Kyocera ECOSYS P6030cdn
Рейтинг
Модули
PAPER FEED
DRIVE SECTION
Covers 2
DEVELOPING SECTION
ELECTRICAL COMPONENTS
Exit Section
FRAMES 1
FRAMES 2
Paper Conveying Section
Image Formation Section
(Узел переноса)
Paper Feed Section 1
Fuser Section
CASSETTE ASSEMBLY
PAPER FEED SECTION 2
(Узел термозакрепления)
PAPER CASSETTE
Covers 1
Детали CASSETTE ASSEMBLY
| Деталь: | Блок проявки |
| Парткод: | DV-560C |
| Цена: | 12 800 ₽ |
| Деталь: | Блок проявки |
| Парткод: | DV-560K |
| Цена: | 12 800 ₽ |
| Деталь: | Блок проявки |
| Парткод: | DV-560M |
| Цена: | 12 800 ₽ |
| Деталь: | Блок проявки |
| Парткод: | DV-560Y |
| Цена: | 12 800 ₽ |
| Деталь: | PLATE DRIVE |
| Парткод: | 302HN31070 |
| Деталь: | GEAR Z74R-Z35L |
| Парткод: | 302HN31080 |
| Деталь: | GEAR Z54R |
| Парткод: | 302HN31090 |
| Деталь: | GEAR Z33L |
| Парткод: | 302HN31100 |
| Деталь: | PARTS MOTOR BL W25 SP |
| Парткод: | 302KK94540 |
| Деталь: | BELT FEED HANDLE |
| Парткод: | 2FB17260 |
| Деталь: | HOLDER FEED DRIVE A |
| Парткод: | 302HN31111 |
| Деталь: | HOLDER FEED DRIVE B |
| Парткод: | 302HN31120 |
| Деталь: | GEAR Z77R-Z25R |
| Парткод: | 302HN31130 |
| Деталь: | GEAR Z39L |
| Парткод: | 302HN31141 |
| Деталь: | GEAR Z32R IDLE |
| Парткод: | 302HN31150 |
| Деталь: | GEAR Z30L |
| Парткод: | 302HN31160 |
| Деталь: | GEAR Z32L CL FEED |
| Парткод: | 302HN31170 |
| Деталь: | GEAR Z28R INPUT DU |
| Парткод: | 302HN31180 |
| Деталь: | GEAR Z31R-Z26R INPUT REGIST |
| Парткод: | 302HN31190 |
| Деталь: | GEAR Z35L |
| Парткод: | 302HN31200 |
| Деталь: | GEAR Z36R-Z22S |
| Парткод: | 302HN31210 |
| Деталь: | GEAR Z28S |
| Парткод: | 302HN31220 |
| Деталь: | GEAR Z36S MPF CAM |
| Парткод: | 302HN31240 |
| Деталь: | CAM MPF |
| Парткод: | 302HN31250 |
| Деталь: | GEAR Z62R-P32 |
| Парткод: | 302HN31260 |
| Деталь: | GEAR Z30L-P30 |
| Парткод: | 302HN31270 |
| Деталь: | GEAR Z32R CL DLP |
| Парткод: | 302HN31280 |
| Деталь: | GEAR Z33L INPUT DLP |
| Парткод: | 302HN31290 |
| Деталь: | GEAR Z81R-Z35L |
| Парткод: | 302HN31300 |
| Деталь: | GEAR Z70R |
| Парткод: | 302HN31311 |
| Деталь: | GEAR Z70L |
| Парткод: | 302HN31320 |
| Деталь: | GEAR Z38L |
| Парткод: | 302HN31330 |
| Деталь: | GEAR Z38R INPUT MT |
| Парткод: | 302HN31340 |
| Деталь: | GEAR Z72L-Z26S |
| Парткод: | 302HN31350 |
| Деталь: | GEAR Z40S INPUT FUSER |
| Парткод: | 302HN31360 |
| Деталь: | SHAFT CLUTCH FEED |
| Парткод: | 302HN31370 |
| Деталь: | PIN DRIVE DLP |
| Парткод: | 302HN31390 |
| Деталь: | SPRING FEED |
| Парткод: | 302HN31410 |
| Деталь: | SPRING MID TRANSFER |
| Парткод: | 302HN31430 |
| Деталь: | PLATE MOTOR FUSER |
| Парткод: | 302HN31560 |
| Деталь: | BUSH DRIVE |
| Парткод: | 302HN31590 |
| Деталь: | GEAR Z36S INPUT MPF A |
| Парткод: | 302HN31620 |
| Деталь: | GEAR Z36S INPUT MPF B |
| Парткод: | 302HN31630 |
| Деталь: | PIN DRIVE MT |
| Парткод: | 302HN31640 |
| Деталь: | SPRING INPUT MPF |
| Парткод: | 302HN31650 |
| Цена: | 150 ₽ |
| Деталь: | JOINT SHAFT CASSETTE |
| Парткод: | 302HN31660 |
| Деталь: | PIN DRIVE A |
| Парткод: | 302HN31670 |
| Деталь: | PIN DRIVE B |
| Парткод: | 302HN31680 |
| Деталь: | MOTOR FUSER |
| Парткод: | 302HN44090 |
| Деталь: | SOLENOID MPF |
| Парткод: | 302HN44160 |
| Деталь: | CLUTCH FEED L |
| Парткод: | 302HN44200 |
| Деталь: | CONNECTOR 292254-2 |
| Парткод: | 7YCC02B1003+H01 |
| Деталь: | MOTOR DRUM |
| Парткод: | 302HN44050 |
| Деталь: | FOOT |
| Парткод: | 302HN02611 |
| Деталь: | BRACKET DRIVE LIFT |
| Парткод: | 302HN31010 |
| Деталь: | COVER GEAR LIFT |
| Парткод: | 302HN31020 |
| Деталь: | GEAR Z36L-Z20S |
| Парткод: | 302HN31030 |
| Деталь: | GEAR Z46S-Z13S |
| Парткод: | 302HN31040 |
| Деталь: | GEAR Z13S |
| Парткод: | 302HN31050 |
| Деталь: | GEAR Z35S-Z13S |
| Парткод: | 302HN31060 |
| Деталь: | GEAR Z34S |
| Парткод: | 302HN31540 |
| Деталь: | SPRING DRIVE LIFT |
| Парткод: | 302HN31550 |
| Деталь: | DC MOTOR ASSY LIFT SP |
| Парткод: | 302HN94261 |
| Деталь: | DR-580B |
| Парткод: | 302K893080 |
| Деталь: | DR-580A |
| Парткод: | 302K893070 |
| Деталь: | DRIVE LIFT ASSY SP |
| Парткод: | 302HN94182 |
| Деталь: | SPRING LOCK MPF |
| Парткод: | 302F908300 |
| Деталь: | GEAR MANUAL |
| Парткод: | 302B700780 |
| Деталь: | FERRITE CORE |
| Парткод: | 7YBFG0509001H01 |
| Деталь: | GUIDE FRONT COVER RELEASE LEFT |
| Парткод: | 302HN04151 |
| Деталь: | SHAFT FRONT COVER RELEASE |
| Парткод: | 302HN04160 |
| Деталь: | STOPPER FRONT COVER RIGHT |
| Парткод: | 302HN04170 |
| Деталь: | STOPPER FRONT COVER LEFT |
| Парткод: | 302HN04181 |
| Деталь: | GUIDE FRONT COVER RELEASE RIGHT |
| Парткод: | 302HN04221 |
| Деталь: | SPRING FRONT COVER |
| Парткод: | 302HN04270 |
| Деталь: | CONN.CORD ASSY S03285 |
| Парткод: | 302HN46320 |
| Деталь: | CONN.CORD ASSY S03386 |
| Парткод: | 302HN46480 |
| Деталь: | BASE MPF |
| Парткод: | 302HN08010 |
| Деталь: | COVER MPF |
| Парткод: | 302HN08020 |
| Деталь: | TRAY MPF TOP |
| Парткод: | 302HN08030 |
| Деталь: | GUIDE MPF L |
| Парткод: | 302HN08050 |
| Деталь: | GUIDE MPF R |
| Парткод: | 302HN08060 |
| Деталь: | LUTCH |
| Парткод: | 302HN08140 |
| Деталь: | LINK LEVER MPF L |
| Парткод: | 302HN08150 |
| Деталь: | LINK LEVER MPF R |
| Парткод: | 302HN08160 |
| Деталь: | ROLLER DU |
| Парткод: | 302HN29010 |
| Деталь: | ROLLER DU FEED |
| Парткод: | 302HN29020 |
| Деталь: | BASE DU |
| Парткод: | 302HN29031 |
| Деталь: | PULLEY P24 S2M DU |
| Парткод: | 302HN29040 |
| Деталь: | BUSH DU |
| Парткод: | 302HN29050 |
| Деталь: | GEAR Z23L DU FEED |
| Парткод: | 302HN29060 |
| Деталь: | HOOK DU RELEASE LEFT |
| Парткод: | 302HN29070 |
| Деталь: | HOOK DU RELEASE RIGHT |
| Парткод: | 302HN29080 |
| Деталь: | COVER INNER DU |
| Парткод: | 302HN29101 |
| Деталь: | SPRING DU EARTH A |
| Парткод: | 302HN29130 |
| Деталь: | SPRING DU EARTH B |
| Парткод: | 302HN29140 |
| Деталь: | BELT DU |
| Парткод: | 302HN29150 |
| Деталь: | HOOK CONVEYING |
| Парткод: | 302HN29160 |
| Деталь: | SPRING DU EARTH C |
| Парткод: | 302HN29170 |
| Деталь: | SHEET BASE DU |
| Парткод: | 302HN29190 |
| Деталь: | COVER LOWER LEFT |
| Парткод: | 302HN04111 |
| Деталь: | COVER LOWER RIGHT |
| Парткод: | 302HN04120 |
| Деталь: | P.W.BOARD ASSY LCD CONT |
| Парткод: | 302HN01030 |
| Деталь: | PARTS PWB ASSY LCDCONT SP |
| Парткод: | 302PP94100 |
| Деталь: | MOUNT LCD UPPER |
| Парткод: | 302HN05022 |
| Деталь: | MOUNT LCD LOWER |
| Парткод: | 302HN05030 |
| Деталь: | BUTTON A |
| Парткод: | 302HN05041 |
| Деталь: | BUTTON B |
| Парткод: | 302HN05050 |
| Деталь: | BUTTON C |
| Парткод: | 302HN05060 |
| Деталь: | BUTTON C |
| Парткод: | 302PP05020 |
| Деталь: | LABEL 6 NATIONS |
| Парткод: | 302HN05180 |
| Деталь: | COVER FRONT SUB ASSY |
| Парткод: | 302K894010 |
| Деталь: | PARTS COVER FRONT SUB ASSY SP |
| Парткод: | 302PP94030 |
| Деталь: | KEY BORAD ASSY SP |
| Парткод: | 302HN94241 |
| Деталь: | PARTS KEY BOARD ASSY SP |
| Парткод: | 302PP94050 |
| Деталь: | DV-560(K) |
| Парткод: | 302HN93013 |
| Деталь: | DV-560 US (K) |
| Парткод: | 302HN93253 |
| Деталь: | DV-560(Y) |
| Парткод: | 302HN93023 |
| Деталь: | DV-560 US (Y) |
| Парткод: | 302HN93263 |
| Деталь: | DV-560(C) |
| Парткод: | 302HN93033 |
| Деталь: | DV-560 US (C) |
| Парткод: | 302HN93273 |
| Деталь: | DV-560(M) |
| Парткод: | 302HN93043 |
| Деталь: | DV-560 US (M) |
| Парткод: | 302HN93283 |
| Деталь: | CONN.CORD ASSY S03284 |
| Парткод: | 302HN46310 |
| Деталь: | P.W.BOARD ASSY RFID WITH SOFTWARE |
| Парткод: | 302HG01240 |
| Деталь: | CONN.CORD ASSY S03300 |
| Парткод: | 302HN46440 |
| Деталь: | CONN.CORD ASSY S03287 |
| Парткод: | 302HN46340 |
| Деталь: | CONN.CORD ASSY S03274 |
| Парткод: | 302HN46210 |
| Деталь: | CONN.CORD ASSY S03436 |
| Парткод: | 302HN46580 |
| Деталь: | SW.MICRO |
| Парткод: | 7SM010104+++H01 |
| Деталь: | CONN.CORD ASSY S03268 |
| Парткод: | 302HN46150 |
| Деталь: | ID SENSOR ASSY SP |
| Парткод: | 302HN94320 |
| Деталь: | SHIELD HV |
| Парткод: | 302HN39042 |
| Деталь: | DUCT CONTROLLER |
| Парткод: | 302HN39050 |
| Деталь: | BRACKET HV PWB |
| Парткод: | 302HN39082 |
| Деталь: | FAN PS ASSY SP |
| Парткод: | 302HN94230 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZGSTG15C050H01 |
| Деталь: | HIGH VOLTAGE UNIT SP |
| Парткод: | 302K894030 |
| Деталь: | CONN.CORD ASSY S03301 |
| Парткод: | 302HN46450 |
| Деталь: | PLATE ENGINE |
| Парткод: | 302HN39011 |
| Деталь: | SOLENOID FD ASSY CLN SP |
| Парткод: | 302HN94220 |
| Деталь: | PARTS PWB ENGINE SP |
| Парткод: | 302K894050 |
| Деталь: | PARTS PWB ASSY ENGINE SP |
| Парткод: | 302PP94090 |
| Деталь: | ACTUATOR CASSETTE |
| Парткод: | 302HN39070 |
| Деталь: | ACTUATOR PICKUP |
| Парткод: | 302HN06050 |
| Деталь: | SPRING PICK ACT |
| Парткод: | 302HN06060 |
| Деталь: | CONN.CORD ASSY S03282 |
| Парткод: | 302HN46290 |
| Деталь: | CONN.CORD ASSY S03283 |
| Парткод: | 302HN46300 |
| Деталь: | LINK LEVER |
| Парткод: | 302HN02660 |
| Деталь: | LK-580 A |
| Парткод: | 302K893040 |
| Деталь: | LK-580 B |
| Парткод: | 302K893050 |
| Деталь: | PLATE CONTROLLER |
| Парткод: | 302HN39021 |
| Деталь: | PLATE CONTROLLER |
| Парткод: | 302PP39010 |
| Деталь: | PLATE,OPTION |
| Парткод: | 303BH26021 |
| Деталь: | PLATE OPTION |
| Парткод: | 302K339050 |
| Деталь: | SCREW OP / M3 X 8 CRFREE A4 |
| Парткод: | 5MMT263SN012++R |
| Деталь: | PARTS PWB MAIN SP |
| Парткод: | 302K894040 |
| Деталь: | PARTS PWB ASSY MAIN SP |
| Парткод: | 302PP94070 |
| Деталь: | PARTS PWB ASSY MAIN EU SP |
| Парткод: | 302PP94080 |
| Деталь: | RAIL OPTION |
| Парткод: | 302HN39060 |
| Деталь: | RAIL OPTION |
| Парткод: | 302PP39020 |
| Деталь: | CONN.CORD ASSY S03296 |
| Парткод: | 302HN46400 |
| Деталь: | CONN.CORD ASSY S03297 |
| Парткод: | 302HN46410 |
| Деталь: | CONN.CORD ASSY S03298 |
| Парткод: | 302HN46420 |
| Деталь: | CONN.CORD ASSY S03299 |
| Парткод: | 302HN46430 |
| Деталь: | CONN.CORD ASSY S03254 |
| Парткод: | 302HN46020 |
| Деталь: | CONN.CORD ASSY S03293 |
| Парткод: | 302HN46380 |
| Деталь: | CONN.CORD ASSY S03388 |
| Парткод: | 302HN46500 |
| Деталь: | CONN.CORD ASSY S03261 |
| Парткод: | 302HN46090 |
| Деталь: | CONN.CORD ASSY S03253 |
| Парткод: | 302HN46010 |
| Деталь: | CONN.CORD ASSY S03431 |
| Парткод: | 302HN46560 |
| Деталь: | CONN.CORD ASSY S03387 |
| Парткод: | 302HN46490 |
| Деталь: | PARTS SWITCHING REGULATOR 120V SP |
| Парткод: | 302K894060 |
| Деталь: | SWITCHING REGULATOR 230V |
| Парткод: | 302HN45031 |
| Деталь: | PARTS SWITCHING REGULATOR 230V SP |
| Парткод: | 302PP94060 |
| Деталь: | SHIELD POWER |
| Парткод: | 302HN39030 |
| Деталь: | CAP NETWORK |
| Парткод: | 302F939090 |
| Деталь: | SPRING HV PT |
| Парткод: | 302HN39090 |
| Деталь: | SPRING ACTUATOR |
| Парткод: | 302HN39110 |
| Деталь: | SEAL LEFT WASTE A |
| Парткод: | 302HN02890 |
| Деталь: | SHEET HOUSING LEFT |
| Парткод: | 302HN02930 |
| Деталь: | SEAL DUCT TOP |
| Парткод: | 302HN02940 |
| Деталь: | SEAL DUCT HALF |
| Парткод: | 302HN02950 |
| Деталь: | SHEET FRONT |
| Парткод: | 302HN02980 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZGSTG110075H01 |
| Деталь: | SHIELD GASKET |
| Парткод: | 7ZGSTG110155H01 |
| Деталь: | POWER CORD(120) |
| Парткод: | 3019527401 |
| Деталь: | AC CORD ASSY |
| Парткод: | 302FV45020 |
| Деталь: | AC CORD ASSY |
| Парткод: | 302FV45040 |
| Деталь: | PULLEY MID /B-11 FRAME A4 |
| Парткод: | 2FM02210 |
| Деталь: | STUD SCREW M3 |
| Парткод: | 302F325010 |
| Деталь: | ACTUATOR SOL |
| Парткод: | 302F925060 |
| Деталь: | HOUSING EXIT |
| Парткод: | 302HN28010 |
| Деталь: | ROLLER FD |
| Парткод: | 302HN28021 |
| Деталь: | ROLLER REVERSE |
| Парткод: | 302HN28030 |
| Деталь: | GEAR Z55R-Z17R |
| Парткод: | 302HN28050 |
| Деталь: | GEAR Z23S FD |
| Парткод: | 302HN28060 |
| Деталь: | GEAR Z20L REVERSE |
| Парткод: | 302HN28071 |
| Деталь: | ACTUATOR FULL |
| Парткод: | 302HN28080 |
| Деталь: | GUIDE EXIT UP |
| Парткод: | 302HN28090 |
| Деталь: | GUIDE CHANGE |
| Парткод: | 302HN28100 |
| Деталь: | SPRING SOLENOID |
| Парткод: | 302HN28110 |
| Деталь: | SPRING PULLEY A |
| Парткод: | 302HN28120 |
| Деталь: | PLATE MOTOR A |
| Парткод: | 302HN28130 |
| Деталь: | GUIDE CORRUGATION |
| Парткод: | 302HN28140 |
| Деталь: | SPRING EARTH EXIT A |
| Парткод: | 302HN28150 |
| Деталь: | SPRING EARTH EXIT B |
| Парткод: | 302HN28160 |
| Деталь: | SPRING EARTH EXIT C |
| Парткод: | 302HN28170 |
| Деталь: | STAY FRONT |
| Парткод: | 302HN28180 |
| Деталь: | SPRING EARTH EXIT D |
| Парткод: | 302HN28190 |
| Деталь: | GEAR Z28S IDLE |
| Парткод: | 302HN28200 |
| Деталь: | DISCHARGER FD |
| Парткод: | 302HN28210 |
| Деталь: | SEAL ACTUATOR |
| Парткод: | 302HN28220 |
| Деталь: | SHEET PULLEY |
| Парткод: | 302HN28230 |
| Деталь: | SHEET CHANGE |
| Парткод: | 302HN28240 |
| Деталь: | SPRING GEAR |
| Парткод: | 302HN28250 |
| Деталь: | BUSH DU |
| Парткод: | 302HN29050 |
| Деталь: | MOTOR REVERSE |
| Парткод: | 302HN44100 |
| Деталь: | SOLENOID FD ASSY SP |
| Парткод: | 302HN94140 |
| Цена: | 5 200 ₽ |
| Деталь: | LABEL FUSER CAUTION |
| Парткод: | 5MVVL611WN06 |
| Деталь: | P.W.BOARD ASSY EXIT |
| Парткод: | 302HN01150 |
| Деталь: | CONN.CORD ASSY S03400 |
| Парткод: | 302HN46570 |
| Деталь: | CONN.CORD ASSY S03271 |
| Парткод: | 302HN46180 |
| Деталь: | FAN MOTOR |
| Парткод: | 302HN44210 |
| Деталь: | FAN MOTOR 50 |
| Парткод: | 302HG44110 |
| Деталь: | PARTS EXIT ASSY(25) |
| Парткод: | 302HN93141 |
| Деталь: | HOLDER RFID |
| Парткод: | 302HN02210 |
| Деталь: | DC MOTOR ASSY LSU SP |
| Парткод: | 302HN94110 |
| Деталь: | GEAR Z63R-Z25R |
| Парткод: | 302HN03430 |
| Деталь: | GEAR Z54S |
| Парткод: | 302HN03450 |
| Деталь: | GEAR Z70L-Z17S |
| Парткод: | 302HN03440 |
| Деталь: | MOUNT GLASS CLN DRIVE |
| Парткод: | 302HN03410 |
| Деталь: | DC MOTOR ASSY K SP |
| Парткод: | 302HN94060 |
| Деталь: | DC MOTOR ASSY Y SP |
| Парткод: | 302HN94070 |
| Деталь: | DC MOTOR ASSY C SP |
| Парткод: | 302HN94080 |
| Деталь: | DC MOTOR ASSY M SP |
| Парткод: | 302HN94090 |
| Деталь: | FRAME REAR |
| Парткод: | 302HN02050 |
| Деталь: | RACK TONER SUPPLY R |
| Парткод: | 302HN02170 |
| Деталь: | ACTUATOR CONTAINER |
| Парткод: | 302HN02701 |
| Деталь: | SPRING ACT CONT |
| Парткод: | 302HN02710 |
| Деталь: | GEAR Z16S HINGE |
| Парткод: | 302HN02150 |
| Деталь: | CAM TONER SUPPLY |
| Парткод: | 302HN02190 |
| Деталь: | GEAR Z20S-Z26L |
| Парткод: | 302HN15030 |
| Деталь: | GEAR Z50S |
| Парткод: | 302HN15020 |
| Деталь: | SPRING JOINT |
| Парткод: | 302HN15040 |
| Деталь: | HOLDER HARNESS |
| Парткод: | 302HN02200 |
| Деталь: | DUCT RIGHT |
| Парткод: | 302HN02230 |
| Деталь: | FAN MOTOR |
| Парткод: | 302HN44020 |
| Деталь: | HOLDER MCH CLN MOTOR |
| Парткод: | 302HN03340 |
| Деталь: | DC MOTOR ASSY MCH SP |
| Парткод: | 302HN94100 |
| Деталь: | GEAR Z16L |
| Парткод: | 302HN03310 |
| Деталь: | GEAR Z14R |
| Парткод: | 302HN03320 |
| Деталь: | SHAFT MCH CLN |
| Парткод: | 302HN03360 |
| Деталь: | GEAR Z16S-Z14R |
| Парткод: | 302HN03330 |
| Деталь: | OZONE FILTER VOC700 |
| Парткод: | 302HN02990 |
| Деталь: | HOLDER MCH CLN DRIVE GEAR |
| Парткод: | 302HN03350 |
| Деталь: | PLATE CONTAINER C |
| Парткод: | 302HN02680 |
| Деталь: | PLATE CONTAINER K |
| Парткод: | 302HN02670 |
| Деталь: | ROD INTERLOCK |
| Парткод: | 302HN02300 |
| Деталь: | RACK TONER SUPPLY L |
| Парткод: | 302HN02160 |
| Деталь: | RATCHET CONTAINER |
| Парткод: | 302HN02180 |
| Деталь: | SEAL SQUARE 25-20 |
| Парткод: | 302HN02720 |
| Деталь: | Hinge Left |
| Парткод: | 302HN02130 |
| Деталь: | Hinge Right |
| Парткод: | 302HN02140 |
| Деталь: | GUIDE CONTAINER K |
| Парткод: | 302HN15070 |
| Деталь: | GUIDE CONTAINER Y |
| Парткод: | 302HN15080 |
| Деталь: | GUIDE CONTAINER C |
| Парткод: | 302HN15090 |
| Деталь: | GUIDE CONTAINER M |
| Парткод: | 302HN15110 |
| Деталь: | SEAL CIRCLE 12 |
| Парткод: | 302HN02730 |
| Деталь: | SHEET FRAME REAR |
| Парткод: | 302HN02850 |
| Деталь: | SHEET SARCON |
| Парткод: | 302HN02870 |
| Деталь: | BLOCK HEAT CONDUCT |
| Парткод: | 302HN02860 |
| Деталь: | SPRING P CONT C |
| Парткод: | 302HN15160 |
| Деталь: | SPRING P CONT K |
| Парткод: | 302HN15170 |
| Деталь: | SEAL TN WASTE |
| Парткод: | 302HN02880 |
| Деталь: | RAIL CASSETTE |
| Парткод: | 302HN02740 |
| Деталь: | HINGE FEED LEFT |
| Парткод: | 302HN02080 |
| Деталь: | FOOT |
| Парткод: | 302HN02611 |
| Деталь: | BRACKET SWITCH |
| Парткод: | 302HN02541 |
| Деталь: | CONN.CORD ASSY S03290 |
| Парткод: | 302HN46350 |
| Деталь: | INLET ASSY |
| Парткод: | 302HN00050 |
| Деталь: | BRACKET BASE |
| Парткод: | 302HN02550 |
| Деталь: | BRACKET HARNESS |
| Парткод: | 302HN02620 |
| Деталь: | BRACKET HARNESS L |
| Парткод: | 302HN02630 |
| Деталь: | LOCK CASSETTE |
| Парткод: | 302HN02780 |
| Деталь: | COVER REAR |
| Парткод: | 302HN02070 |
| Деталь: | BRACKET HV K ASSY |
| Парткод: | 302HN94030 |
| Деталь: | CASE CONTACT HV K ASSY SP |
| Парткод: | 302HN94040 |
| Деталь: | SIDE SW ASSY |
| Парткод: | 302HN00060 |
| Деталь: | BRACKT HV C ASSY SP |
| Парткод: | 302HN94020 |
| Деталь: | BRACKET GEAR |
| Парткод: | 302HN02590 |
| Деталь: | GEAR Z25S WASTE |
| Парткод: | 302HN02320 |
| Деталь: | GEAR Z17S WASTE |
| Парткод: | 302HN02330 |
| Деталь: | GEAR Z20S WASTE |
| Парткод: | 302HN02340 |
| Деталь: | GEAR Z14L-Z17S WASTE |
| Парткод: | 302HN02350 |
| Деталь: | BRACKET FRONT |
| Парткод: | 302HN02250 |
| Деталь: | BRACKET HV TC ASSY SP |
| Парткод: | 302HN94010 |
| Деталь: | TONER FULL DETECT ASSY |
| Парткод: | 302HN00130 |
| Деталь: | SPRING LOCK DRUM |
| Парткод: | 302HN02500 |
| Деталь: | Inner cover |
| Парткод: | 302HN02580 |
| Деталь: | SEAL DUCT A |
| Парткод: | 302HN02810 |
| Деталь: | DUCT LEFT |
| Парткод: | 302HN02220 |
| Деталь: | SEAL DUCT D |
| Парткод: | 302HN02840 |
| Деталь: | BAR CLEANERED ID ASSY SP |
| Парткод: | 302HN94051 |
| Деталь: | SPRING CLEANER ID |
| Парткод: | 302HN02490 |
| Деталь: | FAN MOTOR |
| Парткод: | 302HN44010 |
| Деталь: | SPRING LOCK CASSETTE |
| Парткод: | 302HN02770 |
| Деталь: | WT-560 |
| Парткод: | 302HN93180 |
| Деталь: | ACCESS.SADDLE |
| Парткод: | 7YZM610007++H01 |
| Деталь: | PARTS WASTE TONER |
| Парткод: | 302HN93171 |
| Деталь: | BUSH REG R |
| Парткод: | 302HN24110 |
| Деталь: | SPRING REG R |
| Парткод: | 302HN24190 |
| Деталь: | STOPPER BUSH REG |
| Парткод: | 302HN24150 |
| Деталь: | SPRING REG L |
| Парткод: | 302HN24180 |
| Деталь: | SHEET REGIST FRONT |
| Парткод: | 302HN24160 |
| Деталь: | GEAR Z30S MPF |
| Парткод: | 302HN06150 |
| Деталь: | GEAR Z31R REG FRONT |
| Парткод: | 302HN24070 |
| Деталь: | FRAME CONVEYING |
| Парткод: | 302HN24042 |
| Деталь: | LABEL EXIT B |
| Парткод: | 302HG24180 |
| Деталь: | PLATE EARTH GUIDE |
| Парткод: | 302HN24090 |
| Деталь: | STOPPER TC SPRING |
| Парткод: | 302HN24370 |
| Деталь: | SPRING TC L |
| Парткод: | 302HG24150 |
| Деталь: | SPRING MPF B |
| Парткод: | 302HN06170 |
| Деталь: | SPRING EARTH FEED |
| Парткод: | 302HN24250 |
| Деталь: | HIGH MEG R ASSY |
| Парткод: | 302HN24430 |
| Деталь: | SPRING GUIDE EARTH |
| Парткод: | 302HN24280 |
| Деталь: | SPRING GUIDE EARTH B |
| Парткод: | 302HN24380 |
| Деталь: | SPRING SEP EARTH A |
| Парткод: | 302HN24270 |
| Деталь: | CONN.CORD ASSY S03264 |
| Парткод: | 302HN46110 |
| Деталь: | SENSOR OPT. |
| Парткод: | 7NXSG2481+++H01 |
| Деталь: | GUIDE FEED DU |
| Парткод: | 302HN24050 |
| Деталь: | PULLEY PA |
| Парткод: | 302HN24400 |
| Деталь: | SPRING DU |
| Парткод: | 302HN24290 |
| Деталь: | SPONGE A |
| Парткод: | 302HN24360 |
| Деталь: | ACTUATOR DU |
| Парткод: | 302HN24140 |
| Деталь: | SPRING ACT DU |
| Парткод: | 302HN24300 |
| Деталь: | FRAME MPF UP |
| Парткод: | 302HN06100 |
| Деталь: | ACTUATOR MPF |
| Парткод: | 302HN06121 |
| Деталь: | ACTUATOR MPF B |
| Парткод: | 302HN06131 |
| Деталь: | ROLLER M/P ASSY /43487B0027 A4 |
| Парткод: | 5AAVR0LL+051 |
| Цена: | 800 ₽ |
| Деталь: | SHAFT FEED MPF |
| Парткод: | 302HN06110 |
| Деталь: | ROLLER TRANSFER |
| Парткод: | 302HN22010 |
| Деталь: | PAPER CHUTE |
| Парткод: | 302HN22020 |
| Деталь: | HOLDER BRUSH |
| Парткод: | 302HN22030 |
| Деталь: | BUSH TRANS L |
| Парткод: | 302HN22050 |
| Деталь: | BUSH TRANS R |
| Парткод: | 302HN22060 |
| Деталь: | GEAR Z22L TC ROLL |
| Парткод: | 302HN22070 |
| Деталь: | SPRING SEP EARTH B |
| Парткод: | 302HN22080 |
| Деталь: | SHEET PAPER CHUTE |
| Парткод: | 302HN22110 |
| Деталь: | DISCHARGER TRANS |
| Парткод: | 302HN24460 |
| Деталь: | SPRING EARTH B |
| Парткод: | 302HN24390 |
| Деталь: | PLATE DISCHARGER |
| Парткод: | 302HN24471 |
| Деталь: | SHEET SEP PLATE |
| Парткод: | 302HN24481 |
| Деталь: | ROLLER REG FRONT SP |
| Парткод: | 302HN94170 |
| Деталь: | PARTS TRANSFER ASSY |
| Парткод: | 302HN93240 |
| Деталь: | MC-560 |
| Парткод: | 302HL93200 |
| Деталь: | DK-580 |
| Парткод: | 302K893010 |
| Деталь: | Intermediate transfer belt (ITB) |
| Парткод: | TR-580 |
| Цена: | 19 300 ₽ |
| Деталь: | Печь, в сборе (220В) |
| Парткод: | FK-580 |
| Цена: | 13 400 ₽ |
| Деталь: | SWITCH SIZE |
| Парткод: | 302HN44180 |
| Деталь: | PLATE EARTH SIZE |
| Парткод: | 302HN02470 |
| Деталь: | CONN.CORD ASSY S03266 |
| Парткод: | 302HN46130 |
| Деталь: | GUIDE HOUSING |
| Парткод: | 302HN06160 |
| Деталь: | PULLEY FEED SHIFT |
| Парткод: | 302C921041 |
| Деталь: | SPRING MIDDLE |
| Парткод: | 302HN24230 |
| Деталь: | ROLLER MIDDLE |
| Парткод: | 302HN24030 |
| Деталь: | GEAR Z27R MIDDLE |
| Парткод: | 302HN24080 |
| Деталь: | BUSH 6 EW |
| Парткод: | 302H024370 |
| Цена: | 190 ₽ |
| Деталь: | BUSH SCREW |
| Парткод: | 302H702590 |
| Деталь: | RING STOPPER /A-49 FEED A4 |
| Парткод: | 5MVX111DN003 |
| Деталь: | HOLDER SENSOR |
| Парткод: | 302HG02310 |
| Деталь: | GEAR Z19L REG REAR |
| Парткод: | 302HN24060 |
| Деталь: | BUSH REGIST CL |
| Парткод: | 302HN24350 |
| Деталь: | BUSH REGIST EW |
| Парткод: | 302HN24410 |
| Деталь: | SHEET REGIST FRONT |
| Парткод: | 302HN24160 |
| Деталь: | SPRING PICKUP |
| Парткод: | 302HG06010 |
| Деталь: | PIN FEED ROLL |
| Парткод: | 302F906110 |
| Деталь: | SW. PUSH |
| Парткод: | 7SP01000001+H01 |
| Деталь: | SHEET HOUSING |
| Парткод: | 302HN06180 |
| Деталь: | SEAL ACTUATOR |
| Парткод: | 302HN28220 |
| Деталь: | FAN MOTOR |
| Парткод: | 302HN44020 |
| Деталь: | HIGH MEG R ASSY |
| Парткод: | 302HN24430 |
| Деталь: | SPRING REG EARTH A |
| Парткод: | 302HN24260 |
| Деталь: | SPRING REG EARTH B |
| Парткод: | 302HN24420 |
| Деталь: | SPRING MID EARTH |
| Парткод: | 302HN24320 |
| Деталь: | SPRING CONTACT HV TC |
| Парткод: | 302HN02450 |
| Деталь: | SHAFT FEED R |
| Парткод: | 302HN06030 |
| Деталь: | BUSH DRIVE |
| Парткод: | 302HN31590 |
| Деталь: | GEAR FEED Z26H |
| Парткод: | 302F906030 |
| Деталь: | PULLEY FEED ASSY |
| Парткод: | 302F906230 |
| Цена: | 750 ₽ |
| Деталь: | SHAFT FEED L |
| Парткод: | 302F906272 |
| Деталь: | GEAR FEED Z30H |
| Парткод: | 302F906280 |
| Деталь: | HOLDER FEED |
| Парткод: | 302HN06010 |
| Деталь: | PULLEY PICKUP ASSY |
| Парткод: | 302HN06080 |
| Цена: | 480 ₽ |
| Деталь: | SENSOR,CONVEYING |
| Парткод: | 3H327410 |
| Деталь: | CONN.CORD ASSY S03326 |
| Парткод: | 302HG46090 |
| Деталь: | ROLLER REG REAR SP |
| Парткод: | 302HN94130 |
| Деталь: | HOLDER FEED ASSY SP |
| Парткод: | 302HN94201 |
| Цена: | 2 700 ₽ |
| Деталь: | FK-580(U) |
| Парткод: | 302K893031 |
| Деталь: | FK-580(E) |
| Парткод: | 302K893021 |
| Деталь: | Ролик отделения бумаги в держателе, в сборе |
| Парткод: | CET4322 |
| Цена: | 450 ₽ |
| Деталь: | Резина ролика отделения бумаги |
| Парткод: | CET4322PT |
| Цена: | 110 ₽ |
| Деталь: | Резина ролика захвата бумаги |
| Парткод: | CET7806BPT |
| Цена: | 110 ₽ |
| Деталь: | Резина ролика подачи бумаги |
| Парткод: | CET7829 |
| Цена: | 150 ₽ |
| Деталь: | PLATE BOTTOM MPF ASSY SP |
| Парткод: | 302HN94150 |
| Деталь: | SEPARATOR MPF ASSY SP |
| Парткод: | 302HN94160 |
| Цена: | 3 000 ₽ |
| Деталь: | SP BOTTOM MPF L |
| Парткод: | 302HN08080 |
| Деталь: | SP BOTTOM MPF R |
| Парткод: | 302HN08090 |
| Деталь: | SPRING SEPARATOR |
| Парткод: | 302HN08100 |
| Деталь: | FRAME MPF LOW |
| Парткод: | 302HN08111 |
| Деталь: | LEVER CAM MPF |
| Парткод: | 302HN08181 |
| Деталь: | HOLDER SEPARATOR MPF |
| Парткод: | 302HN08210 |
| Деталь: | TR-580 |
| Парткод: | 302K893101 |
| Деталь: | SEAL IMAGE REAR |
| Парткод: | 302HN02900 |
| Деталь: | Intermediate transfer belt (ITB) |
| Парткод: | TR-580 |
| Цена: | 19 300 ₽ |
| Деталь: | Печь, в сборе (220В) |
| Парткод: | FK-580 |
| Цена: | 13 400 ₽ |
| Деталь: | GEAR CASSETTE |
| Парткод: | 302B700770 |
| Деталь: | BUSH LIFT 6 |
| Парткод: | 302F909160 |
| Деталь: | RETARD ROLLER ASSY |
| Парткод: | 302F909171 |
| Цена: | 900 ₽ |
| Деталь: | HOLDER RETARD |
| Парткод: | 302F909180 |
| Деталь: | BASE CASSETTE |
| Парткод: | 302HN09012 |
| Деталь: | COVER CASSETTE TOP |
| Парткод: | 302HN09020 |
| Деталь: | GEAR Z20S-Z17S INDICATOR |
| Парткод: | 302HN09030 |
| Деталь: | MARKER INDICATOR |
| Парткод: | 302HN09041 |
| Деталь: | DIAL CASSETTE |
| Парткод: | 302HN09050 |
| Деталь: | CURSOR LEFT |
| Парткод: | 302HN09070 |
| Деталь: | LEVER GUIDE SIDE |
| Парткод: | 302HN09090 |
| Деталь: | SPRING GUIDE SIDE |
| Парткод: | 302HN09100 |
| Деталь: | CURSOR END |
| Парткод: | 302HN09110 |
| Деталь: | LEVER STOPPER |
| Парткод: | 302HN09120 |
| Деталь: | SPRING STOPPER |
| Парткод: | 302HN09130 |
| Деталь: | SHAFT WORKPLATE |
| Парткод: | 302HN09150 |
| Деталь: | GEAR Z50S LIFT |
| Парткод: | 302HN09160 |
| Деталь: | GEAR Z13S JOINT |
| Парткод: | 302HN09170 |
| Деталь: | COVER LIFT GEAR |
| Парткод: | 302HN09180 |
| Деталь: | SPRING FIX |
| Парткод: | 302HN09190 |
| Деталь: | GUIDE RETARD |
| Парткод: | 302HN09230 |
| Деталь: | SIZE FIX |
| Парткод: | 302HN09240 |
| Деталь: | LABEL DIAL |
| Парткод: | 302HN09250 |
| Деталь: | CURSOR LEFT B |
| Парткод: | 302HN09350 |
| Деталь: | SPRING EARTH |
| Парткод: | 302HN09371 |
| Деталь: | SPRING EARTH SIDE |
| Парткод: | 302HN09391 |
| Деталь: | SPRING DIAL |
| Парткод: | 302HN09400 |
| Деталь: | SPRING EARTH C |
| Парткод: | 302HN09410 |
| Деталь: | SPRING RETARD |
| Парткод: | 302HN09430 |
| Деталь: | PLATE BOTTOM ASSY SP |
| Парткод: | 302HN94190 |
| Деталь: | LABEL CURSOR |
| Парткод: | 302HN09420 |
| Деталь: | WORKPLATE LIFT PF |
| Парткод: | 303K809490 |
| Деталь: | CT-501 |
| Парткод: | 302HN93162 |
| Деталь: | CURSOR RIGHT PF ASSY 2HN SP |
| Парткод: | 302HN94300 |
| Деталь: | COVER TOP |
| Парткод: | 302HN04010 |
| Деталь: | STOPPER EXIT |
| Парткод: | 302HN04190 |
| Деталь: | COVER LEFT FRONT |
| Парткод: | 302HN04070 |
| Деталь: | SPRING LEFT LEVER |
| Парткод: | 302HN04300 |
| Деталь: | LEVER FRONT COVER LEFT |
| Парткод: | 302HN04130 |
| Деталь: | COVER UPPER LEFT |
| Парткод: | 302HN04090 |
| Деталь: | SPONGE LEFT COVER |
| Парткод: | 302HN04310 |
| Деталь: | LABEL USB |
| Парткод: | 302HN04320 |
| Деталь: | LABEL WASTE BOTTLE |
| Парткод: | 302HN04340 |
| Деталь: | SPRING SIDE LEVER |
| Парткод: | 302HN04260 |
| Деталь: | LEVER SIDE COVER |
| Парткод: | 302HN04200 |
| Деталь: | HOOK SIDE COVER |
| Парткод: | 302HN04210 |
| Деталь: | SPRING SIDE COVER |
| Парткод: | 302HN04250 |
| Деталь: | SEAL COVER SIDE |
| Парткод: | 302HN04391 |
| Деталь: | HOOK TOP COVER |
| Парткод: | 302HN04230 |
| Деталь: | COVER RIGHT FRONT |
| Парткод: | 302HN04080 |
| Деталь: | SPRING RIGHT LEVER |
| Парткод: | 302HN04290 |
| Деталь: | Cover Right Rear |
| Парткод: | 302HN04041 |
| Деталь: | SPRING RIGHT LID |
| Парткод: | 302HN04280 |
| Деталь: | LID RIGHT COVER |
| Парткод: | 302HN04050 |
| Деталь: | SPRING LEFT COVER |
| Парткод: | 302HN04240 |
| Деталь: | LABEL FUSER CAUTION |
| Парткод: | 302HN04330 |
| Деталь: | SHEET LEVER RIGHT A |
| Парткод: | 302HN04350 |
| Деталь: | SHEET LEVER RIGHT B |
| Парткод: | 302HN04360 |
| Деталь: | COVER LEFT REAR ASSY SP |
| Парткод: | 302HN94210 |
| Деталь: | COVER SIDE ASSY SP |
| Парткод: | 302HN94340 |
| Деталь: | COVER UPPER RIGHT ASSY SP |
| Парткод: | 302HN94280 |
| Деталь: | LEVER FRONT COVER RIGHT ASSY SP |
| Парткод: | 302HN94270 |
Коды ошибок
0100
0110
0120
0150
0170
0420
0600
0610
0640
0930
1010
1020, 1030, 1040
1500, 1520, 1540
1510, 1530, 1550
1600, 1620, 1640
1610, 1630, 1650
2102
2250
2500
2610, 2620, 2630
2830
4001
4002
4201
4202
4203
4204
4600
4700
5301
5302
5303
5304
6000
6020
6030
6400
7001
7002
7003
7004
7401
7402
7403
7404
7411
7412
7413
7414
9530
F000
F010
F020
F030
F040
F050
F186
Описание
| Error code: | 0100 |
| Display: | MAINTENANCE CALL 0100 |
| Description: | Backup memory device error |
| Causes: | Defective flash memory. Defective main PWB. |
| Remedy: | EEPROM (main PWB) 1. Turn the main power swtch off and after 5 seconds, then turn power on. 2. Check that the EEPROM on the main circuit PWB is peroperly installed on the main circuit PWB and, if not, re-install it. 3. Replace the main PWB |
| Error code: | 0110 |
| Description: | Input value from Linear Encoder is not changed by the Linear Encoder origin setup. When Motor stops during printing, expected movement is not completed on some head. |
| Causes: | Read error of Linear Encoder. Read error of Encoder on Scan Motor side. Belt is not fixed to Head Carriage firmly. |
| Remedy: | Confirm whether Encoder Scale is between the slit of Encoder Module in a whole width of the machine. Check cable connection between Linear Encoder Board and Head Board Confirm connection between Belt and Carriage Linear Encoder replacement Scan Motor replacement Servo Board replacement Main Board replacement |
| Error code: | 0120 |
| Description: | There is a problem with Thermistor for Pre-Heater. |
| Causes: | Thermistor Cable has short circuited or cutline. Thermistor has a problem. |
| Remedy: | Check Cable connection around Thermistor Thermistor replacement |
| Error code: | 0150 |
| Description: | Even though the machine carries out the regular movement, the output of Slider Sensor does not reach the expected value. |
| Causes: | Slider Motor has a problem. Slider Sensor has a problem. Wiring or Flexible Cable has short circuitted or cut-line. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Slider Motor replacement Slider Sensor replacement Wiring or Flexible Cable replacement Servo Board replacement |
| Error code: | 0170 |
| Description: | Even though the machine carries out the regular movement, the output of Supply Pump 1 Sensor does not reach the expected value. |
| Causes: | Supply Pump 1 Motor has a problem. Supply Pump 1 Sensor has a problem. Supply Pump 1 Magnet has dropped out. Wiring or Flexible Cable has short circuitted or cut-line. Pump Drive Board has a problem. Servo Board has a problem. |
| Remedy: | Check Cable connection of Servo Board Check Cable connection of Junction Board Check Supply Pump 1 Magnet Supply Pump 1 Motor replacement Supply Pump 1 Sensor replacement Wiring or Flexible Cable replacement Pump Drive Board replacement Servo Board replacement |
| Error code: | 0420 |
| Description: | Paper feeder communication error Communication error between control PWB and optional paper feeder. |
| Causes: | Improper installation paper feeder. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Defective control PWB Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Defective PF main-PWB. |
| Remedy: | Improper installation paper feeder. Follow installation instruction carefully again. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Defective control PWB. Replace the control PWB. Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness (Refer to the service manual for the paper feeder). Defective PF main- PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). |
| Error code: | 0600 |
| Display: | Print Unable 06 Turn the power off and then back on again. |
| Description: | Expanded memory (DIMM) installing error The expansion memory modules (DIMM) are not correctly mounted. |
| Causes: | Improper installation expanded memory (DIMM). |
| Remedy: | Improper installation expanded memory (DIMM). Check the installation of the expanded memory (DIMM). |
| Error code: | 0610 |
| Description: | Expanded memory (DIMM) error The expansion memory modules (DIMM) mounted on the main PWB does not operate correctly. |
| Causes: | Defective expanded memory (DIMM). Defective main PWB. |
| Remedy: | Defective expanded memory (DIMM). Replace the expanded memory (DIMM) and check for correct operation. Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | 0640 |
| Description: | Hard disk error The hard disk cannot be accessed. |
| Causes: | Defective hard disk. Defective main PWB. |
| Remedy: | HDD 1. If an abnormal noise is heard from the HDD, replace the HDD. 2. Check the SATA wiring between the HDD and the main circuit PWB for loose connection, disconnection and damages, and that it is connected into the correct terminal. Main PWB: YC1,YC27 3. Replace the SATA cable. 4. Execute U024 to initialize (FULL) the HDD. 5. If an error is detected after executing U024, replace the HDD. Lack of HDD capacity 1. Confirm the total capacity of the HDD if it is more than 320GB. Change the HDD or add it in case of lacking in capacity. Main PWB Replace the main PWB. |
| Error code: | 0930 |
| Description: | EEPROM bus error |
| Causes: | Defective drum PWB (EEPROM). Defective engine PWB (EEPROM). Defective engine PWB. Defective main PWB. |
| Remedy: | Defective drum PWB (EEPROM). Replace the drum unit. Defective engine PWB (EEPROM). Replace the engine PWB and check for correct operation. Defective engine PWB. Replace the engine PWB and check for correct operation. Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | 1010 |
| Display: | Problem with Printhead L/R Chk printing results |
| Description: | Lift motor 1 error After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 4 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 4 times successively. |
| Causes: | Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective lift motor 1. Defective engine PWB. |
| Remedy: | Cassette lift base elevating mechanism Check that the cassette base can be manipulated smoothly, if not, repair or replace. Lift motor 1 1. Check that the cassette base has been ascended. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift motor 1 and Feed PWB 2 (YC3) Feed PWB 2 (YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the lift motor 1. Lift sensor 1 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Lift sensor 1 and Feed PWB 2 (YC8) Feed PWB 2 (YC1) and Engine PWB (YC4) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the lift sensor1. Feed PWB 2 Replace the Feed PWB 2. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 1020, 1030, 1040 |
| Description: | PF lift motor error (Option paper feeder) When the PF lift motor is driven, the PF lift motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. After the PF lift motor is driven, the ON status of PF lift limit sensor cannot be detected for 8 seconds. The cassette installed confirmation message is displayed on the printer operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively. 1020: Paper feeder 1 1030: Paper feeder 2 1040: Paper feeder 3 |
| Causes: | Defective harness between PF lift motor and PF main PWB (YC7), or improper connector insertion. Defective bottom plate elevation mechanism in the cassette. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF lift limit sensor. Defective PF cassette size switch. Defective PF main PWB. Defective engine PWB. |
| Remedy: | Defective harness between PF lift motor and PF main PWB (YC7), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. (Refer to the service manual for the paper feeder). Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.(Refer to the service manual for the paper feeder). Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.(Refer to the service manual for the paper feeder). Defective PF lift motor. Replace the PF lift motor. (Refer to the service manual for the paper feeder). Defective PF lift limit sensor. Replace the PF main PWB (Refer to the service manual for the paper feeder). Defective PF cassette size switch. Replace the PF cassette size switch.(Refer to the service manual for the paper feeder). Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). Defective engine PWB. Replace the engine PWB. |
| Error code: | 1500, 1520, 1540 |
| Description: | PF warm air heater (upper blower) high temperature error* (Option paper feeder) A temperature higher than 85°C/185°F is detected. *: Multi purpose feeder only 1500: Paper feeder 1 1520: Paper feeder 2 1540: Paper feeder 3 |
| Causes: | The inlet of upper blower assembly is blocked by paper pieces or the like. Defective harness between PF warm air fan motor 2 and PF main PWB (YC11), or improper connector insertion. Shorted PF thermistor 2. Defective PF warm air fan motor 2. Defective PF main PWB. Defective engine PWB. |
| Remedy: | The inlet of upper blower assembly is blocked by paper pieces or the like. Check visually and remove it, if any (Refer to the service manual for the paper feeder). Defective harness between PF warm air fan motor 2 and PF main PWB (YC11), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. (Refer to the service manual for the paper feeder). Shorted PF thermistor 2. Replace the PF thermistor 2 (Refer to the service manual for the paper feeder). Defective PF warm air fan motor 2. Replace the PF warm air fan motor 2 (Refer to the service manual for the paper feeder). Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). Defective engine PWB. Replace the engine PWB. |
| Error code: | 1510, 1530, 1550 |
| Description: | PF warm air heater (side blower) high temperature error* (Option paper feeder) A temperature higher than 85°C/185°F is detected. *: Multi purpose feeder only 1510: Paper feeder 1 1530: Paper feeder 2 1550: Paper feeder 3 |
| Causes: | The inlet of side blower assembly is blocked by paper pieces or the like. Defective harness between PF warm air fan motor 1 and PF main PWB (YC11), or improper connector insertion. Shorted PF thermistor 1. Defective PF warm air fan motor 1. Defective PF main PWB. Defective engine PWB. |
| Remedy: | The inlet of side blower assembly is blocked by paper pieces or the like. Check visually and remove it, if any (Refer to the service manual for the paper feeder). Defective harness between PF warm air fan motor 1 and PF main PWB (YC11), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. (Refer to the service manual for the paper feeder). Shorted PF thermistor 1. Replace the PF thermistor 1. (Refer to the service manual for the paper feeder). Defective PF warm air fan motor 1. Replace the PF warm air fan motor 1 (Refer to the service manual for the paper feeder). Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). Defective engine PWB. Replace the engine PWB. |
| Error code: | 1600, 1620, 1640 |
| Description: | PF warm air heater (upper blower) low temperature error* (Option paper feeder) An external temperature higher than +5°C/+41°F is not detected when one minute elapses after PF warm air heater 2 is turned on. *: Multi purpose feeder only 1600: Paper feeder 1 1620: Paper feeder 2 1640: Paper feeder 3 |
| Causes: | Defective harness between PF warm air heater 2 and PF warm air heater driver PWB (YC2), or improper connector insertion. Defective harness between PF warm air heater driver PWB (YC3) and PF main PWB (YC13), or improper connector insertion. Defective harness between PF thermistor 2 and PF main PWB (YC12), or improper connector insertion. PF thermistor 2 installed incorrectly. Defective PF thermistor 2. PF thermal cutout 2 triggered. Broken PF warm air heater 2. Defective PF warm air heater driver PWB. Defective PF main PWB. Defective engine PWB. |
| Remedy: | Defective harness between PF warm air heater 2 and PF warm air heater driver PWB (YC2), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. (Refer to the service manual for the paper feeder). Defective harness between PF warm air heater driver PWB (YC3) and PF main PWB (YC13), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. (Refer to the service manual for the paper feeder). Defective harness between PF thermistor 2 and PF main PWB (YC12), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. (Refer to the service manual for the paper feeder). PF thermistor 2 installed incorrectly. Check the installation of the PF thermistor 2 and remedy if necessary (Refer to the service manual for the paper feeder). Defective PF thermistor 2. Replace the PF thermistor 2 (Refer to the service manual for the paper feeder). PF thermal cutout 2 triggered. Replace the PF thermal cutout 2 (Refer to the service manual for the paper feeder). Broken PF warm air heater 2. Replace the PF warm air heater 2 (Refer to the service manual for the paper feeder). Defective PF warm air heater driver PWB. Replace the PF warm air driver PWB (Refer to the service manual for the paper feeder). Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). Defective engine PWB. Replace the engine PWB. |
| Error code: | 1610, 1630, 1650 |
| Description: | PF warm air heater (side blower) error* (Option paper feeder) An external temperature higher than +5°C/+41°F is not detected when one minute elapses after PF warm air heater 2 is turned on. *: Multi purpose feeder only 1610: Paper feeder 1 1630: Paper feeder 2 1650: Paper feeder 3 |
| Causes: | Defective harness between PF warm air heater 1 and PF warm air heater driver PWB (YC1), or improper connector insertion. Defective harness between PF warm air heater driver PWB (YC3) and PF main PWB (YC13), or improper connector insertion. Defective harness between PF thermistor 2 and PF main PWB (YC12), or improper connector insertion. PF thermistor 1 installed incorrectly. Defective PF thermistor 1. PF thermostat 1 triggered. Broken PF warm air heater 1. Defective PF warm air heater driver PWB. Defective PF main PWB. Defective engine PWB. |
| Remedy: | Defective harness between PF warm air heater 1 and PF warm air heater driver PWB (YC1), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. (Refer to the service manual for the paper feeder). Defective harness between PF warm air heater driver PWB (YC3) and PF main PWB (YC13), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.(Refer to the service manual for the paper feeder). Defective harness between PF thermistor 2 and PF main PWB (YC12), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. (Refer to the service manual for the paper feeder). PF thermistor 1 installed incorrectly. Check the installation of the PF thermistor 1 and remedy if necessary (Refer to the service manual for the paper feeder). Defective PF thermistor 1. Replace the PF thermistor 1 (Refer to the service manual for the paper feeder). PF thermostat 1 triggered. Replace the PF thermostat 1 (Refer to the service manual for the paper feeder). Broken PF warm air heater 1. Replace the PF warm air heater 1 (Refer to the service manual for the paper feeder). Defective PF warm air heater driver PWB. Replace the PF warm air driver PWB (Refer to the service manual for the paper feeder). Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). Defective engine PWB. Replace the engine PWB. |
| Error code: | 2102 |
| Description: | Developer motor C error After developer motor C is driven, the ready signal does not turn to L within 5 s. After developer motor C is stabilized, the ready signal is at the H level for 5 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective developer motor C. Defective engine PWB. |
| Remedy: | Developer unit C 1. Check that the developer waste lock has been released and, if not, release the lock. 2. Check that the gears and spiral screw of the developer unit are not damaged. 3. Confirm that the developer roller can rotate. 4. If it won`t rotate, replace the developer unit. Developer motor C 1. To check the motor operation, execute DLP(C) by U030. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer motor C and Motor control PWB (YC7) Motor control PWB (YC3) and Engine PWB (YC9) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Developer motor C. Motor control PWB Replace the Motor control PWB Engine PWB. 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2250 |
| Description: | Main charger cleaning motor error When the main charger cleaning motor is driven, the main charger cleaning motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. |
| Causes: | Defective harness between main charger cleaning motor and engine PWB (YC36), or improper connector insertion. Defective drive transmission system of the main charger cleaning motor. Defective main charger cleaning motor. Defective engine PWB. |
| Remedy: | Defective harness between main charger cleaning motor and engine PWB (YC36), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Defective drive transmission system of the main charger cleaning motor. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Defective main charger cleaning motor. Replace the main charger cleaning motor. Defective engine PWB. Replace the engine PWB. |
| Error code: | 2500 |
| Description: | Paper feed motor error After paper feed motor is driven, the ready signal does not turn to L within 2 s. After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective paper feed motor. Defective engine PWB. |
| Remedy: | Paper feed motor 1. To check the motor operation execute U030 Feed (paper feed motor). 2. Check the paper feed roller and drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Paper feed motor and Feed PWB 2(YC2) Feed PWB 2(YC1) and Engine PWB (YC4) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the paper feed motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 2610, 2620, 2630 |
| Description: | PF paper feed motor error (Option paper feeder) The PF paper feed motor of paper feeder 1 ready input is not given for 2 seconds during the PF paper feed motor is ON. 2610: Paper feeder 1 2620: Paper feeder 2 2630: Paper feeder 3 |
| Causes: | Defective harness between PF paper feed motor and PF main PWB (YC6), or improper connector insertion. Defective PF paper feed motor drive transmission system. Defective PF main motor. Defective PF main PWB. Defective printer’s engine PWB. |
| Remedy: | Defective harness between PF paper feed motor and PF main PWB (YC6), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. (Refer to the service manual for the paper feeder). Defective PF paper feed motor drive transmission system. Check if the gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. (Refer to the service manual for the paper feeder). Defective PF main motor. Replace the PF main motor. Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder). Defective printer’s engine PWB. Replace the printer’s engine PWB (Refer to the service manual for the printer). |
| Error code: | 2830 |
| Display: | Left printhead error. Open top cover and replace the left printhead. |
| Description: | Developing motor K error The developing motor K ready input is not given for 5 seconds during the developing motor K is ON. |
| Causes: | Defective harness between developing motor K and engine PWB (YC26), or improper connector insertion. Defective drive transmission system of the developing motor K. Improper installation intermediate transfer unit. Defective developing motor K. Defective engine PWB. |
| Remedy: | Defective harness between developing motor K and engine PWB (YC26), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Defective drive transmission system of the developing motor K. Check if the gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Improper installation intermediate transfer unit. Check the installation of the intermediate transfer unit and reinstall them if necessary. Defective developing motor K. Replace the developing motor K. Defective engine PWB. Replace the engine PWB. |
| Error code: | 4001 |
| Display: | ERROR E146-4001 Call for service. |
| Description: | Polygon motor synchronization error After polygon motor is driven, the ready signal does not turn to L within 30 s. The polygon motor speed won’t stabilize within 10 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| Remedy: | Polygon motor (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor and Engine PWB (YC15) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4002 |
| Display: | Drum End Soon:Y |
| Description: | Polygon motor C synchronization error After polygon motor C is driven, the ready signal does not turn to L within 30 s. The polygon motor speed won’t stabilize within 10 s. |
| Causes: | Defective connector cable or poor contact in the connector. Defective polygon motor C. Defective engine PWB. |
| Remedy: | Polygon motor C (LSU) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Polygon motor C and LSU relay PWB (YC9) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4201 |
| Display: | Replace Drum:BK |
| Description: | BD steady-state error K The BD signal is not detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB. Defective engine PWB. |
| Remedy: | PD PWB K (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and Engine PWB (YC11) 2. If the FFC wiring is disconnected, shorted or grounded, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4202 |
| Display: | Replace Drum:Y |
| Description: | BD steady-state error C The BD signal is not detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB C. Defective engine PWB. |
| Remedy: | PD PWB C (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC10) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4203 |
| Display: | Replace Drum:M |
| Description: | BD steady-state error M The BD signal is not detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB M. Defective engine PWB. |
| Remedy: | PD PWB M (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC8) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4204 |
| Display: | Replace Drum:C |
| Description: | BD steady-state error Y The BD signal is not detected. |
| Causes: | Defective connector cable or poor contact in the connector. Defective PD PWB Y. Defective engine PWB |
| Remedy: | PD PWB Y (LSU) 1. Confirm that the FFC wiring connector is not distorted and connect the FFC wiring all the way in. Laser scanner unit and LSU relay PWB (YC12) LSU relay PWB (YC3) and Engine PWB (YC12) 2. If the FFC wiring is disconnected, replace the FFC wiring. 3. Replace the laser scanner unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4600 |
| Display: | Maintenance Replace Laser |
| Description: | LSU cleaning motor error After LSU cleaning motor is driven, the ready signal does not turn to L within 2 s. After LSU cleaning motor is stabilized, the ready signal is at the H level for 1 s continuously. |
| Causes: | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective LSU cleaning motor. Defective engine PWB. |
| Remedy: | LSU cleaning motor 1. Execute LSU cleaning using Adjustment/Maintenance of the system menu. 2. Rotate the drive gear and the cleaning spiral by the hand and check that they are not unusually loaded, and replace if it is damaged. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. LSU cleaning motor and Engine PWB (YC21) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the LSU cleaning motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 4700 |
| Display: | Supplies WT Box End Soon |
| Description: | VIDEO_ASIC device error Communication with the video ASIC has failed 5 times successively. After writing to the VIDEO ASIC, the error that the reading value from the same address does not match occurs 8 times successively. |
| Causes: | Engine PWB. Main PWB |
| Remedy: | Main PWB 1. Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. 2. Check that the connectors on the main PWB are properly connected, and if not, re-connect them. 3. Replace the main PWB. |
| Error code: | 5301 |
| Description: | Broken cleaning lamp K wire When the cleaning lamp K is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective cleaning lamp K. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit K and Drum relay PWB (YC2) Drum relay PWB (YC1) and engine PWB (YC34) Defective cleaning lamp K. Replace the drum unit K. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 5302 |
| Description: | Broken cleaning lamp C wire When the cleaning lamp C is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective cleaning lamp C. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit C and Drum relay PWB (YC4) Drum relay PWB (YC1) and engine PWB (YC34) Defective cleaning lamp C. Replace the drum unit C. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 5303 |
| Description: | Broken cleaning lamp M wire When the cleaning lamp M is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective cleaning lamp M. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit M and Drum relay PWB (YC3) Drum relay PWB (YC1) and engine PWB (YC34) Defective cleaning lamp M. Replace the drum unit M. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 5304 |
| Description: | Broken cleaning lamp Y wire When the cleaning lamp Y is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. |
| Causes: | Defective connector cable or poor contact in the connector. Defective cleaning lamp Y. Defective engine PWB. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit Y and Drum relay PWB (YC5) Drum relay PWB (YC1) and engine PWB (YC34) Defective cleaning lamp Y. Replace the drum unit Y. Defective engine PWB. Replace the engine PWB and check for correct operation. |
| Error code: | 6000 |
| Description: | Broken fuser heater wire Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Power source PWB 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Power source PWB (YC3) and fuser heater PWB (YC3) Fuser heater PWB (YC2) and feed PWB 1 (YC27) Feed PWB 1 (YC1) and Engine PWB (YC6) Fuser heater 1. Replace the fuser unit. |
| Error code: | 6020 |
| Description: | Abnormally high fuser thermistor 1 temperature Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s. |
| Causes: | Deformed connector pin. Defective triac. Shorted fuser thermistor 1. Defective engine PWB. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 6030 |
| Description: | Broken fuser thermistor 1 wire Input from fuser center thermistor 1 is 1010 or more (A/D value) continuously for 1 s. Verify if A/D read in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a lowtemperature environment. |
| Causes: | Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Defective fuser heater. Defective engine PWB. |
| Remedy: | Fuser unit 1. Check that no paper jam is present. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and Engine PWB (YC26) 3. If the wiring is disconnected, shorted or grounded, replace the wiring. 4. Replace the Fuser unit. (Deteriorated sensitivity due to the toner adhered to the center thermistor.) Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. Fuser thermistor 1 1. Replace the Fuser unit. Fuser thermostat (triggered) 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser unit and fuser heater PWB (YC1) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the Fuser unit. |
| Error code: | 6400 |
| Display: | No Belt Unit Open the Front Cover, pull out all Drum Units completely and install the Belt Unit. |
| Description: | Zero-cross signal error While fuser heater ON/OFF control is performed, the zerocross signal is not input within 3 s. |
| Causes: | Fuser unit. |
| Remedy: | Fuser unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Fuser heater PWB (YC2) and feed PWB 1 (YC27) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the fuser heater PWB. |
| Error code: | 7001 |
| Description: | Toner motor error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective toner motor. Defective engine PWB. |
| Remedy: | Toner container 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor. Screw sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor and Front PWB (YC5) Front PWB (YC2) and Engine PWB (YC7) 3. Replace the Screw sensor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7002 |
| Description: | Toner motor C error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor C. Defective toner motor C. Defective engine PWB. |
| Remedy: | Toner container C 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor C 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor C and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor C. Screw sensor C 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor C and Engine PWB (YC27) 3. Replace the screw sensor C. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7003 |
| Description: | Toner motor M error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor M. Defective toner motor M. Defective engine PWB. |
| Remedy: | Toner container M 1. Check that the spiral screw of the toner container can be rotated by the hand. 2. Check for broken gears and replace if any. Toner motor M 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor M and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor M. Screw sensor M 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor M and Engine PWB (YC27) 3. Replace the screw sensor M. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7004 |
| Description: | Toner motor Y error During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets. |
| Causes: | Defective connector cable or poor contact in the connector. Defective screw sensor Y. Defective toner motor Y. Defective engine PWB. |
| Remedy: | Toner container Y 1. Check that the spiral screw of the toner container can be rotated by the hand. 1. Check for broken gears and replace if any. Toner motor Y 1. Draw out the toner container and execute U135 to check the toner motor operation. 2. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 3. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Toner motor Y and Engine PWB (YC27) 4. If the wiring is disconnected, shorted or grounded, replace the wiring. 5. Replace the Toner motor Y. Screw sensor Y 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Screw sensor Y and Engine PWB (YC27) 3. Replace the screw sensor Y. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB. |
| Error code: | 7401 |
| Description: | Developer unit type mismatch error Improper adaptation of the machine and developer unit is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
| Remedy: | Different type of the developer unit is installed. Install the developer unit of the correct type. Developer unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Developer unit and Front PWB (YC7) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
| Error code: | 7402 |
| Description: | Developer unit C type mismatch error Absence of the developer unit C is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit C and front PWB (YC13) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
| Error code: | 7403 |
| Description: | Developer unit M type mismatch error Absence of the developer unit M is detected. |
| Causes: | Defective connector cable or poor contact in the connector Different type of the developer unit is installed |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit M and front PWB (YC11) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
| Error code: | 7404 |
| Description: | Developer unit Y type mismatch error Absence of the developer unit Y is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the developer unit is installed. |
| Remedy: | Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit Y and front PWB (YC15) Front PWB (YC2) and engine PWB (YC10) Different type of the developer unit is installed. Install the correct developer unit. |
| Error code: | 7411 |
| Description: | Drum unit type mismatch error Improper adaptation of the machine and developer unit is detected. |
| Causes: | Defective connector cable or poor contact in the connector. Different type of the drum unit is installed. |
| Remedy: | Different type of the drum unit is installed. Install the drum unit of the correct type. Drum unit 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. Drum unit and Front PWB (YC6) Front PWB (YC2) and Engine PWB (YC8) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. |
| Error code: | 7412 |
| Description: | Drum unit type Mismatch error (Cyan) Improper adaptation of the main unit and drum unit is detected. |
| Causes: | Drum unit C |
| Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7413 |
| Description: | Drum unit type Mismatch error (Magenta) Improper adaptation of the main unit and drum unit is detected. |
| Causes: | Drum unit M |
| Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 7414 |
| Description: | Drum unit type Mismatch error (Yellow) Improper adaptation of the main unit and drum unit is detected. |
| Causes: | Drum unit Y |
| Remedy: | Drum unit 1. Check if the drum unit of different models is attached, and replace it to the correct one. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Drum unit - Drum/Developer relay PWB Drum/Developer relay PWB - Engine PWB(YC6) 3. If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. Drum/developer relay PWB Replace the drum/developer relay PWB Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the engine PWB. |
| Error code: | 9530 |
| Description: | Machine No.backup error C |
| Causes: | IPU PWB error |
| Remedy: | Contact the Service Administrative Division. |
| Error code: | F000 |
| Description: | Communication error between the main unit and CPU |
| Causes: | The panel cannot be detected since the CPU communication between the main PWB and the operation panel main PWB is unavailable. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 3 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 4 Replacing the main PWB The main PWB is faulty. Replace the main PWB. 5 Replacing the operation panel main PWB The operation panel main PWB is faulty. Replace the panel main PWB. |
| Error code: | F010 |
| Description: | Program read error (SSD) |
| Causes: | The garbled 2bit data was detected during the program read from the flash memory. |
| Remedy: | 1 (When the service call error appears after replacing the SSD) Replacing the SSD along the correct procedures The firmware is not stored in the SSD. Insert the USB memory device containing all released firmware into the main unit, and turn the main power on. Firmware Update 2 Checking the SSD (if lit after replacing the SSD) An SSD out of specification is installed. Install the SSD matching the memory capacity specification. 3 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 4 Checking the SSD The SSD is not properly attached. Check if the SSD terminal is not faulty and clean it. Then, reinstall the SSD. 5 Checking the connection The connector is not properly connected. The wire or the SATA cable is faulty. Clean the terminal of the following SATA cable connector and the wire connectors and reconnect the connectors. If there is no continuity, replace the SATA cable or the wire. • Main PWB - Operation panel main PWB Wiring diagram 6 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 7 Replacing the SSD The SSD is faulty. Backup the data in the SSD at U026. Then, replace the SSD and turn the main power on while installing the USB memory storing the firmware for the affected model n the main unit. 8 Replacing the main PWB The main PWB is faulty. Replace the main PWB. |
| Error code: | F020 |
| Description: | System memory error (RAM reading/writing error or CPU memory error) |
| Causes: | The error appears during the reading/writing check of the RAM for the CPU when the main unit starts up. |
| Remedy: | 1 Resetting the main power The communication between the main PWB and the operation panel main PWB is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 2 Executing U021 The backup RAM data is faulty. Execute U021 to initialize the backup RAM data. Executing U021 3 Checking the main PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the main PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the main PWB. |
| Error code: | F030 |
| Description: | Main PWB system error |
| Causes: | Defective main PWB. |
| Remedy: | Defective main PWB. Replace the main PWB and check for correct operation. |
| Error code: | F040 |
| Description: | Option installation error |
| Causes: | The size of the attached main memory is 2 GB when the DSDF is installed. |
| Remedy: | Main memory Replace the main memory with a 4 GB one. DSDF • Remove the DSDF. • Replace the DSDF with an RADF. |
| Error code: | F050 |
| Description: | Engine main program error |
| Causes: | The engine program cannot start up. |
| Remedy: | 1 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Update 2 Resetting the main power The print engine ROM checksum is faulty. Remove the original and check the sensor. Next, turn off the power switch and main switch. Then, turn on the main switch and power switch when passing 5 seconds. 3 Checking the EEPROM The EEPROM is not properly attached. Reattach the EEPROM. 4 Checking the engine PWB The connector or the FFC is not properly connected. The wire, the FFC or the PWB is faulty. Clean the connectors on the engine PWB and the FFC terminal. Then, reconnect the wire connector and the FFC. At that time, if the wire is pinched by other parts or it is damaged, repair or replace the wire. If the FFC terminal section is deformed or FFC is broken, replace the FFC. If the issue is not resolved, replace the engine PWB. |
| Error code: | F186 |
| Description: | Finisher Interface Error |
| Causes: | • Finisher Control Board • Finisher Interconnect Cable • Engine Control Board, PL1.1.4 |
| Remedy: | 1 Check the following for evidence of fault or damage: • Finisher Interconnect Cable • Finisher connections Is there any damage? Replace any damaged parts. Go to Step 2. 2 Check all the pins of the Finisher Interconnect Cable for continuity. Is the cable conductive? Go to Step 3. Replace the cable. 3 Check all the pins of the OPTIF Harness for continuity. Is the harness conductive? Go to Step 4. Replace the OPTIF harness. 4 Replace the Finisher Control Board. Does the error persists? Replace the Engine Control Board Complete. |
Название
Kyocera Блок фотобарабана
Kyocera Блок проявки голубой /Developer Unit C/
Kyocera Блок проявки черный /Developer Unit K/
Kyocera Блок проявки пурпурный /Developer Unit M/
Kyocera Блок проявки желтый /Developer Unit Y/
Kyocera Узел термозакрепления 230v
Kyocera Сервисный комплект
Kyocera Тонер-картридж голубой.
Kyocera Тонер-картридж черный.
Kyocera Тонер-картридж пурпурный.
Kyocera Тонер-картридж желтый.
