release motor. Defective engine PWB. |
| Remedy: | Color release motor Color release sensor (Intermediate transfer belt unit) 1. To check the motor operation, execute U30 CMY Release. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Intermediate transfer belt unit and Engine PWB (YC3) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Intermediate transfer belt unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 3100 |
| Description: | Scanner carriage error The home position is not correct when the power is turned on, at the end of a reading process of the table and document processor. |
| Causes: | Defective connector cable or poor contact in the connector. Defective home position sensor. Defective scanner motor. Defective ISC PWB. Defective main PWB. |
| Remedy: | The scanner mirror frame is being locked after setup. Check whether the scanner mirror frame has been unlocked and unlock if necessary. Scanner motor 1. To check the scanner motor, execute U073. 2. Move the scanner by the hand to check whether it is unusually difficult to move. 3. Check that the optical wire rope is not disengaged and engage the wire. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Scanner motor and ISC PWB (YC5) ISC PWB (YC3) and Main PWB (YC11) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the scanner motor. Home position sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Home position sensor and ISC PWB (YC8) 3. Replace the home position sensor. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3210 |
| Description: | CIS lamp error When input value at the time of CIS illumination does not exceed the threshold value between 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CIS. Defective DPSHD PWB. Defective DP relay PWB. |
| Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. Execute CCD of U061 lamp check. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CIS and execute U091 and U411. DPSHD PWB Replace the DPSHD PWB. DP relay PWB Replace the DP relay PWB. |
| Error code: | 3220 |
| Description: | CCD lamp activation error The threshold is calculated for colors at initialization and the pixel which does not exceed that value is greater than 1000. |
| Causes: | CIS. ISC PWB. Main PWB. |
| Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. If the LED lamp won’t light, replace the LED PWB and execut U411. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3300 |
| Description: | Optical system (AGC) error One of the gains is FF or 00 during the CCD lamp AGC is being processed. |
| Causes: | Defective connector cable or poor contact in the connector. Defective exposure lamp Defective CCD PWB. Defective ISC PWB. Defective main PWB. |
| Remedy: | LED lamp PWB 1. To check the lamp, execute U061 CCD. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. If the LED lamp won’t light, replace the LED PWB and execut U411. CCD PWB Replace the ISU and execute U411. ISC PWB Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3310 |
| Description: | CIS AGC error After AGC, correct input is not obtained at CIS. |
| Causes: | Defective CIS. Defective DPSHD PWB. Defective DP relay PWB. |
| Remedy: | CIS 1. Execute U906 Separating Operation Release. 2. To check the lamp, execute U061 CCD. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the CIS and execute U091 and U411. DPSHD PWB Replace the DPSHD PWB. |
| Error code: | 3500 |
| Description: | Communication error between scanner and ASIC An error code is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective ISC PWB. Defective main PWB. |
| Remedy: | ISC PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ISC PWB (YC3) and Main PWB (YC11) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the ISC PWB and execute U411. Main PWB Replace the main PWB. |
| Error code: | 3600 |
| Description: | Scanner sequence error |
| Causes: | Defective ISC PWB. |
| Remedy: | ISC PWB 1. Execute U021 memory initializing. 2. Replace the ISC PWB and execute U411. |
| Error code: | 3700 |
| Description: | Scanner device error |
| Causes: | CCD connector inserted incorrectly. |
| Remedy: | CCD (ISU) Since the ISU is mounted with a CCD of different type, install the ISU that matches with the model. |
| Error code: | 3800 |
| Description: | AFE error When writing the data, read and write data does not match 3 times in succession. No response is received in 100 ms from AEF. |
| Causes: | Defective ISC PWB. |
| Remedy: | ISC PWB 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. CCD PWB (YC2) and ISC PWB (YC9) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the ISC PWB and execute U411. CCD PWB Replace the ISU and execute U411. |
| Error code: | 3900 |
| Description: | Backup memory read/write error (ISC PWB) Read and write data does not match. |
| Causes: | Defective backup memory or PWB. |
| Remedy: | Backup memory (ISC PWB) 1. Turn the main power switch off and after 5 seconds, turn it on. 2. Replace the ISC PWB and execute U411. |
| Error code: | 4001 |
| Display: | ERROR E146-4001 Call for service. |
| Description: | Polygon motor synchronization error After polygon motor is driven, the ready signal does not turn to L within 30 s. The polygon motor speed won’t stabilize within 10 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Polygon motor (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor and Engine PWB (YC15) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4002 |
| Display: | Drum End Soon:Y |
| Description: | Polygon motor C synchronization error After polygon motor C is driven, the ready signal does not turn to L within 30 s. The polygon motor speed won’t stabilize within 10 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor C. Defective engine PWB. |
| Remedy: | Polygon motor C (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor C and LSU relay PWB (YC9) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4003 |
| Display: | Drum End Soon:M |
| Description: | Polygon motor M synchronization error After polygon motor M is driven, the ready signal does not turn to L within 30 s. The polygon motor speed won’t stabilize within 10 s |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor M. Defective engine PWB. |
| Remedy: | Polygon motor M (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor M and LSU relay PWB (YC7) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4004 |
| Display: | Drum End Soon:C |
| Description: | Polygon motor Y synchronization error After polygon motor Y is driven, the ready signal does not turn to L within 30 s. The polygon motor speed won’t stabilize within 10 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor Y. Defective engine PWB. |
| Remedy: | Polygon motor Y (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor Y and LSU relay PWB (YC11) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4011 |
| Description: | Polygon motor steady-state error After Polygon motor is stabilized, the ready signal is at the H level for 15 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Polygon motor (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor and Engine PWB (YC15) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4012 |
| Description: | Polygon motor C steadystate error After polygon motor C is stabilized, the ready signal is at the H level for 15 s continuously |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor C. Defective engine PWB. |
| Remedy: | Polygon motor C (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor C and LSU relay PWB (YC9) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4013 |
| Description: | Polygon motor M steadystate error After polygon motor M is stabilized, the ready signal is at the H level for 15 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector Defective polygon motor M. Defective engine PWB. |
| Remedy: | Polygon motor M (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor M and LSU relay PWB (YC7) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB Check the engine software and upgrade to the latest, if necessary. Replace the engine PWB. |
| Error code: | 4014 |
| Description: | Polygon motor Y steadystate error After polygon motor Y is stabilized, the ready signal is at the H level for 15 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor Y. Defective engine PWB. |
| Remedy: | Polygon motor Y (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor Y and LSU relay PWB (YC11) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4101 |
| Description: | BD initialization error K After Polygon motor is driven, the BD signal is not detected for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB. Defective engine PWB. |
| Remedy: | PD PWB K (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4102 |
| Description: | BD initialization error C After polygon motor C is driven, the BD signal is not detected for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB C. Defective engine PWB. |
| Remedy: | PD PWB C (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC10) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4103 |
| Description: | BD initialization error M After polygon motor M is driven, the BD signal is not detected for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB M. Defective engine PWB. |
| Remedy: | PD PWB M (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC8) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4104 |
| Description: | BD initialization error Y After polygon motor Y is driven, the BD signal is not detected for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB Y. Defective engine PWB. |
| Remedy: | PD PWB Y (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC12) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4201 |
| Display: | Replace Drum:BK |
| Description: | BD steady-state error K The BD signal is not detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB. Defective engine PWB. |
| Remedy: | PD PWB K (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, shorted or grounded, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4202 |
| Display: | Replace Drum:Y |
| Description: | BD steady-state error C The BD signal is not detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB C. Defective engine PWB. |
| Remedy: | PD PWB C (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC10) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4203 |
| Display: | Replace Drum:M |
| Description: | BD steady-state error M The BD signal is not detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB M. Defective engine PWB. |
| Remedy: | PD PWB M (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC8) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4204 |
| Display: | Replace Drum:C |
| Description: | BD steady-state error Y The BD signal is not detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB Y. Defective engine PWB |
| Remedy: | PD PWB Y (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC12) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4600 |
| Display: | Maintenance Replace Laser |
| Description: | LSU cleaning motor error After LSU cleaning motor is driven, the ready signal does not turn to L within 2 s. After LSU cleaning motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective LSU cleaning motor. Defective engine PWB. |
| Remedy: | LSU cleaning motor 1. Execute LSU cleaning using Adjustment/Maintenance of the system menu. 2. Rotate the drive gear and the cleaning spiral by the hand and check that they are not unusually loaded, and replace if it is damaged. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. LSU cleaning motor and Engine PWB (YC21) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the LSU cleaning motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6000 |
| Description: | Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6030 |
| Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6040 |
| Description: | Fuser heater error Input from fuser center thermistor 1 is abnormal value continuously for 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Center thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6050 |
| Description: | Abnormally low fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up, during ready or during print. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 1. Defective fuser heater. Defective engine PWB. |
| Remedy: | Power source 1. Check that the operating voltage falls within +/-10%. 2. Check no voltage drop is caused. The heater is deactivated at 70V or lower. 3. Relocate the AC outlet that supplies power. Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 1. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6120 |
| Description: | Abnormally high fuser press thermistor 5 temperature Fuser press thermistor 5 detects a temperature higher than 190°C/ 374°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 5. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6130 |
| Description: | Broken fuser press thermistor 5 wire The input from the fuser press thermistor 5 has been less than 30°C/ 86°F (A/D: greater thann992) for 60 seconds continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 5 wire. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) Fuser IH PWB(YC4) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB(YC4) and Engine PWB (YC26) 2. Replace the fuser IH PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. |
| Error code: | 6150 |
| Description: | Abnormally low fuser press thermistor 5 temperature Fuser press thermistor 5 detects a temperature lower than 30°C/ 86°F for 1 s after warming up. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 5. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB( YC4) and Engine PWB (YC26) 2. Replace the fuser IH PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. |
| Error code: | 6200 |
| Display: | No Drum Unit Install the Drum Unit. |
| Description: | Broken fuser edge heater wire Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up. The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser center thermistor 1 1. Replace the Fuser unit. |
| Error code: | 6220 |
| Description: | Abnormally high fuser edge thermistor temperature Fuser thermistor 2 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 2. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6230 |
| Description: | Broken fuser edge thermistor wire The Input signal from the fuser thermistor 2 is 992 or more (A/D value) continuously for 1 s when the temperature at the fuser thermistor 1 is higher than 100°C/212°F. Fuser thermistor 2 detects a lower then 50°C/122°F for 15s during warming up. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 2 wire. Fuser thermostat triggered. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6250 |
| Description: | Abnormally low fuser edge thermistor temperature Fuser thermistor 2 detects a temperature lower than 100°C/212°F for 1 s during ready or print. |
| Causes: | Deformed connector pin. Defective triac. Defective fuser thermistor 2. Defective fuser IH. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. 2. Fuser unit and Engine PWB (YC26) If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6410 |
| Description: | Fuser unit type mismatch problem Absence of the fuser unit is detected. |
| Causes: | Fuser unit connector inserted incorrectly. Different type of the fuser unit is installed. |
| Remedy: | Fuser unit connector inserted incorrectly. Reinsert the fuser unit connector if necessary. Different type of the fuser unit is installed. Install the correct fuser unit. |
| Error code: | 6600 |
| Description: | Fuser belt rotation error A belt rotating pulse is not received for 1 s. (Engine CPU) |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser belt sensor. Defective engine PWB. |
| Remedy: | Fuser motor 1. To check the motor operation, execute U030 Fuser. 2. Check that the drive gear can rotate and not heavily loaded and, if necessary, apply grease to the axle holder and gears. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser motor and Feed PWB (YC18) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the fuser motor. Fuser belt sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6710 |
| Description: | Fuser IH PWB CPU reset error Watch doc timer has been overflowed. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6720 |
| Description: | Fuser IH belt rotation error While driving, the pulse count is less than 3 for 2 seconds during the input to the rotation pulse signal is 200 msec. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser belt sensor. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Fuser motor 1. To check the motor operation, execute U030 Fuser. 2. Check that the drive gear can rotate and not heavily loaded and, if necessary, apply grease to the axle holder and gears. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser motor and Feed PWB (YC18) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the fuser motor. Fuser belt sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB(YC4) and Engine PWB (YC26) 2. Replace the fuser IH PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6730 |
| Description: | Abnormally high fuser IH PWB temperature 1 (IGBT1) The input detect temperature is higher than 115°C/ 221 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB ( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6740 |
| Description: | Abnormally high fuser IH PWB temperature 2 (IGBT2) The input detect temperature is higher than 115°C/ 221 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB ( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6750 |
| Description: | Fuser IH output over-current error The output current of IH CPU is higher than 110 A for 10 ms in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) Fuser IH PWB( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6760 |
| Description: | Fuser IH input over-current error The input current of IH CPU is higher than 20A (100V/120V), 10A (200V) for 100 ms in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6770 |
| Description: | Fuser IH low electric power error Less than 0.6 times of the preset power is detected for 120 ms in succession after the IH heater remote has turned on. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Fuser IH PWB (YC6) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser IH unit. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser IH PWB. Fuser IH unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH unit and Fuser IH PWB (YC9 and 10) Fuser IH PWB( YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser IH unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6930 |
| Description: | Fuser rear fan motor error When the fuser rear fan motor is driven, alarm signal is detected for 5 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser edge fan motor 2. Defective engine PWB. |
| Remedy: | Fuser rear fan motor 1. To check the fan motor operation, execute U037 Fuser Cooling. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser rear fan motor and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the fuser rear fan motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6950 |
| Description: | Fuser IH PWB communication error No response is received in 30 ms since a command is sent to IHCPU. A checksum error is detected 10 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC9) and Feed PWB 1(YC4) Power source PWB (YC3) and Fuser IH PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. If the +24V output is not given by the power source PWB (YC9), replace the power source PWB. Feed PWB 1 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and Fuser IH PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. If the +24V output is not given by the feed PWB1 (YC27), replace the feed PWB1. Fuser IH PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser IH PWB(YC4) and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser IH PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6990 |
| Description: | Fuser power supply incompatibility Information won’t match between the engine backup and the fuser IH PWB. |
| Causes: | Defective fuser IH PWB. Defective engine PWB. |
| Remedy: | Differences in settings after initialization When this has happened after initialization using U021, make settings identical with the voltages on the IH PWB using U169. Fuser IH PWB Replace with a fuser IH PWB specifically designed with the standard voltage. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7101 |
| Description: | Toner sensor error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective toner sensor. Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the Developer unit are not damaged and the spiral can rotate. 5. Replace the Developer unit. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7102 |
| Description: | Toner sensor C error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor C 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor C and Front PWB (YC13) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit C are not damaged and the spiral can rotate. 5. Replace the Developer unit C. Toner motor C 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor C and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor C. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7103 |
| Description: | Toner sensor M error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor M 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor M and Front PWB (YC11) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit M are not damaged and the spiral can rotate. 5. Replace the Developer unit M. Toner motor M 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor M and and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor M. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7104 |
| Description: | Toner sensor Y error Sensor output value of 60 or less or 944 or more continued for 3 s. |
| Causes: | Defective connector cable or poor contact in the connector Defective engine PWB. |
| Remedy: | Failure of locking the developer waste slot at setup. If an abnormal noise is heard, check that the developer ejection outlet is released and, if not, release the outlet. Toner sensor Y 1. Check the toner sensor output by U155. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner sensor Y and Front PWB (YC15) Front PWB (YC2) and Engine PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Check that the gears of the developer unit Y are not damaged and the spiral can rotate. 5. Replace the Developer unit Y. Toner motor Y 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor Y and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor Y. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7401 |
| Description: | Developer unit type mismatch error Improper adaptation of the machine and developer unit is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
| Remedy: | Different type of the developer unit is installed. Install the developer unit of the correct type. Developer unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
| Error code: | 7402 |
| Description: | Developer unit C type mismatch error Absence of the developer unit C is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit C and front PWB (YC13) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
| Error code: | 7403 |
| Description: | Developer unit M type mismatch error Absence of the developer unit M is detected. |
| Causes: | Defective connector cable or poor contact in the connector Different type of the developer unit is installed |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit M and front PWB (YC11) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
| Error code: | 7404 |
| Description: | Developer unit Y type mismatch error Absence of the developer unit Y is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit Y and front PWB (YC15) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
| Error code: | 7411 |
| Description: | Drum unit type mismatch error Improper adaptation of the machine and developer unit is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the drum unit is installed. |
| Remedy: | Different type of the drum unit is installed. Install the drum unit of the correct type. Drum unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Drum unit and Front PWB (YC6) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
| Error code: | 7412 |
| Description: | Drum unit type Mismatch error (Cyan) Improper adaptation of the main unit and drum unit is detected. |
| Causes: | Drum unit C |
| Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7413 |
| Description: | Drum unit type Mismatch error (Magenta) Improper adaptation of the main unit and drum unit is detected. |
| Causes: | Drum unit M |
| Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7414 |
| Description: | Drum unit type Mismatch error (Yellow) Improper adaptation of the main unit and drum unit is detected. |
| Causes: | Drum unit Y |
| Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7420 |
| Description: | Transfer belt unit type mismatch problem Absence of the transfer belt unit is detected. |
| Causes: | Transfer belt unit connector inserted incorrectly. Different type of the transfer belt unit is installed. Defective PWB. |
| Remedy: | Transfer belt unit connector inserted incorrectly. Reinsert the transfer belt unit connector if necessary. Different type of the transfer belt unit is installed. Install the correct transfer belt unit. Defective PWB. Replace the engine PWB check for correct operation. |
| Error code: | 7601 |
| Description: | ID sensor 1 error [Front] Dark potential error FrontDarkP and FrontDarkS are greater than 0.80V. Light potential error FrontBrightS is smaller than FrontDarkS. FrontBrightP is smaller than [FrontDarkP + 0.5V]. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | ID sensor1 1. Execute U464 Calib for setting ID compensation operation and check the displayed values by U465 Boas Calib for ID compensation reference. 2. Clean the ID sensor on its surface. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ID sensor 1 (front) and relay PWB (YC10) Relay PWB (YC1) and Feed PWB 1 (YC14) Feed PWB 1 (YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. Feed PWB 1 Replace the Feed PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7602 |
| Description: | ID sensor 2 error [Rear] Dark potential error RearDarkP and RearDarkS are greater than 0.80V. Light potential error RearBrightS is smaller than RearDarkS. RearBrightP is smaller than [RearDarkP + 0.5V]. |
| Causes: | Defective connector cable or poor contact in the connector. Defective engine PWB. |
| Remedy: | ID sensor 2 1. Execute U464 Calib for setting ID compensation operation and check the displayed values by U465 Boas Calib for ID compensation reference. 2. Clean the ID sensor on its surface. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. ID sensor2 (rear) and relay PWB (YC10) Relay PWB (YC1) and Feed PWB 1 (YC14) Feed PWB 1 (YC1) and Engine PWB (YC6) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. Feed PWB 1 Replace the Feed PWB 1. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7611 |
| Description: | Bias calibration reading value error (Black) During the calibration, the ID sensor cannot read a patch density on the primary transfer belt normally |
| Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
| Remedy: | Primary transfer belt ID sensor 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7612 |
| Description: | Bias calibration reading value error (Cyan) During the calibration, the ID sensor cannot read a patch density on the primary transfer belt normally. |
| Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
| Remedy: | Primary transfer belt ID sensor 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7613 |
| Description: | Bias calibration reading value error (Magenta) During the calibration, the ID sensor cannot read a patch density on the primary transfer belt normally. |
| Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
| Remedy: | Primary transfer belt ID sensor 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7614 |
| Description: | Bias calibration reading value error (Yellow) During the calibration, the ID sensor cannot read a patch density on the primary transfer belt normally. |
| Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
| Remedy: | Primary transfer belt ID sensor 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7620 |
| Description: | Color Registration timing of detection Color patches printed on the primary transfer belt are not within the ID sensor readable range. Or the poor density occurs. |
| Causes: | Primary transfer unit ID sensor Drum unit Developer unit LSU Main/Engine PWB |
| Remedy: | Primary transfer belt ID sensor LSU 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Execute [Calibration] using [Adjustment/Maintenance] of the system menu. 3. Check the occurrence of this service call error in the Event Log. 4. When the same service call error is detected again, clean if there is any dirt or stains on the primary transfer belt or the ID sensor surface. 5. Check whether or not the ID sensor shutter is open, by opening and closing the paper tray. 6. If not corrected, replace the primary transfer unit. 7. After performing the test print, if the poor density occurs, check whether there is any failure in the drum unit, developer unit, LSU. 8. When checking the printing position of the color, if any color shift occurs, re-install the LSU and the drum unit. 9. If not corrected, replace the LSU. Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7800 |
| Description: | Broken outer temperature sensor wire The device did not respond for more than 5 ms during reading, in 5 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor. Defective engine PWB. |
| Remedy: | Outer temperature sensor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Outer temperature sensor and Front PWB (YC8) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Outer temperature sensor. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7810 |
| Description: | Short-circuited outer temperature sensor 1 The sensor input sampling is less than 0. |
| Causes: | Defective connector cable or poor contact in the connector. Defective outer temperature sensor 1. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Outer temperature sensor and front PWB (YC16) Front PWB (YC2) and engine PWB (YC10) Defective outer temperature sensor. Replace outer temperature sensor. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 7901 |
| Description: | Drum EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB. |
| Remedy: | DR PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DR PWB and Front PWB (YC6) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7902 |
| Description: | Drum C EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB C. |
| Remedy: | DR PWB- C 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DR PWB- C and Front PWB (YC12) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit C. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7903 |
| Description: | Drum M EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB M. |
| Remedy: | DR PWB- M 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DR PWB- M and Front PWB (YC10) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit M. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7904 |
| Description: | Drum Y EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drum PWB Y. |
| Remedy: | DRPWB- Y 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DRPWB- Y and Front PWB (YC14) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Drum unit Y. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7911 |
| Description: | Developer unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer unit. |
| Remedy: | Developer unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7912 |
| Description: | Developer unit C EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer unit C. |
| Remedy: | Developer unit C 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit C and Front PWB (YC13) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit C. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7913 |
| Description: | Developer unit M EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer unit M. |
| Remedy: | Developer unit M 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit M and Front PWB (YC11) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit M. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7914 |
| Description: | Developer unit Y EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively. |
| Causes: | Defective connector cable or poor contact in the connector. Defective developer unit Y. |
| Remedy: | Developer unit Y 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit Y and Front PWB (YC15) Front PWB (YC2) and Engine PWB (YC10) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Developer unit Y. Front PWB Replace the front PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 8010 |
| Description: | Punch motor error 1 When the punch motor is driven, punch home position sensor does not turn on within 200 ms. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch home position sensor. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch home position sensor 1. Execute U241 Punch - Punch HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch home position sensor and Punch PWB (YC8) 4. Replace the Punch home position sensor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8020 |
| Description: | Punch motor error 2 Home position is not obtained in 3 s after home position is initialized or in standby. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8030 |
| Description: | Punch motor error 3 Home position does not turn from On to Off in 50 ms after home position has been initialized. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch motor. Defective PWB. |
| Remedy: | Punch motor 1. Execute U240 Motor - Punch to check the finisher operation. 2. Manipulate the punch up and down to check it can smoothly move up and down. 3. Check that the drive from the motor reaches the punch cam. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch motor and Punch PWB (YC4) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch motor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8090 |
| Description: | DF paddle motor error When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF paddle sensor. Defective DF paddle motor. Defective DF main PWB. |
| Remedy: | DF paddle motor 1. Execute U240 Motor - Beat to check the finisher operation. 2. Check that the paddle can rotate. 3. Check that the drive from the motor reaches the paddle. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF paddle motor and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF paddle motor. DF paddle sensor 1. Execute U241 Finisher - Bundle Eject HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF paddle sensor and DF main PWB (YC22) 4. Replace the DF paddle sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8100 |
| Description: | DF eject release motor error When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF bundle discharge sensor. Defective DF eject release motor. Defective DF main PWB. |
| Remedy: | DF eject release motor DF bundle discharge unit sensor 1. Execute U240 Motor - Eject Unlock (Full) to check the finisher operation. 2. Check that the eject guide of the process tray is opened and, if not, correct the guide. 3. Check that the drive from the motor reaches the eject guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF bundle discharge unit sensor and DF main PWB (YC22) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF eject release motor. DF bundle discharge unit sensor 1. Execute U241 Finisher - Bundle Eject HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF bundle discharge unit sensor and DF main PWB (YC22) 4. Replace the DF bundle eject unit sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8140 |
| Description: | DF tray motor error 1 When the main tray has ascended, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF Main PWB(YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF Main PWB(YC22) DF tray upper surface sensor and DF Main PWB(YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8150 |
| Description: | DF tray motor error 2 When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective sensor. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 1 DF tray upper surface sensor 1. Execute U241 Finisher - Tray U-Limit, Tray Top to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 1 and DF main PWB (YC22) DF tray upper surface sensor and DF main PWB (YC21,YC13) 4. Replace the DF tray sensor 1 or DF tray upper surface sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8160 |
| Description: | DF tray motor error 3 When the main tray has descended, DF tray sensor 4 does not turn on within 20 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF tray sensor 3. Defective DF tray motor. Defective DF main PWB. |
| Remedy: | DF tray motor 1. Execute U240 Motor - Tray to check the finisher operation. 2. Manipulate the main tray up and down to check it is smoothly operable. 3. Check that the drive from the motor reaches the main tray. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray motor and DF main PWB (YC16) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF tray motor. DF tray sensor 4 1. Execute U241 Finisher - Tray Middle to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF tray sensor 4 and DF main PWB (YC23) 4. Replace the DF tray sensor 4. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8170 |
| Description: | DF side registration motor 1 error 1 When initial operation, DF side registration sensor 1 does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8180 |
| Description: | DF side registration motor 1 error 2 JAM6810 (jam in front of width alignment) is detected twice. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 1. Defective DF side registration motor 1. Defective DF main PWB. |
| Remedy: | DF side registration motor 1 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the front side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the front side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 1 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 1. DF side registration sensor 1. 1. Execute U241 Finisher - Width Front to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 1. and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF side registration sensor 1. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8190 |
| Description: | DF side registration motor 2 error 1 When initial operation, DF side registration sensor 2 does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 2. Defective DF side registration motor 2. Defective DF main PWB. |
| Remedy: | DF side registration motor 2 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the rear side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the rear side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 2 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 2. DF side registration sensor 2 1. Execute U241 Finisher - Width tail HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 2 and DF main PWB (YC22) 4. Replace the DF side registration sensor 2. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8200 |
| Description: | DF side registration motor 2 error 2 JAM6910 (jam in rear of width alignment) is detected twice. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF side registration sensor 2. Defective DF side registration motor 2. Defective DF main PWB. |
| Remedy: | DF side registration motor 2 1. Execute U240 Motor - Width Test to check the finisher operation. 2. Manipulate the rear side registration guide back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the rear side registration guide. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration motor 2 and DF main PWB (YC15) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF side registration motor 2. DF side registration sensor 2 1. Execute U241 Finisher - Width tail HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF side registration sensor 2 and DF main PWB (YC22) 4. Replace the DF side registration sensor 2. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8210 |
| Description: | DF slide motor error When initial operation, DF staple sensor does not turn on within 3 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF slide motor. Defective DF main PWB. |
| Remedy: | DF slide motor 1. Execute U240 Motor - Staple Move to check the finisher operation. 2. Manipulate the staple unit back and forth to check it is smoothly operable. 3. Check that the drive from the motor reaches the staple unit. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF slide motor and DF main PWB (YC12) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DF slide motor. DF staple sensor 1. Execute U241 Finisher - Width Staple HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF staple sensor and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF staple sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8230 |
| Description: | DF staple motor error 1 Staple JAM (DF) has been detected twice in a row. (The second JAM detection condition fullfilled with the home position did not detected in 600 ms after the motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple sensor. Defective DF staple motor. Defective DF main PWB. |
| Remedy: | DF staple motor 1. Remove the staple unit and check that stapling is possible without a jam. 2. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Staple unit and DF main PWB (YC17) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the staple unit. (Refer to the service manual for the document finisher). DF staple sensor Replace the staple unit. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8240 |
| Description: | DF staple motor error 2 Staple JAM (DF) has been detected twice in a row. (The second JAM detection condition fullfilled with a lock detection signal maintained 1 V for 500 ms continuously, while the stapler motor was driven.) |
| Causes: | Defective connector cable or poor contact in the connector. Defective DF staple motor. Defective DF main PWB. |
| Remedy: | DF staple motor 1. Remove the staple unit and check that stapling is possible without a jam. 2. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Staple unit and DF main PWB (YC17) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the staple unit. (Refer to the service manual for the document finisher). DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8260 |
| Description: | DF middle motor home position error DF paddle sensor is not turned on within 1s after driving the DF middle motor. |
| Causes: | DF middle motor. DF paddle sensor. DF main PWB |
| Remedy: | DF middle motor 1. Execute U240 Motor - Middle(H)(L). 2. Check that the drive from the motor reaches the paddle. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF middle motor and DF main PWB (YC12) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF middle motor. DF paddle sensor 1. Execute U241 Finisher - Lead Paddle to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF paddle sensor and DF main PWB (YC22) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DF paddle sensor. DF main PWB Replace the DF main PWB (Refer to the service manual for the document finisher). |
| Error code: | 8410 |
| Description: | Punch slide motor error 1 The punch slide sensor won’t turn On when home position has been moved by 30 mm. |
| Causes: | Defective connector cable or poor contact in the connector. Defective slide sensor. Defective punch slide motor. Defective PWB. |
| Remedy: | Punch slide motor 1. Execute U240 Booklet - Punch Move to check the finisher operation. 2. Manipulate the punch slide part of the punch unit back and forth to check it can smoothly move. 3. Check that the drive from the motor reaches punch part. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide motor and Punch PWB (YC3) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch slide motor. Punch slide sensor 1. Execute U241 Punch - Punch HP to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide sensor and Punch PWB (YC6) 4. Replace the punch slide sensor. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8420 |
| Description: | Punch slide motor error 2 In detection of paper edges, the paper edge cannot be detected in 30 mm move. |
| Causes: | Defective connector cable or poor contact in the connector. Defective punch slide motor. Defective PWB. |
| Remedy: | Punch slide motor 1. Execute U240 Booklet - Punch Move to check the finisher operation. 2. Manipulate the punch slide part of the punch unit back and forth to check it can smoothly move. 3. Check that the drive from the motor reaches punch part. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch slide motor and Punch PWB (YC3) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the punch slide motor. Punch paper edge sensor 1,2 1. Execute U241 Punch - Edge Face 1,2,3,4 to check the finisher switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch paper edge sensor 1,2 and Punch PWB (YC5,YC7) 4. Replace the punch paper edge sensor 1,2. Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. Replace the Punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8430 |
| Description: | Punch unit communication error Communication with the punch unit is not possible. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | Punch PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Punch PWB (YC1) and DF main PWB (YC7) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Punch PWB. DF main PWB Replace the DF main PWB |
| Error code: | 8800 |
| Description: | Document finisher main program error Document finisher main program error at power up. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PWB. |
| Remedy: | DF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF main PWB (YC4) and Engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the DF main PWB Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 8900 |
| Description: | Document finisher backup error Read and write data does not match 3 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Improper installation EEPROM. Defective DF main PWB. |
| Remedy: | DF main PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DF main PWB (YC4) and Engine PWB (YC18) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the DF main PWB |
| Error code: | 8990 |
| Description: | Finisher setup error In case the bridge (AK) is not installed while the DF is connected. (35/40 ppm model only) |
| Causes: | Bridge unit Document finisher. DF main PWB. Engine PWB |
| Remedy: | Finisher 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. DF main PWB - Engine PWB(YC24): 30 ppm model - Engine PWB(YC31): 35/40 ppm models 2. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. DF main PWB 1. Check EEPROM mount and correct it. 2. Replace the DF main PWB. |
| Error code: | 9000 |
| Description: | Document processor communication error Communication with the document processor is not possible. |
| Causes: | Defective connector cable or poor contact in the connector Defective PWB. |
| Remedy: | DP main PWB 1. Check that the versions of the main unit firmware and the DP firmware are identical. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP main PWB(YC1) and ISC PWB(YC12) ISC PWB (YC3) and Main PWB (YC11) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the DP main PWB ISC PWB Replace the ISC PWB. |
| Error code: | 9010 |
| Description: | Coin vender communication error A communication error from coin vender is detected 10 times in succession. |
| Causes: | Defective connector cable or poor contact in the connector. Data setup failure. Defective coin vender control PWB. Defective PWB. |
| Remedy: | U206 setting Set maintenance mode U206 to off when a coin vender is not installed. Coin vender control PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Coin vender control PWB and Engine PWB (YC23) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Coin vender control PWB. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 9040 |
| Description: | DP lift motor going up error When the DP lift motor is driven, DP lift sensor 1 does not turn on within 1500 pulse. (Three recovery times.) The above has been detected 5 times. * : The number of detection should be weighted with one for the rise at job start and two for the irregular rise during transporting. The accumulated number must be cleared at completion of a normal rise. The default threshold is 5. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DP lift sensor 1. Defective DP lift motor. Defective DP main PWB. |
| Remedy: | DP lift motor 1. Execute U906 Separating Operation Release. 2. Execute U243 Lift Motor to check the DP motor operation. 3. Check that the original document lift guide can move upwards. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift motor and DP main PWB (YC5) 5. If the wiring is disconnected, shorted or grounded, replace the wiring. 6. Replace the DP lift motor. DP lift sensor 1 1. Execute U244 Lift L-Limit to check DP switch. 2. Check that the sensor and its mounting bracket are correctly positioned. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift sensor 1 and DP main PWB (YC4) 4. Replace the DP lift sensor 1. DP main PWB Replace the DP main PWB |
| Error code: | 9050 |
| Description: | DP lift motor going down error When the DP lift motor is driven, DP lift sensor 2 does not turn on within 1500 pulse. (Three recovery times.) The above has been detected 1 times. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DP lift sensor 2. Defective DP lift motor. Defective DP main PWB. |
| Remedy: | DP lift motor 1. Execute U906 Separating Operation Release. 2. Execute U243 Lift Motor to check the DP motor operation. 3. Check that the original document lift guide can move downwards. 4. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift motor and DP main PWB (YC5) If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the DP lift motor. DP lift sensor 2 1. Execute U244 Lift L-Limit to check DP switch. 2. Confirm that the DP lift sensor 2 has been firmly fitted. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP lift sensor 2 and DP main PWB (YC2) 4. Replace the DP lift sensor2. DP main PWB Replace the DP main PWB |
| Error code: | 9060 |
| Description: | DP EEPROM error Mismatch of reading data from two locations occurs 3 times successively. Mismatch between writing data and reading data occurs 3 times successively. |
| Causes: | Defective DP main PWB. Device damage of EEPROM. |
| Remedy: | DP main PWB 1. Execute U906 Separating Operation Release. 2. Confirm that the EEPROM has been properly installed. 3. Replace the DP main PWB Device damage of EEPROM Contact the Service Support. |
| Error code: | 9070 |
| Description: | Communication error between DP and SHD A communication error is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective DPSHD PWB. |
| Remedy: | DP SHD PWB 1. Execute U906 Separating Operation Release. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. DP SHD PWB (YC1) and DP main PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the DP SHD PWB. |
| Error code: | 9080 |
| Description: | LED fault detection A block is existent below a peak which was obtained by activating the LEDs in the four CIS blocks at power on, which is less than 80hex. |
| Causes: | Defective connector cable or poor contact in the connector. Defective CIS Defective DPSHD PWB. |
| Remedy: | DP CIS 1. Execute CIS automatic original document alignment by U411. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. CIS and DP SHD PWB (YC2) DP SHD PWB (YC1) and DP main PWB (YC10) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the CIS and execute U411. DP SHD PWB Replace the DP SHD PWB. |
| Error code: | 9100 |
| Description: | Coin vender control PWB error Communication error has been detected at the coin mec of the coin vender control PWB. |
| Causes: | Defective coin vender control PWB. |
| Remedy: | Coin vender control PWB Replace the coin mec. |
| Error code: | 9110 |
| Description: | Coin vender rejector error Communication error has been detected in connection with the coin mec and the rejector. |
| Causes: | Rejector installed incorrectly. Defective rejector. |
| Remedy: | Rejector 1. Check that the rejector is firmly installed and, if not, install firmly. 2. Replace the rejector. |
| Error code: | 9120 |
| Description: | Sensor error in coin vender change (Yen 10) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Coin jam in the change tube Check visually and remedy. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9130 |
| Description: | Sensor error in coin vender change (Yen 50) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Coin jam in the change tube Check visually and remedy. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9140 |
| Description: | Sensor error in coin vender change (Yen 100) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Coin jam in the change tube Check visually and remedy. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9150 |
| Description: | Sensor error in coin vender change (Yen 500) Change is empty despite change is enough. |
| Causes: | Coin jam in the change tube Poor contact in the connector. Defective change empty sensor. Defective coin vender control PWB. |
| Remedy: | Change tube Check no exchange jam is observed at the outlet and, if necessary, repair it. Contact in the connector Check the connection of the empty change sensor. Change empty sensor Replace the coin mec. Coin vender control PWB Replace the coin mec. |
| Error code: | 9160 |
| Description: | Coin vender pay-out error Coin is paid out despite the pay-out motor is determined not active. |
| Causes: | Defective pay-out motor. |
| Remedy: | Pay-out motor Replace the coin mec. |
| Error code: | 9170 |
| Description: | Coin vender pay-out sensor error Coin is paid out despite the pay-out motor is determined not active. |
| Causes: | Change jam at the pay-out. Defective pay-out motor. Defective pay-out sensor. |
| Remedy: | Pay-out area Check no exchange jam is observed at the outlet and, if necessary, repair it. Pay-out motor Replace the coin mec. Pay-out sensor Replace the coin mec. |
| Error code: | 9500 |
| Description: | ISC PWB error A |
| Causes: | Main PWB. ISC PWB. |
| Remedy: | Main PWB ISC PWB 1. Reinsert the connector if its connection is loose. Main PWB (YC25) and ISC PWB (YC4) 2. Replace the main PWB. 3. Replace the ISC PWB 4. Contact the Service Support. |
| Error code: | 9510 |
| Description: | ISC PWB error B |
| Causes: | Main PWB. DP SHD PWB. |
| Remedy: | Main PWB DP SHD PWB 1. Reinsert the connector if its connection is loose. DP relay PWB (YC2) and DP SHD PWB (YC3) 2. Replace the main PWB. 3. Replace the DP SHD PWB. 4. Contact the Service Support. |
| Error code: | 9520 |
| Description: | ISC PWB error C |
| Causes: | Main PWB. ISC PWB. |
| Remedy: | Main PWB ISC PWB 1. Reinsert the connector if its connection is loose. Main PWB (YC25) and ISC PWB (YC4) 2. Replace the main PWB. 3. Replace the ISC main PWB 4. Contact the Service Support. |
| Error code: | 9530 |
| Description: | Machine No.backup error C |
| Causes: | IPU PWB error |
| Remedy: | Contact the Service Administrative Division. |
| Error code: | 9540 |
| Description: | Backup data error The machine may not be recovered or may have trouble in its function with changes of the internal data when replacing some the parts at the same time. |
| Causes: | PWBs |
| Remedy: | Reattach the parts below in case of replacing 2 or more of them at the same time. Affected parts : Memory, PWBs * Do not replace two or more of the parts at the same time. * And, do not either execute the following works when replacing the above parts. Replace the drum unit or the developing unit. Replace the drum unit for the one color with another in the same machine. |
| Error code: | 9550 |
| Description: | Machine No.backup error E |
| Causes: | IPU PWB error |
| Remedy: | Contact the Service Administrative Division. |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 ... F013 |
| Description: | Main PWB checksum error |
| Causes: | Defective main PWB. |
| Remedy: | 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. If not corrected, replace the main PWB. |
| Error code: | F020 ... F023 |
| Description: | System memory error Controller detection error |
| Causes: | Defective main PWB. |
| Remedy: | 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. If not corrected, replace the main PWB. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F041 |
| Description: | Over than available setting number tray detection error |
| Causes: | Over than available setting number tray is installed. |
| Remedy: | Remove the available setting number tray. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F051 |
| Description: | Scanner engine program error |
| Causes: | The scanner program cannot start up |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The scanner engine RAM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the SSD The SSD is not properly attached. Reattach the SSD. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
Парткод
Название
Kyocera Блок фотобарабана в сборе
Kyocera Блок проявки голубой
Kyocera Блок проявки черный
Kyocera Блок проявки пурпурный
Kyocera Блок проявки желтый
Kyocera Блок термозакрепления
Kyocera Сервисный комплект черный
Kyocera Сервисный комплект цветной
Kyocera Тонер-картридж голубой
Kyocera Тонер-картридж черный
Kyocera Тонер-картридж пурпурный
Kyocera Тонер-картридж желтый
