Kyocera FS-7000

Рейтинг

Снят с производства

Тип устройства

Принтер

Технология печати

лазерная

Макс. формат

Число страниц в месяц

100000

Цветность печати

черно-белая

Общие характеристики
Макс. формат	A3
Технология печати	лазерная
Цветность печати
Тип	лазерный/светодиодный
Число страниц в месяц	100 000
Область применения	большой офис
Сканер
Печать фотографий
Копир
Тип устройства	Принтер
Принтер
Двусторонняя печать
Прямая печать
Макс, разрешение для ч/б печати
По Y	600
По X	600
Расходные материалы
Ресурс ч/б картриджа/тонера	33 000
Печать на:
Фотобумаге
Этикетках
Пленках
Языки управления
PostScript
Лотки
Подача бумаги
Стандартная	1 000
Вывод бумаги
Стандартный	500
Интерфейсы
Инфракрасный порт
Ethernet (RJ-45)
LPT
USB
Память/Процессор
Объем памяти	8
Макс, объем памяти	72
Дополнительная информация
Поддержка ОС
Linux
DOS
Windows
Mac OS
Уровень шума
При работе	38
Габариты
Вес	38
Глубина	566
Высота	560
Ширина	345

Коды ошибок

B1 ... B6

D0 ... D4

Описание

Парткод

Название

Kyocera Блок фотобарабана

Kyocera Сервисный комплект

Kyocera Тонер-картридж черный

Error code:	A1
Display:	Cover is Open
Description:	Jam at Door A
Causes:	• Tray 1 (MPT) Feed Roller, PL10.1.53 • Tray 1 (MPT) Pick Roller, PL10.1.43 • Tray 1 (MPT) Retard Roller, PL10.1.16 • Registration Clutch #1, PL8.1.85 • Tray 2 Registration Motor, PL4.2.36 • Tray 2 Feed Motor, PL4.2.35 • Front Sensor Board, PL4.2.97
Remedy:	1 Check the following for evidence of fault, dirt, debris, or damage: • Tray 1 (MPT) Feed Rollers • Registration Rollers • Sensor Actuator Is there any damage or debris? Clean or replace the appropriate parts. Go to Step 2. 2 Test the Registration #1 Sensor. Run the Service Diagnostics Registration Entrance Sensor test. Does the sensor operate correctly? Go to Step 3. Replace the actuator. If the error persists, replace the Front Sensor Board. 3 Test the Feed Motor, Registration Motor, and Registration Clutch #1. Do the components function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check the harness for each motor and clutch. Are the wiring harnesses properly connected and free from defects? Replace the Engine Control Board. Replace the wiring harness and/or the problem motor/ clutch.

Error code:	A2
Display:	DOCUMENT JAM
Description:	Jam at Door A
Causes:	• Duplex Unit, PL16.1.0
Remedy:	1 Check the following for evidence of fault, dirt, debris, or damage: • Door A • Door D • Duplex Unit Rollers • Duplex Unit connector • Duplex Sensors and Actuators Is there any damage or debris? Clean or replace the appropriate parts. Go to Step 2. 2 Test the Duplex Unit sensors. Run the Service Diagnostics for each of the four Duplex Unit sensors. Do the sensors and actuators function correctly Go to Step 3. Replace the damaged sensor. 3 Test the Duplex Unit motors. Run the Service Diagnostics Duplex Motor tests. Do the motors function correctly Go to Step 4. Replace the Duplex Unit 4 Inspect the wiring harness for the Duplex Unit. Is the wiring harness properly connected and free from defects? Replace the Duplex Unit. Replace the Engine Control Board.

Error code:	A3
Display:	DOCUMENT JAM
Description:	Jam at Door A Misfeed at Tray 1 (MPT) Media reached the Duplex Reverse Sensor, but a second sheet was detected entering the feed path from Tray 1 (MPT). This error represents a misfeed jam for media fed from Tray 1 (MPT).
Causes:	• Tray 1 (MPT) Feed Roller, PL10.1.53 • Tray 1 (MPT) Pick Roller, PL10.1.43 • Tray 2 Registration Motor, PL4.2.36 • Tray 2 Feed Motor, PL4.2.35 • Front Sensor Board, PL4.2.97
Remedy:	1 Check the following for evidence of fault, dirt, debris, or damage: • Tray 1 (MPT) Feed Rollers • Registration Rollers • Sensor Actuator Is there any damage or debris? Clean or replace the appropriate parts. Go to Step 2. 2 Test the Registration #1 Sensor. Run the Service Diagnostics Registration Entrance Sensor test. Does the sensor operate correctly? Go to Step 3. Replace the actuator. If the error persists, replace the Front Sensor Board. 3 Test the Feed Motor, Registration Motor, and Registration Clutch #1. Do the components function correctly? Replace the Engine Control Board. Go to Step 4. 4 Check each motor and clutch harness. Are the harnesses properly connected and free from defects? Replace the Engine Control Board. Replace the harness and/or problem motor/ clutch.

Error code:	A4
Display:	Cover is Open
Description:	Sorter problem
Causes:	• Defective engine gate array • Defective fuse cut circuit on the engine board
Remedy:	Correct catching of the ADF cover open sensor. Replace the ADF cover. Replace the ADF cover open sensor. Replace the ADF relay PCB ASSY. Replace the main PCB ASSY.

Error code:	B1 ... B6
Description:	Feed cassette bottom plate motor error The feed cassette bottom plate motor won’t revolve.
Causes:	• Excessive torque on the motor (activating the current protection circuit) • Stuck motor • Defective feed board PU (U1) • Defective motor driver circuit (transistors) or over-current detector circuit

Error code:	C1
Description:	PF jam cass. 1
Causes:	• If the actuator of the Separation base unit safety switch is not depressed.
Remedy:	This may happen in some cases of bad line condition. Ask the remote party to transmit again.

Error code:	C2
Description:	PF jam cass. 2
Causes:	• If the actuator of the Master making unit safety switch is not depressed.
Remedy:	This may happen in some cases of bad line condition. Ask the remote party to transmit again.

Error code:	C4
Display:	SVC C4 ERROR
Description:	Machine has reset
Causes:	• If the master disposal box set sensor does not detect.
Remedy:	This may happen in some cases of bad line condition. Ask the remote party to transmit again.

Error code:	C5
Display:	C5:ILLEGAL SIZE
Description:	Optics locked or not initialized. Could be scan or lens/mirror
Causes:	• If the Ink bottle set sensor does not detect the Ink bottle.
Remedy:	Set the Ink bottle in the Drum.

Error code:	C6
Description:	Scan problem
Causes:	• If the black tape attached at the end of the Master roll has been detected by the Master end sensor during master making or confidential operation.
Remedy:	Master making unit safety SW OFF & ON. • Replace the depleted Master roll with a new one.

Error code:	C8
Description:	Paper stays in tray or duplex or HCF
Causes:	• If the Ink sensor does not detect ink in the Squeegee unit within 20 seconds after the Inking motor was activated. • If the Ink sensor does not detect ink in the Squeegee unit within 40 seconds after the Inking motor was activated when the Ink bottle is installed just after replacing empty ink bottle.
Remedy:	Ink bottle set sensor OFF & 5 seconds later ON.

Error code:	C9
Description:	Bypass jam
Remedy:	Replace the main PCB ASSY.

Error code:	CA
Description:	Main board problem
Remedy:	Check the harness connection of the USB host relay PCB ASSY and reconnect it. Replace the USB host relay PCB ASSY. Replace the main PCB ASSY.

Error code:	CB
Description:	ADF drive problem
Remedy:	1 Harness connection failure of registration mark sensor holder ASSY Check the harness connection of the registration mark sensor holder ASSY and reconnect it. 2 Density sensor failure Replace the registration mark sensor holder ASSY. 3 Main PCB failure Replace the main PCB ASSY.

Error code:	CD
Description:	BC RAM hardware
Causes:	The CD error also suggests that the sorter ST-30 is defective.
Remedy:	Clean both electrodes. Replace the HVPS PCB unit. Replace the main PCB ASSY.

Error code:	CC
Description:	ADF drive problem
Causes:	When SIM1-2 is executed, the sensor’s light receiving level for each document size does not agree with the setting.
Remedy:	Clear the trouble by turning the power supply On/Off. Check document detection lighting section height.

Error code:	E2
Display:	SVC E2 ERROR
Description:	Reset signal happened. Might read E-2 something else.

Error code:	F0
Display:	SVC F0 ERROR
Description:	The communication ended because of a WDT due to an overrun of the software.
Causes:	Defective main controller PWB. Defective operator panel PWB. Defective mainengine controllers relay PWB. Defective engine controller PWB . Defective harness between engine controller PWB and operator panel PWB, or poor contact of the connector terminals.
Remedy:	Attempt the communication again. If the error occurs frequently, perform a memory clear (except user area.)

Error code:	F1
Display:	F1
Description:	Collator jam
Remedy:	Attempt the communication again. If the error occurs frequently, perform a memory clear (except user area.)

Error code:	E0
Display:	SVC E0 ERROR
Description:	Machine has reset
Causes:	• Error with CPU and gate arrays of either the engine or main controller • Connection error between the engine board and the main controller board • Program overrun in the engine or main controllere
Remedy:	Remove the cause of the printer error, then ask the remote party to transmit again.

Error code:	E1
Display:	SVC E1 ERROR
Description:	Jam at Door E Paper misfeed jam between the Fuser and the Top Output Tray. Media reached the Fuser Exit Sensor, but did not reach the Top Output Tray Stack Full Sensor on time. This error represents a misfeed jam inside the Exit Assembly.
Causes:	• Exit Assembly, PL11.1.0 • Fuser Motor, PL2.1.9 • Exit Gate Solenoid, PL11.1.17 • Full Stack Sensor, PL11.1.39
Remedy:	1 Check the following for evidence of fault or damage: • Door E • Fuser • Exit Rollers and drive gears • Stack Full Actuator • Exit Assembly Is there any damage or debris? Replace any damaged parts. Go to Step 2. 2 Test the Fuser Exit and Top Output Tray Stack Full Sensors. Do the sensors function correctly? Go to Step 4. Replace the sensor. If the error persists, go to Step 3. 3 Check all pins on the SNS Harness for continuity. Is the harness conductive? Go to Step 4. Replace the SNS Harness. 4 Test the Fuser Motor. Run the Service Diagnostics Fuser Motor test. Does the motor function correctly? Go to Step 6. Replace the motor. If the error persists, go to Step 5. 5 Check for +24 V to the Fuser Motor. Disconnect DCHEAT on the Motor Driver Board. Is there +24 V across DCHEAT-3 <=> ground? Go to Step 6. Replace the Motor Driver Board. If the error persists, go to Step 6. 6 Test the Exit Gate Solenoid. Run the Service Diagnostics Exit Gate Solenoid test. Does the solenoid function correctly. Go to Step 8. Replace the solenoid. If the error persists, go to Step 7. 7 Check for +24 V to the solenoid. 1. Actuate the interlock switches. 2. Disconnect SOLENOID from the Rear Sensor Board. Is there +24 V across SOLENOID-1 <=> ground? Go to Step 8. Replace the Rear Sensor Board. 8 Check the DRV0 and DRV1 ribbon cables that connect the Motor Driver Board to the Engine Control Board. Are these cables connected and undamaged? Replace the Engine Control Board. Replace the harnesses.

Error code:	E3
Display:	SVC E3 ERROR
Description:	Jam in transfer area
Causes:	• If the light path of the Clamp senors both C and L are not opened within 10 seconds after after the Clamp motor is activated. [During Master Release from the Clamp Plate] • If the light path of the Clamp sensor L is not blocked within 10 seconds after the Clamp motor is activated. • If the light path of the Clamp sensor C is not opened within 10 seconds after the Clamp motor is activated. [When the Clamp Plate opens during Master Clamping] • If the light path of the Clamp sensor L is not blocked within 10 seconds after the Clamp motor is activated. • If the light path of the Clamp sensor C is not opened within 10 seconds after the Clamp motor is activated. [When the Clamp Plate closes during Master Clamping] • If the light path of the Clamp sensor L is not opened within 10 seconds after the Clamp motor is activated.
Remedy:	Paper exit detector (POUT) signal recognition error 1) Paper exit detector (POUT) trouble 2) Paper exit detector (POUT) signal input circuit trouble REMEDY (Check) 1) Paper exit detector (POUT) 2) MCU PWB paper exit detector (POUT) signal input circuit (Remedy) 1) Paper exit detector (POUT) replacement 2) MCU PWB replacement (After work) 1) When the MCU PWB is replaced, perform simulations to input various set values and adjustment values.

Error code:	E4
Display:	E4-2:EXITJAM
Description:	Exit jam
Causes:	• If the Overflow sensor detects excessive ink in the Squeegee unit.
Remedy:	Remove excess ink from the Drum.

Error code:	E5
Display:	SVC E5 ERROR
Description:	Front door open
Causes:	• Connector error between CON1 board and the drum liaison board • Defective connector between the drum liaison board and the drum board • Defective transistors and logic gate ICs in the eraser controller circuit on the engine board • Connection error between drum unit board and eraser lamp • Broken eraser lamp

Error code:	E8
Display:	SVC E8 ERROR
Description:	Jam in ADD (duplex)
Causes:	• Defective gate array U6 • Defective fuse cut circuit on the engine board

Error code:	E9
Display:	E9-Top Cover A Open
Description:	The top cover (Cover A) is open. Close the cover so that printing can continue.
Causes:	• Overcurrent in the toner motor circuitry due to an excessive torque • Toner motor locked • Defective gate array U2 • Defective toner motor driver transistor or overcurrent detector.
Remedy:	1. Close the cover. 2. Inspect the switch and ensure the switch’s actuator is not broken. 3. Test the top cover open switch using the sensor test described in “Switch scan test”. Inspect the switch’s wiring harness. 5. Replace the engine controller board.

Kyocera FS-7000

Общие характеристики

Макс. формат

Технология печати

Цветность печати

Тип

Число страниц в месяц

Область применения

Сканер

Печать фотографий

Копир

Тип устройства

Принтер

Двусторонняя печать

Прямая печать

Макс, разрешение для ч/б печати

Расходные материалы

Ресурс ч/б картриджа/тонера

Печать на:

Языки управления

Лотки

Подача бумаги

Вывод бумаги

Интерфейсы

Инфракрасный порт

Ethernet (RJ-45)

LPT

USB

Память/Процессор

Объем памяти

Макс, объем памяти

Дополнительная информация

Поддержка ОС

Уровень шума

Габариты

Вес

Глубина

Высота

Ширина

Коды ошибок

Описание

Парткод

Название

Позвонить

Написать

Спасибо за ваше сообщение!

Оставить заявку